Content for TS 36.117 Word version: 16.0.0
4 General test conditions and declarations
5 Operating bands and Channel arrangement
6 Transmitter characteristics
7 Receiver characteristics
8 Access Performance requirement
9 Backhaul Performance requirement
A Propagation models for relay demodulation requirements
B Reference Measurement Channel
C Physical Channel Set-up for conformance tests
$ Change History
4 General test conditions and declarations Word‑p. 10
4.1 Measurement uncertainties and Test Requirements Word‑p. 11
4.2 Relay classes
4.3 Regional requirements
4.4 Selection of configurations for testing Word‑p. 12
4.5 Manufacturer's declarations of regional and optional requirements
4.6 Specified frequency range and supported channel bandwidth
4.7 Format and interpretation of tests
5 Operating bands and Channel arrangement Word‑p. 13
6 Transmitter characteristics
6.1 General
6.2 Output power Word‑p. 14
6.2.1 Definition and applicability
6.2.2 Minimum Requirement
6.2.3 Test purpose Word‑p. 15
6.2.4 Method of test
6.2.5 Test Requirements
6.2.6 Configured transmitted Power for backhaul link Word‑p. 16
6.3 Output power dynamics
6.3.1 Access Link Test Requirements.
6.3.1.1 RE Power control dynamic range
6.3.1.2 Total power dynamic range
6.3.1.3 Transmitter OFF power
6.3.1.4 Transmitter transient period
6.3.2 Backhaul Link Test Requirements
6.3.2.1 Minimum Output Power
6.3.2.1.1 Test purpose
6.3.2.1.2 Test applicability
6.3.2.1.3 Minimum conformance requirements Word‑p. 17
6.3.2.1.4 Test description
6.3.2.1.5 Test Requirement
6.3.2.2 Power Control Absolute power tolerance
6.3.2.3 Power Control Relative power tolerance
6.3.2.4 Aggregate power control tolerance Word‑p. 18
6.3.2.5 Power Control for UL-MIMO
6.3.2.6 Transmit ON/OFF Time Mask
6.3.2.7 Transmit OFF Power
6.4 Transmitted signal quality Word‑p. 19
6.4.1 Frequency error
6.4.1.1 Definition and applicability
6.4.1.2 Minimum Requirement
6.4.1.3 Test purpose
6.4.1.4 Method of test
6.4.1.5 Test requirement
6.4.2 EVM
6.4.3 Time alignment error
6.4.4 DL RS power Word‑p. 20
6.5 Unwanted emissions
6.5.1 Transmitter spurious emissions
6.5.2 Adjacent Channel Leakage power Ratio (ACLR)
6.5.3 Operating Bands Unwanted Emissions
6.6 Transmitter intermodulation Word‑p. 24
7 Receiver characteristics
7.1 General
7.2 Reference sensitivity level
7.3 Dynamic range
7.4 In-channel selectivity
7.5 Adjacent Channel Selectivity (ACS)
7.5.1 Backhaul Adjacent Channel Selectivity (ACS)
7.5.2 Access Link Adjacent Channel Selectivity (ACS) Word‑p. 26
7.6 Blocking characteristics
7.6.1 Backhaul Blocking Characteristics
7.6.2 Access Link Blocking Characteristics
7.6.3 Blocking requirements for co-location
7.7 Receiver spurious emissions
7.8 Receiver intermodulation
8 Access Performance requirement
8.1 General
8.2 Performance requirements for PUSCH
8.2.1 Requirements in multipath fading propagation conditions
8.2.2 Requirements for UL timing adjustment
8.2.3 Requirements for HARQ-ACK multiplexed on PUSCH Word‑p. 28
8.3 Performance requirements for PUCCH
8.3.1 ACK missed detection requirements for single user PUCCH format 1a
8.3.2 CQI missed detection requirements for PUCCH format2
8.3.3 ACK missed detection requirements for multi user PUCCH format 1a
8.4 Performance requirements for PRACH
9 Backhaul Performance requirement Word‑p. 29
9.1 General
9.2 Demodulation of PDSCH (Cell-Specific Reference Symbols)
9.3 Demodulation of PDSCH (User-Specific Reference Symbols)
9.4 Demodulation of PDCCH/PCFICH
9.5 Demodulation of PHICH
9.6 Demodulation of PBCH
9.7 Sustained downlink data rate provided by lower layers
9.8 Demodulation of R-PDCCH Word‑p. 30
9.8.1 FDD
9.8.1.1 FDD R-PDCCH performance based on UE-specific reference signals transmitted on antenna port 7 with 1x2 antenna configuration
9.8.1.1.1 Test purpose
9.8.1.1.2 Test applicability
9.8.1.1.3 Minimum conformance requirements
9.8.1.1.4 Test description Word‑p. 31
9.8.1.1.5 Test requirement Word‑p. 34
9.8.1.2 FDD R-PDCCH performance based on UE-specific reference signals transmitted on antenna port 7 with 4x2 antenna configuration Word‑p. 35
9.8.2 TDD
9.8.2.1 TDD R-PDCCH performance based on UE-specific reference signals transmitted on antenna port 7 with 1x2 antenna configuration
9.8.2.1.1 Test purpose
9.8.2.1.2 Test applicability
9.8.2.1.3 Minimum conformance requirements
9.8.2.1.4 Test description Word‑p. 41
9.8.2.1.5 Test requirement Word‑p. 44
9.8.2.2 TDD R-PDCCH performance based on UE-specific reference signals transmitted on antenna port 7 with 4x2 antenna configuration Word‑p. 45
A (Normative) Propagation models for relay demodulation requirements Word‑p. 51
A.1 Propagation models for backhaul link
A.2 multipath propagation fading conditions for access link Word‑p. 53
B (Normative) Reference Measurement Channel Word‑p. 55
B.1 Reference measurement channels for R-PDCCH performance requirements
B.2 OCNG patterns for R-PDCCH performance requirements
C (Normative) Physical Channel Set-up for conformance tests Word‑p. 58
$ Change History Word‑p. 60
