Tech-invite3GPPspaceIETFspace
21222324252627282931323334353637384‑5x

Content for  TS 38.413  Word version:  18.2.0

Top   Top   Up   Prev   Next
1…   4…   8…   8.2…   8.2.3…   8.3…   8.3.4…   8.4…   8.4.3…   8.5…   8.7…   8.8…   8.10…   8.12…   8.17…   9…   9.2…   9.2.2…   9.2.3…   9.2.4…   9.2.6…   9.2.7…   9.2.9…   9.2.11…   9.2.16…   9.2.17…   9.3…   9.3.1.21…   9.3.1.41…   9.3.1.61…   9.3.1.81…   9.3.1.101…   9.3.1.121…   9.3.1.141…   9.3.1.161…   9.3.1.181…   9.3.1.205…   9.3.1.222…   9.3.1.245…   9.3.2…   9.3.3…   9.3.3.21…   9.3.3.42…   9.3.4…   9.3.4.10…   9.3.5…   9.4…   9.4.4   9.4.5   9.4.6…   9.5…   10…

 

9.3.1.181  NR Frequency Info |R16|p. 288

This defines the carrier frequency and bands used in a cell for a given direction (UL or DL) in FDD or for both UL and DL directions in TDD.
IE/Group Name Pre­sence Range IE type and reference Semantics description
NR ARFCNMINTEGER (0.. maxNRARFCN)RF Reference Frequency as defined in clause 5.4.2.1 of TS 38.104. The frequency provided in this IE identifies the absolute frequency position of the reference resource block (Common RB 0) of the carrier. Its lowest subcarrier is also known as Point A.
NR Frequency Band List1This IE is not used in this specification and is ignored.
>NR Frequency Band Item1..<maxnoofNRCellBands>
>>NR Frequency BandMINTEGER (1.. 1024, ...)Primary NR Operating Band as defined in clause 5.4.2.3 of TS 38.104.
The value 1 corresponds to n1, value 2 corresponds to NR operating band n2, etc.
Range bound Explanation
maxNRARFCNMaximum value of NRARFCNs. Value is 3279165.
maxnoofNRCellBandsMaximum no. of frequency bands supported for a NR cell. Value is 32.
Up

9.3.1.182  Area Scope of Neighbour Cells |R16|p. 288

This IE defines the area scope of neighbour cells for logged MDT.
IE/Group Name Pre­sence Range IE type and reference Semantics description
Area Scope of Neighbour Cells ItemM1..<maxnoofFreqforMDT>
>NR Frequency InfoM 9.3.1.181
>PCI List for MDT0.. <maxnoofNeighPCIforMDT>
>>NR PCIMINTEGER (0..1007, …)NR Physical Cell ID
Range bound Explanation
maxnoofFreqforMDTMaximum no. of Frequency Information subject for MDT scope. Value is 8.
maxnoofNeighPCIforMDTMaximum no. of Neighbour cells subject for MDT scope. Value is 32.
Up

9.3.1.183  NPN Paging Assistance Information |R16|p. 288

This IE contains NPN Paging Assistance Information.
IE/Group Name Pre­sence Range IE type and reference Semantics description
CHOICE NPN Paging Assistance InformationM
>PNI-NPN Paging Assistance
>>PNI-NPN Paging AssistanceMAllowed PNI-NPN List
9.3.3.45
Up

9.3.1.184  NPN Mobility Information |R16|p. 289

This IE indicates the access restrictions related to an NPN.
IE/Group Name Pre­sence Range IE type and refe­rence Semantics description Criti­cality Assi­gned Criti­cality
CHOICE NPN Mobility InformationM-
>SNPN Mobility Information-
>>Serving NIDMNID
9.3.3.42
-
>>Equivalent SNPNs List0..1YESreject
>>>Equivalent SNPNs Item1..<maxnoofESNPNs>Allowed SNPNs in addition to Serving SNPN. This list corresponds to the list of "equivalent SNPNs" as defined in TS 24.501. This list is part of the roaming restriction information. Roaming restrictions apply to SNPNs other than the Serving SNPN and Equivalent SNPNs. -
>>>>PLMN IdentityM 9.3.3.5-
>>>>NIDM 9.3.3.42-
>PNI-NPN Mobility Information-
>>Allowed PNI-NPN ListM 9.3.3.45-
Up

9.3.1.185  Cell CAG Information |R16|p. 289

This IE provides information about support of closed access groups for a designated cell.
IE/Group Name Pre­sence Range IE type and reference Semantics description
NG-RAN CGI M 9.3.1.73
Cell CAG ListM 9.3.3.47
Up

9.3.1.186  Target to Source Failure Transparent Container |R16|p. 290

This IE is used to transparently pass radio related information from the handover target to the handover source through the core network in case of failure of the preparation at the target; it is produced by the target RAN node and is transmitted to the source RAN node.
IE/Group Name Pre­sence Range IE type and reference Semantics description
Target to Source Failure Transparent ContainerMOCTET STRINGThis IE includes a transparent container from the target RAN node to the source RAN node. The octets of the OCTET STRING are encoded according to the specifications of the target system.
Note:
In the current version of the specification, this IE may carry the Target NG-RAN Node to Source NG-RAN Node Failure Transparent Container IE.
Up

9.3.1.187  Target NG-RAN Node to Source NG-RAN Node Failure Transparent Container |R16|p. 290

This IE is produced by the target NG-RAN node and is transmitted to the source NG-RAN node in case of preparation failure.
This IE is transparent to the 5GC.
IE/Group Name Pre­sence Range IE type and refe­rence Semantics description Criti­cality Assi­gned Criti­cality
Cell CAG InformationO 9.3.1.185-
NGAP IE Support Information Response ListO 9.3.1.242YESignore
Up

9.3.1.188  DAPS Request Information |R16|p. 290

The DAPS Indicator IE indicates that the source NG-RAN node requests a DAPS Handover for the concerned DRB.
IE/Group Name Pre­sence Range IE type and reference Semantics description
DAPS IndicatorMENUMERATED (DAPS HO required, …)Indicates that DAPS Handover is requested
Up

9.3.1.189  DAPS Response Information |R16|p. 290

The DAPS Response Indicator IE indicates the per DRB response to a requested DAPS Handover.
IE/Group Name Pre­sence Range IE type and reference Semantics description
DAPS Response IndicatorMENUMERATED (DAPS HO accepted, DAPS HO not accepted, …)Indicates that DAPS Handover is accepted or not
Up

9.3.1.190  Early Status Transfer Transparent Container |R16|p. 291

The Early Status Transfer Transparent Container IE is an information element that is produced by the source NG-RAN node and is transmitted to the target NG-RAN node. This IE is used for the NG DAPS handover case, and for the NG-handover with time-based trigger condition case.
This IE is transparent to the 5GC.
IE/Group Name Pre­sence Range IE type and refe­rence Semantics description Criti­cality Assi­gned Criti­cality
CHOICE Procedure StageM-
>First DL COUNT
>>DRBs Subject To Early Status Transfer List1-
>>>DRBs Subject To Early Status Transfer Item1..<maxnoofDRBs>-
>>>>DRB IDM 9.3.1.53-
>>>>CHOICE First DL COUNTM-
>>>>>12 bits
>>>>>>FIRST DL COUNT ValueMCOUNT Value for PDCP SN Length 12
9.3.1.109
PDCP-SN and Hyper frame number of the first DL SDU that the source NG-RAN node forwards to the target NG-RAN node in case of 12 bit long PDCP-SN-
>>>>>18 bits
>>>>>>FIRST DL COUNT ValueMCOUNT Value for PDCP SN Length 18
9.3.1.110
PDCP-SN and Hyper frame number of the first DL SDU that the source NG-RAN node forwards to the target NG-RAN node in case of 18 bit long PDCP-SN-
>DL DiscardingYESignore
>>DRBs Subject To DL Discarding List1-
>>>DRBs Subject To DL Discarding Item1 .. <maxnoofDRBs>-
>>>>DRB IDM 9.3.1.53-
>>>>CHOICE DL DiscardingM-
>>>>>12 bits
>>>>>>DISCARD DL COUNT ValueMCOUNT Value for PDCP SN Length 12
9.3.1.109
PDCP-SN and Hyper frame number for which the receiving NG-RAN node should discard forwarded DL SDUs associated with lower values in case of 12 bit long PDCP-SN-
>>>>>18 bits
>>>>>>DISCARD DL COUNT ValueMCOUNT Value for PDCP SN Length 18
9.3.1.110
PDCP-SN and Hyper frame number for which the receiving NG-RAN node should discard forwarded DL SDUs associated with lower values in case of 18 bit long PDCP-SN-
Range bound Explanation
maxnoofDRBsMaximum no. of DRBs allowed towards one UE. Value is 32.
Up

9.3.1.191  Extended Slice Support List |R16|p. 292

This IE indicates a list of supported slices.
IE/Group Name Pre­sence Range IE type and reference Semantics description
Slice Support Item1..<maxnoofExtSliceItems>
>S-NSSAIM 9.3.1.24
Range bound Explanation
maxnoofExtSliceItemsMaximum no. of signalled slice support items. Value is 65535.
Up

9.3.1.192  UE Capability Info Request |R16|p. 292

This IE indicates the request to provide to the AMF the UE radio capability related information when retrieved from the UE.
IE/Group Name Pre­sence Range IE type and reference Semantics description
UE Capability Info RequestMENUMERATED (requested, …)
Up

9.3.1.193  Extended RAN Node Name |R16|p. 292

This IE provides extended human readable name of the NG-RAN node.
IE/Group Name Pre­sence Range IE type and reference Semantics description
RAN Node Name VisibleOVisibleString (SIZE(1..150, …))
RAN Node Name UTF8OUTF8String (SIZE(1..150, …))
Up

9.3.1.194  MICO All PLMN |R16|p. 292

This IE indicates that the UE is configured with MICO mode by the AMF for the "all PLMN" as specified in TS 23.501.
IE/Group Name Pre­sence Range IE type and reference Semantics description
MICO All PLMNMENUMERATED (true, …)
Up

9.3.1.195  Source Node ID |R16|p. 293

This IE identifies the source SN for the handover.
IE/Group Name Pre­sence Range IE type and reference Semantics description
CHOICE Source Node IDM
>Source E-UTRAN Node ID
>>Source en-gNB IDMGlobal gNB ID
9.3.1.6
This IE is used for handover from EN-DC to SA. The source en-gNB ID is the identity of the source SN.
Up

9.3.1.196  E-UTRAN Composite Available Capacity Group |R17|p. 293

This IE indicates the overall available resource level in the cell in downlink and uplink.
IE/Group Name Pre­sence Range IE type and reference Semantics description
Composite Available Capacity DownlinkME-UTRAN Composite Available Capacity
9.3.1.197
For the downlink
Composite Available Capacity UplinkME-UTRAN Composite Available Capacity
9.3.1.197
For the uplink
Up

9.3.1.197  E-UTRAN Composite Available Capacity |R17|p. 293

This IE indicates the overall available resource level in the cell in either downlink or uplink.
IE/Group Name Pre­sence Range IE type and reference Semantics description
E-UTRAN Cell Capacity Class ValueO 9.3.1.198
E-UTRAN Capacity Value M 9.3.1.199'0' indicates no resource is available, Measured on a linear scale.
Up

9.3.1.198  E-UTRAN Cell Capacity Class Value |R17|p. 293

This IE indicates the value that classifies the cell capacity with regards to the other cells. This IE only indicates resources that are configured for traffic purposes.
IE/Group Name Pre­sence Range IE type and reference Semantics description
Cell Capacity Class ValueMINTEGER (1..100, ...)Value 1 indicates the minimum cell capacity, and 100 indicates the maximum cell capacity. There should be a linear relation between cell capacity and Cell Capacity Class Value.
Up

9.3.1.199  E-UTRAN Capacity Value |R17|p. 293

This IE indicates the amount of resources that are available relative to the total E-UTRAN resources. The capacity value should be measured and reported so that the minimum E-UTRAN resource usage of existing services is reserved according to implementation. This IE can be weighted according to the ratio of cell capacity class values, if available.
IE/Group Name Pre­sence Range IE type and reference Semantics description
Capacity ValueMINTEGER (0..100)Value 0 indicates no available capacity, and 100 indicates maximum available capacity. Capacity Value should be measured on a linear scale.
Up

9.3.1.200  E-UTRAN Radio Resource Status |R17|p. 294

This IE indicates the usage of the PRBs for all traffic in downlink and uplink (TS 36.314, TS 23.203) and the usage of PDCCH CCEs for downlink and uplink scheduling.
IE/Group Name Pre­sence Range IE type and reference Semantics description
DL GBR PRB UsageMINTEGER (0..100)
UL GBR PRB UsageMINTEGER (0..100)
DL Non-GBR PRB UsageMINTEGER (0..100)
UL Non-GBR PRB UsageMINTEGER (0..100)
DL Total PRB UsageMINTEGER (0..100)
UL Total PRB UsageMINTEGER (0..100)
DL Scheduling PDCCH CCE UsageOINTEGER (0..100)
UL Scheduling PDCCH CCE UsageOINTEGER (0..100)
Up

9.3.1.201Void

9.3.1.202Void

9.3.1.203Void

9.3.1.204Void


Up   Top   ToC