Tech-invite3GPPspaceIETFspace
21222324252627282931323334353637384‑5x

Content for  TS 38.413  Word version:  18.2.0

Top   Top   Up   Prev   Next
1…   4…   8…   8.2…   8.2.3…   8.3…   8.3.4…   8.4…   8.4.3…   8.5…   8.7…   8.8…   8.10…   8.12…   8.17…   9…   9.2…   9.2.2…   9.2.3…   9.2.4…   9.2.6…   9.2.7…   9.2.9…   9.2.11…   9.2.16…   9.2.17…   9.3…   9.3.1.21…   9.3.1.41…   9.3.1.61…   9.3.1.81…   9.3.1.101…   9.3.1.121…   9.3.1.141…   9.3.1.161…   9.3.1.181…   9.3.1.205…   9.3.1.222…   9.3.1.245…   9.3.2…   9.3.3…   9.3.3.21…   9.3.3.42…   9.3.4…   9.3.4.10…   9.3.5…   9.4…   9.4.4   9.4.5   9.4.6…   9.5…   10…

 

9.3.1.81  Packet Error Ratep. 247

This IE indicates the Packet Error Rate for a QoS flow.
IE/Group Name Pre­sence Range IE type and reference Semantics description
ScalarMINTEGER (0..9, …)The packet error rate is expressed as Scalar x 10-k where k is the Exponent.
ExponentMINTEGER (0..9, …)
Up

9.3.1.82  Averaging Windowp. 247

This IE indicates the Averaging Window for a QoS flow, and applies to GBR QoS flows only.
IE/Group Name Pre­sence Range IE type and reference Semantics description
Averaging WindowMINTEGER (0..4095, …)Unit: ms.
The default value of the IE is 2000ms.
Up

9.3.1.83  Maximum Data Burst Volumep. 247

This IE indicates the Maximum Data Burst Volume for a QoS flow, and applies to delay critical GBR QoS flows only.
IE/Group Name Pre­sence Range IE type and reference Semantics description
Maximum Data Burst VolumeMINTEGER (0..4095, …, 4096.. 2000000)Unit: byte.
Up

9.3.1.84  Priority Levelp. 247

This IE indicates the Priority Level for a QoS flow.
IE/Group Name Pre­sence Range IE type and reference Semantics description
Priority LevelMINTEGER (1..127, …)Values ordered in decreasing order of priority, i.e. with 1 as the highest priority and 127 as the lowest priority.
Up

9.3.1.85  Mobility Restriction Listp. 247

This IE defines roaming or access restrictions for subsequent mobility action for which the NG-RAN provides information about the target of the mobility action towards the UE, e.g., handover, or for SCG selection during dual connectivity operation or for assigning proper RNAs. NG-RAN behaviour upon receiving this IE is specified in TS 23.501.
IE/Group Name Pre­sence Range IE type and refe­rence Semantics description Criti­cality Assi­gned Criti­cality
Serving PLMNMPLMN Identity
9.3.3.5
-
Equivalent PLMNs0..<maxnoofEPLMNs>Allowed PLMNs in addition to Serving PLMN.
This list corresponds to the list of "equivalent PLMNs" as defined in TS 24.501.
This list is part of the roaming restriction information. Roaming restrictions apply to PLMNs other than the Serving PLMN and Equivalent PLMNs.
-
>PLMN IdentityM 9.3.3.5-
RAT Restrictions0..<maxnoofEPLMNsPlusOne>This IE contains RAT restriction related information as specified in TS 23.501.-
>PLMN IdentityM 9.3.3.5-
>RAT Restriction InformationMBIT STRING {
e-UTRA (0),
nR (1),
nR-unlicensed (2),
nR-LEO (3),
nR-MEO (4),
nR-GEO (5),
nR-OTHERSAT (6)}
(SIZE(8, …))
Each position in the bitmap represents a RAT.
If a bit is set to "1", the respective RAT is restricted for the UE.
If a bit is set to "0", the respective RAT is not restricted for the UE. Bit 7 reserved for future use.
-
>Extended RAT Restriction InformationO 9.3.1.126If this IE is included, the RAT Restriction Information IE is ignored.YESignore
Forbidden Area Information0..<maxnoofEPLMNsPlusOne>This IE contains Forbidden Area information as specified in TS 23.501.-
>PLMN IdentityM 9.3.3.5-
>Forbidden TACs1..<maxnoofForbTACs>-
>>TACM 9.3.3.10The TAC of the forbidden TAI.-
Service Area Information0..<maxnoofEPLMNsPlusOne>This IE contains Service Area Restriction information as specified in TS 23.501.-
>PLMN IdentityM 9.3.3.5-
>Allowed TACs0..<maxnoofAllowedAreas>-
>>TACM 9.3.3.10The TAC of the allowed TAI.-
>Not Allowed TACs0..<maxnoofAllowedAreas>-
>>TACM 9.3.3.10The TAC of the not-allowed TAI.-
Last E-UTRAN PLMN IdentityOPLMN Identity
9.3.3.5
Indicates the E-UTRAN PLMN ID from where the UE formerly handed over to 5GS and which is preferred in case of subsequent mobility to EPS.YESignore
Core Network Type Restriction for Serving PLMNOENUMERATED (EPCForbidden,…)Indicates whether the UE is restricted to connect to EPC for the Serving PLMN as specified in TS 23.501.YESignore
Core Network Type Restriction for Equivalent PLMNs0..<maxnoofEPLMNs>YESignore
>PLMN IdentityM 9.3.3.5Includes any of the Equivalent PLMNs listed in the Mobility Restriction List IE for which CN Type restriction applies as specified in TS 23.501.-
>Core Network Type RestrictionMENUMERATED (EPCForbidden, 5GCForbidden,…)Indicates whether the UE is restricted to connect to EPC or to 5GC for this PLMN.-
NPN Mobility InformationO 9.3.1.184YESreject
Range bound Explanation
maxnoofEPLMNsMaximum no. of equivalent PLMNs. Value is 15.
maxnoofEPLMNsPlusOneMaximum no. of allowed PLMNs. Value is 16.
maxnoofForbTACsMaximum no. of forbidden Tracking Area Codes. Value is 4096.
maxnoofAllowedAreasMaximum no. of allowed or not allowed Tracking Areas. Value is 16.
Up

9.3.1.86  UE Security Capabilitiesp. 249

This IE defines the supported algorithms for encryption and integrity protection in the UE. The Security Capabilities received from NAS signaling shall not be modified or truncated when forwarded to NG-RAN nodes and the NG-RAN nodes store and send the complete bitmaps without modification or truncation as specified in TS 38.300.
IE/Group Name Pre­sence Range IE type and reference Semantics description
NR Encryption AlgorithmsMBIT STRING (SIZE(16, …)) Each position in the bitmap represents an encryption algorithm:
"all bits equal to 0" - UE supports no other algorithm than NEA0,
"first bit" - 128-NEA1,
"second bit" - 128-NEA2,
"third bit" - 128-NEA3,
"fourth to seventh bit" are mapped from bit 4 to bit 1 of octet 3 in the UE Security Capability IE defined in TS 24.501,
other bits reserved for future use. Value '1' indicates support and value '0' indicates no support of the algorithm.
Algorithms are defined in TS 33.501.
NR Integrity Protection AlgorithmsMBIT STRING (SIZE(16, …)) Each position in the bitmap represents an integrity protection algorithm:
"all bits equal to 0" - UE supports no other algorithm than NIA0,
"first bit" - 128-NIA1,
"second bit" - 128-NIA2,
"third bit" - 128-NIA3,
"fourth to seventh bit" are mapped from bit 4 to bit 1 of octet 4 in the UE Security Capability IE defined in TS 24.501,
other bits reserved for future use.
Value '1' indicates support and value '0' indicates no support of the algorithm.
Algorithms are defined in TS 33.501.
E-UTRA Encryption AlgorithmsMBIT STRING (SIZE(16, …)) Each position in the bitmap represents an encryption algorithm:
"all bits equal to 0" - UE supports no other algorithm than EEA0,
"first bit" - 128-EEA1,
"second bit" - 128-EEA2,
"third bit" - 128-EEA3,
"fourth to seventh bit" are mapped from bit 4 to bit 1 of octet 5 in the UE Security Capability IE defined in TS 24.501,
other bits reserved for future use. Value '1' indicates support and value '0' indicates no support of the algorithm.
Algorithms are defined in TS 33.401.
E-UTRA Integrity Protection AlgorithmsMBIT STRING (SIZE(16, …)) Each position in the bitmap represents an encryption algorithm:
"all bits equal to 0" - UE supports no other algorithm than EIA0,
"first bit" - 128-EIA1,
"second bit" - 128-EIA2,
"third bit" - 128-EIA3,
"fourth to seventh bit" are mapped from bit 4 to bit 1 of octet 6 in the UE Security Capability IE defined in TS 24.501,
other bits reserved for future use. Value '1' indicates support and value '0' indicates no support of the algorithm.
Algorithms are defined in TS 33.401.
Up

9.3.1.87  Security Keyp. 251

This IE is used to apply security in the NG-RAN for different scenarios as defined in TS 33.501.
IE/Group Name Pre­sence Range IE type and reference Semantics description
Security KeyMBIT STRING (SIZE(256))Key material for NG-RAN node or Next Hop Key as defined in TS 33.501
Up

9.3.1.88  Security Contextp. 251

This IE provides security related parameters to the NG-RAN node which are used to derive security keys for user plane traffic and RRC signalling messages and for security parameter generation for subsequent mobility, see TS 33.501.
IE/Group Name Pre­sence Range IE type and reference Semantics description
Next Hop Chaining CountMINTEGER (0..7)Next Hop Chaining Counter (NCC) defined in TS 33.501.
Next-Hop NHMSecurity Key 9.3.1.87The NH together with the NCC is used to derive the security configuration as defined in TS 33.501.
Up

9.3.1.89  IMS Voice Support Indicatorp. 251

This IE is set by the NG-RAN node to indicate whether the UE radio capabilities are compatible with the network configuration for IMS voice.
IE/Group Name Pre­sence Range IE type and reference Semantics description
IMS Voice Support IndicatorMENUMERATED (Supported, Not Supported, …)
Up

9.3.1.90  Paging DRXp. 251

This IE indicates the Paging DRX as defined in TS 38.304 and TS 36.304.
IE/Group Name Pre­sence Range IE type and reference Semantics description
Paging DRXMENUMERATED (32, 64, 128, 256, …)Unit: [number of radioframes]
Up

9.3.1.91  RRC Inactive Transition Report Requestp. 252

This IE is used to request the NG-RAN node to report or stop reporting to the 5GC when the UE enters or leaves RRC_INACTIVE state.
IE/Group Name Pre­sence Range IE type and reference Semantics description
RRC Inactive Transition Report RequestMENUMERATED (Subsequent state transition report, Single RRC connected state report, Cancel report, …)
Up

9.3.1.92  RRC Statep. 252

This IE indicates the RRC state of the UE.
IE/Group Name Pre­sence Range IE type and reference Semantics description
RRC StateMENUMERATED (Inactive, Connected, …)Indicates the current RRC state of the UE.
Up

9.3.1.93  Expected UE Behaviourp. 252

This IE indicates the behaviour of a UE with predictable activity and/or mobility behaviour, to assist the NG-RAN node in e.g. determining the optimum RRC connection time or helping with the RRC_INACTIVE state transition and RNA configuration (e.g. size and shape of the RNA).
IE/Group Name Pre­sence Range IE type and reference Semantics description
Expected UE Activity BehaviourO 9.3.1.94
Expected HO IntervalOENUMERATED (sec15, sec30, sec60, sec90, sec120, sec180, long-time, …)Indicates the expected time interval between inter NG-RAN node handovers.
If "long-time" is included, the interval between inter NG-RAN node handovers is expected to be longer than 180 seconds.
Expected UE MobilityOENUMERATED (stationary, mobile, ...)Indicates whether the UE is expected to be stationary or mobile.
Expected UE Moving Trajectory0..1Indicates the UE's expected geographical movement.
>Expected UE Moving Trajectory Item1..<maxnoofCellsUEMovingTrajectory>Includes list of visited and non-visited cells, where visited cells are listed in the order the UE visited them with the most recent cell being the first in the list. Non-visited cells are included immediately after the visited cell they are associated with.
>>NG-RAN CGIM 9.3.1.73
>>Time Stayed in Cell OINTEGER (0..4095)Included for visited cells and indicates the time a UE stayed in a cell in seconds. If the UE stays in a cell more than 4095 seconds, this IE is set to 4095.
Range bound Explanation
maxnoofCellsUEMovingTrajectoryMaximum no. of cells of UE moving trajectory. Value is 16.
Up

9.3.1.94  Expected UE Activity Behaviourp. 253

This IE indicates information about the expected "UE activity behaviour" of the UE or the PDU session as defined in TS 23.501.
IE/Group Name Pre­sence Range IE type and reference Semantics description
Expected Activity PeriodOINTEGER (1..30|40|50|60|80| 100|120|150|180| 181, ...) If set to "181" the expected activity time is longer than 180 seconds.
The remaining values indicate the expected activity time in [seconds].
Expected Idle PeriodOINTEGER (1..30|40|50|60|80| 100|120|150|180| 181, ...) If set to "181" the expected idle time is longer than 180 seconds.
The remaining values indicate the expected idle time in [seconds].
Source of UE Activity Behaviour InformationOENUMERATED (subscription information, statistics, ...) If "subscription information" is indicated, the information contained in the Expected Activity Period IE and the Expected Idle Period IE, if present, is derived from subscription information. If "statistics" is indicated, the information contained in the Expected Activity Period IE and the Expected Idle Period IE, if present, is derived from statistical information.
Up

9.3.1.95  UE History Informationp. 254

This IE contains information about cells that a UE has been served by in active state prior to the target cell.
IE/Group Name Pre­sence Range IE type and reference Semantics description
Last Visited Cell Item1..<maxnoofCellsinUEHistoryInfo>Most recent information is added to the top of this list.
>Last Visited Cell InformationM 9.3.1.96
Range bound Explanation
maxnoofCellsinUEHistoryInfoMaximum no. of cells in the UE history information. Value is 16.
Up

9.3.1.96  Last Visited Cell Informationp. 254

This IE may contain cell specific information.
IE/Group Name Pre­sence Range IE type and reference Semantics description
CHOICE Last Visited Cell InformationM
>NG-RAN Cell
>>Last Visited NG-RAN Cell InformationM 9.3.1.97
>E-UTRAN Cell
>>Last Visited E-UTRAN Cell InformationMOCTET STRINGDefined in TS 36.413.
>UTRAN Cell
>>Last Visited UTRAN Cell InformationMOCTET STRINGDefined in TS 25.413.
>GERAN Cell
>>Last Visited GERAN Cell InformationMOCTET STRINGDefined in TS 36.413.
Up

9.3.1.97  Last Visited NG-RAN Cell Informationp. 255

This IE contains information about a cell. In case of NR cell, this IE contains information about a set of NR cells with the same NR ARFCN for reference point A, and the Global Cell ID IE identifies one of the NR cells in the set. The information is to be used for RRM purposes.
IE/Group Name Pre­sence Range IE type and refe­rence Semantics description Criti­cality Assi­gned Criti­cality
Global Cell IDMNG-RAN CGI
9.3.1.73
-
Cell TypeM 9.3.1.98-
Time UE Stayed in CellMINTEGER (0..4095)The duration of time the UE stayed in the cell, or set of NR cells with the same NR ARFCN for reference point A, in seconds. If the duration is more than 4095s, this IE is set to 4095.-
Time UE Stayed in Cell Enhanced GranularityOINTEGER (0..40950)The duration of time the UE stayed in the cell, or set of NR cells with the same NR ARFCN for reference point A, in 1/10 seconds. If the duration is more than 4095s, this IE is set to 40950.-
HO Cause ValueOCause
9.3.1.2
The cause for the handover.-
Last Visited PSCell List 0..<maxnoofPSCellsPerPrimaryCellinUEHistoryInfo>List of cells configured as PSCells. Most recent PSCell related information is added to the top of the list.YESignore
>Last Visited PSCell InformationM 9.3.1.235The PSCell related information.-
Range bound Explanation
maxnoofPSCellsPerPrimaryCellinUEHistoryInfoMaximum number of last visited PSCell information records that can be reported in the IE. Value is 8.
Up

9.3.1.98  Cell Typep. 255

This IE provides the cell coverage area.
IE/Group Name Pre­sence Range IE type and reference Semantics description
Cell SizeMENUMERATED (verysmall, small, medium, large, …)
Up

9.3.1.99  Associated QoS Flow Listp. 256

This IE indicates the list of QoS flows associated with e.g. a DRB or UP TNL endpoint.
IE/Group Name Pre­sence Range IE type and refe­rence Semantics description Criti­cality Assi­gned Criti­cality
Associated QoS Flow Item1..<maxnoofQoSFlows>-
>QoS Flow IdentifierM 9.3.1.51-
>QoS Flow Mapping IndicationOENUMERATED (ul, dl, …)-
>Current QoS Parameters Set Index OAlternative QoS Parameters Set Index
9.3.1.152
Index to the currently fulfilled alternative QoS parameters setYESignore
Range bound Explanation
maxnoofQoSFlowsMaximum no. of QoS flows allowed within one PDU session. Value is 64.
Up

9.3.1.100  Information on Recommended Cells and RAN Nodes for Pagingp. 256

This IE provides information on recommended cells and NG-RAN nodes for paging.
IE/Group Name Pre­sence Range IE type and reference Semantics description
Recommended Cells for PagingM 9.3.1.71
Recommended RAN Nodes for PagingM 9.3.1.101
Up

Up   Top   ToC