TS 45.056
RAN6
★
GSM Cordless Telephony System (CTS), Phase 1 –
CTS-FP Radio Subsystem
use "3GPP‑Page" to get the Word version
use "ETSI‑search" to get the PDF version
for a better overview, the Table of Contents (ToC) is reproduced
use "ETSI‑search" to get the PDF version
for a better overview, the Table of Contents (ToC) is reproduced
V15.0.0 (PDF)
2018/06 31 p.
V14.0.0
2017/03 31 p.
V13.0.0
2015/12 31 p.
V12.0.0
2014/09 31 p.
V11.0.0
2012/09 31 p.
V10.0.0
2011/04 31 p.
V9.0.0
2009/12 31 p.
V8.0.0
2008/12 31 p.
V7.0.0
2007/10 31 p.
V6.0.0
2005/02 31 p.
V5.0.0
2002/07 31 p.
V4.0.0
2001/04 31 p.
GSM Rel-99 v8.0.1
2000/10 30 p.
GSM Rel-98 v7.1.1
2000/09 30 p.
Rapporteur: Mr. Usai, Paolino
This TS specifies the requirements for the CTS-Fixed Part (CTS-FP) transceiver of the digital mobile cellular and personal communication systems operating in the 900 MHz (P-GSM and E-GSM) and 1800 MHz band (GSM 900 and DCS 1800), and specifies the Radio subsystem frequency control implemented in the CTS-Fixed Part.
full Table of Contents for TS 45.056 Word version: 15.0.0
1 Scope
2 References
3 Definitions and abbreviations
4 Radio transmission and reception
5 Radio subsystem frequency control
A Spectrum characteristics (spectrum due to the modulation)
B [N] Transmitted power level versus time
C [N] Environmental conditions
D Change history
1 Scope Word-p. 6
2 References
3 Definitions and abbreviations Word-p. 7
4 Radio transmission and reception
4.1 Frequency band and channels arrangements
4.2 Reference configuration Word-p. 8
4.3 Transmitter characteristics
5 Radio subsystem frequency control Word-p. 21
4.3.1 Output power
4.3.2 Output RF spectrum Word-p. 9
4.4 Receiver characteristics
4.3.2.1 Spectrum due to the modulation and wide band noise
4.3.2.2 Spectrum due to switching transient Word-p. 10
4.3.3 Spurious emission Word-p. 11
4.3.4 Radio frequency tolerance Word-p. 12
4.3.5 Output level dynamic operation
4.3.6 Phase accuracy
4.3.7 Intermodulation attenuation
4.4.1 Blocking characteristics Word-p. 13
4.4.2 AM suppression characteristics Word-p. 14
4.4.3 Intermodulation characteristics
4.5 Transmitter / receiver performance Word-p. 15
5.1 Void
5.2 General
5.3 Adaptive Frequency Allocation (AFA)
5.4 TFH carrier list selection
A Spectrum characteristics (spectrum due to the modulation) Word-p. 25
B (Normative) Transmitted power level versus time Word-p. 27
C (Normative) Environmental conditions Word-p. 28
D Change history Word-p. 29
5.4.1 Acceptance procedure
5.4.3 AFA and TFH selection performance requirements
5.5 CTS Beacon channel carrier selection Word-p. 23
5.6 Timeslot assignment for dedicated connection
5.7 Frequency control parameters
5.4.1.1 Basic threshold
5.4.1.2 Sliding window technique Word-p. 22
5.4.1.3 Fixed window technique
5.4.1.4 List extension check
5.4.2 Parameters
5.4.3 AFA and TFH selection performance requirements
