TS 36.521-3
E-UTRA — UE Conformance Specification
Radio Transmission and Reception
Part 3: Radio Resource Management (RRM) Conformance Testing

3GPP‑Page ETSI‑search

V18.10.0 (PDF) 2025/09 4790 p.

V17.2.0 2024/06 79 p.

V16.15.0 2022/12 80 p.

V15.6.0 2020/03 71 p.

V14.5.0 2018/09 62 p.

V13.2.0 2017/03 54 p.

V12.12.0 2017/03 51 p.

V11.4.0 2014/03 32 p.

V10.5.0 2016/09 29 p.

V9.10.0 2012/09 25 p.

V8.4.0 2010/06 15 p.

Rapporteur:: Mr. Vora, Mayur
Qualcomm UK Ltd

full Table of Contents for TS 36.521-3 Word version: 18.10.0

Scope p. 134

References p. 134

Definition of terms, symbols and abbreviations p. 135

3.1

Terms p. 135

3.2

Symbols p. 137

3.3

Abbreviations p. 138

3.4

Void p. …

3.5

Additional notation p. 141

3.5.1	Groups of bands p. 141
3.5.1A	Groups of bands for satellite access p. 143

Requirements for support of RRM p. 144

3A.1

General p. 144

3A.2

Requirements Classification for Statistical Testing p. 144

3A.3

RRM Test Configurations p. 144

3A.3.1	UE with Single or Multiple Antenna Connector p. 144
3A.3.2	Test configuration for Inter band test cases p. 145
3A.3.3	Test configuration for Inter RAT test cases p. 145
3A.3.4	UE with Multiband Capability p. 145
3A.3.5	E-UTRAN operating band configuration p. 145
3A.3.6	CA configuration p. 146
3A.3.7	HD-FDD category 0 testing p. 146
3A.3.8	Test configuration for satellite access p. 146

3A.4

Antenna Configuration p. 146

3A.4.1

Antenna connection for 4 Rx capable UEs p. 147

3A.4.1.1

Introduction p. 147

3A.4.1.2

Principle of testing p. 147

3A.4.1.2.1	Single carrier tests p. 147
3A.4.1.2.2	Carrier aggregation and Dual connectivity tests p. 148
3A.4.1.2.3	Antenna connection for bands where 2RX is supported p. 149
3A.4.1.2.4	Antenna connection for bands where 4RX is supported p. 149

3A.5

Test Cases for Synchronous and Asynchronous Dual Connectivity p. 149

3A.5.1	Introduction p. 149
3A.5.2	Principle of Testing p. 149

3A.6

Test cases for Carrier Aggregation under operation with Frame Structure 3 Test Cases with Different Duplex Modes p. 149

3A.6.1	Introduction p. 149
3A.6.2	Principle of testing p. 149

3A.7

Test case selection criteria for RRM Carrier Aggregation p. 149

3A.7.1	Introduction p. 149
3A.7.2	Principle of testing p. 150

E-UTRAN RRC_IDLE State Mobility p. 151

4.0

- p. 151

4.1

E-UTRAN Cell Selection p. 151

4.2

E-UTRAN Cell Re-Selection p. 151

4.2.1

E-UTRAN FDD - FDD cell re-selection intra frequency case p. 151

4.2.1.1

Test purpose p. 151

4.2.1.2

Test applicability p. 151

4.2.1.3

Minimum conformance requirements p. 151

4.2.1.4

Test description p. 152

4.2.1.4.1	Initial conditions p. 152
4.2.1.4.2	Test procedure p. 153
4.2.1.4.3	Message contents p. 154

4.2.1.5

Test requirement p. 154

4.2.2

E-UTRAN TDD - TDD cell re-selection intra frequency case p. 156

4.2.2.1

Test purpose p. 156

4.2.2.2

Test applicability p. 156

4.2.2.3

Minimum conformance requirements p. 156

4.2.2.4

Test description p. 156

4.2.2.4.1	Initial conditions p. 156
4.2.2.4.2	Test procedure p. 157
4.2.2.4.3	Message contents p. 158

4.2.2.5

Test requirement p. 158

4.2.3

E-UTRAN FDD - FDD cell re-selection inter frequency case p. 160

4.2.3.1

Test purpose p. 160

4.2.3.2

Test applicability p. 160

4.2.3.3

Minimum conformance requirements p. 160

4.2.3.4

Test description p. 161

4.2.3.4.1	Initial conditions p. 161
4.2.3.4.2	Test procedure p. 162
4.2.3.4.3	Message contents p. 163

4.2.3.5

Test requirement p. 163

4.2.4

E-UTRAN FDD - TDD cell re-selection inter frequency case p. 165

4.2.4.1

Test purpose p. 165

4.2.4.2

Test applicability p. 165

4.2.4.3

Minimum conformance requirements p. 165

4.2.4.4

Test description p. 166

4.2.4.4.1	Initial conditions p. 166
4.2.4.4.2	Test procedure p. 167
4.2.4.4.3	Message contents p. 168

4.2.4.5

Test requirement p. 168

4.2.5

E-UTRAN TDD - FDD cell re-selection inter frequency case p. 171

4.2.5.1

Test purpose p. 171

4.2.5.2

Test applicability p. 171

4.2.5.3

Minimum conformance requirements p. 171

4.2.5.4

Test description p. 172

4.2.5.4.1	Initial conditions p. 172
4.2.5.4.2	Test procedure p. 173
4.2.5.4.3	Message contents p. 174

4.2.5.5

Test requirement p. 174

4.2.6

E-UTRAN TDD - TDD cell re-selection inter frequency case p. 177

4.2.6.1

Test purpose p. 177

4.2.6.2

Test applicability p. 177

4.2.6.3

Minimum conformance requirements p. 177

4.2.6.4

Test description p. 178

4.2.6.4.1	Initial conditions p. 178
4.2.6.4.2	Test procedure p. 179
4.2.6.4.3	Message contents p. 180

4.2.6.5

Test requirement p. 180

4.2.7

E-UTRAN FDD - FDD Inter frequency case in the existence of non-allowed CSG cell p. 183

4.2.7.1

Test purpose p. 183

4.2.7.2

Test applicability p. 183

4.2.7.3

Minimum conformance requirements p. 183

4.2.7.4

Test description p. 184

4.2.7.4.1	Initial conditions p. 184
4.2.7.4.2	Test procedure p. 185
4.2.7.4.3	Message contents p. 186

4.2.7.5

Test requirement p. 188

4.2.8

E-UTRAN TDD - TDD Inter frequency case in the existence of non-allowed CSG cell p. 190

4.2.8.1

Test purpose p. 190

4.2.8.2

Test applicability p. 190

4.2.8.3

Minimum conformance requirements p. 190

4.2.8.4

Test description p. 191

4.2.8.4.1	Initial conditions p. 191
4.2.8.4.2	Test procedure p. 192
4.2.8.4.3	Message contents p. 193

4.2.8.5

Test requirement p. 195

4.2.9

E-UTRAN FDD - FDD intra frequency cell re-selection case for 5MHz bandwidth p. 197

4.2.9.1

Test purpose p. 197

4.2.9.2

Test applicability p. 197

4.2.9.3

Minimum conformance requirements p. 197

4.2.9.4

Test description p. 197

4.2.9.4.1	Initial conditions p. 197
4.2.9.4.2	Test procedure p. 197
4.2.9.4.3	Message contents p. 197

4.2.9.5

Test requirement p. 197

4.2.10

E-UTRAN FDD - FDD reselection using an increased number of carriers p. 198

4.2.10.1

Test purpose p. 198

4.2.10.2

Test applicability p. 198

4.2.10.3

Minimum conformance requirements p. 198

4.2.10.4

Test description p. 200

4.2.10.4.1	Initial conditions p. 200
4.2.10.4.2	Test procedure p. 202
4.2.10.4.3	Message contents p. 203

4.2.10.5

Test requirement p. 203

4.2.11

E-UTRAN TDD - TDD reselection using an increased number of carriers p. 205

4.2.11.1

Test purpose p. 205

4.2.11.2

Test applicability p. 205

4.2.11.3

Minimum conformance requirements p. 205

4.2.11.4

Test description p. 205

4.2.11.4.1	Initial conditions p. 205
4.2.11.4.2	Test procedure p. 207
4.2.11.4.3	Message contents p. 208

4.2.11.5

Test requirement p. 208

4.2.12

E-UTRAN FDD - FDD Intra frequency case for CE UE in normal coverage p. 210

4.2.12.1

Test purpose p. 210

4.2.12.2

Test applicability p. 210

4.2.12.3

Minimum conformance requirements p. 210

4.2.12.4

Test description p. 211

4.2.12.4.1	Initial conditions p. 211
4.2.12.4.2	Test procedure p. 212
4.2.12.4.3	Message contents p. 213

4.2.12.5

Test requirement p. 213

4.2.13

E-UTRAN HD - FDD Intra frequency case for CE UE in normal coverage p. 215

4.2.13.1

Test purpose p. 215

4.2.13.2

Test applicability p. 215

4.2.13.3

Minimum conformance requirements p. 215

4.2.13.4

Test description p. 215

4.2.13.4.1	Initial conditions p. 215
4.2.13.4.2	Test procedure p. 216
4.2.13.4.3	Message contents p. 216

4.2.13.5

Test requirement p. 216

4.2.14

E-UTRAN TDD - TDD Intra frequency case for CE UE in normal coverage p. 218

4.2.14.1

Test purpose p. 218

4.2.14.2

Test applicability p. 218

4.2.14.3

Minimum conformance requirements p. 218

4.2.14.4

Test description p. 218

4.2.14.4.1	Initial conditions p. 218
4.2.14.4.2	Test procedure p. 219
4.2.14.4.3	Message contents p. 219

4.2.14.5

Test requirement p. 219

4.2.15

E-UTRAN FDD - FDD Intra frequency case for CE UE in enhanced coverage p. 221

4.2.15.1

Test purpose p. 221

4.2.15.2

Test applicability p. 221

4.2.15.3

Minimum conformance requirements p. 221

4.2.15.4

Test description p. 222

4.2.15.4.1	Initial conditions p. 222
4.2.15.4.2	Test procedure p. 223
4.2.15.4.3	Message contents p. 224

4.2.15.5

Test requirement p. 224

4.2.16

E-UTRAN HD - FDD Intra frequency case for CE UE in enhanced coverage p. 226

4.2.16.1

Test purpose p. 226

4.2.16.2

Test applicability p. 226

4.2.16.3

Minimum conformance requirements p. 226

4.2.16.4

Test description p. 226

4.2.16.4.1	Initial conditions p. 226
4.2.16.4.2	Test procedure p. 227
4.2.16.4.3	Message contents p. 227

4.2.16.5

Test requirement p. 227

4.2.17

E-UTRAN TDD - TDD Intra frequency case for CE UE in enhanced coverage p. 229

4.2.17.1

Test purpose p. 229

4.2.17.2

Test applicability p. 229

4.2.17.3

Minimum conformance requirements p. 229

4.2.17.4

Test description p. 229

4.2.17.4.1	Initial conditions p. 229
4.2.17.4.2	Test procedure p. 230
4.2.17.4.3	Message contents p. 230

4.2.17.5

Test requirement p. 230

4.2.18

HD-FDD Intra frequency cell reselection for Category NB1 UE in In-Band Mode under Normal Coverage p. 232

4.2.18.1

Test purpose p. 232

4.2.18.2

Test applicability p. 232

4.2.18.3

Minimum conformance requirements p. 232

4.2.18.4

Test description p. 233

4.2.18.4.1	Initial conditions p. 233
4.2.18.4.2	Test procedure p. 233
4.2.18.4.3	Message contents p. 234

4.2.18.5

Test requirement p. 235

4.2.19

HD - FDD Intra frequency case for UE Category NB1 In-Band mode in enhanced coverage p. 237

4.2.19.1

Test purpose p. 237

4.2.19.2

Test applicability p. 237

4.2.19.3

Minimum conformance requirements p. 237

4.2.19.4

Test description p. 238

4.2.19.4.1	Initial conditions p. 238
4.2.19.4.2	Test procedure p. 238
4.2.19.4.3	Message contents p. 239

4.2.19.5

Test requirement p. 239

4.2.20

E-UTRAN FDD - FDD Intra frequency case for UE Category 1bis p. 241

4.2.20.1

Test purpose p. 241

4.2.20.2

Test applicability p. 241

4.2.20.3

Minimum conformance requirements p. 241

4.2.20.4

Test description p. 242

4.2.20.4.1	Initial conditions p. 242
4.2.20.4.2	Test procedure p. 243
4.2.20.4.3	Message contents p. 244

4.2.20.5

Test requirement p. 244

4.2.21

E-UTRAN TDD - TDD Intra frequency case for UE Category 1bis p. 246

4.2.21.1

Test purpose p. 246

4.2.21.2

Test applicability p. 246

4.2.21.3

Minimum conformance requirements p. 246

4.2.21.4

Test description p. 246

4.2.21.4.1	Initial conditions p. 246
4.2.21.4.2	Test procedure p. 247
4.2.21.4.3	Message contents p. 247

4.2.21.5

Test requirement p. 247

4.2.22

E-UTRAN FDD - FDD cell re-selection intra frequency case for UE configured with highSpeedEnhancedMeasFlag p. 249

4.2.22.1

Test purpose p. 249

4.2.22.2

Test applicability p. 249

4.2.22.3

Minimum conformance requirements p. 249

4.2.22.4

Test description p. 250

4.2.22.4.1	Initial conditions p. 250
4.2.22.4.2	Test procedure p. 251
4.2.22.4.3	Message contents p. 252

4.2.22.5

Test requirement p. 252

4.2.23

E-UTRAN TDD - TDD cell re-selection intra frequency case for UE configured with highSpeedEnhancedMeasFlag p. 254

4.2.23.1

Test purpose p. 254

4.2.23.2

Test applicability p. 254

4.2.23.3

Minimum conformance requirements p. 254

4.2.23.4

Test description p. 255

4.2.23.4.1	Initial conditions p. 255
4.2.23.4.2	Test procedure p. 256
4.2.23.4.3	Message contents p. 257

4.2.23.5

Test requirement p. 257

4.2.24

HD - FDD Inter frequency case for UE Category NB1 In-Band mode in enhanced coverage p. 259

4.2.24.1

Test purpose p. 259

4.2.24.2

Test applicability p. 259

4.2.24.3

Minimum conformance requirements p. 259

4.2.24.4

Test description p. 260

4.2.24.4.1	Initial conditions p. 260
4.2.24.4.2	Test procedure p. 261
4.2.24.4.3	Message contents p. 262

4.2.24.5

Test requirement p. 262

4.2.25

E-UTRAN FDD - FDD Inter frequency case for CE UE in normal coverage p. 263

4.2.25.1

Test purpose p. 263

4.2.25.2

Test applicability p. 264

4.2.25.3

Minimum conformance requirements p. 264

4.2.25.4

Test description p. 265

4.2.25.4.1	Initial conditions p. 265
4.2.25.4.2	Test procedure p. 266
4.2.25.4.3	Message contents p. 266

4.2.25.5

Test requirement p. 266

4.2.26

E-UTRAN HD - FDD Inter frequency case for CE UE in normal coverage p. 268

4.2.26.1

Test purpose p. 268

4.2.26.2

Test applicability p. 268

4.2.26.3

Minimum conformance requirements p. 268

4.2.26.4

Test description p. 268

4.2.26.4.1	Initial conditions p. 268
4.2.26.4.2	Test procedure p. 269
4.2.26.4.3	Message contents p. 269

4.2.26.5

Test requirement p. 269

4.2.27

E-UTRAN TDD - TDD Inter frequency case for CE UE in normal coverage p. 271

4.2.27.1

Test purpose p. 271

4.2.27.2

Test applicability p. 271

4.2.27.3

Minimum conformance requirements p. 271

4.2.27.4

Test description p. 271

4.2.27.4.1	Initial conditions p. 271
4.2.27.4.2	Test procedure p. 272
4.2.27.4.3	Message contents p. 272

4.2.27.5

Test requirement p. 272

4.2.28

E-UTRAN FDD - FDD Inter frequency case for CE UE in enhanced coverage p. 274

4.2.28.1

Test purpose p. 274

4.2.28.2

Test applicability p. 274

4.2.28.3

Minimum conformance requirements p. 274

4.2.28.4

Test description p. 275

4.2.28.4.1	Initial conditions p. 275
4.2.28.4.2	Test procedure p. 276
4.2.28.4.3	Message contents p. 277

4.2.28.5

Test requirement p. 277

4.2.29

E-UTRAN HD - FDD Inter frequency case for CE UE in enhanced coverage p. 279

4.2.29.1

Test purpose p. 279

4.2.29.2

Test applicability p. 279

4.2.29.3

Minimum conformance requirements p. 279

4.2.29.4

Test description p. 279

4.2.29.4.1	Initial conditions p. 279
4.2.29.4.2	Test procedure p. 280
4.2.29.4.3	Message contents p. 280

4.2.29.5

Test requirement p. 280

4.2.30

E-UTRAN TDD Inter frequency case for CE UE in enhanced coverage p. 281

4.2.30.1

Test purpose p. 281

4.2.30.2

Test applicability p. 281

4.2.30.3

Minimum conformance requirements p. 281

4.2.30.4

Test description p. 281

4.2.30.4.1	Initial conditions p. 281
4.2.30.4.2	Test procedure p. 282
4.2.30.4.3	Message contents p. 282

4.2.30.5

Test requirement p. 282

4.2.31

E-UTRAN FDD - FDD Inter frequency case for UE Category 1bis p. 284

4.2.31.1

Test purpose p. 284

4.2.31.2

Test applicability p. 284

4.2.31.3

Minimum conformance requirements p. 284

4.2.31.4

Test description p. 285

4.2.31.4.1	Initial conditions p. 285
4.2.31.4.2	Test procedure p. 285
4.2.31.4.3	Message contents p. 285

4.2.31.5

Test requirement p. 285

4.2.32

E-UTRAN FDD - TDD Inter frequency case for UE Category 1bis p. 288

4.2.32.1

Test purpose p. 288

4.2.32.2

Test applicability p. 288

4.2.32.3

Minimum conformance requirements p. 288

4.2.32.4

Test description p. 288

4.2.32.4.1	Initial conditions p. 288
4.2.32.4.2	Test procedure p. 288
4.2.32.4.3	Message contents p. 288

4.2.32.5

Test requirement p. 288

4.2.33

E-UTRAN TDD - FDD Inter frequency case for UE Category 1bis p. 291

4.2.33.1

Test purpose p. 291

4.2.33.2

Test applicability p. 291

4.2.33.3

Minimum conformance requirements p. 291

4.2.33.4

Test description p. 291

4.2.33.4.1	Initial conditions p. 291
4.2.33.4.2	Test procedure p. 291
4.2.33.4.3	Message contents p. 291

4.2.33.5

Test requirement p. 291

4.2.34

E-UTRAN TDD - TDD Inter frequency case for UE Category 1bis p. 294

4.2.34.1

Test purpose p. 294

4.2.34.2

Test applicability p. 294

4.2.34.3

Minimum conformance requirements p. 294

4.2.34.4

Test description p. 294

4.2.34.4.1	Initial conditions p. 294
4.2.34.4.2	Test procedure p. 294
4.2.34.4.3	Message contents p. 294

4.2.34.5

Test requirement p. 294

4.2.35

E-UTRAN TDD - TDD Intra frequency case for UE Category NB1 In-Band mode in normal coverage p. 297

4.2.35.1

Test purpose p. 297

4.2.35.2

Test applicability p. 297

4.2.35.3

Minimum conformance requirements p. 297

4.2.35.4

Test description p. 298

4.2.35.4.1	Initial conditions p. 298
4.2.35.4.2	Test procedure p. 299
4.2.35.4.3	Message contents p. 299

4.2.35.5

Test requirement p. 299

4.2.36

E-UTRAN TDD - TDD Intra frequency case for UE Category NB1 In-Band mode in enhanced coverage p. 302

4.2.36.1

Test purpose p. 302

4.2.36.2

Test applicability p. 302

4.2.36.3

Minimum conformance requirements p. 302

4.2.36.4

Test description p. 304

4.2.36.4.1	Initial conditions p. 304
4.2.36.4.2	Test procedure p. 304
4.2.36.4.3	Message contents p. 305

4.2.36.5

Test requirement p. 305

4.2.37

E-UTRAN TDD - TDD Inter frequency case for UE Category NB1 In-Band mode in enhanced coverage p. 307

4.2.37.1

Test purpose p. 307

4.2.37.2

Test applicability p. 307

4.2.37.3

Minimum conformance requirements p. 307

4.2.37.4

Test description p. 308

4.2.37.4.1	Initial conditions p. 308
4.2.37.4.2	Test procedure p. 309
4.2.37.4.3	Message contents p. 309

4.2.37.5

Test requirement p. 309

4.2.38

HD - FDD Intra frequency case for UE Category NB1 In-Band mode in normal coverage with serving cell RRM measurement relaxation p. 312

4.2.38.1

Test purpose p. 312

4.2.38.2

Test applicability p. 312

4.2.38.3

Minimum conformance requirements p. 312

4.2.38.4

Test description p. 313

4.2.38.4.1	Initial conditions p. 313
4.2.38.4.2	Test procedure p. 314
4.2.38.4.3	Message contents p. 315

4.2.38.5

Test requirement p. 316

4.3

E-UTRAN to UTRAN Cell Re-Selection p. 319

4.3.1

E-UTRAN FDD - UTRAN FDD cell re-selection p. 319

4.3.1.1

E-UTRA FDD - UTRAN FDD cell reselection: UTRA FDD is of higher priority p. 319

4.3.1.1.1	Test purpose p. 319
4.3.1.1.2	Test applicability p. 319
4.3.1.1.3	Minimum conformance requirements p. 319
4.3.1.1.4	Test description p. 320
4.3.1.1.5	Test requirement p. 322

4.3.1.2

E-UTRAN FDD - UTRAN FDD cell re-selection: UTRA FDD is of lower priority p. 324

4.3.1.2.1	Test purpose p. 324
4.3.1.2.2	Test applicability p. 324
4.3.1.2.3	Minimum conformance requirements p. 325
4.3.1.2.4	Test description p. 325
4.3.1.2.5	Test requirement p. 327

4.3.1.3

E-UTRAN FDD - UTRAN FDD cell re-selection in fading propagation conditions: UTRA FDD is of lower priority p. 329

4.3.1.3.1	Test purpose p. 329
4.3.1.3.2	Test applicability p. 329
4.3.1.3.3	Minimum conformance requirements p. 330
4.3.1.3.4	Test description p. 330
4.3.1.3.5	Test requirement p. 333

4.3.1.4

E-UTRAN FDD - UTRAN FDD cell re-selection: UTRA FDD is of lower priority for 5MHz bandwidth p. 337

4.3.1.4.1	Test purpose p. 337
4.3.1.4.2	Test applicability p. 337
4.3.1.4.3	Minimum conformance requirements p. 338
4.3.1.4.4	Test description p. 338
4.3.1.4.5	Test requirement p. 339

4.3.1.5

Idle mode FDD to UTRA FDD interRAT reselection p. 339

4.3.1.5.1	Test purpose p. 339
4.3.1.5.2	Test applicability p. 339
4.3.1.5.3	Minimum conformance requirements p. 339
4.3.1.5.4	Test description p. 341
4.3.1.5.5	Test requirement p. 346

4.3.2

E-UTRAN FDD - UTRAN TDD cell re-selection p. 349

4.3.2.1

Test purpose p. 349

4.3.2.2

Test applicability p. 349

4.3.2.3

Minimum conformance requirements p. 349

4.3.2.3.1	3.84Mcps TDD option p. 349
4.3.2.3.2	1.28Mcps TDD option p. 349
4.3.2.3.3	7.68Mcps TDD option p. 349

4.3.2.4

Test description p. 350

4.3.2.4.1	3.84Mcps TDD option p. 350
4.3.2.4.2	1.28Mcps TDD option p. 350
4.3.2.4.3	7.68 Mcps TDD option p. 352

4.3.2.5

Test requirement p. 352

4.3.2.5.1	3.84Mcps TDD option p. 352
4.3.2.5.2	1.28Mcps TDD option p. 352
4.3.2.5.3	7.68 Mcps TDD option p. 354

4.3.2A

E-UTRA FDD to UTRA TDD cell re-selection for IncMon p. 354

4.3.2A.1

Test purpose p. 354

4.3.2A.2

Test applicability p. 354

4.3.2A.3

Minimum conformance requirements p. 354

4.3.2A.4

Test description p. 356

4.3.2A.4.1	Initial conditions p. 356
4.3.2A.4.2	Test procedure p. 357
4.3.2A.4.3	Message contents p. 358

4.3.2A.5

Test requirement p. 360

4.3.3

E-UTRAN TDD - UTRAN FDD cell re-selection p. 362

4.3.3.1

Test purpose p. 362

4.3.3.2

Test applicability p. 362

4.3.3.3

Minimum conformance requirements p. 362

4.3.3.4

Test description p. 363

4.3.3.4.1	Initial conditions p. 363
4.3.3.4.2	Test procedure p. 364
4.3.3.4.3	Message contents p. 364

4.3.3.5

Test requirement p. 365

4.3.3A

Idle mode TDD to UTRA FDD interRAT reselection p. 367

4.3.3A.1

Test purpose p. 367

4.3.3A.2

Test applicability p. 367

4.3.3A.3

Minimum conformance requirements p. 367

4.3.3A.4

Test description p. 368

4.3.3A.4.1	Initial conditions p. 368
4.3.3A.4.2	Test procedure p. 370
4.3.3A.4.3	Message contents p. 371

4.3.3A.5

Test requirement p. 372

4.3.4

E-UTRAN TDD - UTRAN TDD cell re-selection p. 375

4.3.4.1

E-UTRA TDD - UTRAN TDD cell re-selection: UTRA is of higher priority p. 375

4.3.4.1.1	Test purpose p. 375
4.3.4.1.2	Test applicability p. 375
4.3.4.1.3	Minimum conformance requirements p. 375
4.3.4.1.4	Test description p. 375
4.3.4.1.5	Test requirement p. 378

4.3.4.2

E-UTRAN TDD - UTRAN TDD cell re-selection: UTRA is of lower priority p. 380

4.3.4.2.1	Test purpose p. 380
4.3.4.2.2	Test applicability p. 380
4.3.4.2.3	Minimum conformance requirements p. 381
4.3.4.2.4	Test description p. 381
4.3.4.2.5	Test requirement p. 384

4.3.4.3

EUTRA TDD-UTRA TDD cell reselection in fading propagation conditions: UTRA TDD is of lower priority p. 385

4.3.4.3.1	Test purpose p. 385
4.3.4.3.2	Test applicability p. 385
4.3.4.3.3	Minimum conformance requirements p. 386
4.3.4.3.4	Test description p. 386
4.3.4.3.5	Test requirement p. 389

4.3.4.4

E-UTRA TDD to UTRA TDD cell re-selection for IncMon p. 393

4.3.4.4.1	Test purpose p. 393
4.3.4.4.2	Test applicability p. 393
4.3.4.4.3	Minimum conformance requirements p. 393
4.3.4.4.4	Test description p. 393
4.3.4.4.5	Test requirement p. 397

4.4

E-UTRAN to GSM Cell Re-Selection p. 400

4.4.1

E-UTRAN FDD - GSM cell re-selection p. 400

4.4.1.1

Test purpose p. 400

4.4.1.2

Test applicability p. 400

4.4.1.3

Minimum conformance requirements p. 400

4.4.1.4

Test description p. 401

4.4.1.4.1	Initial conditions p. 401
4.4.1.4.2	Test procedure p. 402
4.4.1.4.3	Message contents p. 403

4.4.1.5

Test requirement p. 403

4.4.2

E-UTRAN TDD - GSM cell re-selection p. 404

4.4.2.1

Test purpose p. 404

4.4.2.2

Test applicability p. 404

4.4.2.3

Minimum conformance requirements p. 404

4.4.2.4

Test description p. 405

4.4.2.4.1	Initial conditions p. 405
4.4.2.4.2	Test procedure p. 406
4.4.2.4.3	Message contents p. 407

4.4.2.5

Test requirement p. 407

4.5

E-UTRAN to HRPD Cell Re-Selection p. 409

4.5.1

E-UTRAN FDD - HRPD Cell re-selection p. 409

4.5.1.1

E-UTRAN FDD - HRPD Cell Reselection: HRPD is of Lower Priority p. 409

4.5.1.1.1	Test purpose p. 409
4.5.1.1.2	Test applicability p. 409
4.5.1.1.3	Minimum conformance requirements p. 409
4.5.1.1.4	Test description p. 409
4.5.1.1.5	Test requirement p. 411

4.5.2

E-UTRAN TDD - HRPD Cell re-selection p. 412

4.5.2.1

E-UTRAN TDD - HRPD Cell Reselection: HRPD is of Lower Priority p. 412

4.5.2.1.1	Test purpose p. 412
4.5.2.1.2	Test applicability p. 412
4.5.2.1.3	Minimum conformance requirements p. 412
4.5.2.1.4	Test description p. 413
4.5.2.1.5	Test requirement p. 414

4.6

E-UTRAN to cdma2000 1xRTT Cell Re-Selection p. 416

4.6.1

E-UTRAN FDD - cdma2000 1xRTT Cell re-selection p. 416

4.6.1.1

E-UTRAN FDD - cdma2000 1x Cell Reselection: cdma2000 1X is of Lower Priority p. 416

4.6.1.1.1	Test purpose p. 416
4.6.1.1.2	Test applicability p. 416
4.6.1.1.3	Minimum conformance requirements p. 416
4.6.1.1.4	Test description p. 417
4.6.1.1.5	Test requirements p. 418

4.6.2

E-UTRAN TDD - cdma2000 1xRTT Cell re-selection p. 420

4.6.2.1

E-UTRAN TDD - cdma2000 1x Cell Reselection: cdma2000 1X is of Lower Priority p. 420

4.6.2.1.1	Test purpose p. 420
4.6.2.1.2	Test applicability p. 420
4.6.2.1.3	Minimum conformance requirements p. 421
4.6.2.1.4	Test description p. 421
4.6.2.1.5	Test requirements p. 423

E-UTRAN RRC_CONNECTED State Mobility p. 425

5.0

- p. 425

5.1

E-UTRAN Handover p. 425

5.1.1

E-UTRAN FDD-FDD Handover intra frequency case p. 425

5.1.1.1

Test purpose p. 425

5.1.1.2

Test applicability p. 425

5.1.1.3

Minimum conformance requirements p. 425

5.1.1.4

Test description p. 426

5.1.1.4.1	Initial conditions p. 426
5.1.1.4.2	Test procedure p. 427
5.1.1.4.3	Message contents p. 428

5.1.1.5

Test requirement p. 429

5.1.2

E-UTRAN TDD-TDD Handover intra frequency case p. 431

5.1.2.1

Test purpose p. 431

5.1.2.2

Test applicability p. 431

5.1.2.3

Minimum conformance requirements p. 431

5.1.2.4

Test description p. 431

5.1.2.4.1	Initial conditions p. 431
5.1.2.4.2	Test procedure p. 432
5.1.2.4.3	Message contents p. 433

5.1.2.5

Test requirement p. 434

5.1.3

E-UTRAN FDD-FDD Handover inter frequency case p. 436

5.1.3.1

Test purpose p. 436

5.1.3.2

Test applicability p. 436

5.1.3.3

Minimum conformance requirements p. 436

5.1.3.4

Test description p. 436

5.1.3.4.1	Initial conditions p. 436
5.1.3.4.2	Test procedure p. 437
5.1.3.4.3	Message contents p. 438

5.1.3.5

Test requirement p. 439

5.1.3_2

E-UTRAN FDD - FDD Inter frequency handover for UE Category 1bis p. 441

5.1.3_2.1

Test purpose p. 441

5.1.3_2.2

Test applicability p. 441

5.1.3_2.3

Minimum conformance requirements p. 441

5.1.3_2.4

Test description p. 441

5.1.3_2.4.1	Initial conditions p. 441
5.1.3_2.4.2	Test procedure p. 442
5.1.3_2.4.3	Message contents p. 442

5.1.3_2.5

Test requirement p. 442

5.1.4

E-UTRAN TDD-TDD Handover inter frequency case p. 444

5.1.4.1

Test purpose p. 444

5.1.4.2

Test applicability p. 444

5.1.4.3

Minimum conformance requirements p. 444

5.1.4.4

Test description p. 444

5.1.4.4.1	Initial conditions p. 444
5.1.4.4.2	Test procedure p. 445
5.1.4.4.3	Message contents p. 446

5.1.4.5

Test requirement p. 447

5.1.4_2

E-UTRAN TDD-TDD Handover inter frequency case for UE Category 1bis p. 449

5.1.4_2.1

Test purpose p. 449

5.1.4_2.2

Test applicability p. 449

5.1.4_2.3

Minimum conformance requirements p. 449

5.1.4_2.4

Test description p. 449

5.1.4_2.4.1	Initial conditions p. 449
5.1.4_2.4.2	Test procedure p. 450
5.1.4_2.4.3	Message contents p. 450

5.1.4_2.5

Test requirement p. 450

5.1.5

E-UTRAN FDD-FDD inter frequency Handover: unknown target cell p. 452

5.1.5.1

Test purpose p. 452

5.1.5.2

Test applicability p. 452

5.1.5.3

Minimum conformance requirements p. 452

5.1.5.4

Test description p. 452

5.1.5.4.1	Initial conditions p. 452
5.1.5.4.2	Test procedure p. 453
5.1.5.4.3	Message contents p. 454

5.1.5.5

Test requirement p. 454

5.1.5_2

E-UTRAN FDD - FDD Inter frequency handover: unknown target cell for UE Category 1bis p. 455

5.1.5_2.1

Test purpose p. 455

5.1.5_2.2

Test applicability p. 455

5.1.5_2.3

Minimum conformance requirements p. 455

5.1.5_2.4

Test description p. 456

5.1.5_2.4.1	Initial conditions p. 456
5.1.5_2.4.2	Test procedure p. 456
5.1.5_2.4.3	Message contents p. 456

5.1.5_2.5

Test requirement p. 456

5.1.6

E-UTRAN TDD-TDD inter frequency handover: unknown target cell p. 458

5.1.6.1

Test purpose p. 458

5.1.6.2

Test applicability p. 458

5.1.6.3

Minimum conformance requirements p. 458

5.1.6.4

Test description p. 458

5.1.6.4.1	Initial conditions p. 458
5.1.6.4.2	Test procedure p. 459
5.1.6.4.3	Message contents p. 460

5.1.6.5

Test requirement p. 460

5.1.6_2

E-UTRAN TDD-TDD inter frequency handover: unknown target cell for UE Category 1bis p. 462

5.1.6_2.1

Test purpose p. 462

5.1.6_2.2

Test applicability p. 462

5.1.6_2.3

Minimum conformance requirements p. 462

5.1.6_2.4

Test description p. 462

5.1.6_2.4.1	Initial conditions p. 462
5.1.6_2.4.2	Test procedure p. 463
5.1.6_2.4.3	Message contents p. 463

5.1.6_2.5

Test requirement p. 463

5.1.7

E-UTRAN FDD-TDD Handover inter frequency case p. 464

5.1.7.1

Test purpose p. 464

5.1.7.2

Test applicability p. 464

5.1.7.3

Minimum conformance requirements p. 464

5.1.7.4

Test description p. 465

5.1.7.4.1	Initial conditions p. 465
5.1.7.4.2	Test procedure p. 466
5.1.7.4.3	Message contents p. 467

5.1.7.5

Test requirement p. 468

5.1.7_2

E-UTRAN FDD - TDD Inter frequency handover for UE Category 1bis p. 470

5.1.7_2.1

Test purpose p. 470

5.1.7_2.2

Test applicability p. 470

5.1.7_2.3

Minimum conformance requirements p. 470

5.1.7_2.4

Test description p. 471

5.1.7_2.4.1	Initial conditions p. 471
5.1.7_2.4.2	Test procedure p. 471
5.1.7_2.4.3	Message contents p. 471

5.1.7_2.5

Test requirement p. 472

5.1.8

E-UTRAN TDD-FDD Handover inter frequency case p. 474

5.1.8.1

Test purpose p. 474

5.1.8.2

Test applicability p. 474

5.1.8.3

Minimum conformance requirements p. 474

5.1.8.4

Test description p. 474

5.1.8.4.1	Initial conditions p. 474
5.1.8.4.2	Test procedure p. 475
5.1.8.4.3	Message contents p. 476

5.1.8.5

Test requirement p. 477

5.1.8_2

E-UTRAN TDD - FDD Inter frequency handover for UE Category 1bis p. 480

5.1.8_2.1

Test purpose p. 480

5.1.8_2.2

Test applicability p. 480

5.1.8_2.3

Minimum conformance requirements p. 480

5.1.8_2.4

Test description p. 480

5.1.8_2.4.1	Initial conditions p. 480
5.1.8_2.4.2	Test procedure p. 481
5.1.8_2.4.3	Message contents p. 481

5.1.8_2.5

Test requirement p. 481

5.1.9

E-UTRAN FDD-FDD Intra frequency handover for 5MHz bandwidth p. 484

5.1.9.1

Test purpose p. 484

5.1.9.2

Test applicability p. 484

5.1.9.3

Minimum conformance requirements p. 484

5.1.9.4

Test description p. 484

5.1.9.4.1	Initial conditions p. 484
5.1.9.4.2	Test procedure p. 484
5.1.9.4.3	Message contents p. 484

5.1.9.5

Test requirement p. 485

5.1.10

E-UTRAN FDD-FDD Handover intra frequency handover for UE category 0 p. 485

5.1.10.1

Test purpose p. 485

5.1.10.2

Test applicability p. 485

5.1.10.3

Minimum conformance requirements p. 485

5.1.10.4

Test description p. 486

5.1.10.4.1	Initial conditions p. 486
5.1.10.4.2	Test procedure p. 487
5.1.10.4.3	Message contents p. 487

5.1.10.5

Test requirement p. 487

5.1.11

E-UTRAN HD-FDD Handover intra frequency handover for UE category 0 p. 489

5.1.11.1

Test purpose p. 489

5.1.11.2

Test applicability p. 489

5.1.11.3

Minimum conformance requirements p. 489

5.1.11.4

Test description p. 489

5.1.11.4.1	Initial conditions p. 489
5.1.11.4.2	Test procedure p. 490
5.1.11.4.3	Message contents p. 491

5.1.11.5

Test requirement p. 491

5.1.12

E-UTRAN TDD-TDD Handover intra frequency handover for UE category 0 p. 493

5.1.12.1

Test purpose p. 493

5.1.12.2

Test applicability p. 493

5.1.12.3

Minimum conformance requirements p. 493

5.1.12.4

Test description p. 493

5.1.12.4.1	Initial conditions p. 493
5.1.12.4.2	Test procedure p. 494
5.1.12.4.3	Message contents p. 495

5.1.12.5

Test requirement p. 495

5.1.13

E-UTRAN FDD-FDD Intra frequency handover for CE UEs in CEModeA p. 497

5.1.13.1

Test purpose p. 497

5.1.13.2

Test applicability p. 497

5.1.13.3

Minimum conformance requirements p. 497

5.1.13.4

Test description p. 498

5.1.13.4.1	Initial conditions p. 498
5.1.13.4.2	Test procedure p. 498
5.1.13.4.3	Message contents p. 499

5.1.13.5

Test requirement p. 502

5.1.14

E-UTRAN HD-FDD Intra frequency handover for CE UEs in CEModeA p. 504

5.1.14.1

Test purpose p. 504

5.1.14.2

Test applicability p. 504

5.1.14.3

Minimum conformance requirements p. 504

5.1.14.4

Test description p. 505

5.1.14.4.1	Initial conditions p. 505
5.1.14.4.2	Test procedure p. 505
5.1.14.4.3	Message contents p. 506

5.1.14.5

Test requirement p. 506

5.1.15

E-UTRAN TDD Intra frequency handover for CE UEs in CEModeA p. 508

5.1.15.1

Test purpose p. 508

5.1.15.2

Test applicability p. 508

5.1.15.3

Minimum conformance requirements p. 508

5.1.15.4

Test description p. 509

5.1.15.4.1	Initial conditions p. 509
5.1.15.4.2	Test procedure p. 510
5.1.15.4.3	Message contents p. 510

5.1.15.5

Test requirement p. 513

5.1.16

E-UTRAN FDD-FDD Intra frequency handover for CE UEs in CEModeB p. 514

5.1.16.1

Test purpose p. 514

5.1.16.2

Test applicability p. 514

5.1.16.3

Minimum conformance requirements p. 514

5.1.16.4

Test description p. 515

5.1.16.4.1	Initial conditions p. 515
5.1.16.4.2	Test procedure p. 516
5.1.16.4.3	Message contents p. 517

5.1.16.5

Test requirement p. 517

5.1.17

E-UTRAN HD-FDD Intra frequency handover for CE UEs in CEModeB p. 518

5.1.17.1

Test purpose p. 518

5.1.17.2

Test applicability p. 518

5.1.17.3

Minimum conformance requirements p. 518

5.1.17.4

Test description p. 519

5.1.17.4.1	Initial conditions p. 519
5.1.17.4.2	Test procedure p. 520
5.1.17.4.3	Message contents p. 521

5.1.17.5

Test requirement p. 521

5.1.18

E-UTRAN TDD Intra frequency handover for CE UEs in CEModeB p. 522

5.1.18.1

Test purpose p. 522

5.1.18.2

Test applicability p. 522

5.1.18.3

Minimum conformance requirements p. 522

5.1.18.4

Test description p. 523

5.1.18.4.1	Initial conditions p. 523
5.1.18.4.2	Test procedure p. 524
5.1.18.4.3	Message contents p. 525

5.1.18.5

Test requirement p. 525

5.1.19

E-UTRAN FDD - FDD Intra frequency handover for UE Category 1bis p. 526

5.1.19.1

Test purpose p. 526

5.1.19.2

Test applicability p. 526

5.1.19.3

Minimum conformance requirements p. 526

5.1.19.4

Test description p. 527

5.1.19.4.1	Initial conditions p. 527
5.1.19.4.2	Test procedure p. 528
5.1.19.4.3	Message contents p. 529

5.1.19.5

Test requirement p. 529

5.1.20

E-UTRAN TDD - TDD Intra frequency handover for UE Category 1bis p. 531

5.1.20.1

Test purpose p. 531

5.1.20.2

Test applicability p. 531

5.1.20.3

Minimum conformance requirements p. 531

5.1.20.4

Test description p. 532

5.1.20.4.1	Initial conditions p. 532
5.1.20.4.2	Test procedure p. 532
5.1.20.4.3	Message contents p. 532

5.1.20.5

Test requirement p. 533

5.1.21_27

Void p. …

5.1.28

E-UTRAN HD-FDD inter frequency handover for CE UEs in CEModeA p. 535

5.1.28.1

Test purpose p. 535

5.1.28.2

Test applicability p. 535

5.1.28.3

Minimum conformance requirements p. 535

5.1.28.4

Test description p. 536

5.1.28.4.1	Initial conditions p. 536
5.1.28.4.2	Test procedure p. 536
5.1.28.4.3	Message contents p. 537

5.1.28.5

Test requirement p. 540

5.1.29_33

Void p. …

5.1.34

E-UTRAN HD-FDD intra frequency handover for CE UEs in CEModeA without SFN acquisition p. 542

5.1.34.1

Test purpose p. 542

5.1.34.2

Test applicability p. 542

5.1.34.3

Minimum conformance requirements p. 542

5.1.34.4

Test description p. 542

5.1.34.4.1	Initial conditions p. 542
5.1.34.4.2	Test procedure p. 543
5.1.34.4.3	Message contents p. 543

5.1.34.5

Test requirement p. 543

5.1.35_40

FFS p. 545

5.1.41

E-UTRAN FDD - FDD Intra-band Inter-frequency sync DAPS handover p. 545

5.1.41.1

Test purpose p. 545

5.1.41.2

Test applicability p. 545

5.1.41.3

Minimum conformance requirements p. 545

5.1.41.4

Test description p. 546

5.1.41.4.1	Initial conditions p. 546
5.1.41.4.2	Test procedure p. 547
5.1.41.4.3	Message contents p. 548

5.1.41.5

Test requirement p. 551

5.1.42

E-UTRAN FDD - FDD Intra-band Inter-frequency async DAPS handover p. 553

5.1.42.1

Test purpose p. 553

5.1.42.2

Test applicability p. 553

5.1.42.3

Minimum conformance requirements p. 553

5.1.42.4

Test description p. 553

5.1.42.4.1	Initial conditions p. 553
5.1.42.4.2	Test procedure p. 554
5.1.42.4.3	Message contents p. 555

5.1.42.5

Test requirement p. 559

5.1.43

E-UTRAN FDD - FDD Inter-band Inter-frequency sync DAPS handover p. 561

5.1.43.1

Test purpose p. 561

5.1.43.2

Test applicability p. 561

5.1.43.3

Minimum conformance requirements p. 561

5.1.43.4

Test description p. 562

5.1.43.4.1	Initial conditions p. 562
5.1.43.4.2	Test procedure p. 562
5.1.43.4.3	Message contents p. 563

5.1.44

E-UTRAN FDD - FDD Inter-band Inter-frequency async DAPS handover p. 569

5.1.44.1

Test purpose p. 569

5.1.44.2

Test applicability p. 569

5.1.44.3

Minimum conformance requirements p. 569

5.1.44.4

Test description p. 570

5.1.44.4.1	Initial conditions p. 570
5.1.44.4.2	Test procedure p. 570
5.1.44.4.3	Message contents p. 571

5.1.45

E-UTRAN FDD - FDD Intra frequency DAPS handover p. 577

5.1.45.1

Test purpose p. 577

5.1.45.2

Test applicability p. 577

5.1.45.3

Minimum conformance requirements p. 577

5.1.45.4

Test description p. 578

5.1.45.4.1	Initial conditions p. 578
5.1.45.4.2	Test procedure p. 578
5.1.45.4.3	Message contents p. 579

5.1.46

E-UTRAN TDD - TDD Intra frequency DAPS handover p. 585

5.1.46.1

Test purpose p. 585

5.1.46.2

Test applicability p. 585

5.1.46.3

Minimum conformance requirements p. 585

5.1.46.4

Test description p. 585

5.1.46.4.1	Initial conditions p. 585
5.1.46.4.2	Test procedure p. 586
5.1.46.4.3	Message contents p. 587

5.1.47

E-UTRAN FDD - FDD Intra frequency conditional handover p. 593

5.1.47.1

Test purpose p. 593

5.1.47.2

Test applicability p. 593

5.1.47.3

Minimum conformance requirements p. 593

5.1.47.4

Test description p. 594

5.1.47.4.1	Initial conditions p. 594
5.1.47.4.2	Test procedure p. 595

5.1.47.5

Test requirement p. 596

5.1.48

E-UTRAN TDD - TDD Intra frequency conditional handover p. 598

5.1.48.1

Test purpose p. 598

5.1.48.2

Test applicability p. 598

5.1.48.3

Minimum conformance requirements p. 598

5.1.48.4

Test description p. 598

5.1.48.4.1	Initial conditions p. 598
5.1.48.4.2	Test procedure p. 599

5.1.49

E-UTRAN FDD - FDD Inter frequency conditional handover p. 602

5.1.49.1

Test purpose p. 602

5.1.49.2

Test applicability p. 602

5.1.49.3

Minimum conformance requirements p. 602

5.1.49.4

Test description p. 602

5.1.49.4.1	Initial conditions p. 602
5.1.49.4.2	Test procedure p. 603

5.1.50

E-UTRAN TDD - TDD Inter frequency conditional handover p. 606

5.1.50.1

Test purpose p. 606

5.1.50.2

Test applicability p. 606

5.1.50.3

Minimum conformance requirements p. 606

5.1.50.4

Test description p. 606

5.1.50.4.1	Initial conditions p. 606
5.1.50.4.2	Test procedure p. 607
5.1.50.4.3	Message contents p. 607

5.1.50.5

Test requirement p. 608

5.1.51

E-UTRAN FDD - TDD Inter frequency conditional handover p. 610

5.1.51.1

Test purpose p. 610

5.1.51.2

Test applicability p. 610

5.1.51.3

Minimum conformance requirements p. 610

5.1.51.4

Test description p. 610

5.1.51.4.1	Initial conditions p. 610
5.1.51.4.2	Test procedure p. 611

5.1.51.5

Test requirement p. 612

5.1.52

E-UTRAN TDD - FDD Inter frequency conditional handover p. 615

5.1.52.1

Test purpose p. 615

5.1.52.2

Test applicability p. 615

5.1.52.3

Minimum conformance requirements p. 615

5.1.52.4

Test description p. 615

5.1.52.4.1	Initial conditions p. 615
5.1.52.4.2	Test procedure p. 616

5.1.52.5

Test requirement p. 617

5.1.53

E-UTRAN TDD - TDD Intra-band Inter-frequency sync DAPS handover p. 620

5.1.53.1

Test purpose p. 620

5.1.53.2

Test applicability p. 620

5.1.53.3

Minimum conformance requirements p. 620

5.1.53.4

Test description p. 620

5.1.53.4.1	Initial conditions p. 620
5.1.53.4.2	Test procedure p. 621
5.1.53.4.3	Message contents p. 622

5.1.54

E-UTRAN TDD - TDD Inter-band Inter-frequency sync DAPS handover p. 628

5.1.54.1

Test purpose p. 628

5.1.54.2

Test applicability p. 628

5.1.54.3

Minimum conformance requirements p. 628

5.1.54.4

Test description p. 629

5.1.54.4.1	Initial conditions p. 629
5.1.54.4.2	Test procedure p. 630
5.1.54.4.3	Message contents p. 630

5.1.55

E-UTRAN FDD - TDD inter-band inter-frequency synchronous DAPS handover p. 636

5.1.55.1

Test purpose p. 636

5.1.55.2

Test applicability p. 636

5.1.55.3

Minimum conformance requirements p. 636

5.1.55.4

Test description p. 637

5.1.55.4.1	Initial conditions p. 637
5.1.55.4.2	Test procedure p. 638
5.1.55.4.3	Message contents p. 638

5.1.56

E-UTRAN TDD - FDD inter-band inter-frequency synchronous DAPS handover p. 645

5.1.56.1

Test purpose p. 645

5.1.56.2

Test applicability p. 645

5.1.56.3

Minimum conformance requirements p. 645

5.1.56.4

Test description p. 645

5.1.56.4.1	Initial conditions p. 645
5.1.56.4.2	Test procedure p. 646
5.1.56.4.3	Message contents p. 647

5.1.57

E-UTRAN FDD - TDD inter-band inter-frequency async DAPS handover p. 654

5.1.57.1

Test purpose p. 654

5.1.57.2

Test applicability p. 654

5.1.57.3

Minimum conformance requirements p. 654

5.1.57.4

Test description p. 654

5.1.57.4.1	Initial conditions p. 654
5.1.57.4.2	Test procedure p. 655
5.1.57.4.3	Message contents p. 656

5.1.58

E-UTRAN TDD - FDD inter-band inter-frequency async DAPS handover p. 662

5.1.58.1

Test purpose p. 662

5.1.58.2

Test applicability p. 662

5.1.58.3

Minimum conformance requirements p. 662

5.1.58.4

Test description p. 663

5.1.58.4.1	Initial conditions p. 663
5.1.58.4.2	Test procedure p. 663
5.1.58.4.3	Message contents p. 664

5.2

Handover from E-UTRAN to other RATs p. 670

5.2.1

E-UTRAN FDD - UTRAN FDD handover p. 670

5.2.1.1

Test purpose p. 670

5.2.1.2

Test applicability p. 670

5.2.1.3

Minimum conformance requirements p. 670

5.2.1.4

Test description p. 671

5.2.1.4.1	Initial conditions p. 671
5.2.1.4.2	Test procedure p. 672
5.2.1.4.3	Message contents p. 672

5.2.1.5

Test requirement p. 674

5.2.2

E-UTRAN TDD - UTRAN FDD handover p. 676

5.2.2.1

Test purpose p. 676

5.2.2.2

Test applicability p. 676

5.2.2.3

Minimum conformance requirements p. 676

5.2.2.4

Test description p. 677

5.2.2.4.1	Initial conditions p. 677
5.2.2.4.2	Test procedure p. 678
5.2.2.4.3	Message contents p. 679

5.2.2.5

Test requirement p. 680

5.2.3

E-UTRAN FDD - GSM handover p. 682

5.2.3.1

Test purpose p. 682

5.2.3.2

Test applicability p. 682

5.2.3.3

Minimum conformance requirements p. 682

5.2.3.4

Test description p. 683

5.2.3.4.1	Initial conditions p. 683
5.2.3.4.2	Test procedure p. 683
5.2.3.4.3	Message contents p. 684

5.2.3.5

Test requirement p. 685

5.2.4

E-UTRAN TDD - UTRAN TDD handover p. 687

5.2.4.1

Test purpose p. 687

5.2.4.2

Test applicability p. 687

5.2.4.3

Minimum conformance requirements p. 687

5.2.4.4

Test description p. 688

5.2.4.4.1	Initial conditions p. 688
5.2.4.4.2	Test procedure p. 688
5.2.4.4.3	Message contents p. 689

5.2.4.5

Test requirement p. 691

5.2.5

E-UTRAN FDD - UTRAN TDD handover p. 693

5.2.5.1

Test purpose p. 693

5.2.5.2

Test applicability p. 693

5.2.5.3

Minimum conformance requirements p. 693

5.2.5.3.1	Void p. …
5.2.5.3.2	1.28Mcps TDD option p. 693
5.2.5.3.3	Void p. …

5.2.5.4

Test description p. 694

5.2.5.4.1	Void p. …
5.2.5.4.2	1.28Mcps TDD option p. 694
5.2.5.4.3	7.68 Mcps TDD option p. 697

5.2.5.5

Test requirement p. 697

5.2.5.5.1	3.84Mcps TDD option p. 697
5.2.5.5.2	1.28Mcps TDD option p. 697
5.2.5.5.3	7.68 Mcps TDD option p. 699

5.2.6

E-UTRA TDD - GSM handover p. 699

5.2.6.1

Test purpose p. 699

5.2.6.2

Test applicability p. 699

5.2.6.3

Minimum conformance requirements p. 699

5.2.6.4

Test description p. 700

5.2.6.4.1	Initial conditions p. 700
5.2.6.4.2	Test procedure p. 701
5.2.6.4.3	Message contents p. 701

5.2.6.5

Test requirement p. 703

5.2.7

E-UTRAN FDD - UTRAN FDD handover: unknown target cell p. 705

5.2.7.1

Test purpose p. 705

5.2.7.2

Test applicability p. 705

5.2.7.3

Minimum conformance requirements p. 705

5.2.7.4

Test description p. 706

5.2.7.4.1	Initial conditions p. 706
5.2.7.4.2	Test procedure p. 706
5.2.7.4.3	Message contents p. 707

5.2.7.5

Test requirement p. 707

5.2.8

E-UTRAN FDD - GSM handover: unknown target cell p. 709

5.2.8.1

Test purpose p. 709

5.2.8.2

Test applicability p. 709

5.2.8.3

Minimum conformance requirements p. 709

5.2.8.4

Test description p. 710

5.2.8.4.1	Initial conditions p. 710
5.2.8.4.2	Test procedure p. 711
5.2.8.4.3	Message contents p. 711

5.2.8.5

Test requirement p. 711

5.2.9

E-UTRAN TDD - GSM handover: unknown target cell p. 713

5.2.9.1

Test purpose p. 713

5.2.9.2

Test applicability p. 713

5.2.9.3

Minimum conformance requirements p. 713

5.2.9.4

Test description p. 714

5.2.9.4.1	Initial conditions p. 714
5.2.9.4.2	Test procedure p. 714
5.2.9.4.3	Message contents p. 715

5.2.9.5

Test requirement p. 715

5.2.10

E-UTRAN TDD - UTRAN TDD handover: unknown target cell p. 716

5.2.10.1

Test purpose p. 716

5.2.10.2

Test applicability p. 717

5.2.10.3

Minimum conformance requirements p. 717

5.2.10.4

Test description p. 717

5.2.10.4.1	Initial conditions p. 717
5.2.10.4.2	Test procedure p. 718
5.2.10.4.3	Message contents p. 719

5.2.10.5

Test requirement p. 719

5.2.11

E-UTRAN FDD - UTRAN FDD handover for 5MHz Bandwidth p. 721

5.2.11.1

Test purpose p. 721

5.2.11.2

Test applicability p. 721

5.2.11.3

Minimum conformance requirements p. 721

5.2.11.4

Test description p. 721

5.2.11.4.1	Initial conditions p. 721
5.2.11.4.2	Test procedure p. 722
5.2.11.4.3	Message contents p. 722

5.2.11.5

Test requirement p. 722

5.3

Handover from E-UTRAN to non-3GPP RATs p. 722

5.3.1

E-UTRAN FDD - HRPD handover p. 722

5.3.1.1

Test purpose p. 723

5.3.1.2

Test applicability p. 723

5.3.1.3

Minimum conformance requirements p. 723

5.3.1.4

Test description p. 723

5.3.1.4.1	Initial conditions p. 723
5.3.1.4.2	Test procedure p. 724
5.3.1.4.3	Message contents p. 725

5.3.1.5

Test requirement p. 730

5.3.2

E-UTRAN FDD - cdma2000 1xRTT handover p. 732

5.3.2.1

Test purpose p. 732

5.3.2.2

Test applicability p. 732

5.3.2.3

Minimum conformance requirements p. 732

5.3.2.4

Test description p. 733

5.3.2.4.1	Initial conditions p. 733
5.3.2.4.2	Test procedure p. 734
5.3.2.4.3	Message contents p. 734

5.3.2.5

Test requirement p. 734

5.3.3

E-UTRAN FDD - HRPD handover: unknown target cell p. 736

5.3.3.1

Test purpose p. 736

5.3.3.2

Test applicability p. 736

5.3.3.3

Minimum conformance requirements p. 736

5.3.3.4

Test description p. 737

5.3.3.4.1	Initial conditions p. 737
5.3.3.4.2	Test procedure p. 738
5.3.3.4.3	Message contents p. 739

5.3.3.5

Test requirement p. 739

5.3.4

E-UTRAN FDD - cdma2000 1xRTT handover: unknown target cell p. 740

5.3.4.1

Test purpose p. 740

5.3.4.2

Test applicability p. 741

5.3.4.3

Minimum conformance requirements p. 741

5.3.4.4

Test description p. 741

5.3.4.4.1	Initial conditions p. 741
5.3.4.4.2	Test procedure p. 742
5.3.4.4.3	Message contents p. 743

5.3.4.5

Test requirement p. 743

5.3.5

E-UTRAN TDD - HRPD handover p. 744

5.3.5.1

Test purpose p. 744

5.3.5.2

Test applicability p. 745

5.3.5.3

Minimum conformance requirements p. 745

5.3.5.4

Test description p. 745

5.3.5.4.1	Initial conditions p. 745
5.3.5.4.2	Test procedure p. 746
5.3.5.4.3	Message contents p. 747

5.3.5.5

Test requirement p. 754

5.3.6

E-UTRAN TDD - cdma2000 1xRTT handover p. 756

5.3.6.1

Test purpose p. 756

5.3.6.2

Test applicability p. 756

5.3.6.3

Minimum conformance requirements p. 756

5.3.6.4

Test description p. 757

5.3.6.4.1	Initial conditions p. 757
5.3.6.4.2	Test procedure p. 758
5.3.6.4.3	Message contents p. 758

5.3.6.5

Test requirement p. 764

RRC Connection Mobility Control p. 767

6.0

- p. 767

6.1

RRC Re-establishment p. 767

6.1.1

E-UTRAN FDD Intra-frequency RRC Re-establishment p. 767

6.1.1.1

Test purpose p. 767

6.1.1.2

Test applicability p. 767

6.1.1.3

Minimum conformance requirements p. 767

6.1.1.4

Test description p. 768

6.1.1.4.1	Initial conditions p. 768
6.1.1.4.2	Test procedure p. 769
6.1.1.4.3	Message contents p. 769

6.1.1.5

Test requirement p. 770

6.1.1_2

E-UTRAN FDD Intra-frequency RRC Re-establishment for UE Category 1bis p. 771

6.1.1_2.1

Test purpose p. 771

6.1.1_2.2

Test applicability p. 771

6.1.1_2.3

Minimum conformance requirements p. 771

6.1.1_2.4

Test description p. 772

6.1.1_2.4.1	Initial conditions p. 772
6.1.1_2.4.2	Test procedure p. 772
6.1.1_2.4.3	Message contents p. 772

6.1.1_2.5

Test requirement p. 772

6.1.2

E-UTRAN FDD Inter-frequency RRC Re-establishment p. 772

6.1.2.1

Test purpose p. 772

6.1.2.2

Test applicability p. 772

6.1.2.3

Minimum conformance requirements p. 772

6.1.2.4

Test description p. 773

6.1.2.4.1	Initial conditions p. 773
6.1.2.4.2	Test procedure p. 774
6.1.2.4.3	Message contents p. 774

6.1.2.5

Test requirement p. 775

6.1.2_2

E-UTRAN FDD Inter-frequency RRC Re-establishment for UE Category 1bis p. 776

6.1.2_2.1

Test purpose p. 776

6.1.2_2.2

Test applicability p. 776

6.1.2_2.3

Minimum conformance requirements p. 776

6.1.2_2.4

Test description p. 776

6.1.2_2.4.1	Initial conditions p. 776
6.1.2_2.4.2	Test procedure p. 777
6.1.2_2.4.3	Message contents p. 777

6.1.2_2.5

Test requirement p. 777

6.1.3

E-UTRAN TDD Intra-frequency RRC Re-establishment p. 777

6.1.3.1

Test purpose p. 777

6.1.3.2

Test applicability p. 777

6.1.3.3

Minimum conformance requirements p. 777

6.1.3.4

Test description p. 778

6.1.3.4.1	Initial conditions p. 778
6.1.3.4.2	Test procedure p. 779
6.1.3.4.3	Message contents p. 779

6.1.3.5

Test requirement p. 780

6.1.3_2

E-UTRAN TDD Intra-frequency RRC Re-establishment for UE Category 1bis p. 781

6.1.3_2.1

Test purpose p. 781

6.1.3_2.2

Test applicability p. 781

6.1.3_2.3

Minimum conformance requirements p. 781

6.1.3_2.4

Test description p. 781

6.1.3_2.4.1	Initial conditions p. 781
6.1.3_2.4.2	Test procedure p. 781
6.1.3_2.4.3	Message contents p. 781

6.1.3_2.5

Test requirement p. 781

6.1.4

E-UTRAN TDD Inter-frequency RRC Re-establishment p. 781

6.1.4.1

Test purpose p. 781

6.1.4.2

Test applicability p. 782

6.1.4.3

Minimum conformance requirements p. 782

6.1.4.4

Test description p. 782

6.1.4.4.1	Initial conditions p. 782
6.1.4.4.2	Test procedure p. 783
6.1.4.4.3	Message contents p. 784

6.1.4.5

Test requirement p. 784

6.1.4_2

E-UTRAN TDD Inter-frequency RRC Re-establishment for UE Category 1bis p. 786

6.1.4_2.1

Test purpose p. 786

6.1.4_2.2

Test applicability p. 786

6.1.4_2.3

Minimum conformance requirements p. 786

6.1.4_2.4

Test description p. 786

6.1.4_2.4.1	Initial conditions p. 786
6.1.4_2.4.2	Test procedure p. 786
6.1.4_2.4.3	Message contents p. 786

6.1.4_2.5

Test requirement p. 786

6.1.5

E-UTRAN FDD Intra-frequency RRC Re-establishment for 5MHz Bandwidth p. 786

6.1.5.1

Test purpose p. 786

6.1.5.2

Test applicability p. 786

6.1.5.3

Minimum conformance requirements p. 787

6.1.5.4

Test description p. 787

6.1.5.4.1	Initial conditions p. 787
6.1.5.4.2	Test procedure p. 787
6.1.5.4.3	Message contents p. 787

6.1.5.5

Test requirement p. 787

6.1.6

E-UTRAN FD-FDD Intra-frequency RRC Re-establishment for UE category 0 p. 788

6.1.6.1

Test purpose p. 788

6.1.6.2

Test applicability p. 788

6.1.6.3

Minimum conformance requirements p. 788

6.1.6.4

Test description p. 789

6.1.6.4.1	Initial conditions p. 789
6.1.6.4.2	Test procedure p. 789
6.1.6.4.3	Message contents p. 790

6.1.6.5

Test requirement p. 790

6.1.7

E-UTRAN HD-FDD Intra-frequency RRC Re-establishment for UE category 0 p. 792

6.1.7.1

Test purpose p. 792

6.1.7.2

Test applicability p. 792

6.1.7.3

Minimum conformance requirements p. 792

6.1.7.4

Test description p. 792

6.1.7.4.1	Initial conditions p. 792
6.1.7.4.2	Test procedure p. 793
6.1.7.4.3	Message contents p. 794

6.1.7.5

Test requirement p. 794

6.1.8

E-UTRAN TDD Intra-frequency RRC Re-establishment for UE category 0 p. 796

6.1.8.1

Test purpose p. 796

6.1.8.2

Test applicability p. 796

6.1.8.3

Minimum conformance requirements p. 796

6.1.8.4

Test description p. 796

6.1.8.4.1	Initial conditions p. 796
6.1.8.4.2	Test procedure p. 797
6.1.8.4.3	Message contents p. 798

6.1.8.5

Test requirement p. 798

6.1.9

E-UTRAN FD-FDD Intra-frequency RRC Re-establishment for CE UE in CEModeA p. 800

6.1.9.1

Test purpose p. 800

6.1.9.2

Test applicability p. 800

6.1.9.3

Minimum conformance requirements p. 800

6.1.9.4

Test description p. 801

6.1.9.4.1	Initial conditions p. 801
6.1.9.4.2	Test procedure p. 801
6.1.9.4.3	Message contents p. 802

6.1.9.5

Test requirement p. 802

6.1.10

E-UTRAN HD-FDD Intra-frequency RRC Re-establishment for CE UE in CEModeA p. 804

6.1.10.1

Test purpose p. 804

6.1.10.2

Test applicability p. 804

6.1.10.3

Minimum conformance requirements p. 804

6.1.10.4

Test description p. 804

6.1.10.4.1	Initial conditions p. 804
6.1.10.4.2	Test procedure p. 805
6.1.10.4.3	Message contents p. 805

6.1.10.5

Test requirement p. 805

6.1.11

E-UTRAN TDD Intra-frequency RRC Re-establishment for CE UE in CEModeA p. 807

6.1.11.1

Test purpose p. 807

6.1.11.2

Test applicability p. 807

6.1.11.3

Minimum conformance requirements p. 807

6.1.11.4

Test description p. 807

6.1.11.4.1	Initial conditions p. 807
6.1.11.4.2	Test procedure p. 808
6.1.11.4.3	Message contents p. 808

6.1.11.5

Test requirement p. 808

6.1.12

E-UTRAN FD-FDD Intra-frequency RRC Re-establishment for CE UE in CEModeB p. 810

6.1.12.1

Test purpose p. 810

6.1.12.2

Test applicability p. 810

6.1.12.3

Minimum conformance requirements p. 810

6.1.12.4

Test description p. 811

6.1.12.4.1	Initial conditions p. 811
6.1.12.4.2	Test procedure p. 811
6.1.12.4.3	Message contents p. 812

6.1.12.5

Test requirement p. 812

6.1.13

E-UTRAN HD-FDD Intra-frequency RRC Re-establishment for CE UE in CEModeB p. 814

6.1.13.1

Test purpose p. 814

6.1.13.2

Test applicability p. 814

6.1.13.3

Minimum conformance requirements p. 814

6.1.13.4

Test description p. 814

6.1.13.4.1	Initial conditions p. 814
6.1.13.4.2	Test procedure p. 815
6.1.13.4.3	Message contents p. 815

6.1.13.5

Test requirement p. 815

6.1.14

E-UTRAN TDD Intra-frequency RRC Re-establishment for CE UE in CEModeB p. 817

6.1.14.1

Test purpose p. 817

6.1.14.2

Test applicability p. 817

6.1.14.3

Minimum conformance requirements p. 817

6.1.14.4

Test description p. 817

6.1.14.4.1	Initial conditions p. 817
6.1.14.4.2	Test procedure p. 818
6.1.14.4.3	Message contents p. 818

6.1.14.5

Test requirement p. 818

6.1.15

HD-FDD Intra-frequency RRC Re-establishment for category NB1 UE in In-Band mode under enhanced coverage p. 820

6.1.15.1

Test purpose p. 820

6.1.15.2

Test applicability p. 820

6.1.15.3

Minimum conformance requirements p. 820

6.1.15.4

Test description p. 820

6.1.15.4.1	Initial conditions p. 820
6.1.15.4.2	Test procedure p. 821
6.1.15.4.3	Message contents p. 822

6.1.15.5

Test requirement p. 822

6.1.16

HD-FDD Inter-frequency RRC Re-establishment for category NB1 UE in In-Band mode under normal coverage p. 824

6.1.16.1

Test purpose p. 824

6.1.16.2

Test applicability p. 824

6.1.16.3

Minimum conformance requirements p. 824

6.1.16.4

Test description p. 824

6.1.16.4.1	Initial conditions p. 824
6.1.16.4.2	Test procedure p. 825
6.1.16.4.3	Message contents p. 826

6.1.16.5

Test requirement p. 826

6.1.17

Void p. …

6.1.18

E-UTRAN HD-FDD Inter-frequency RRC Re-establishment for CE UE in CEModeA p. 828

6.1.18.1

Test purpose p. 828

6.1.18.2

Test applicability p. 828

6.1.18.3

Minimum conformance requirements p. 828

6.1.18.4

Test description p. 828

6.1.18.4.1	Initial conditions p. 828
6.1.18.4.2	Test procedure p. 829
6.1.18.4.3	Message contents p. 829

6.1.18.5

Test requirement p. 830

6.1.23

E-UTRAN TDD Inter-frequency RRC Re-establishment for UE category NB1 in In-Band mode under normal coverage p. 831

6.1.23.1

Test purpose p. 831

6.1.23.2

Test applicability p. 831

6.1.23.3

Minimum conformance requirements p. 832

6.1.23.4

Test description p. 832

6.1.23.4.1	Initial conditions p. 832
6.1.23.4.2	Test procedure p. 833
6.1.23.4.3	Message contents p. 833

6.1.23.5

Test requirement p. 833

6.1.24

E-UTRAN TDD - TDD Intra-frequency RRC Re-establishment for UE category NB1 in In-Band mode under enhanced coverage p. 835

6.1.24.1

Test purpose p. 835

6.1.24.2

Test applicability p. 835

6.1.24.3

Minimum conformance requirements p. 835

6.1.24.4

Test description p. 836

6.1.24.4.1	Initial conditions p. 836
6.1.24.4.2	Test procedure p. 836
6.1.24.4.3	Message contents p. 836

6.1.24.5

Test requirement p. 837

6.2

Random Access p. 838

6.2.1

E-UTRAN FDD - Contention Based Random Access Test p. 838

6.2.1.1

Test purpose p. 838

6.2.1.2

Test applicability p. 838

6.2.1.3

Minimum conformance requirements p. 838

6.2.1.4

Test description p. 839

6.2.1.4.1	Initial conditions p. 839
6.2.1.4.2	Test procedure p. 839
6.2.1.4.3	Message contents p. 841

6.2.1.5

Test requirement p. 841

6.2.1_2

E-UTRAN FDD - Contention Based Random Access Test for UE Category 1bis p. 844

6.2.1_2.1

Test purpose p. 844

6.2.1_2.2

Test applicability p. 844

6.2.1_2.3

Minimum conformance requirements p. 844

6.2.1_2.4

Test description p. 844

6.2.1_2.4.1	Initial conditions p. 844
6.2.1_2.4.2	Test procedure p. 844
6.2.1_2.4.3	Message contents p. 844

6.2.1_2.5

Test requirement p. 844

6.2.2

E-UTRAN FDD - Non-Contention Based Random Access Test p. 844

6.2.2.1

Test purpose p. 844

6.2.2.2

Test applicability p. 844

6.2.2.3

Minimum conformance requirements p. 845

6.2.2.4

Test description p. 845

6.2.2.4.1	Initial conditions p. 845
6.2.2.4.2	Test procedure p. 845
6.2.2.4.3	Message contents p. 846

6.2.2.5

Test requirement p. 847

6.2.2_2

E-UTRAN FDD - Non-Contention Based Random Access Test for UE Category 1bis p. 848

6.2.2_2.1

Test purpose p. 848

6.2.2_2.2

Test applicability p. 849

6.2.2_2.3

Minimum conformance requirements p. 849

6.2.2_2.4

Test description p. 849

6.2.2_2.4.1	Initial conditions p. 849
6.2.2_2.4.2	Test procedure p. 849
6.2.2_2.4.3	Message contents p. 849

6.2.2_2.5

Test requirement p. 849

6.2.3

E-UTRAN TDD - Contention Based Random Access Test p. 849

6.2.3.1

Test purpose p. 849

6.2.3.2

Test applicability p. 849

6.2.3.3

Minimum conformance requirements p. 849

6.2.3.4

Test description p. 850

6.2.3.4.1	Initial conditions p. 850
6.2.3.4.2	Test procedure p. 850
6.2.3.4.3	Message contents p. 852

6.2.3.5

Test requirement p. 852

6.2.3_2

E-UTRAN TDD - Contention Based Random Access Test for UE Category 1bis p. 855

6.2.3_2.1

Test purpose p. 855

6.2.3_2.2

Test applicability p. 855

6.2.3_2.3

Minimum conformance requirements p. 855

6.2.3_2.4

Test description p. 855

6.2.3_2.4.1	Initial conditions p. 855
6.2.3_2.4.2	Test procedure p. 855
6.2.3_2.4.3	Message contents p. 855

6.2.3_2.5

Test requirement p. 855

6.2.4

E-UTRAN TDD - Non-Contention Based Random Access Test p. 855

6.2.4.1

Test purpose p. 855

6.2.4.2

Test applicability p. 855

6.2.4.3

Minimum conformance requirements p. 856

6.2.4.4

Test description p. 856

6.2.4.4.1	Initial conditions p. 856
6.2.4.4.2	Test procedure p. 856
6.2.4.4.3	Message contents p. 857

6.2.4.5

Test requirement p. 858

6.2.4_2

E-UTRAN TDD - Non-Contention Based Random Access Test for UE Category 1bis p. 860

6.2.4_2.1

Test purpose p. 860

6.2.4_2.2

Test applicability p. 860

6.2.4_2.3

Minimum conformance requirements p. 860

6.2.4_2.4

Test description p. 860

6.2.4_2.4.1	Initial conditions p. 860
6.2.4_2.4.2	Test procedure p. 860
6.2.4_2.4.3	Message contents p. 860

6.2.4_2.5

Test requirement p. 860

6.2.5

E-UTRAN FDD - Contention Based Random Access Test for 5MHz Bandwidth p. 860

6.2.5.1

Test purpose p. 860

6.2.5.2

Test applicability p. 861

6.2.5.3

Minimum conformance requirements p. 861

6.2.5.4

Test description p. 861

6.2.5.4.1	Initial conditions p. 861
6.2.5.4.2	Test procedure p. 861
6.2.5.4.3	Message contents p. 861

6.2.5.5

Test requirement p. 861

6.2.6

E-UTRAN FDD - Non-Contention Based Random Access Test for 5MHz Bandwidth p. 862

6.2.6.1

Test purpose p. 862

6.2.6.2

Test applicability p. 862

6.2.6.3

Minimum conformance requirements p. 862

6.2.6.4

Test description p. 862

6.2.6.4.1	Initial conditions p. 862
6.2.6.4.2	Test procedure p. 862
6.2.6.4.3	Message contents p. 863

6.2.6.5

Test requirement p. 863

6.2.7

E-UTRAN FDD - Non-Contention Based Random Access Test for SCell in sTAG p. 863

6.2.7.1

Test purpose p. 863

6.2.7.2

Test applicability p. 863

6.2.7.3

Minimum conformance requirements p. 863

6.2.7.4

Test description p. 864

6.2.7.4.1	Initial conditions p. 864
6.2.7.4.2	Test procedure p. 864
6.2.7.4.3	Message contents p. 865

6.2.7.5

Test requirement p. 867

6.2.8

E-UTRAN TDD - Non-Contention Based Random Access Test for SCell in sTAG p. 870

6.2.8.1

Test purpose p. 870

6.2.8.2

Test applicability p. 870

6.2.8.3

Minimum conformance requirements p. 870

6.2.8.4

Test description p. 870

6.2.8.4.1	Initial conditions p. 870
6.2.8.4.2	Test procedure p. 871
6.2.8.4.3	Message contents p. 872

6.2.8.5

Test requirement p. 874

6.2.9

3DL/3UL TDD CA Non-Contention Based Random Access Test for 2 SCells p. 876

6.2.9.1

Test purpose p. 876

6.2.9.2

Test applicability p. 876

6.2.9.3

Minimum conformance requirements p. 876

6.2.9.4

Test description p. 877

6.2.9.4.1	Initial conditions p. 877
6.2.9.4.2	Test procedure p. 877
6.2.9.4.3	Message contents p. 878

6.2.9.5

Test requirement p. 881

6.2.10

E-UTRAN FDD - Contention based random access test for CE UEs in normal coverage p. 884

6.2.10.1

Test purpose p. 884

6.2.10.2

Test applicability p. 884

6.2.10.3

Minimum conformance requirements p. 884

6.2.10.4

Test description p. 885

6.2.10.4.1	Initial conditions p. 885
6.2.10.4.2	Test procedures p. 885
6.2.10.4.3	Message contents p. 887

6.2.10.5

Test requirement p. 889

6.2.11

E-UTRAN HD-FDD - Contention based random access test for CE UEs in normal coverage p. 892

6.2.11.1

Test purpose p. 892

6.2.11.2

Test applicability p. 892

6.2.11.3

Minimum conformance requirements p. 892

6.2.11.4

Test description p. 893

6.2.11.4.1	Initial conditions p. 893
6.2.11.4.2	Test procedures p. 893
6.2.11.4.3	Message contents p. 893

6.2.11.5

Test requirement p. 893

6.2.12

E-UTRAN TDD Contention Based Random Access Test for CE UEs in Normal Coverage p. 896

6.2.12.1

Test purpose p. 896

6.2.12.2

Test applicability p. 896

6.2.12.3

Minimum conformance requirements p. 896

6.2.12.4

Test description p. 897

6.2.12.4.1	Initial conditions p. 897
6.2.12.4.2	Test procedure p. 897
6.2.12.4.3	Message contents p. 897

6.2.12.5

Test requirement p. 897

6.2.13

E-UTRAN FDD - Contention Based Random Access Test for CE UEs in Enhanced Coverage p. 900

6.2.13.1

Test purpose p. 900

6.2.13.2

Test applicability p. 900

6.2.13.3

Minimum conformance requirements p. 900

6.2.13.4

Test description p. 901

6.2.13.4.1	Initial conditions p. 901
6.2.13.4.2	Test procedures p. 902
6.2.13.4.3	Message contents p. 903

6.2.13.5

Test requirement p. 906

6.2.14

E-UTRAN HD-FDD - Contention Based Random Access Test for CE UEs in Enhanced Coverage p. 908

6.2.14.1

Test purpose p. 908

6.2.14.2

Test applicability p. 908

6.2.14.3

Minimum conformance requirements p. 908

6.2.14.4

Test description p. 909

6.2.14.4.1	Initial conditions p. 909
6.2.14.4.2	Test procedures p. 909
6.2.14.4.3	Message contents p. 909

6.2.14.5

Test requirement p. 909

6.2.15

E-UTRAN TDD - Contention Based Random Access Test for CE UEs in Enhanced Coverage p. 912

6.2.15.1

Test purpose p. 912

6.2.15.2

Test applicability p. 912

6.2.15.3

Minimum conformance requirements p. 912

6.2.15.4

Test description p. 913

6.2.15.4.1	Initial conditions p. 913
6.2.15.4.2	Test procedures p. 913
6.2.15.4.3	Message contents p. 913

6.2.15.5

Test requirement p. 913

6.2.16

Contention Based Random Access Test for UE category NB1 UEs In-band mode in normal coverage p. 916

6.2.16.1

Test purpose p. 916

6.2.16.2

Test applicability p. 916

6.2.16.3

Minimum conformance requirements p. 916

6.2.16.4

Test description p. 917

6.2.16.4.1	Initial conditions p. 917
6.2.16.4.2	Test procedure p. 918
6.2.16.4.3	Message contents p. 920

6.2.16.5

Test requirement p. 922

6.2.17

Contention Based Random Access Test for UE category NB1 UEs In-band mode in Enhanced Coverage p. 926

6.2.17.1

Test purpose p. 926

6.2.17.2

Test applicability p. 926

6.2.17.3

Minimum conformance requirements p. 926

6.2.17.4

Test description p. 926

6.2.17.4.1	Initial conditions p. 926
6.2.17.4.2	Test procedure p. 926
6.2.17.4.3	Message contents p. 928

6.2.17.5

Test requirement p. 931

6.2.18

Contention Based Random Access on Non-anchor Carrier Test for UE category NB1 UEs In-band mode in Enhanced Coverage p. 935

6.2.18.1

Test purpose p. 935

6.2.18.2

Test applicability p. 935

6.2.18.3

Minimum conformance requirements p. 935

6.2.18.4

Test description p. 935

6.2.18.4.1	Initial conditions p. 935
6.2.18.4.2	Test procedure p. 935
6.2.18.4.3	Message contents p. 935

6.2.18.5

Test requirement p. 939

6.2.19

TDD Contention Based Random Access Test for UE category NB1 UEs In-band mode in normal coverage p. 943

6.2.19.1

Test purpose p. 943

6.2.19.2

Test applicability p. 943

6.2.19.3

Minimum conformance requirements p. 943

6.2.19.4

Test description p. 944

6.2.19.4.1	Initial conditions p. 944
6.2.19.4.2	Test procedure p. 944
6.2.19.4.3	Message contents p. 944

6.2.19.5

Test requirement p. 944

6.2.20

TDD Contention Based Random Access Test for UE category NB1 UEs In-band mode in enhanced coverage p. 949

6.2.20.1

Test purpose p. 949

6.2.20.2

Test applicability p. 949

6.2.20.3

Minimum conformance requirements p. 949

6.2.20.4

Test description p. 949

6.2.20.4.1	Initial conditions p. 949
6.2.20.4.2	Test procedure p. 949
6.2.20.4.3	Message contents p. 949

6.2.20.5

Test requirement p. 949

6.2.21

TDD Contention Based Random Access on Non-anchor Carrier Test for UE category NB1 UEs In-band mode in Enhanced Coverage p. 953

6.3

RRC Connection Release with Redirection p. 961

6.3.1

Redirection from E-UTRAN FDD to UTRAN FDD p. 961

6.3.1.1

Test purpose p. 961

6.3.1.2

Test applicability p. 961

6.3.1.3

Minimum conformance requirements p. 961

6.3.1.4

Test description p. 962

6.3.1.4.1	Initial conditions p. 962
6.3.1.4.2	Test procedure p. 963
6.3.1.4.3	Message contents p. 963

6.3.1.5

Test requirement p. 964

6.3.1_2

Redirection from E-UTRAN FDD to UTRAN FDD for UE Category 1bis p. 965

6.3.1_2.1

Test purpose p. 965

6.3.1_2.2

Test applicability p. 965

6.3.1_2.3

Minimum conformance requirements p. 966

6.3.1_2.4

Test description p. 966

6.3.1_2.4.1	Initial conditions p. 966
6.3.1_2.4.2	Test procedure p. 966
6.3.1_2.4.3	Message contents p. 966

6.3.1_2.5

Test requirement p. 966

6.3.2

Redirection from E-UTRAN TDD to UTRAN FDD p. 966

6.3.2.1

Test purpose p. 966

6.3.2.2

Test applicability p. 966

6.3.2.3

Minimum conformance requirements p. 966

6.3.2.4

Test description p. 967

6.3.2.4.1	Initial conditions p. 967
6.3.2.4.2	Test procedure p. 968
6.3.2.4.3	Message contents p. 968

6.3.2.5

Test requirement p. 969

6.3.2_2

Redirection from E-UTRAN TDD to UTRAN FDD for UE Category 1bis p. 970

6.3.2_2.1

Test purpose p. 970

6.3.2_2.2

Test applicability p. 970

6.3.2_2.3

Minimum conformance requirements p. 971

6.3.2_2.4

Test description p. 971

6.3.2_2.4.1	Initial conditions p. 971
6.3.2_2.4.2	Test procedure p. 971
6.3.2_2.4.3	Message contents p. 971

6.3.2_2.5

Test requirement p. 971

6.3.3

Redirection from E-UTRAN FDD to GERAN when System Information is provided p. 971

6.3.3.1

Test Purpose p. 971

6.3.3.2

Test applicability p. 971

6.3.3.3

Minimum conformance requirements p. 971

6.3.3.4

Test description p. 972

6.3.3.4.1	Initial conditions p. 972
6.3.3.4.2	Test procedure p. 972
6.3.3.4.3	Message contents p. 973

6.3.3.5

Test requirement p. 974

6.3.3_2

Redirection from E-UTRAN FDD to GERAN when System Information is provided for UE Category 1bis p. 975

6.3.3_2.1

Test purpose p. 975

6.3.3_2.2

Test applicability p. 975

6.3.3_2.3

Minimum conformance requirements p. 975

6.3.3_2.4

Test description p. 975

6.3.3_2.4.1	Initial conditions p. 975
6.3.3_2.4.2	Test procedure p. 975
6.3.3_2.4.3	Message contents p. 976

6.3.3_2.5

Test requirement p. 976

6.3.4

Redirection from E-UTRAN TDD to GERAN when System Information is provided p. 976

6.3.4.1

Test Purpose p. 976

6.3.4.2

Test applicability p. 976

6.3.4.3

Minimum conformance requirements p. 976

6.3.4.4

Test description p. 976

6.3.4.4.1	Initial conditions p. 976
6.3.4.4.2	Test procedure p. 977
6.3.4.4.3	Message contents p. 978

6.3.4.5

Test requirement p. 978

6.3.4_2

Redirection from E-UTRAN TDD to GERAN when System Information is provided for UE Category 1bis p. 980

6.3.4_2.1

Test purpose p. 980

6.3.4_2.2

Test applicability p. 980

6.3.4_2.3

Minimum conformance requirements p. 980

6.3.4_2.4

Test description p. 980

6.3.4_2.4.1	Initial conditions p. 980
6.3.4_2.4.2	Test procedure p. 980
6.3.4_2.4.3	Message contents p. 980

6.3.4_2.5

Test requirement p. 980

6.3.5

E-UTRA TDD RRC connection release redirection to UTRA TDD p. 980

6.3.5.1

Test purpose p. 980

6.3.5.2

Test applicability p. 981

6.3.5.3

Minimum conformance requirements p. 981

6.3.5.4

Test description p. 981

6.3.5.4.1	Initial conditions p. 981
6.3.5.4.2	Test procedure p. 982
6.3.5.4.3	Message contents p. 983

6.3.5.5

Test requirement p. 983

6.3.5_2

E-UTRA TDD RRC connection release redirection to UTRA TDD for UE Category 1bis p. 985

6.3.5_2.1

Test purpose p. 985

6.3.5_2.2

Test applicability p. 986

6.3.5_2.3

Minimum conformance requirements p. 986

6.3.5_2.4

Test description p. 986

6.3.5_2.4.1	Initial conditions p. 986
6.3.5_2.4.2	Test procedure p. 986
6.3.5_2.4.3	Message contents p. 986

6.3.5_2.5

Test requirement p. 986

6.3.6

E-UTRA FDD RRC connection release redirection to UTRA TDD p. 986

6.3.6.1

Test purpose p. 986

6.3.6.2

Test applicability p. 986

6.3.6.3

Minimum conformance requirements p. 986

6.3.6.4

Test description p. 987

6.3.6.4.1	Initial conditions p. 987
6.3.6.4.2	Test procedure p. 988
6.3.6.4.3	Message contents p. 988

6.3.6.5

Test requirement p. 989

6.3.6_2

E-UTRA FDD RRC connection release redirection to UTRA TDD for UE Category 1bis p. 991

6.3.6_2.1

Test purpose p. 991

6.3.6_2.2

Test applicability p. 992

6.3.6_2.3

Minimum conformance requirements p. 992

6.3.6_2.4

Test description p. 992

6.3.6_2.4.1	Initial conditions p. 992
6.3.6_2.4.2	Test procedure p. 992
6.3.6_2.4.3	Message contents p. 992

6.3.6_2.5

Test requirement p. 992

6.3.7

E-UTRA TDD RRC connection release redirection to UTRA TDD without SI provided p. 992

6.3.7.1

Test purpose p. 992

6.3.7.2

Test applicability p. 992

6.3.7.3

Minimum conformance requirements p. 992

6.3.7.4

Test description p. 993

6.3.7.4.1	Initial conditions p. 993
6.3.7.4.2	Test procedure p. 994
6.3.7.4.3	Message contents p. 995

6.3.7.5

Test requirement p. 995

6.3.7_2

E-UTRA TDD RRC connection release redirection to UTRA TDD without SI provided for UE Category 1bis p. 997

6.3.7_2.1

Test purpose p. 997

6.3.7_2.2

Test applicability p. 997

6.3.7_2.3

Minimum conformance requirements p. 997

6.3.7_2.4

Test description p. 997

6.3.7_2.4.1	Initial conditions p. 997
6.3.7_2.4.2	Test procedure p. 997
6.3.7_2.4.3	Message contents p. 997

6.3.7_2.5

Test requirement p. 997

6.3.8

E-UTRA FDD RRC connection release redirection to UTRA TDD without SI provided p. 997

6.3.8.1

Test purpose p. 997

6.3.8.2

Test applicability p. 997

6.3.8.3

Minimum conformance requirements p. 998

6.3.8.4

Test description p. 998

6.3.8.4.1	Initial conditions p. 998
6.3.8.4.2	Test procedure p. 999
6.3.8.4.3	Message contents p. 999

6.3.8.5

Test requirement p. 1000

6.3.8_2

E-UTRA FDD RRC connection release redirection to UTRA TDD without SI provided for UE Category 1bis p. 1002

6.3.8_2.1

Test purpose p. 1002

6.3.8_2.2

Test applicability p. 1002

6.3.8_2.3

Minimum conformance requirements p. 1002

6.3.8_2.4

Test description p. 1002

6.3.8_2.4.1	Initial conditions p. 1002
6.3.8_2.4.2	Test procedure p. 1002
6.3.8_2.4.3	Message contents p. 1002

6.3.8_2.5

Test requirement p. 1002

6.3.9

Redirection from E-UTRAN FDD to UTRAN FDD without System Information p. 1002

6.3.9.1

Test purpose p. 1002

6.3.9.2

Test applicability p. 1002

6.3.9.3

Minimum conformance requirements p. 1003

6.3.9.4

Test description p. 1003

6.3.9.4.1	Initial conditions p. 1003
6.3.9.4.2	Test procedure p. 1004
6.3.9.4.3	Message contents p. 1004

6.3.9.5

Test requirement p. 1005

6.3.9_2

Redirection from E-UTRAN FDD to UTRAN FDD without System Information for UE Category 1bis p. 1007

6.3.9_2.1

Test purpose p. 1007

6.3.9_2.2

Test applicability p. 1007

6.3.9_2.3

Minimum conformance requirements p. 1007

6.3.9_2.4

Test description p. 1007

6.3.9_2.4.1	Initial conditions p. 1007
6.3.9_2.4.2	Test procedure p. 1007
6.3.9_2.4.3	Message contents p. 1007

6.3.9_2.5

Test requirement p. 1008

6.3.10

Redirection from E-UTRAN FDD to GERAN when System Information is not provided p. 1008

6.3.10.1

Test Purpose p. 1008

6.3.10.2

Test applicability p. 1008

6.3.10.3

Minimum conformance requirements p. 1008

6.3.10.4

Test description p. 1008

6.3.10.4.1	Initial conditions p. 1008
6.3.10.4.2	Test procedure p. 1009
6.3.10.4.3	Message contents p. 1010

6.3.10.5

Test requirement p. 1010

6.3.10_2

Redirection from E-UTRAN FDD to GERAN when System Information is not provided for UE Category 1bis p. 1011

6.3.10_2.1

Test purpose p. 1011

6.3.10_2.2

Test applicability p. 1011

6.3.10_2.3

Minimum conformance requirements p. 1011

6.3.10_2.4

Test description p. 1012

6.3.10_2.4.1	Initial conditions p. 1012
6.3.10_2.4.2	Test procedure p. 1012
6.3.10_2.4.3	Message contents p. 1012

6.3.10_2.5

Test requirement p. 1012

6.3.11

Redirection from E-UTRAN TDD to GERAN when System Information is not provided p. 1012

6.3.11.1

Test Purpose p. 1012

6.3.11.2

Test applicability p. 1012

6.3.11.3

Minimum conformance requirements p. 1012

6.3.11.4

Test description p. 1013

6.3.11.4.1	Initial conditions p. 1013
6.3.11.4.2	Test procedure p. 1013
6.3.11.4.3	Message contents p. 1014

6.3.11.5

Test requirement p. 1014

6.3.11_2

Redirection from E-UTRAN TDD to GERAN when System Information is not provided for UE Category 1bis p. 1016

6.3.11_2.1

Test purpose p. 1016

6.3.11_2.2

Test applicability p. 1016

6.3.11_2.3

Minimum conformance requirements p. 1016

6.3.11_2.4

Test description p. 1016

6.3.11_2.4.1	Initial conditions p. 1016
6.3.11_2.4.2	Test procedure p. 1016
6.3.11_2.4.3	Message contents p. 1016

6.3.11_2.5

Test requirement p. 1016

6.3.12

E-UTRAN TDD RRC connection release redirection to UTRAN FDD without SI provided p. 1016

6.3.12.1

Test purpose p. 1016

6.3.12.2

Test applicability p. 1016

6.3.12.3

Minimum conformance requirements p. 1017

6.3.12.4

Test description p. 1017

6.3.12.4.1	Initial conditions p. 1017
6.3.12.4.2	Test procedure p. 1018
6.3.12.4.3	Message contents p. 1019

6.3.12.5

Test requirement p. 1019

6.3.12_2

Redirection from E-UTRAN TDD to UTRAN FDD without System Information for UE Category 1bis p. 1021

6.3.12_2.1

Test purpose p. 1021

6.3.12_2.2

Test applicability p. 1021

6.3.12_2.3

Minimum conformance requirements p. 1021

6.3.12_2.4

Test description p. 1021

6.3.12_2.4.1	Initial conditions p. 1021
6.3.12_2.4.2	Test procedure p. 1021
6.3.12_2.4.3	Message contents p. 1021

6.3.12_2.5

Test requirement p. 1021

Timing and Signalling Characteristic p. 1022

7.0

- p. 1022

7.1

UE Transmit Timing p. 1022

7.1.1

E-UTRAN FDD - UE Transmit Timing Accuracy p. 1022

7.1.1.1

Test purpose p. 1022

7.1.1.2

Test applicability p. 1022

7.1.1.3

Minimum conformance requirements p. 1022

7.1.1.4

Test description p. 1023

7.1.1.4.1	Initial conditions p. 1023
7.1.1.4.2	Test procedure p. 1023
7.1.1.4.3	Message contents p. 1024

7.1.1.5

Test requirement p. 1026

7.1.1_1

E-UTRAN FDD - UE Transmit Timing Accuracy (Non DRx UE) p. 1029

7.1.1_1.1

Test purpose p. 1029

7.1.1_1.2

Test applicability p. 1029

7.1.1_1.3

Minimum conformance requirements p. 1029

7.1.1_1.4

Test description p. 1029

7.1.1_1.4.1	Initial conditions p. 1029
7.1.1_1.4.2	Test procedure p. 1029
7.1.1_1.4.3	Message contents p. 1030

7.1.1_1.5

Test requirement p. 1031

7.1.1_2

E-UTRAN FDD - UE Transmit Timing Accuracy for UE category 1bis p. 1033

7.1.1_2.1

Test purpose p. 1033

7.1.1_2.2

Test applicability p. 1033

7.1.1_2.3

Minimum conformance requirements p. 1033

7.1.1_2.4

Test description p. 1033

7.1.1_2.4.1	Initial conditions p. 1033
7.1.1_2.4.2	Test procedure p. 1033
7.1.1_2.4.3	Message contents p. 1033

7.1.1_2.5

Test requirement p. 1033

7.1.2

E-UTRAN TDD - UE Transmit Timing Accuracy p. 1033

7.1.2.1

Test purpose p. 1033

7.1.2.2

Test applicability p. 1033

7.1.2.3

Minimum conformance requirements p. 1034

7.1.2.4

Test description p. 1035

7.1.2.4.1	Initial conditions p. 1035
7.1.2.4.2	Test procedure p. 1035
7.1.2.4.3	Message contents p. 1036

7.1.2.5

Test requirement p. 1038

7.1.2_1

E-UTRAN TDD - UE Transmit Timing Accuracy (Non DRx UE) p. 1040

7.1.2_1.1

Test purpose p. 1040

7.1.2_1.2

Test applicability p. 1040

7.1.2_1.3

Minimum conformance requirements p. 1040

7.1.2_1.4

Test description p. 1041

7.1.2_1.4.1	Initial conditions p. 1041
7.1.2_1.4.2	Test procedure p. 1041
7.1.2_1.4.3	Message contents p. 1041

7.1.2_1.5

Test requirement p. 1042

7.1.2_2

E-UTRAN TDD - UE Transmit Timing Accuracy for UE category 1bis p. 1044

7.1.2_2.1

Test purpose p. 1044

7.1.2_2.2

Test applicability p. 1044

7.1.2_2.3

Minimum conformance requirements p. 1044

7.1.2_2.4

Test description p. 1044

7.1.2_2.4.1	Initial conditions p. 1044
7.1.2_2.4.2	Test procedure p. 1044
7.1.2_2.4.3	Message contents p. 1045

7.1.2_2.5

Test requirement p. 1047

7.1.3

E-UTRAN FDD - UE Transmit Timing Accuracy Tests for SCell p. 1050

7.1.3.1

Test purpose p. 1050

7.1.3.2

Test applicability p. 1050

7.1.3.3

Minimum conformance requirements p. 1050

7.1.3.4

Test description p. 1051

7.1.3.4.1	Initial conditions p. 1051
7.1.3.4.2	Test procedure p. 1051
7.1.3.4.3	Message contents p. 1052

7.1.3.5

Test requirement p. 1055

7.1.3_1

E-UTRAN FDD - UE Transmit Timing Accuracy Tests for SCell (Rel 12 and forward) p. 1057

7.1.3_1.1

Test purpose p. 1057

7.1.3_1.2

Test applicability p. 1057

7.1.3_1.3

Minimum conformance requirements p. 1057

7.1.3_1.4

Test description p. 1058

7.1.3_1.4.1	Initial conditions p. 1058
7.1.3_1.4.2	Test procedure p. 1058
7.1.3_1.4.3	Message contents p. 1059

7.1.3_1.5

Test requirement p. 1061

7.1.4

E-UTRAN TDD - UE Transmit Timing Accuracy Tests for SCell p. 1064

7.1.4.1

Test purpose p. 1064

7.1.4.2

Test applicability p. 1064

7.1.4.3

Minimum conformance requirements p. 1064

7.1.4.4

Test description p. 1065

7.1.4.4.1	Initial conditions p. 1065
7.1.4.4.2	Test procedure p. 1065
7.1.4.4.3	Message contents p. 1066

7.1.4.5

Test requirement p. 1068

7.1.4_1

E-UTRAN TDD - UE Transmit Timing Accuracy Tests for SCell (Rel 12 and forward) p. 1070

7.1.4_1.1

Test purpose p. 1070

7.1.4_1.2

Test applicability p. 1071

7.1.4_1.3

Minimum conformance requirements p. 1071

7.1.4_1.4

Test description p. 1071

7.1.4_1.4.1	Initial conditions p. 1071
7.1.4_1.4.2	Test procedure p. 1072
7.1.4_1.4.3	Message contents p. 1073

7.1.4_1.5

Test requirement p. 1075

7.1.4A

E-UTRAN TDD - UE Transmit Timing Accuracy Tests for SCell for 20 MHz +10 MHz bandwidth p. 1077

7.1.4A.1

Test purpose p. 1077

7.1.4A.2

Test applicability p. 1077

7.1.4A.3

Minimum conformance requirements p. 1077

7.1.4A.4

Test description p. 1077

7.1.4A.4.1	Initial conditions p. 1077
7.1.4A.4.2	Test procedure p. 1078
7.1.4A.4.3	Message contents p. 1078

7.1.4A.5

Test requirement p. 1078

7.1.5

E-UTRAN FDD - UE Transmit Timing Accuracy Tests for 5MHz Bandwidth p. 1079

7.1.5.1

Test purpose p. 1079

7.1.5.2

Test applicability p. 1079

7.1.5.3

Minimum conformance requirements p. 1080

7.1.5.4

Test description p. 1080

7.1.5.4.1	Initial conditions p. 1080
7.1.5.4.2	Test procedure p. 1080
7.1.5.4.3	Message contents p. 1080

7.1.5.5

Test requirement p. 1082

7.1.6

E-UTRAN FDD - UE Transmit Timing Accuracy Tests for SCell in sTAG p. 1083

7.1.6.1

Test purpose p. 1083

7.1.6.2

Test applicability p. 1083

7.1.6.3

Minimum conformance requirements p. 1084

7.1.6.4

Test description p. 1084

7.1.6.4.1	Initial conditions p. 1084
7.1.6.4.2	Test procedure p. 1085
7.1.6.4.3	Message contents p. 1086

7.1.6.5

Test requirement p. 1088

7.1.7

E-UTRAN TDD - UE Transmit Timing Accuracy Tests for SCell in sTAG p. 1090

7.1.7.1

Test purpose p. 1090

7.1.7.2

Test applicability p. 1090

7.1.7.3

Minimum conformance requirements p. 1090

7.1.7.4

Test description p. 1091

7.1.7.4.1	Initial conditions p. 1091
7.1.7.4.2	Test procedure p. 1091
7.1.7.4.3	Message contents p. 1092

7.1.7.5

Test requirement p. 1092

7.1.7A

E-UTRAN TDD - UE Transmit Timing Accuracy Tests for SCell in sTAG for 20MHz +20MHz bandwidth p. 1095

7.1.7A.1

Test purpose p. 1095

7.1.7A.2

Test applicability p. 1095

7.1.7A.3

Minimum conformance requirements p. 1095

7.1.7A.4

Test description p. 1095

7.1.7A.4.1	Initial conditions p. 1095
7.1.7A.4.2	Test procedure p. 1095
7.1.7A.4.3	Message contents p. 1095

7.1.7A.5

Test requirement p. 1095

7.1.7B

E-UTRAN TDD - UE Transmit Timing Accuracy Tests for SCell in sTAG for 20MHz +10MHz bandwidth p. 1097

7.1.7B.1

Test purpose p. 1097

7.1.7B.2

Test applicability p. 1097

7.1.7B.3

Minimum conformance requirements p. 1097

7.1.7B.4

Test description p. 1097

7.1.7B.4.1	Initial conditions p. 1097
7.1.7B.4.2	Test procedure p. 1097
7.1.7B.4.3	Message contents p. 1097

7.1.7B.5

Test requirement p. 1097

7.1.8

Void p. …

7.1.9

Void p. …

7.1.10

E-UTRAN FDD - UE Transmit Timing Accuracy Tests for Cat-M1 UE in CEModeA p. 1099

7.1.10.1

Test purpose p. 1099

7.1.10.2

Test applicability p. 1099

7.1.10.3

Minimum conformance requirements p. 1100

7.1.10.4

Test description p. 1101

7.1.10.4.1	Initial conditions p. 1101
7.1.10.4.2	Test procedure p. 1101
7.1.10.4.3	Message contents p. 1102

7.1.10.5

Test requirement p. 1104

7.1.11

E-UTRAN HD-FDD - UE Transmit Timing Accuracy Tests for Cat-M1 UE in CEModeA p. 1106

7.1.11.1

Test purpose p. 1106

7.1.11.2

Test applicability p. 1106

7.1.11.3

Minimum conformance requirements p. 1106

7.1.11.4

Test description p. 1107

7.1.11.4.1	Initial conditions p. 1107
7.1.11.4.2	Test procedure p. 1108
7.1.11.4.3	Message contents p. 1108

7.1.11.5

Test requirement p. 1110

7.1.12

E-UTRAN TDD - UE Transmit Timing Accuracy Tests for Cat-M1 UE in CEModeA p. 1113

7.1.12.1

Test purpose p. 1113

7.1.12.2

Test applicability p. 1113

7.1.12.3

Minimum conformance requirements p. 1113

7.1.12.4

Test description p. 1114

7.1.12.4.1	Initial conditions p. 1114
7.1.12.4.2	Test procedure p. 1114
7.1.12.4.3	Message contents p. 1115

7.1.12.5

Test requirement p. 1117

7.1.13

3DL/3UL TDD CA UE Transmit Timing Accuracy Tests for 2 SCells p. 1120

7.1.13.1

Test purpose p. 1120

7.1.13.2

Test applicability p. 1120

7.1.13.3

Minimum conformance requirements p. 1120

7.1.13.4

Test description p. 1121

7.1.13.4.1	Initial conditions p. 1121
7.1.13.4.2	Test procedure p. 1121
7.1.13.4.3	Message contents p. 1122

7.1.13.5

Test requirement p. 1124

7.1.14

E-UTRAN FDD - UE Transmit Timing Accuracy Tests for Cat-M1 UE in CEModeB p. 1127

7.1.14.1

Test purpose p. 1127

7.1.14.2

Test applicability p. 1127

7.1.14.3

Minimum conformance requirements p. 1127

7.1.14.4

Test description p. 1128

7.1.14.4.1	Initial conditions p. 1128
7.1.14.4.2	Test procedure p. 1128
7.1.14.4.3	Message contents p. 1129

7.1.14.5

Test requirement p. 1131

7.1.15

E-UTRAN HD-FDD - UE Transmit Timing Accuracy Tests for Cat-M1 UE in CEModeB p. 1133

7.1.15.1

Test purpose p. 1133

7.1.15.2

Test applicability p. 1133

7.1.15.3

Minimum conformance requirements p. 1133

7.1.15.4

Test description p. 1134

7.1.15.4.1	Initial conditions p. 1134
7.1.15.4.2	Test procedure p. 1134
7.1.15.4.3	Message contents p. 1135

7.1.15.5

Test requirement p. 1136

7.1.16

E-UTRAN TDD - UE Transmit Timing Accuracy Tests for Cat-M1 UE in CEModeB p. 1139

7.1.16.1

Test purpose p. 1139

7.1.16.2

Test applicability p. 1139

7.1.16.3

Minimum conformance requirements p. 1139

7.1.16.4

Test description p. 1140

7.1.16.4.1	Initial conditions p. 1140
7.1.16.4.2	Test procedure p. 1140
7.1.16.4.3	Message contents p. 1141

7.1.16.5

Test requirement p. 1142

7.1.17

HD-FDD Transmit Timing Accuracy Tests for Category NB1 UE in In-Band Mode under Normal Coverage p. 1145

7.1.17.1

Test purpose p. 1145

7.1.17.2

Test applicability p. 1145

7.1.17.3

Minimum conformance requirements p. 1145

7.1.17.4

Test description p. 1145

7.1.17.4.1	Initial conditions p. 1145
7.1.17.4.2	Test procedure p. 1146
7.1.17.4.3	Message contents p. 1147

7.1.17.5

Test requirement p. 1147

7.1.18

HD-FDD Transmit Timing Accuracy Tests for Category NB1 UE in In-Band Mode under Enhanced Coverage p. 1149

7.1.18.1

Test purpose p. 1149

7.1.18.2

Test applicability p. 1149

7.1.18.3

Minimum conformance requirements p. 1149

7.1.18.4

Test description p. 1150

7.1.18.4.1	Initial conditions p. 1150
7.1.18.4.2	Test procedure p. 1150
7.1.18.4.3	Message contents p. 1151

7.1.18.5

Test requirement p. 1152

7.1.19

- p. 1154

7.1.20

- p. 1154

7.1.21

E-UTRAN FDD - UE Transmit Timing Accuracy Tests for CE UE in CEModeA p. 1154

7.1.21.1

Test purpose p. 1154

7.1.21.2

Test applicability p. 1154

7.1.21.3

Minimum conformance requirements p. 1154

7.1.21.4

Test description p. 1155

7.1.21.4.1	Initial conditions p. 1155
7.1.21.4.2	Test procedure p. 1155
7.1.21.4.3	Message contents p. 1156

7.1.21.5

Test requirement p. 1156

7.1.22

E-UTRAN HD-FDD - UE Transmit Timing Accuracy Tests for CE UE in CEModeA p. 1158

7.1.22.1

Test purpose p. 1158

7.1.22.2

Test applicability p. 1159

7.1.22.3

Minimum conformance requirements p. 1159

7.1.22.4

Test description p. 1159

7.1.22.4.1	Initial conditions p. 1159
7.1.22.4.2	Test procedure p. 1159
7.1.22.4.3	Message contents p. 1159

7.1.22.5

Test requirement p. 1159

7.1.23

E-UTRAN TDD - UE Transmit Timing Accuracy Tests for CE UE in CEModeA p. 1162

7.1.23.1

Test purpose p. 1162

7.1.23.2

Test applicability p. 1162

7.1.23.3

Minimum conformance requirements p. 1162

7.1.23.4

Test description p. 1162

7.1.23.4.1	Initial conditions p. 1162
7.1.23.4.2	Test procedure p. 1162
7.1.23.4.3	Message contents p. 1163

7.1.23.5

Test requirement p. 1163

7.1.24

E-UTRAN FDD - UE Transmit Timing Accuracy Tests for CE UE in CEModeB p. 1165

7.1.24.1

Test purpose p. 1165

7.1.24.2

Test applicability p. 1166

7.1.24.3

Minimum conformance requirements p. 1166

7.1.24.4

Test description p. 1167

7.1.24.4.1	Initial conditions p. 1167
7.1.24.4.2	Test procedure p. 1167
7.1.24.4.3	Message contents p. 1168

7.1.24.5

Test requirement p. 1168

7.1.25

- p. 1170

7.1.26

- p. 1170

7.1.27

E-UTRAN TDD - UE Transmit Timing Accuracy Tests for Category NB1 UE In-Band mode under normal coverage p. 1170

7.1.27.1

Test purpose p. 1170

7.1.27.2

Test applicability p. 1170

7.1.27.3

Minimum conformance requirements p. 1170

7.1.27.4

Test description p. 1170

7.1.27.4.1	Initial conditions p. 1170
7.1.27.4.2	Test procedure p. 1171
7.1.27.4.3	Message contents p. 1171

7.1.27.5

Test requirement p. 1171

7.1.28

E-UTRAN TDD - UE Transmit Timing Accuracy Tests for Category NB1 UE In-band mode under enhanced coverage p. 1173

7.1.28.1

Test purpose p. 1173

7.1.28.2

Test applicability p. 1173

7.1.28.3

Minimum conformance requirements p. 1173

7.1.28.4

Test description p. 1173

7.1.28.4.1	Initial conditions p. 1173
7.1.28.4.2	Test procedure p. 1174
7.1.28.4.3	Message contents p. 1174

7.1.28.5

Test requirement p. 1174

7.2

UE Timing Advance p. 1175

7.2.1

E-UTRAN FDD - UE Timing Advance Adjustment Accuracy p. 1175

7.2.1.1

Test purpose p. 1175

7.2.1.2

Test applicability p. 1175

7.2.1.3

Minimum conformance requirements p. 1176

7.2.1.4

Test description p. 1176

7.2.1.4.1	Initial conditions p. 1176
7.2.1.4.2	Test procedure p. 1177
7.2.1.4.3	Message contents p. 1177

7.2.1.5

Test requirement p. 1179

7.2.1_2

E-UTRAN FDD - UE Timing Advance Adjustment Accuracy for UE category 1bis p. 1180

7.2.1_2.1

Test purpose p. 1180

7.2.1_2.2

Test applicability p. 1180

7.2.1_2.3

Minimum conformance requirements p. 1180

7.2.1_2.4

Test description p. 1180

7.2.1_2.4.1	Initial conditions p. 1180
7.2.1_2.4.2	Test procedure p. 1180
7.2.1_2.4.3	Message contents p. 1180

7.2.1_2.5

Test requirement p. 1180

7.2.2

E-UTRAN TDD - UE Timing Advance Adjustment Accuracy p. 1180

7.2.2.1

Test purpose p. 1180

7.2.2.2

Test applicability p. 1180

7.2.2.3

Minimum conformance requirements p. 1181

7.2.2.4

Test description p. 1181

7.2.2.4.1	Initial conditions p. 1181
7.2.2.4.2	Test procedure p. 1182
7.2.2.4.3	Message contents p. 1182

7.2.2.5

Test requirement p. 1184

7.2.2_2

E-UTRAN TDD - UE Timing Advance Adjustment Accuracy for UE category 1bis p. 1185

7.2.2_2.1

Test purpose p. 1185

7.2.2_2.2

Test applicability p. 1185

7.2.2_2.3

Minimum conformance requirements p. 1185

7.2.2_2.4

Test description p. 1185

7.2.2_2.4.1	Initial conditions p. 1185
7.2.2_2.4.2	Test procedure p. 1185
7.2.2_2.4.3	Message contents p. 1185

7.2.2_2.5

Test requirement p. 1185

7.2.3

E-UTRAN FDD - UE Timing Advance Adjustment Accuracy Test for 5MHz Bandwidth p. 1185

7.2.3.1

Test purpose p. 1185

7.2.3.2

Test applicability p. 1185

7.2.3.3

Minimum conformance requirements p. 1186

7.2.3.4

Test description p. 1186

7.2.3.4.1	Initial conditions p. 1186
7.2.3.4.2	Test procedure p. 1186
7.2.3.4.3	Message contents p. 1186

7.2.3.5

Test requirement p. 1186

7.2.4

E-UTRAN FDD - UE Timing Advance Adjustment Accuracy Test for SCell in sTAG p. 1187

7.2.4.1

Test purpose p. 1187

7.2.4.2

Test applicability p. 1187

7.2.4.3

Minimum conformance requirements p. 1187

7.2.4.4

Test description p. 1187

7.2.4.4.1	Initial conditions p. 1187
7.2.4.4.2	Test procedure p. 1188
7.2.4.4.3	Message contents p. 1189

7.2.4.5

Test requirement p. 1191

7.2.5

E-UTRAN TDD - UE Timing Advance Adjustment Accuracy Test for SCell in sTAG p. 1192

7.2.5.1

Test purpose p. 1192

7.2.5.2

Test applicability p. 1192

7.2.5.3

Minimum conformance requirements p. 1192

7.2.5.4

Test description p. 1193

7.2.5.4.1	Initial conditions p. 1193
7.2.5.4.2	Test procedure p. 1193
7.2.5.4.3	Message contents p. 1194

7.2.5.5

Test requirement p. 1196

7.2.5A

E-UTRAN TDD - UE Timing Advance Adjustment Accuracy Test for SCell in sTAG for 20MHz +20MHz bandwidth p. 1198

7.2.5A.1

Test purpose p. 1198

7.2.5A.2

Test applicability p. 1198

7.2.5A.3

Minimum conformance requirements p. 1198

7.2.5A.4

Test description p. 1198

7.2.5A.4.1	Initial conditions p. 1198
7.2.5A.4.2	Test procedure p. 1198
7.2.5A.4.3	Message contents p. 1198

7.2.5A.5

Test requirement p. 1198

7.2.5B

E-UTRAN TDD - UE Timing Advance Adjustment Accuracy Test for SCell in sTAG for 20MHz +10MHz bandwidth p. 1199

7.2.5B.1

Test purpose p. 1199

7.2.5B.2

Test applicability p. 1199

7.2.5B.3

Minimum conformance requirements p. 1199

7.2.5B.4

Test description p. 1200

7.2.5B.4.1	Initial conditions p. 1200
7.2.5B.4.2	Test procedure p. 1200
7.2.5B.4.3	Message contents p. 1200

7.2.5B.5

Test requirement p. 1200

7.2.6

E-UTRAN FDD Timing Advance Adjustment Accuracy Test for CE UE in CEModeA p. 1201

7.2.6.1

Test purpose p. 1201

7.2.6.2

Test applicability p. 1201

7.2.6.3

Minimum conformance requirements p. 1201

7.2.6.4

Test description p. 1202

7.2.6.4.1	Initial conditions p. 1202
7.2.6.4.2	Test procedure p. 1202
7.2.6.4.3	Message contents p. 1203

7.2.6.5

Test requirement p. 1204

7.2.7

E-UTRAN HD-FDD UE Timing Advance Adjustment Accuracy Test for CE UE in CEModeA p. 1206

7.2.7.1

Test purpose p. 1206

7.2.7.2

Test applicability p. 1206

7.2.7.3

Minimum conformance requirements p. 1206

7.2.7.4

Test description p. 1206

7.2.7.4.1	Initial conditions p. 1206
7.2.7.4.2	Test procedure p. 1206
7.2.7.4.3	Message contents p. 1207

7.2.7.5

Test requirement p. 1207

7.2.8

E-UTRAN TDD Timing Advance Adjustment Accuracy Test for CE UE in CEModeA p. 1208

7.2.8.1

Test purpose p. 1208

7.2.8.2

Test applicability p. 1208

7.2.8.3

Minimum conformance requirements p. 1208

7.2.8.4

Test description p. 1208

7.2.8.4.1	Initial conditions p. 1208
7.2.8.4.2	Test procedure p. 1209
7.2.8.4.3	Message contents p. 1209

7.2.8.5

Test requirement p. 1209

7.2.9

HD-FDD UE Timing Advance Adjustment Accuracy Test for Category NB1 UE in Standalone Mode under Enhance Coverage p. 1210

7.2.9.1

Test Purpose p. 1210

7.2.9.2

Test applicability p. 1210

7.2.9.3

Minimum conformance requirements p. 1211

7.2.9.4

Test description p. 1211

7.2.9.4.1	Initial conditions p. 1211
7.2.9.4.2	Test procedure p. 1212
7.2.9.4.3	Message contents p. 1213

7.2.9.5

Test requirement p. 1213

7.2.10

E-UTRAN FDD UE Timing Advance Adjustment Accuracy Test for CE UE in CEModeB p. 1214

7.2.10.1

Test purpose p. 1214

7.2.10.2

Test applicability p. 1214

7.2.10.3

Minimum conformance requirements p. 1214

7.2.10.4

Test description p. 1215

7.2.10.4.1	Initial conditions p. 1215
7.2.10.4.2	Test procedure p. 1215
7.2.10.4.3	Message contents p. 1216

7.2.10.5

Test requirement p. 1216

7.2.11

E-UTRAN HD-FDD UE Timing Advance Adjustment Accuracy Test for CE UE in CEModeB p. 1217

7.2.11.1

Test purpose p. 1217

7.2.11.2

Test applicability p. 1218

7.2.11.3

Minimum conformance requirements p. 1218

7.2.11.4

Test description p. 1218

7.2.11.4.1	Initial conditions p. 1218
7.2.11.4.2	Test procedure p. 1218
7.2.11.4.3	Message contents p. 1218

7.2.11.5

Test requirement p. 1218

7.2.12

E-UTRAN TDD UE Timing Advance Adjustment Accuracy Test for CE UE in CEModeB p. 1219

7.2.12.1

Test purpose p. 1219

7.2.12.2

Test applicability p. 1220

7.2.12.3

Minimum conformance requirements p. 1220

7.2.12.4

Test description p. 1220

7.2.12.4.1	Initial conditions p. 1220
7.2.12.4.2	Test procedure p. 1220
7.2.12.4.3	Message contents p. 1220

7.2.12.5

Test requirement p. 1220

7.2.13

E-UTRAN FDD - UE Timing Advance Adjustment Accuracy Test for sTTI and ShortProcessingTime p. 1222

7.2.13.1

Test purpose p. 1222

7.2.13.2

Test applicability p. 1222

7.2.13.3

Minimum conformance requirements p. 1222

7.2.13.4

Test description p. 1222

7.2.13.4.1	Initial conditions p. 1222
7.2.13.4.2	Test procedure p. 1223
7.2.13.4.3	Message contents p. 1224

7.2.13.5

Test requirement p. 1226

7.2.14

E-UTRAN TDD - UE Timing Advance Adjustment Accuracy Test for sTTI and ShortProcessingTime p. 1227

7.2.14.1

Test purpose p. 1227

7.2.14.2

Test applicability p. 1227

7.2.14.3

Minimum conformance requirements p. 1227

7.2.14.4

Test description p. 1228

7.2.14.4.1	Initial conditions p. 1228
7.2.14.4.2	Test procedure p. 1228
7.2.14.4.3	Message contents p. 1229

7.2.14.5

Test requirement p. 1231

7.2.15

E-UTRAN TDD - TDD UE Timing Advance Adjustment Accuracy Test for UE Category NB1 in Standalone Mode under Enhanced Coverage p. 1232

7.2.15.1

Test purpose p. 1232

7.2.15.2

Test applicability p. 1232

7.2.15.3

Minimum conformance requirements p. 1232

7.2.15.4

Test description p. 1232

7.2.15.4.1	Initial conditions p. 1232
7.2.15.4.2	Test procedure p. 1233
7.2.15.4.3	Message contents p. 1233

7.2.15.5

Test requirement p. 1233

7.3

Radio Link Monitoring p. 1235

7.3.1

E-UTRAN FDD Radio Link Monitoring Test for Out-of-sync p. 1235

7.3.1.1

Test purpose p. 1235

7.3.1.2

Test applicability p. 1235

7.3.1.3

Minimum conformance requirements p. 1235

7.3.1.4

Test description p. 1235

7.3.1.4.1	Initial conditions p. 1236
7.3.1.4.2	Test procedure p. 1237
7.3.1.4.3	Message contents p. 1237

7.3.1.5

Test requirement p. 1239

7.3.1_1

E-UTRAN FDD Radio Link Monitoring Test for Out-of-sync with 4 Rx antenna ports p. 1241

7.3.1_1.1

Test purpose p. 1241

7.3.1_1.2

Test applicability p. 1241

7.3.1_1.3

Minimum conformance requirements p. 1241

7.3.1_1.4

Test description p. 1241

7.3.1_1.4.1	Initial conditions p. 1241
7.3.1_1.4.2	Test procedure p. 1241
7.3.1_1.4.3	Message contents p. 1242

7.3.1_1.5

Test requirement p. 1242

7.3.2

E-UTRAN FDD Radio Link Monitoring Test for In-sync p. 1244

7.3.2.1

Test purpose p. 1244

7.3.2.2

Test applicability p. 1244

7.3.2.3

Minimum conformance requirements p. 1244

7.3.2.4

Test description p. 1244

7.3.2.4.1	Initial conditions p. 1244
7.3.2.4.2	Test procedure p. 1246
7.3.2.4.3	Message contents p. 1246

7.3.2.5

Test requirement p. 1248

7.3.2_1

E-UTRAN FDD Radio Link Monitoring Test for In-sync with 4 Rx antenna ports p. 1248

7.3.2_1.1

Test purpose p. 1248

7.3.2_1.2

Test applicability p. 1249

7.3.2_1.3

Minimum conformance requirements p. 1249

7.3.2_1.4

Test description p. 1249

7.3.2_1.4.1	Initial conditions p. 1249
7.3.2_1.4.2	Test procedure p. 1249
7.3.2_1.4.3	Message contents p. 1249

7.3.2_1.5

Test requirement p. 1250

7.3.3

E-UTRAN TDD Radio Link Monitoring Test for Out-of-sync p. 1251

7.3.3.1

Test purpose p. 1251

7.3.3.2

Test applicability p. 1251

7.3.3.3

Minimum conformance requirements p. 1251

7.3.3.4

Test description p. 1251

7.3.3.4.1	Initial conditions p. 1251
7.3.3.4.2	Test procedure p. 1253
7.3.3.4.3	Message contents p. 1253

7.3.3.5

Test requirement p. 1255

7.3.3_1

E-UTRAN TDD Radio Link Monitoring Test for Out-of-sync with 4 Rx antenna ports p. 1257

7.3.3_1.1

Test purpose p. 1257

7.3.3_1.2

Test applicability p. 1257

7.3.3_1.3

Minimum conformance requirements p. 1257

7.3.3_1.4

Test description p. 1257

7.3.3_1.4.1	Initial conditions p. 1257
7.3.3_1.4.2	Test procedure p. 1257
7.3.3_1.4.3	Message contents p. 1258

7.3.3_1.5

Test requirement p. 1258

7.3.4

E-UTRAN TDD Radio Link Monitoring Test for In-sync p. 1260

7.3.4.1

Test purpose p. 1260

7.3.4.2

Test applicability p. 1260

7.3.4.3

Minimum conformance requirements p. 1260

7.3.4.4

Test description p. 1260

7.3.4.4.1	Initial conditions p. 1260
7.3.4.4.2	Test procedure p. 1262
7.3.4.4.3	Message contents p. 1262

7.3.4.5

Test requirement p. 1264

7.3.4_1

E-UTRAN TDD Radio Link Monitoring Test for In-sync with 4 Rx antenna ports p. 1265

7.3.4_1.1

Test purpose p. 1265

7.3.4_1.2

Test applicability p. 1265

7.3.4_1.3

Minimum conformance requirements p. 1265

7.3.4_1.4

Test description p. 1265

7.3.4_1.4.1	Initial conditions p. 1265
7.3.4_1.4.2	Test procedure p. 1265
7.3.4_1.4.3	Message contents p. 1265

7.3.4_1.5

Test requirement p. 1266

7.3.5

E-UTRAN FDD Radio Link Monitoring Test for Out-of-sync in DRX p. 1267

7.3.5.1

Test purpose p. 1267

7.3.5.2

Test applicability p. 1267

7.3.5.3

Minimum conformance requirements p. 1267

7.3.5.4

Test description p. 1267

7.3.5.4.1	Initial conditions p. 1268
7.3.5.4.2	Test procedure p. 1269
7.3.5.4.3	Message contents p. 1270

7.3.5.5

Test requirement p. 1272

7.3.5_1

E-UTRAN FDD Radio Link Monitoring Test for Out-of-sync in DRX with 4 Rx antenna ports p. 1274

7.3.5_1.1

Test purpose p. 1274

7.3.5_1.2

Test applicability p. 1274

7.3.5_1.3

Minimum conformance requirements p. 1274

7.3.5_1.4

Test description p. 1274

7.3.5_1.4.1	Initial conditions p. 1274
7.3.5_1.4.2	Test procedure p. 1274
7.3.5_1.4.3	Message contents p. 1274

7.3.5_1.5

Test requirement p. 1275

7.3.6

E-UTRAN FDD Radio Link Monitoring Test for In-sync in DRX p. 1276

7.3.6.1

Test purpose p. 1276

7.3.6.2

Test applicability p. 1276

7.3.6.3

Minimum conformance requirements p. 1276

7.3.6.4

Test description p. 1277

7.3.6.4.1	Initial conditions p. 1277
7.3.6.4.2	Test procedure p. 1279
7.3.6.4.3	Message contents p. 1279

7.3.6.5

Test requirement p. 1281

7.3.6_1

E-UTRAN FDD Radio Link Monitoring Test for In-sync in DRX with 4 Rx antenna ports p. 1282

7.3.6_1.1

Test purpose p. 1282

7.3.6_1.2

Test applicability p. 1282

7.3.6_1.3

Minimum conformance requirements p. 1282

7.3.6_1.4

Test description p. 1282

7.3.6_1.4.1	Initial conditions p. 1282
7.3.6_1.4.2	Test procedure p. 1283
7.3.6_1.4.3	Message contents p. 1283

7.3.6_1.5

Test requirement p. 1283

7.3.7

E-UTRAN TDD Radio Link Monitoring Test for Out-of-sync in DRX p. 1284

7.3.7.1

Test purpose p. 1284

7.3.7.2

Test applicability p. 1284

7.3.7.3

Minimum conformance requirements p. 1284

7.3.7.4

Test description p. 1285

7.3.7.4.1	Initial conditions p. 1285
7.3.7.4.2	Test procedure p. 1286
7.3.7.4.3	Message contents p. 1287

7.3.7.5

Test requirement p. 1291

7.3.7_1

E-UTRAN TDD Radio Link Monitoring Test for Out-of-sync in DRX with 4 Rx antenna ports p. 1292

7.3.7_1.1

Test purpose p. 1292

7.3.7_1.2

Test applicability p. 1292

7.3.7_1.3

Minimum conformance requirements p. 1292

7.3.7_1.4

Test description p. 1292

7.3.7_1.4.1	Initial conditions p. 1292
7.3.7_1.4.2	Test procedure p. 1293
7.3.7_1.4.3	Message contents p. 1293

7.3.7_1.5

Test requirement p. 1293

7.3.8

E-UTRAN TDD Radio Link Monitoring Test for In-sync in DRX p. 1295

7.3.8.1

Test purpose p. 1295

7.3.8.2

Test applicability p. 1295

7.3.8.3

Minimum conformance requirements p. 1295

7.3.8.4

Test description p. 1295

7.3.8.4.1	Initial conditions p. 1296
7.3.8.4.2	Test procedure p. 1297
7.3.8.4.3	Message contents p. 1298

7.3.8.5

Test requirement p. 1300

7.3.8_1

E-UTRAN TDD Radio Link Monitoring Test for In-sync in DRX with 4 Rx antenna ports p. 1301

7.3.8_1.1

Test purpose p. 1301

7.3.8_1.2

Test applicability p. 1301

7.3.8_1.3

Minimum conformance requirements p. 1301

7.3.8_1.4

Test description p. 1301

7.3.8_1.4.1	Initial conditions p. 1301
7.3.8_1.4.2	Test procedure p. 1302
7.3.8_1.4.3	Message contents p. 1302

7.3.8_1.5

Test requirement p. 1302

7.3.9

E-UTRAN FDD Radio Link Monitoring Test for Out-of-sync under Time Domain Measurement Resource Restriction with Non MBSFN ABS (eICIC) p. 1303

7.3.9.1

Test purpose p. 1303

7.3.9.2

Test applicability p. 1303

7.3.9.3

Minimum conformance requirements p. 1303

7.3.9.4

Test description p. 1304

7.3.9.4.1	Initial conditions p. 1304
7.3.9.4.2	Test procedure p. 1305
7.3.9.4.3	Message contents p. 1306

7.3.9.5

Test requirements p. 1308

7.3.10

E-UTRAN TDD Radio Link Monitoring Test for Out-of-sync under Time Domain Measurement Resource Restriction with Non MBSFN ABS (eICIC) p. 1309

7.3.10.1

Test purpose p. 1309

7.3.10.2

Test applicability p. 1309

7.3.10.3

Minimum conformance requirements p. 1309

7.3.10.4

Test description p. 1310

7.3.10.4.1	Initial conditions p. 1310
7.3.10.4.2	Test procedure p. 1311
7.3.10.4.3	Message contents p. 1312

7.3.10.5

Test requirements p. 1314

7.3.11

E-UTRAN FDD Radio Link Monitoring Test for In-sync under Time Domain Measurement Resource Restriction with Non MBSFN ABS (eICIC) p. 1315

7.3.11.1

Test purpose p. 1315

7.3.11.2

Test applicability p. 1315

7.3.11.3

Minimum conformance requirements p. 1315

7.3.11.4

Test description p. 1315

7.3.11.4.1	Initial conditions p. 1316
7.3.11.4.2	Test procedure p. 1317
7.3.11.4.3	Message contents p. 1318

7.3.11.5

Test requirements p. 1319

7.3.12

E-UTRAN TDD Radio Link Monitoring Test for In-sync under Time Domain Measurement Resource Restriction with Non MBSFN ABS (eICIC) p. 1320

7.3.12.1

Test purpose p. 1320

7.3.12.2

Test applicability p. 1320

7.3.12.3

Minimum conformance requirements p. 1320

7.3.12.4

Test description p. 1321

7.3.12.4.1	Initial conditions p. 1321
7.3.12.4.2	Test procedure p. 1323
7.3.12.4.3	Message contents p. 1323

7.3.12.5

Test requirements p. 1325

7.3.13

E-UTRAN FDD Radio Link Monitoring Test for Out-of-sync under Time Domain Measurement Resource Restriction with MBSFN ABS (eICIC) p. 1326

7.3.13.1

Test purpose p. 1326

7.3.13.2

Test applicability p. 1326

7.3.13.3

Minimum conformance requirements p. 1326

7.3.13.4

Test description p. 1326

7.3.13.4.1	Initial conditions p. 1327
7.3.13.4.2	Test procedure p. 1328
7.3.13.4.3	Message contents p. 1329

7.3.13.5

Test requirements p. 1331

7.3.14

E-UTRAN TDD Radio Link Monitoring Test for Out-of-sync under Time Domain Measurement Resource Restriction with MBSFN ABS (eICIC) p. 1332

7.3.14.1

Test purpose p. 1332

7.3.14.2

Test applicability p. 1332

7.3.14.3

Minimum conformance requirements p. 1332

7.3.14.4

Test description p. 1332

7.3.14.4.1	Initial conditions p. 1333
7.3.14.4.2	Test procedure p. 1334
7.3.14.4.3	Message contents p. 1335

7.3.14.5

Test requirements p. 1338

7.3.15

E-UTRAN FDD Radio Link Monitoring Test for In-sync under Time Domain Measurement Resource Restriction with MBSFN ABS (eICIC) p. 1339

7.3.15.1

Test purpose p. 1339

7.3.15.2

Test applicability p. 1339

7.3.15.3

Minimum conformance requirements p. 1339

7.3.15.4

Test description p. 1339

7.3.15.4.1	Initial conditions p. 1340
7.3.15.4.2	Test procedure p. 1341
7.3.15.4.3	Message contents p. 1342

7.3.15.5

Test requirements p. 1344

7.3.16

E-UTRAN TDD Radio Link Monitoring Test for In-sync under Time Domain Measurement Resource Restriction with MBSFN ABS (eICIC) p. 1344

7.3.16.1

Test purpose p. 1344

7.3.16.2

Test applicability p. 1345

7.3.16.3

Minimum conformance requirements p. 1345

7.3.16.4

Test description p. 1345

7.3.16.4.1	Initial conditions p. 1345
7.3.16.4.2	Test procedure p. 1347
7.3.16.4.3	Message contents p. 1348

7.3.16.5

Test requirements p. 1350

7.3.17

E-UTRAN FDD Radio Link Monitoring Test for Out-of-sync under Time Domain Measurement Resource Restriction with CRS assistance information and Non MBSFN ABS (feICIC) p. 1351

7.3.17.1

Test purpose p. 1351

7.3.17.2

Test applicability p. 1351

7.3.17.3

Minimum conformance requirements p. 1351

7.3.17.4

Test description p. 1351

7.3.17.4.1	Initial conditions p. 1352
7.3.17.4.2	Test procedure p. 1353
7.3.17.4.3	Message contents p. 1354

7.3.17.5

Test requirements p. 1357

7.3.18

E-UTRAN TDD Radio Link Monitoring Test for Out-of-sync under Time Domain Measurement Resource Restriction with CRS assistance information and Non MBSFN ABS (feICIC) p. 1358

7.3.18.1

Test purpose p. 1358

7.3.18.2

Test applicability p. 1358

7.3.18.3

Minimum conformance requirements p. 1358

7.3.18.4

Test description p. 1358

7.3.18.4.1	Initial conditions p. 1359
7.3.18.4.2	Test procedure p. 1360
7.3.18.4.3	Message contents p. 1361

7.3.18.5

Test requirements p. 1364

7.3.19

E-UTRAN FDD Radio Link Monitoring Test for In-sync under Time Domain Measurement Resource Restriction with CRS assistance information and Non MBSFN ABS (feICIC) p. 1365

7.3.19.1

Test purpose p. 1365

7.3.19.2

Test applicability p. 1365

7.3.19.3

Minimum conformance requirements p. 1365

7.3.19.4

Test description p. 1365

7.3.19.4.1	Initial conditions p. 1366
7.3.19.4.2	Test procedure p. 1368
7.3.19.4.3	Message contents p. 1368

7.3.19.5

Test requirements p. 1371

7.3.20

E-UTRAN TDD Radio Link Monitoring Test for In-sync under Time Domain Measurement Resource Restriction with CRS assistance information and Non MBSFN ABS (feICIC) p. 1372

7.3.20.1

Test purpose p. 1372

7.3.20.2

Test applicability p. 1372

7.3.20.3

Minimum conformance requirements p. 1372

7.3.20.4

Test description p. 1372

7.3.20.4.1	Initial conditions p. 1373
7.3.20.4.2	Test procedure p. 1375
7.3.20.4.3	Message contents p. 1376

7.3.20.5

Test requirements p. 1378

7.3.21

E-UTRAN FDD Radio Link Monitoring Test for In-sync under Time Domain Measurement Resource Restriction with CRS assistance information and MBSFN ABS (feICIC) p. 1379

7.3.21.1

Test purpose p. 1379

7.3.21.2

Test applicability p. 1379

7.3.21.3

Minimum conformance requirements p. 1379

7.3.21.4

Test description p. 1380

7.3.21.4.1	Initial conditions p. 1380
7.3.21.4.2	Test procedure p. 1382
7.3.21.4.3	Message contents p. 1383

7.3.21.5

Test requirements p. 1386

7.3.22

E-UTRAN TDD Radio Link Monitoring Test for In-sync under Time Domain Measurement Resource Restriction with CRS assistance information and MBSFN ABS (feICIC) p. 1387

7.3.22.1

Test purpose p. 1387

7.3.22.2

Test applicability p. 1387

7.3.22.3

Minimum conformance requirements p. 1387

7.3.22.4

Test description p. 1387

7.3.22.4.1	Initial conditions p. 1388
7.3.22.4.2	Test procedure p. 1390
7.3.22.4.3	Message contents p. 1391

7.3.22.5

Test requirements p. 1394

7.3.23

E-UTRAN FDD Radio Link Monitoring Test for Out-of-sync for 5MHz Bandwidth p. 1395

7.3.23.1

Test purpose p. 1395

7.3.23.2

Test applicability p. 1395

7.3.23.3

Minimum conformance requirements p. 1395

7.3.23.4

Test description p. 1395

7.3.23.4.1	Initial conditions p. 1395
7.3.23.4.2	Test procedure p. 1396
7.3.23.4.3	Message contents p. 1396

7.3.23.5

Test requirement p. 1397

7.3.23_1

E-UTRAN FDD Radio Link Monitoring Test for Out-of-sync for 5MHz Bandwidth with 4 Rx antenna ports p. 1398

7.3.23_1.1

Test purpose p. 1398

7.3.23_1.2

Test applicability p. 1398

7.3.23_1.3

Minimum conformance requirements p. 1398

7.3.23_1.4

Test description p. 1398

7.3.23_1.4.1	Initial conditions p. 1398
7.3.23_1.4.2	Test procedure p. 1399
7.3.23_1.4.3	Message contents p. 1399

7.3.23_1.5

Test requirement p. 1399

7.3.24

E-UTRAN FDD Radio Link Monitoring Test for In-sync for 5MHz Bandwidth p. 1399

7.3.24.1

Test purpose p. 1399

7.3.24.2

Test applicability p. 1399

7.3.24.3

Minimum conformance requirements p. 1399

7.3.24.4

Test description p. 1399

7.3.24.4.1	Initial conditions p. 1400
7.3.24.4.2	Test procedure p. 1401
7.3.24.4.3	Message contents p. 1401

7.3.24.5

Test requirement p. 1401

7.3.25

E-UTRAN FDD Radio Link Monitoring Test for In-sync in DRX for 5MHz Bandwidth p. 1401

7.3.25.1

Test purpose p. 1401

7.3.25.2

Test applicability p. 1401

7.3.25.3

Minimum conformance requirements p. 1401

7.3.25.4

Test description p. 1401

7.3.25.4.1	Initial conditions p. 1401
7.3.25.4.2	Test procedure p. 1402
7.3.25.4.3	Message contents p. 1402

7.3.25.5

Test requirement p. 1402

7.3.26

E-UTRAN FD-FDD Radio Link Monitoring Test for Out-of-sync for UE category 0 p. 1403

7.3.26.1

Test purpose p. 1403

7.3.26.2

Test applicability p. 1403

7.3.26.3

Minimum conformance requirements p. 1403

7.3.26.4

Test description p. 1403

7.3.26.4.1	Initial conditions p. 1404
7.3.26.4.2	Test procedure p. 1404
7.3.26.4.3	Message contents p. 1405

7.3.26.5

Test requirement p. 1406

7.3.26_2

E-UTRAN FD-FDD Radio Link Monitoring Test for Out-of-sync for UE Category 1bis p. 1407

7.3.26_2.1

Test purpose p. 1407

7.3.26_2.2

Test applicability p. 1407

7.3.26_2.3

Minimum conformance requirements p. 1407

7.3.26_2.4

Test description p. 1407

7.3.26_2.4.1	Initial conditions p. 1407
7.3.26_2.4.2	Test procedure p. 1408
7.3.26_2.4.3	Message contents p. 1408

7.3.26_2.5

Test requirement p. 1408

7.3.27

E-UTRAN FD-FDD Radio Link Monitoring Test for In-sync for UE category 0 p. 1409

7.3.27.1

Test purpose p. 1409

7.3.27.2

Test applicability p. 1409

7.3.27.3

Minimum conformance requirements p. 1409

7.3.27.4

Test description p. 1409

7.3.27.4.1	Initial conditions p. 1410
7.3.27.4.2	Test procedure p. 1411
7.3.27.4.3	Message contents p. 1411

7.3.27.5

Test requirement p. 1413

7.3.27_2

E-UTRAN FD-FDD Radio Link Monitoring Test for In-sync for UE Category 1bis p. 1413

7.3.27_2.1

Test purpose p. 1413

7.3.27_2.2

Test applicability p. 1414

7.3.27_2.3

Minimum conformance requirements p. 1414

7.3.27_2.4

Test description p. 1414

7.3.27_2.4.1	Initial conditions p. 1414
7.3.27_2.4.2	Test procedure p. 1414
7.3.27_2.4.3	Message contents p. 1414

7.3.27_2.5

Test requirement p. 1414

7.3.28

E-UTRAN FD-FDD Radio Link Monitoring Test for Out-of-sync in DRX for UE category 0 p. 1415

7.3.28.1

Test purpose p. 1415

7.3.28.2

Test applicability p. 1415

7.3.28.3

Minimum conformance requirements p. 1416

7.3.28.4

Test description p. 1416

7.3.28.4.1	Initial conditions p. 1417
7.3.28.4.2	Test procedure p. 1418
7.3.28.4.3	Message contents p. 1418

7.3.28.5

Test requirement p. 1420

7.3.28_2

E-UTRAN FD-FDD Radio Link Monitoring Test for Out-of-sync in DRX for UE Category 1bis p. 1422

7.3.28_2.1

Test purpose p. 1422

7.3.28_2.2

Test applicability p. 1422

7.3.28_2.3

Minimum conformance requirements p. 1422

7.3.28_2.4

Test description p. 1422

7.3.28_2.4.1	Initial conditions p. 1422
7.3.28_2.4.2	Test procedure p. 1422
7.3.28_2.4.3	Message contents p. 1422

7.3.28_2.5

Test requirement p. 1423

7.3.29

E-UTRAN FD-FDD Radio Link Monitoring Test for In-sync in DRX for UE category 0 p. 1424

7.3.29.1

Test purpose p. 1424

7.3.29.2

Test applicability p. 1424

7.3.29.3

Minimum conformance requirements p. 1424

7.3.29.4

Test description p. 1425

7.3.29.4.1	Initial conditions p. 1425
7.3.29.4.2	Test procedure p. 1426
7.3.29.4.3	Message contents p. 1427

7.3.29.5

Test requirement p. 1429

7.3.29_2

E-UTRAN FD-FDD Radio Link Monitoring Test for In-sync in DRX for UE Category 1bis p. 1430

7.3.29_2.1

Test purpose p. 1430

7.3.29_2.2

Test applicability p. 1430

7.3.29_2.3

Minimum conformance requirements p. 1430

7.3.29_2.4

Test description p. 1430

7.3.29_2.4.1	Initial conditions p. 1430
7.3.29_2.4.2	Test procedure p. 1431
7.3.29_2.4.3	Message contents p. 1431

7.3.29_2.5

Test requirement p. 1431

7.3.30

E-UTRAN HD-FDD Radio Link Monitoring Test for Out-of-sync for UE category 0 p. 1432

7.3.30.1

Test purpose p. 1432

7.3.30.2

Test applicability p. 1432

7.3.30.3

Minimum conformance requirements p. 1433

7.3.30.4

Test description p. 1433

7.3.30.4.1	Initial conditions p. 1433
7.3.30.4.2	Test procedure p. 1434
7.3.30.4.3	Message contents p. 1435

7.3.30.5

Test requirement p. 1436

7.3.31

E-UTRAN HD-FDD Radio Link Monitoring Test for In-sync for UE category 0 p. 1437

7.3.31.1

Test purpose p. 1437

7.3.31.2

Test applicability p. 1437

7.3.31.3

Minimum conformance requirements p. 1437

7.3.31.4

Test description p. 1437

7.3.31.4.1	Initial conditions p. 1438
7.3.31.4.2	Test procedure p. 1439
7.3.31.4.3	Message contents p. 1439

7.3.31.5

Test requirement p. 1441

7.3.32

E-UTRAN HD-FDD Radio Link Monitoring Test for Out-of-sync in DRX for UE category 0 p. 1441

7.3.32.1

Test purpose p. 1441

7.3.32.2

Test applicability p. 1442

7.3.32.3

Minimum conformance requirements p. 1442

7.3.32.4

Test description p. 1442

7.3.32.4.1	Initial conditions p. 1443
7.3.32.4.2	Test procedure p. 1444
7.3.32.4.3	Message contents p. 1444

7.3.32.5

Test requirement p. 1446

7.3.33

E-UTRAN HD-FDD Radio Link Monitoring Test for In-sync in DRX for UE category 0 p. 1448

7.3.33.1

Test purpose p. 1448

7.3.33.2

Test applicability p. 1448

7.3.33.3

Minimum conformance requirements p. 1448

7.3.33.4

Test description p. 1449

7.3.33.4.1	Initial conditions p. 1449
7.3.33.4.2	Test procedure p. 1450
7.3.33.4.3	Message contents p. 1451

7.3.33.5

Test requirement p. 1453

7.3.34

E-UTRAN TDD Radio Link Monitoring Test for Out-of-sync for UE category 0 p. 1454

7.3.34.1

Test purpose p. 1454

7.3.34.2

Test applicability p. 1454

7.3.34.3

Minimum conformance requirements p. 1454

7.3.34.4

Test description p. 1455

7.3.34.4.1	Initial conditions p. 1455
7.3.34.4.2	Test procedure p. 1456
7.3.34.4.3	Message contents p. 1456

7.3.34.5

Test requirement p. 1458

7.3.34_2

E-UTRAN TDD Radio Link Monitoring Test for Out-of-sync for UE Category 1bis p. 1459

7.3.34_2.1

Test purpose p. 1459

7.3.34_2.2

Test applicability p. 1459

7.3.34_2.3

Minimum conformance requirements p. 1459

7.3.34_2.4

Test description p. 1459

7.3.34_2.4.1	Initial conditions p. 1459
7.3.34_2.4.2	Test procedure p. 1459
7.3.34_2.4.3	Message contents p. 1459

7.3.34_2.5

Test requirement p. 1460

7.3.35

E-UTRAN TDD Radio Link Monitoring Test for In-sync for UE category 0 p. 1461

7.3.35.1

Test purpose p. 1461

7.3.35.2

Test applicability p. 1461

7.3.35.3

Minimum conformance requirements p. 1461

7.3.35.4

Test description p. 1461

7.3.35.4.1	Initial conditions p. 1462
7.3.35.4.2	Test procedure p. 1463
7.3.35.4.3	Message contents p. 1463

7.3.35.5

Test requirement p. 1464

7.3.35_2

E-UTRAN TDD Radio Link Monitoring Test for In-sync for UE Category 1bis p. 1465

7.3.35_2.1

Test purpose p. 1465

7.3.35_2.2

Test applicability p. 1465

7.3.35_2.3

Minimum conformance requirements p. 1465

7.3.35_2.4

Test description p. 1465

7.3.35_2.4.1	Initial conditions p. 1465
7.3.35_2.4.2	Test procedure p. 1466
7.3.35_2.4.3	Message contents p. 1466

7.3.35_2.5

Test requirement p. 1466

7.3.36

E-UTRAN TDD Radio Link Monitoring Test for Out-of-sync in DRX for UE category 0 p. 1467

7.3.36.1

Test purpose p. 1467

7.3.36.2

Test applicability p. 1467

7.3.36.3

Minimum conformance requirements p. 1467

7.3.36.4

Test description p. 1468

7.3.36.4.1	Initial conditions p. 1468
7.3.36.4.2	Test procedure p. 1469
7.3.36.4.3	Message contents p. 1470

7.3.36.5

Test requirement p. 1472

7.3.36_2

E-UTRAN TDD Radio Link Monitoring Test for Out-of-sync in DRX for UE Category 1bis p. 1473

7.3.36_2.1

Test purpose p. 1473

7.3.36_2.2

Test applicability p. 1473

7.3.36_2.3

Minimum conformance requirements p. 1473

7.3.36_2.4

Test description p. 1473

7.3.36_2.4.1	Initial conditions p. 1474
7.3.36_2.4.2	Test procedure p. 1474
7.3.36_2.4.3	Message contents p. 1474

7.3.36_2.5

Test requirement p. 1474

7.3.37

E-UTRAN TDD Radio Link Monitoring Test for In-sync in DRX for UE category 0 p. 1476

7.3.37.1

Test purpose p. 1476

7.3.37.2

Test applicability p. 1476

7.3.37.3

Minimum conformance requirements p. 1476

7.3.37.4

Test description p. 1477

7.3.37.4.1	Initial conditions p. 1477
7.3.37.4.2	Test procedure p. 1478
7.3.37.4.3	Message contents p. 1479

7.3.37.5

Test requirement p. 1481

7.3.37_2

E-UTRAN TDD Radio Link Monitoring Test for In-sync in DRX for UE Category 1bis p. 1482

7.3.37_2.1

Test purpose p. 1482

7.3.37_2.2

Test applicability p. 1482

7.3.37_2.3

Minimum conformance requirements p. 1482

7.3.37_2.4

Test description p. 1482

7.3.37_2.4.1	Initial conditions p. 1482
7.3.37_2.4.2	Test procedure p. 1483
7.3.37_2.4.3	Message contents p. 1483

7.3.37_2.5

Test requirement p. 1483

7.3.38

E-UTRAN FDD-FDD DC Radio Link Monitoring Test for Out-of-sync in DRX in synchronous DC p. 1484

7.3.38.1

Test purpose p. 1484

7.3.38.2

Test applicability p. 1484

7.3.38.3

Minimum conformance requirements p. 1485

7.3.38.4

Test description p. 1485

7.3.38.4.1	Initial conditions p. 1486
7.3.38.4.2	Test procedure p. 1487
7.3.38.4.3	Message contents p. 1487

7.3.38.5

Test requirement p. 1490

7.3.38_1

E-UTRAN FDD-FDD DC Radio Link Monitoring Test for Out-of-sync in DRX in synchronous DC with 4 Rx antenna ports p. 1492

7.3.38_1.1

Test purpose p. 1492

7.3.38_1.2

Test applicability p. 1492

7.3.38_1.3

Minimum conformance requirements p. 1492

7.3.38_1.4

Test description p. 1492

7.3.38_1.4.1	Initial conditions p. 1492
7.3.38_1.4.2	Test procedure p. 1492
7.3.38_1.4.3	Message contents p. 1492

7.3.38_1.5

Test requirement p. 1493

7.3.39

E-UTRAN FDD-FDD DC Radio Link Monitoring Test for Out-of-sync in DRX in asynchronous DC p. 1494

7.3.39.1

Test purpose p. 1494

7.3.39.2

Test applicability p. 1494

7.3.39.3

Minimum conformance requirements p. 1494

7.3.39.4

Test description p. 1495

7.3.39.4.1	Initial conditions p. 1495
7.3.39.4.2	Test procedure p. 1496
7.3.39.4.3	Message contents p. 1497

7.3.39.5

Test requirement p. 1497

7.3.39_1

E-UTRAN FDD-FDD DC Radio Link Monitoring Test for Out-of-sync in DRX in asynchronous DC with 4 Rx antenna ports p. 1498

7.3.39_1.1

Test purpose p. 1498

7.3.39_1.2

Test applicability p. 1498

7.3.39_1.3

Minimum conformance requirements p. 1499

7.3.39_1.4

Test description p. 1499

7.3.39_1.4.1	Initial conditions p. 1499
7.3.39_1.4.2	Test procedure p. 1499
7.3.39_1.4.3	Message contents p. 1499

7.3.39_1.5

Test requirement p. 1499

7.3.40

E-UTRAN TDD-TDD DC Radio Link Monitoring Test for Out-of-sync in DRX in synchronous DC p. 1501

7.3.40.1

Test purpose p. 1501

7.3.40.2

Test applicability p. 1501

7.3.40.3

Minimum conformance requirements p. 1501

7.3.40.4

Test description p. 1502

7.3.40.4.1	Initial conditions p. 1502
7.3.40.4.2	Test procedure p. 1503
7.3.40.4.3	Message contents p. 1504

7.3.40.5

Test requirement p. 1507

7.3.41

E-UTRAN FDD-FDD Radio Link Monitoring Test for In-sync in DRX in synchronous dual connectivity p. 1508

7.3.41.1

Test purpose p. 1508

7.3.41.2

Test applicability p. 1508

7.3.41.3

Minimum conformance requirements p. 1508

7.3.41.4

Test description p. 1509

7.3.41.4.1	Initial conditions p. 1509
7.3.41.4.2	Test procedure p. 1511
7.3.41.4.3	Message contents p. 1511

7.3.41.5

Test requirement p. 1514

7.3.42

E-UTRAN FDD-FDD DC Radio Link Monitoring Test for In-sync in DRX in asynchronous DC p. 1515

7.3.42.1

Test purpose p. 1515

7.3.42.2

Test applicability p. 1515

7.3.42.3

Minimum conformance requirements p. 1515

7.3.42.4

Test description p. 1516

7.3.42.4.1	Initial conditions p. 1517
7.3.42.4.2	Test procedure p. 1518
7.3.42.4.3	Message contents p. 1518

7.3.42.5

Test requirement p. 1519

7.3.43

E-UTRAN TDD-TDD Radio Link Monitoring Test for In-sync in DRX in synchronous dual connectivity p. 1520

7.3.43.1

Test purpose p. 1520

7.3.43.2

Test applicability p. 1520

7.3.43.3

Minimum conformance requirements p. 1520

7.3.43.4

Test description p. 1521

7.3.43.4.1	Initial conditions p. 1521
7.3.43.4.2	Test procedure p. 1522
7.3.43.4.3	Message contents p. 1523

7.3.43.5

Test requirement p. 1525

7.3.44

E-UTRAN TDD-FDD DC Radio Link Monitoring Test for Out-of-sync in DRX in synchronous DC with PCell in FDD p. 1527

7.3.44.1

Test purpose p. 1527

7.3.44.2

Test applicability p. 1527

7.3.44.3

Minimum conformance requirements p. 1527

7.3.44.4

Test description p. 1528

7.3.44.4.1	Initial conditions p. 1528
7.3.44.4.2	Test procedure p. 1529
7.3.44.4.3	Message contents p. 1530

7.3.44.5

Test requirement p. 1533

7.3.45

E-UTRAN TDD-FDD DC Radio Link Monitoring Test for Out-of-sync in DRX in synchronous DC with PCell in TDD p. 1534

7.3.45.1

Test purpose p. 1534

7.3.45.2

Test applicability p. 1534

7.3.45.3

Minimum conformance requirements p. 1534

7.3.45.4

Test description p. 1535

7.3.45.4.1	Initial conditions p. 1535
7.3.45.4.2	Test procedure p. 1536
7.3.45.4.3	Message contents p. 1537

7.3.45.5

Test requirement p. 1540

7.3.46

E-UTRAN TDD-FDD Radio Link Monitoring Test for In-sync in DRX for PSCell in synchronous DC with PCell in FDD p. 1542

7.3.46.1

Test purpose p. 1542

7.3.46.2

Test applicability p. 1542

7.3.46.3

Minimum conformance requirements p. 1542

7.3.46.4

Test description p. 1542

7.3.46.4.1	Initial conditions p. 1543
7.3.46.4.2	Test procedure p. 1544
7.3.46.4.3	Message contents p. 1545

7.3.46.5

Test requirement p. 1548

7.3.47

E-UTRAN TDD-FDD Radio Link Monitoring Test for In-sync in DRX for PSCell in synchronous DC with PCell in TDD p. 1549

7.3.47.1

Test purpose p. 1549

7.3.47.2

Test applicability p. 1549

7.3.47.3

Minimum conformance requirements p. 1549

7.3.47.4

Test description p. 1550

7.3.47.4.1	Initial conditions p. 1550
7.3.47.4.2	Test procedure p. 1552
7.3.47.4.3	Message contents p. 1552

7.3.47.5

Test requirement p. 1555

7.3.48

E-UTRAN FD-FDD Radio Link Monitoring Test for Out-of-sync for CE UE in CEMode A p. 1557

7.3.48.1

Test purpose p. 1557

7.3.48.2

Test applicability p. 1557

7.3.48.3

Minimum conformance requirements p. 1557

7.3.48.4

Test description p. 1557

7.3.48.4.1	Initial conditions p. 1558
7.3.48.4.2	Test procedure p. 1559
7.3.48.4.3	Message contents p. 1559

7.3.48.5

Test requirement p. 1561

7.3.49

E-UTRAN FD-FDD Radio Link Monitoring Test for In-Sync for CE UE in CEModeA p. 1562

7.3.49.1

Test purpose p. 1562

7.3.49.2

Test applicability p. 1562

7.3.49.3

Minimum conformance requirements p. 1562

7.3.49.4

Test description p. 1562

7.3.49.4.1	Initial conditions p. 1563
7.3.49.4.2	Test procedure p. 1564
7.3.49.4.3	Message contents p. 1564

7.3.49.5

Test requirement p. 1566

7.3.50

E-UTRAN FD-FDD Radio Link Monitoring Test for Out-of-sync in DRX for CE UE in CEModeA p. 1566

7.3.50.1

Test purpose p. 1566

7.3.50.2

Test applicability p. 1567

7.3.50.3

Minimum conformance requirements p. 1567

7.3.50.4

Test description p. 1568

7.3.50.4.1	Initial conditions p. 1568
7.3.50.4.2	Test procedure p. 1569
7.3.50.4.3	Message contents p. 1569

7.3.50.5

Test requirement p. 1571

7.3.51

E-UTRAN FD-FDD Radio Link Monitoring Test for In-sync in DRX for CE UE in CEMode A p. 1572

7.3.51.1

Test purpose p. 1572

7.3.51.2

Test applicability p. 1573

7.3.51.3

Minimum conformance requirements p. 1573

7.3.51.4

Test description p. 1574

7.3.51.4.1	Initial conditions p. 1574
7.3.51.4.2	Test procedure p. 1575
7.3.51.4.3	Message contents p. 1576

7.3.51.5

Test requirement p. 1578

7.3.52

E-UTRAN HD-FDD Radio Link Monitoring Test for Out-of-sync for CE UE in CEModeA p. 1579

7.3.52.1

Test purpose p. 1579

7.3.52.2

Test applicability p. 1579

7.3.52.3

Minimum conformance requirements p. 1579

7.3.52.4

Test description p. 1580

7.3.52.4.1	Initial conditions p. 1580
7.3.52.4.2	Test procedure p. 1581
7.3.52.4.3	Message contents p. 1581

7.3.52.5

Test requirement p. 1583

7.3.53

E-UTRAN HD-FDD Radio Link Monitoring Test for In-sync for CE UE in CEModeA p. 1584

7.3.53.1

Test purpose p. 1584

7.3.53.2

Test applicability p. 1584

7.3.53.3

Minimum conformance requirements p. 1584

7.3.53.4

Test description p. 1584

7.3.53.4.1	Initial conditions p. 1585
7.3.53.4.2	Test procedure p. 1586
7.3.53.4.3	Message contents p. 1586

7.3.53.5

Test requirement p. 1588

7.3.54

E-UTRAN HD-FDD Radio Link Monitoring Test for Out-of-sync in DRX for CE UE in CEmodeA p. 1589

7.3.54.1

Test purpose p. 1589

7.3.54.2

Test applicability p. 1589

7.3.54.3

Minimum conformance requirements p. 1589

7.3.54.4

Test description p. 1590

7.3.54.4.1	Initial conditions p. 1590
7.3.54.4.2	Test procedure p. 1591
7.3.54.4.3	Message contents p. 1592

7.3.54.5

Test requirement p. 1594

7.3.55

E-UTRAN HD-FDD Radio Link Monitoring Test for In-sync in DRX for CE UE in CEModeA p. 1595

7.3.55.1

Test purpose p. 1595

7.3.55.2

Test applicability p. 1595

7.3.55.3

Minimum conformance requirements p. 1595

7.3.55.4

Test description p. 1596

7.3.55.4.1	Initial conditions p. 1597
7.3.55.4.2	Test procedure p. 1598
7.3.55.4.3	Message contents p. 1598

7.3.55.5

Test requirement p. 1600

7.3.56

E-UTRAN TDD Radio Link Monitoring Test for Out-of-sync for CE UE in CEModeA p. 1602

7.3.56.1

Test purpose p. 1602

7.3.56.2

Test applicability p. 1602

7.3.56.3

Minimum conformance requirements p. 1602

7.3.56.4

Test description p. 1602

7.3.56.4.1	Initial conditions p. 1603
7.3.56.4.2	Test procedure p. 1604
7.3.56.4.3	Message contents p. 1604

7.3.56.5

Test requirement p. 1606

7.3.57

E-UTRAN TDD Radio Link Monitoring Test for In-Sync for CE UE in CEModeA p. 1606

7.3.57.1

Test purpose p. 1606

7.3.57.2

Test applicability p. 1607

7.3.57.3

Minimum conformance requirements p. 1607

7.3.57.4

Test description p. 1607

7.3.57.4.1	Initial conditions p. 1608
7.3.57.4.2	Test procedure p. 1608
7.3.57.4.3	Message contents p. 1609

7.3.57.5

Test requirement p. 1610

7.3.58

E- UTRAN TDD Radio Link Monitoring Test for Out-of-sync in DRX for CE UE in CEModeA p. 1611

7.3.58.1

Test purpose p. 1611

7.3.58.2

Test applicability p. 1611

7.3.58.3

Minimum conformance requirements p. 1611

7.3.58.4

Test description p. 1612

7.3.58.4.1	Initial conditions p. 1613
7.3.58.4.2	Test procedure p. 1614
7.3.58.4.3	Message contents p. 1614

7.3.58.5

Test requirement p. 1616

7.3.59

E- UTRAN TDD Radio Link Monitoring Test for In-sync in DRX for CE UE in CEModeA p. 1617

7.3.59.1

Test purpose p. 1617

7.3.59.2

Test applicability p. 1617

7.3.59.3

Minimum conformance requirements p. 1618

7.3.59.4

Test description p. 1619

7.3.59.4.1	Initial conditions p. 1619
7.3.59.4.2	Test procedure p. 1620
7.3.59.4.3	Message contents p. 1621

7.3.59.5

Test requirement p. 1623

7.3.60

HD-FDD Radio Link Monitoring Test for Out-of-sync in DRX for UE category NB1 In-band mode in normal coverage p. 1624

7.3.60.1

Test purpose p. 1624

7.3.60.2

Test applicability p. 1624

7.3.60.3

Minimum conformance requirements p. 1624

7.3.60.4

Test description p. 1625

7.3.60.4.1	Initial conditions p. 1626
7.3.60.4.2	Test procedure p. 1627
7.3.60.4.3	Message contents p. 1628

7.3.60.5

Test requirement p. 1629

7.3.61

HD-FDD Radio Link Monitoring Test for Out-of-sync in DRX for UE category NB1 In-band mode in enhanced coverage p. 1630

7.3.61.1

Test purpose p. 1630

7.3.61.2

Test applicability p. 1630

7.3.61.3

Minimum conformance requirements p. 1630

7.3.61.4

Test description p. 1631

7.3.61.4.1	Initial conditions p. 1632
7.3.61.4.2	Test procedure p. 1633
7.3.61.4.3	Message contents p. 1634

7.3.61.5

Test requirement p. 1635

7.3.62

HD-FDD Radio Link Monitoring Test for In-sync with DRX for Category NB1 In-Band mode in Enhanced Coverage p. 1637

7.3.62.1

Test purpose p. 1637

7.3.62.2

Test applicability p. 1637

7.3.62.3

Minimum conformance requirements p. 1637

7.3.62.4

Test description p. 1638

7.3.62.4.1	Initial conditions p. 1638
7.3.62.4.2	Test procedure p. 1639
7.3.62.4.3	Message contents p. 1640

7.3.62.5

Test requirement p. 1640

7.3.63

HD-FDD Radio Link Monitoring Test for In-sync with DRX for Category NB1 In-Band mode in Normal Coverage p. 1642

7.3.63.1

Test purpose p. 1642

7.3.63.2

Test applicability p. 1642

7.3.63.3

Minimum conformance requirements p. 1642

7.3.63.4

Test description p. 1643

7.3.63.4.1	Initial conditions p. 1643
7.3.63.4.2	Test procedure p. 1644
7.3.63.4.3	Message contents p. 1645

7.3.63.5

Test requirement p. 1645

7.3.64

HD-FDD Radio Link Monitoring Test for In-sync without DRX for UE Category NB1 In-Band mode in Normal Coverage p. 1647

7.3.64.1

Test Purpose p. 1647

7.3.64.2

Test Applicability p. 1647

7.3.64.3

Minimum Conformance Requirements p. 1647

7.3.64.4

Test description p. 1647

7.3.64.4.1	Initial conditions p. 1648
7.3.64.4.2	Test procedure p. 1649
7.3.64.4.3	Message contents p. 1650

7.3.64.5

Test requirement p. 1650

7.3.65

HD-FDD Radio Link Monitoring Test for In-sync without DRX for UE Category NB1 In-Band mode in Enhanced Coverage p. 1651

7.3.65.1

Test Purpose p. 1651

7.3.65.2

Test Applicability p. 1651

7.3.65.3

Minimum Conformance Requirements p. 1652

7.3.65.4

Test description p. 1652

7.3.65.4.1	Initial conditions p. 1653
7.3.65.4.2	Test procedure p. 1654
7.3.65.4.3	Message contents p. 1654

7.3.65.5

Test requirement p. 1655

7.3.66

HD-FDD Radio Link Monitoring Test for Out-of-sync without DRX for UE Category NB1 Standalone mode in Normal Coverage p. 1656

7.3.66.1

Test purpose p. 1656

7.3.66.2

Test applicability p. 1656

7.3.66.3

Minimum conformance requirements p. 1657

7.3.66.4

Test description p. 1657

7.3.66.4.1	Initial conditions p. 1658
7.3.66.4.2	Test procedure p. 1659
7.3.66.4.3	Message contents p. 1659

7.3.66.5

Test requirement p. 1660

7.3.67

HD-FDD Radio Link Monitoring Test for Out-of-sync without DRX for UE Category NB1 guard band mode in Enhanced Coverage p. 1660

7.3.67.1

Test purpose p. 1660

7.3.67.2

Test applicability p. 1661

7.3.67.3

Minimum conformance requirements p. 1661

7.3.67.4

Test description p. 1661

7.3.67.4.1	Initial conditions p. 1661
7.3.67.4.2	Test procedure p. 1662
7.3.67.4.3	Message contents p. 1663

7.3.67.5

Test requirement p. 1664

7.3.68

- p. 1665

7.3.69

E-UTRAN HD-FDD Early Out-of-sync reporting Test for CE UE in CEMode A p. 1665

7.3.69.1

Test purpose p. 1665

7.3.69.2

Test applicability p. 1665

7.3.69.3

Minimum conformance requirements p. 1666

7.3.69.4

Test description p. 1667

7.3.69.4.1	Initial conditions p. 1667
7.3.69.4.2	Test procedure p. 1668
7.3.69.4.3	Message contents p. 1668

7.3.69.5

Test requirement p. 1670

7.3.70_87

Void p. …

7.3.88

TDD Radio Link Monitoring Test for Out-of-sync in DRX for UE category NB1 In-band mode in normal coverage p. 1671

7.3.88.1

Test purpose p. 1671

7.3.88.2

Test applicability p. 1671

7.3.88.3

Minimum conformance requirements p. 1671

7.3.88.4

Test description p. 1671

7.3.88.4.1	Initial conditions p. 1671
7.3.88.4.2	Test procedure p. 1672
7.3.88.4.3	Message contents p. 1672

7.3.88.5

Test requirement p. 1672

7.3.89

TDD Radio Link Monitoring Test for Out-of-sync in DRX for UE category NB1 In-band mode in enhanced coverage p. 1674

7.3.89.1

Test purpose p. 1674

7.3.89.2

Test applicability p. 1674

7.3.89.3

Minimum conformance requirements p. 1674

7.3.89.4

Test description p. 1674

7.3.89.4.1	Initial conditions p. 1674
7.3.89.4.2	Test procedure p. 1675
7.3.89.4.3	Message contents p. 1675

7.3.89.5

Test requirement p. 1675

7.3.90

TDD Radio Link Monitoring Test for In-sync with DRX for UE Category NB1 In-Band mode in Normal Coverage p. 1677

7.3.90.1

Test purpose p. 1677

7.3.90.2

Test applicability p. 1677

7.3.90.3

Minimum conformance requirements p. 1677

7.3.90.4

Test description p. 1677

7.3.90.4.1	Initial conditions p. 1677
7.3.90.4.2	Test procedure p. 1678
7.3.90.4.3	Message contents p. 1678

7.3.90.5

Test requirement p. 1679

7.3.91

TDD Radio Link Monitoring Test for In-sync with DRX for UE Category NB1 In-Band mode in Enhanced Coverage p. 1680

7.3.91.1

Test purpose p. 1680

7.3.91.2

Test applicability p. 1681

7.3.91.3

Minimum conformance requirements p. 1681

7.3.91.4

Test description p. 1681

7.3.91.4.1	Initial conditions p. 1681
7.3.91.4.2	Test procedure p. 1682
7.3.91.4.3	Message contents p. 1682

7.3.91.5

Test requirement p. 1682

7.3.92

TDD Radio Link Monitoring Test for In-sync without DRX for UE Category NB1 In-Band mode in Normal Coverage p. 1684

7.3.92.1

Test purpose p. 1684

7.3.92.2

Test applicability p. 1684

7.3.92.3

Minimum conformance requirements p. 1684

7.3.92.4

Test description p. 1684

7.3.92.4.1	Initial conditions p. 1684
7.3.92.4.2	Test procedure p. 1685
7.3.92.4.3	Message contents p. 1685

7.3.92.5

Test requirement p. 1686

7.3.93

TDD Radio Link Monitoring Test for In-sync without DRX for UE Category NB1 In-Band mode in Enhanced Coverage p. 1687

7.3.93.1

Test purpose p. 1687

7.3.93.2

Test applicability p. 1687

7.3.93.3

Minimum conformance requirements p. 1687

7.3.93.4

Test description p. 1688

7.3.93.4.1	Initial conditions p. 1688
7.3.93.4.2	Test procedure p. 1689
7.3.93.4.3	Message contents p. 1689

7.3.93.5

Test requirement p. 1689

7.3.94

TDD Radio Link Monitoring Test for Out-of-sync without DRX for UE Category NB1 Standalone mode in Normal Coverage p. 1690

7.3.94.1

Test purpose p. 1690

7.3.94.2

Test applicability p. 1690

7.3.94.3

Minimum conformance requirements p. 1690

7.3.94.4

Test description p. 1691

7.3.94.4.1	Initial conditions p. 1691
7.3.94.4.2	Test procedure p. 1691
7.3.94.4.3	Message contents p. 1691

7.3.94.5

Test requirement p. 1692

7.3.95

TDD Radio Link Monitoring Test for Out-of-sync without DRX for UE Category NB1 guard band mode in Enhanced Coverage p. 1692

7.3.95.1

Test purpose p. 1692

7.3.95.2

Test applicability p. 1692

7.3.95.3

Minimum conformance requirements p. 1693

7.3.95.4

Test description p. 1693

7.3.95.4.1	Initial conditions p. 1693
7.3.95.4.2	Test procedure p. 1693
7.3.95.4.3	Message contents p. 1694

7.3.95.5

Test requirement p. 1694

7.4

Interruption for Dual Connectivity p. 1696

7.4.1

E-UTRAN FDD-FDD DC interruption at transitions between active and non-active during DRX in synchronous DC p. 1696

7.4.1.1

Test purpose p. 1696

7.4.1.2

Test applicability p. 1696

7.4.1.3

Minimum conformance requirements p. 1696

7.4.1.4

Test description p. 1696

7.4.1.4.1	Initial conditions p. 1696
7.4.1.4.2	Test procedure p. 1697
7.4.1.4.3	Message contents p. 1698

7.4.1.5

Test requirement p. 1698

7.4.2

E-UTRAN TDD-TDD DC interruption at transitions between active and non-active during DRX in synchronous DC p. 1700

7.4.2.1

Test purpose p. 1700

7.4.2.2

Test applicability p. 1700

7.4.2.3

Minimum conformance requirements p. 1700

7.4.2.4

Test description p. 1700

7.4.2.4.1	Initial conditions p. 1700
7.4.2.4.2	Test procedure p. 1701
7.4.2.4.3	Message contents p. 1702

7.4.2.5

Test requirement p. 1703

7.4.3

E-UTRAN FDD-FDD Interruption at transitions between active and non-active during DRX in asynchronous dual connectivity p. 1704

7.4.3.1

Test Purpose p. 1704

7.4.3.2

Test Applicability p. 1704

7.4.3.3

Minimum Conformance Requirement p. 1704

7.4.3.4

Test Description p. 1704

7.4.3.4.1	Initial conditions p. 1704
7.4.3.4.2	Test procedure p. 1705
7.4.3.4.3	Message contents p. 1706

7.4.3.5

Test Requirement p. 1706

7.5

Proximity-based Services p. 1708

7.5.1

E-UTRAN FDD - UE ProSe Direct Discovery Transmission Timing Accuracy Test p. 1708

7.5.1.1

Test purpose p. 1708

7.5.1.2

Test applicability p. 1708

7.5.1.3

Minimum conformance requirements p. 1708

7.5.1.4

Test description p. 1708

7.5.1.4.1	Initial conditions p. 1708
7.5.1.4.2	Test procedure p. 1709
7.5.1.4.3	Message contents p. 1709

7.5.1.5

Test requirement p. 1709

7.5.2

FFS p. 1710

7.5.3

E-UTRAN FDD - Interruptions due to ProSe Direct Discovery p. 1710

7.5.3.1

Test purpose p. 1710

7.5.3.2

Test applicability p. 1710

7.5.3.3

Minimum conformance requirements p. 1710

7.5.3.4

Test description p. 1712

7.5.3.4.1	Initial conditions p. 1712
7.5.3.4.2	Test procedure p. 1713
7.5.3.4.3	Message contents p. 1713

7.5.3.5

Test requirement p. 1713

7.5.4

E-UTRAN FDD - UE ProSe Direct Communication Transmission Timing Accuracy Test p. 1714

7.5.4.1

Test purpose p. 1714

7.5.4.2

Test applicability p. 1714

7.5.4.3

Minimum conformance requirements p. 1715

7.5.4.4

Test description p. 1715

7.5.4.4.1	Initial conditions p. 1715
7.5.4.4.2	Test procedure p. 1715
7.5.4.4.3	Message contents p. 1715

7.5.4.5

Test requirement p. 1716

7.6

Interruption for carrier aggregation p. 1717

7.6.1

E-UTRAN FDD-TDD CA interruption at SRS carrier based switching p. 1717

7.6.1.1

Test purpose p. 1717

7.6.1.2

Test applicability p. 1717

7.6.1.3

Minimum conformance requirements p. 1717

7.6.1.4

Test description p. 1717

7.6.1.4.1	Initial conditions p. 1717
7.6.1.4.2	Test procedure p. 1718
7.6.1.4.3	Message contents p. 1718

7.6.1.5

Test requirement p. 1720

7.6.2

E-UTRAN TDD-TDD CA interruption at SRS carrier based switching p. 1722

7.6.2.1

Test purpose p. 1722

7.6.2.2

Test applicability p. 1722

7.6.2.3

Minimum conformance requirements p. 1722

7.6.2.4

Test description p. 1722

7.6.2.4.1	Initial conditions p. 1722
7.6.2.4.2	Test procedure p. 1723
7.6.2.4.3	Message contents p. 1724

7.6.2.5

Test requirement p. 1725

UE Measurements Procedures p. 1728

8.0

- p. 1728

8.1

E-UTRAN FDD intra frequency measurements p. 1728

8.1.1

E-UTRAN FDD-FDD intra frequency event triggered reporting under fading propagation conditions in asynchronous cells p. 1728

8.1.1.1

Test purpose p. 1728

8.1.1.2

Test applicability p. 1728

8.1.1.3

Minimum conformance requirements p. 1728

8.1.1.4

Test description p. 1729

8.1.1.4.1	Initial conditions p. 1729
8.1.1.4.2	Test procedure p. 1730
8.1.1.4.3	Message contents p. 1731

8.1.1.5

Test requirement p. 1732

8.1.2

E-UTRAN FDD-FDD intra frequency event triggered reporting under fading propagation conditions in synchronous cells p. 1734

8.1.2.1

Test purpose p. 1734

8.1.2.2

Test applicability p. 1734

8.1.2.3

Minimum conformance requirements p. 1734

8.1.2.4

Test description p. 1735

8.1.2.4.1	Initial conditions p. 1735
8.1.2.4.2	Test procedure p. 1736
8.1.2.4.3	Message contents p. 1736

8.1.2.5

Test requirement p. 1738

8.1.3

E-UTRAN FDD-FDD intra frequency event triggered reporting under fading propagation conditions in synchronous cells with DRX p. 1739

8.1.3.1

Test purpose p. 1739

8.1.3.2

Test applicability p. 1739

8.1.3.3

Minimum conformance requirements p. 1739

8.1.3.4

Test description p. 1740

8.1.3.4.1	Initial conditions p. 1740
8.1.3.4.2	Test procedure p. 1741
8.1.3.4.3	Message contents p. 1741

8.1.3.5

Test requirement p. 1744

8.1.4

Void p. …

8.1.5

E-UTRAN FDD - FDD Intra-frequency identification of a new CGI of E-UTRA cell using autonomous gaps p. 1746

8.1.5.1

Test purpose p. 1746

8.1.5.2

Test applicability p. 1746

8.1.5.3

Minimum conformance requirements p. 1746

8.1.5.4

Test description p. 1747

8.1.5.4.1	Initial conditions p. 1747
8.1.5.4.2	Test procedure p. 1748
8.1.5.4.3	Message contents p. 1748

8.1.5.5

Test requirement p. 1752

8.1.6

E-UTRAN FDD - FDD Intra-frequency identification of a new CGI of E-UTRA cell using autonomous gaps with DRX p. 1754

8.1.6.1

Test purpose p. 1754

8.1.6.2

Test applicability p. 1754

8.1.6.3

Minimum conformance requirements p. 1754

8.1.6.4

Test description p. 1754

8.1.6.4.1	Initial conditions p. 1754
8.1.6.4.2	Test procedure p. 1755
8.1.6.4.3	Message contents p. 1756

8.1.6.5

Test requirement p. 1760

8.1.7

E-UTRAN FDD-FDD Intra-Frequency Event-Triggered Reporting under Time Domain Measurement Resource Restriction with Non-MBSFN ABS (eICIC) p. 1762

8.1.7.1

Test purpose p. 1762

8.1.7.2

Test applicability p. 1762

8.1.7.3

Minimum conformance requirements p. 1762

8.1.7.4

Test description p. 1763

8.1.7.4.1	Initial conditions p. 1763
8.1.7.4.2	Test procedure p. 1764
8.1.7.4.3	Message contents p. 1765

8.1.7.5

Test requirements p. 1768

8.1.8

E-UTRAN FDD-FDD Intra-Frequency Event-Triggered Reporting under Time Domain Measurement Resource Restriction with CRS Assistance Information and Non-MBSFN ABS (feICIC) p. 1769

8.1.8.1

Test purpose p. 1769

8.1.8.2

Test applicability p. 1769

8.1.8.3

Minimum conformance requirements p. 1769

8.1.8.4

Test description p. 1770

8.1.8.4.1	Initial conditions p. 1770
8.1.8.4.2	Test procedure p. 1772
8.1.8.4.3	Message contents p. 1772

8.1.8.5

Test requirements p. 1775

8.1.9

E-UTRAN FDD-FDD intra frequency event triggered reporting under fading propagation conditions in asynchronous cells for 5MHz Bandwidth p. 1776

8.1.9.1

Test purpose p. 1776

8.1.9.2

Test applicability p. 1777

8.1.9.3

Minimum conformance requirements p. 1777

8.1.9.4

Test description p. 1777

8.1.9.4.1	Initial conditions p. 1777
8.1.9.4.2	Test procedure p. 1777
8.1.9.4.3	Message contents p. 1777

8.1.9.5

Test requirement p. 1777

8.1.10

E-UTRAN FDD-FDD intra frequency event triggered reporting under fading propagation conditions in synchronous cells with DRX for 5MHz Bandwidth p. 1778

8.1.10.1

Test purpose p. 1778

8.1.10.2

Test applicability p. 1778

8.1.10.3

Minimum conformance requirements p. 1778

8.1.10.4

Test description p. 1778

8.1.10.4.1	Initial conditions p. 1778
8.1.10.4.2	Test procedure p. 1779
8.1.10.4.3	Message contents p. 1779

8.1.10.5

Test requirement p. 1779

8.1.11

E-UTRAN FDD-FDD intra-frequency event triggered reporting under fading propagation conditions in asynchronous cells for UE category 0 p. 1779

8.1.11.1

Test purpose p. 1779

8.1.11.2

Test applicability p. 1779

8.1.11.3

Minimum conformance requirements p. 1780

8.1.11.4

Test description p. 1781

8.1.11.4.1	Initial conditions p. 1781
8.1.11.4.2	Test procedure p. 1782
8.1.11.4.3	Message contents p. 1782

8.1.11.5

Test requirement p. 1784

8.1.11_2

E-UTRAN FDD-FDD intra-frequency event triggered reporting under fading propagation conditions in asynchronous cells for UE category 1bis p. 1785

8.1.11_2.1

Test purpose p. 1785

8.1.11_2.2

Test applicability p. 1785

8.1.11_2.3

Minimum conformance requirements p. 1785

8.1.11_2.4

Test description p. 1786

8.1.11_2.4.1	Initial conditions p. 1786
8.1.11_2.4.2	Test procedure p. 1787
8.1.11_2.4.3	Message contents p. 1788

8.1.11_2.5

Test requirement p. 1789

8.1.12

E-UTRAN FDD-FDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells for UE category 0 p. 1790

8.1.12.1

Test purpose p. 1790

8.1.12.2

Test applicability p. 1790

8.1.12.3

Minimum conformance requirements p. 1790

8.1.12.4

Test description p. 1792

8.1.12.4.1	Initial conditions p. 1792
8.1.12.4.2	Test procedure p. 1792
8.1.12.4.3	Message contents p. 1793

8.1.12.5

Test requirement p. 1795

8.1.12_2

E-UTRAN FDD-FDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells for UE category 1bis p. 1796

8.1.12_2.1

Test purpose p. 1796

8.1.12_2.2

Test applicability p. 1796

8.1.12_2.3

Minimum conformance requirements p. 1796

8.1.12_2.4

Test description p. 1798

8.1.12_2.4.1	Initial conditions p. 1798
8.1.12_2.4.2	Test procedure p. 1798
8.1.12_2.4.3	Message contents p. 1799

8.1.12_2.5

Test requirement p. 1800

8.1.13

E-UTRAN FDD-FDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells with DRX for UE category 0 p. 1802

8.1.13.1

Test purpose p. 1802

8.1.13.2

Test applicability p. 1802

8.1.13.3

Minimum conformance requirements p. 1802

8.1.13.4

Test description p. 1803

8.1.13.4.1	Initial conditions p. 1803
8.1.13.4.2	Test procedure p. 1804
8.1.13.4.3	Message contents p. 1804

8.1.13.5

Test requirement p. 1806

8.1.13_2

E-UTRAN FDD-FDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells with DRX for UE category 1bis p. 1809

8.1.13_2.1

Test purpose p. 1809

8.1.13_2.2

Test applicability p. 1809

8.1.13_2.3

Minimum conformance requirements p. 1809

8.1.13_2.4

Test description p. 1810

8.1.13_2.4.1	Initial conditions p. 1810
8.1.13_2.4.2	Test procedure p. 1811
8.1.13_2.4.3	Message contents p. 1811

8.1.13_2.5

Test requirement p. 1813

8.1.14

E-UTRAN HD-FDD intra-frequency event triggered reporting under fading propagation conditions in asynchronous cells for UE category 0 p. 1816

8.1.14.1

Test purpose p. 1816

8.1.14.2

Test applicability p. 1816

8.1.14.3

Minimum conformance requirements p. 1816

8.1.14.4

Test description p. 1817

8.1.14.4.1	Initial conditions p. 1817
8.1.14.4.2	Test procedure p. 1818
8.1.14.4.3	Message contents p. 1819

8.1.14.5

Test requirement p. 1820

8.1.15

E-UTRAN HD-FDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells for UE category 0 p. 1821

8.1.15.1

Test purpose p. 1822

8.1.15.2

Test applicability p. 1822

8.1.15.3

Minimum conformance requirements p. 1822

8.1.15.4

Test description p. 1823

8.1.15.4.1	Initial conditions p. 1823
8.1.15.4.2	Test procedure p. 1824
8.1.15.4.3	Message contents p. 1824

8.1.15.5

Test requirement p. 1826

8.1.16

E-UTRAN HD-FDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells with DRX for UE category 0 p. 1827

8.1.16.1

Test purpose p. 1827

8.1.16.2

Test applicability p. 1827

8.1.16.3

Minimum conformance requirements p. 1827

8.1.16.4

Test description p. 1828

8.1.16.4.1	Initial conditions p. 1828
8.1.16.4.2	Test procedure p. 1829
8.1.16.4.3	Message contents p. 1830

8.1.16.5

Test requirement p. 1832

8.1.17

E-UTRAN TDD-TDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells for UE category 0 p. 1834

8.1.17.1

Test purpose p. 1834

8.1.17.2

Test applicability p. 1834

8.1.17.3

Minimum conformance requirements p. 1834

8.1.17.4

Test description p. 1835

8.1.17.4.1	Initial conditions p. 1835
8.1.17.4.2	Test procedure p. 1836
8.1.17.4.3	Message contents p. 1836

8.1.17.5

Test requirement p. 1838

8.1.17_2

E-UTRAN TDD-TDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells for UE category 1bis p. 1840

8.1.17_2.1

Test purpose p. 1840

8.1.17_2.2

Test applicability p. 1840

8.1.17_2.3

Minimum conformance requirements p. 1840

8.1.17_2.4

Test description p. 1841

8.1.17_2.4.1	Initial conditions p. 1841
8.1.17_2.4.2	Test procedure p. 1842
8.1.17_2.4.3	Message contents p. 1842

8.1.17_2.5

Test requirement p. 1844

8.1.18

E-UTRAN TDD-TDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells with DRX for UE category 0 p. 1845

8.1.18.1

Test purpose p. 1845

8.1.18.2

Test applicability p. 1846

8.1.18.3

Minimum conformance requirements p. 1846

8.1.18.4

Test description p. 1847

8.1.18.4.1	Initial conditions p. 1847
8.1.18.4.2	Test procedure p. 1848
8.1.18.4.3	Message contents p. 1848

8.1.18.5

Test requirement p. 1851

8.1.18_2

E-UTRAN TDD-TDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells with DRX for UE category 1bis p. 1853

8.1.18_2.1

Test purpose p. 1853

8.1.18_2.2

Test applicability p. 1853

8.1.18_2.3

Minimum conformance requirements p. 1853

8.1.18_2.4

Test description p. 1854

8.1.18_2.4.1	Initial conditions p. 1854
8.1.18_2.4.2	Test procedure p. 1855
8.1.18_2.4.3	Message contents p. 1856

8.1.18_2.5

Test requirement p. 1858

8.1.19

E-UTRAN FD - FDD Intra-frequency identification of a new CGI of E-UTRA cell using autonomous gaps for UE category 0 p. 1860

8.1.19.1

Test purpose p. 1860

8.1.19.2

Test applicability p. 1860

8.1.19.3

Minimum conformance requirements p. 1860

8.1.19.4

Test description p. 1861

8.1.19.4.1	Initial conditions p. 1861
8.1.19.4.2	Test procedure p. 1862
8.1.19.4.3	Message contents p. 1863

8.1.19.5

Test requirement p. 1866

8.1.19_2

E-UTRAN FDD - FDD Intra-frequency identification of a new CGI of E-UTRA cell using autonomous gaps for UE category 1bis p. 1868

8.1.19_2.1

Test purpose p. 1868

8.1.19_2.2

Test applicability p. 1868

8.1.19_2.3

Minimum conformance requirements p. 1868

8.1.19_2.4

Test description p. 1869

8.1.19_2.4.1

Initial conditions p. 1869

8.1.19_2.5

Test requirement p. 1869

8.1.20

E-UTRAN FDD - FDD Intra-frequency identification of a new CGI of E-UTRA cell using autonomous gaps with DRX for UE category 0 p. 1871

8.1.20.1

Test purpose p. 1871

8.1.20.2

Test applicability p. 1871

8.1.20.3

Minimum conformance requirements p. 1871

8.1.20.4

Test description p. 1872

8.1.20.4.1	Initial conditions p. 1872
8.1.20.4.2	Test procedure p. 1872
8.1.20.4.3	Message contents p. 1873

8.1.20.5

Test requirement p. 1877

8.1.20_2

E-UTRAN FDD - FDD Intra-frequency identification of a new CGI of E-UTRA cell using autonomous gaps with DRX for UE category 1bis p. 1879

8.1.20_2.1

Test purpose p. 1879

8.1.20_2.2

Test applicability p. 1879

8.1.20_2.3

Minimum conformance requirements p. 1879

8.1.20_2.4

Test description p. 1880

8.1.20_2.4.1

Initial conditions p. 1880

8.1.20_2.5

Test requirement p. 1880

8.1.21

E-UTRAN HD - FDD Intra-frequency identification of a new CGI of E-UTRA cell using autonomous gaps for UE category 0 p. 1882

8.1.21.1

Test purpose p. 1882

8.1.21.2

Test applicability p. 1882

8.1.21.3

Minimum conformance requirements p. 1882

8.1.21.4

Test description p. 1883

8.1.21.4.1	Initial conditions p. 1883
8.1.21.4.2	Test procedure p. 1884
8.1.21.4.3	Message contents p. 1884

8.1.21.5

Test requirement p. 1888

8.1.22

E-UTRAN HD- FDD Intra-frequency identification of a new CGI of E-UTRA cell using autonomous gaps with DRX for UE category 0 p. 1889

8.1.22.1

Test purpose p. 1889

8.1.22.2

Test applicability p. 1889

8.1.22.3

Minimum conformance requirements p. 1890

8.1.22.4

Test description p. 1890

8.1.22.4.1	Initial conditions p. 1890
8.1.22.4.2	Test procedure p. 1891
8.1.22.4.3	Message contents p. 1892

8.1.22.5

Test requirement p. 1896

8.1.23

E-UTRAN FDD-FDD intra-frequency event triggered reporting under fading propagation conditions in asynchronous cells for CE UEin CEModeA p. 1898

8.1.23.1

Test purpose p. 1898

8.1.23.2

Test applicability p. 1898

8.1.23.3

Minimum conformance requirements p. 1898

8.1.23.4

Test description p. 1899

8.1.23.4.1	Initial conditions p. 1899
8.1.23.4.2	Test procedure p. 1900
8.1.23.4.3	Message contents p. 1900

8.1.23.5

Test requirement p. 1902

8.1.24

E-UTRAN FDD-FDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells for CE UE in CEModeA p. 1903

8.1.24.1

Test purpose p. 1903

8.1.24.2

Test applicability p. 1903

8.1.24.3

Minimum conformance requirements p. 1903

8.1.24.4

Test description p. 1903

8.1.24.4.1	Initial conditions p. 1903
8.1.24.4.2	Test procedure p. 1904
8.1.24.4.3	Message contents p. 1904

8.1.24.5

Test requirement p. 1904

8.1.25

E-UTRAN FDD-FDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells for CE UEin CEModeA in DRX p. 1905

8.1.25.1

Test purpose p. 1905

8.1.25.2

Test applicability p. 1905

8.1.25.3

Minimum conformance requirements p. 1905

8.1.25.4

Test description p. 1907

8.1.25.4.1	Initial conditions p. 1907
8.1.25.4.2	Test procedure p. 1907
8.1.25.4.3	Message contents p. 1908

8.1.25.5

Test requirement p. 1910

8.1.26

E-UTRAN HD-FDD intra-frequency event triggered reporting under fading propagation conditions in asynchronous cells for CE UE in CEModeA p. 1912

8.1.26.1

Test purpose p. 1912

8.1.26.2

Test applicability p. 1912

8.1.26.3

Minimum conformance requirements p. 1913

8.1.26.4

Test description p. 1913

8.1.26.4.1	Initial conditions p. 1913
8.1.26.4.2	Test procedure p. 1914
8.1.26.4.3	Message contents p. 1915

8.1.26.5

Test requirement p. 1916

8.1.27

E-UTRAN HD-FDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells for CE UE in CEModeA p. 1918

8.1.27.1

Test purpose p. 1918

8.1.27.2

Test applicability p. 1918

8.1.27.3

Minimum conformance requirements p. 1918

8.1.27.4

Test description p. 1919

8.1.27.4.1	Initial conditions p. 1919
8.1.27.4.2	Test procedure p. 1919
8.1.27.4.3	Message contents p. 1920

8.1.27.5

Test requirement p. 1922

8.1.28

E-UTRAN HD-FDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells for CE UE in CEModeA in DRX p. 1924

8.1.28.1

Test purpose p. 1924

8.1.28.2

Test applicability p. 1924

8.1.28.3

Minimum conformance requirements p. 1924

8.1.28.4

Test description p. 1925

8.1.28.4.1	Initial conditions p. 1925
8.1.28.4.2	Test procedure p. 1926
8.1.28.4.3	Message contents p. 1927

8.1.28.5

Test requirement p. 1928

8.1.29

E-UTRAN TDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells for CE UE in CEModeA p. 1931

8.1.29.1

Test purpose p. 1931

8.1.29.2

Test applicability p. 1931

8.1.29.3

Minimum conformance requirements p. 1931

8.1.29.4

Test description p. 1932

8.1.29.4.1	Initial conditions p. 1932
8.1.29.4.2	Test procedure p. 1933
8.1.29.4.3	Message contents p. 1933

8.1.29.5

Test requirement p. 1934

8.1.30

E-UTRAN TDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells for CE UE in CEModeA in DRX p. 1936

8.1.30.1

Test purpose p. 1936

8.1.30.2

Test applicability p. 1936

8.1.30.3

Minimum conformance requirements p. 1936

8.1.30.4

Test description p. 1937

8.1.30.4.1	Initial conditions p. 1937
8.1.30.4.2	Test procedure p. 1938
8.1.30.4.3	Message contents p. 1939

8.1.30.5

Test requirement p. 1941

8.1.31

E-UTRAN FDD-FDD intra-frequency event triggered reporting under fading propagation conditions in asynchronous cells for CE UE in CEModeB p. 1943

8.1.31.1

Test purpose p. 1943

8.1.31.2

Test applicability p. 1943

8.1.31.3

Minimum conformance requirements p. 1944

8.1.31.4

Test description p. 1945

8.1.31.4.1	Initial conditions p. 1945
8.1.31.4.2	Test procedure p. 1945
8.1.31.4.3	Message contents p. 1946

8.1.31.5

Test requirement p. 1947

8.1.32

E-UTRAN FDD-FDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells for CE UE in CEModeB p. 1949

8.1.32.1

Test purpose p. 1949

8.1.32.2

Test applicability p. 1949

8.1.32.3

Minimum conformance requirements p. 1949

8.1.32.4

Test description p. 1949

8.1.32.4.1	Initial conditions p. 1949
8.1.32.4.2	Test procedure p. 1949
8.1.32.4.3	Message contents p. 1949

8.1.32.5

Test requirement p. 1949

8.1.33

E-UTRAN HD-FDD Intra-frequency event triggered reporting under fading propagation conditions in asynchronous cells for CE UE in CEModeB p. 1951

8.1.33.1

Test purpose p. 1951

8.1.33.2

Test applicability p. 1951

8.1.33.3

Minimum conformance requirements p. 1951

8.1.33.4

Test description p. 1952

8.1.33.4.1	Initial conditions p. 1952
8.1.33.4.2	Test procedure p. 1953
8.1.33.4.3	Message contents p. 1953

8.1.33.5

Test requirement p. 1955

8.1.34

E-UTRAN HD-FDD Intra-frequency event triggered reporting under fading propagation conditions in synchronous cells for CE UE in CEModeB p. 1956

8.1.34.1

Test purpose p. 1956

8.1.34.2

Test applicability p. 1956

8.1.34.3

Minimum conformance requirements p. 1956

8.1.34.4

Test description p. 1957

8.1.34.4.1	Initial conditions p. 1957
8.1.34.4.2	Test procedure p. 1958
8.1.34.4.3	Message contents p. 1959

8.1.34.5

Test requirement p. 1960

8.1.35

E-UTRAN TDD Intra-frequency event triggered reporting under fading propagation conditions in synchronous cells for CE UE in CEModeB p. 1962

8.1.35.1

Test purpose p. 1962

8.1.35.2

Test applicability p. 1962

8.1.35.3

Minimum conformance requirements p. 1962

8.1.35.4

Test description p. 1963

8.1.35.4.1	Initial conditions p. 1963
8.1.35.4.2	Test procedure p. 1964
8.1.35.4.3	Message contents p. 1964

8.1.35.5

Test requirement p. 1966

8.1.36

E-UTRAN FDD Intra-frequency identification of a new CGI of E-UTRA cell using autonomous gaps for CE UE in CEModeB p. 1967

8.1.36.1

Test purpose p. 1967

8.1.36.2

Test applicability p. 1967

8.1.36.3

Minimum conformance requirements p. 1967

8.1.36.4

Test description p. 1968

8.1.36.4.1	Initial conditions p. 1968
8.1.36.4.2	Test procedure p. 1969
8.1.36.4.3	Message contents p. 1970

8.1.36.5

Test requirement p. 1973

8.1.37

E-UTRAN FDD Intra-frequency identification of a new CGI of E-UTRA cell using autonomous gaps with DRX for CE UE in CEModeB p. 1974

8.1.37.1

Test purpose p. 1974

8.1.37.2

Test applicability p. 1974

8.1.37.3

Minimum conformance requirements p. 1974

8.1.37.4

Test description p. 1975

8.1.37.4.1	Initial conditions p. 1975
8.1.37.4.2	Test procedure p. 1976
8.1.37.4.3	Message contents p. 1977

8.1.37.5

Test requirement p. 1981

8.1.38

E-UTRAN HD- FDD Intra-frequency identification of a new CGI of E-UTRA cell using autonomous gaps for CE UE in CEModeB p. 1982

8.1.38.1

Test purpose p. 1983

8.1.38.2

Test applicability p. 1983

8.1.38.3

Minimum conformance requirements p. 1983

8.1.38.4

Test description p. 1984

8.1.38.4.1	Initial conditions p. 1984
8.1.38.4.2	Test procedure p. 1984
8.1.38.4.3	Message contents p. 1985

8.1.38.5

Test requirement p. 1988

8.1.39

E-UTRAN HD-FDD Intra-frequency identification of a new CGI of E-UTRA cell using autonomous gaps with DRX for CE UE in CEModeB p. 1990

8.1.39.1

Test purpose p. 1990

8.1.39.2

Test applicability p. 1990

8.1.39.3

Minimum conformance requirements p. 1990

8.1.39.4

Test description p. 1991

8.1.39.4.1	Initial conditions p. 1991
8.1.39.4.2	Test procedure p. 1991
8.1.39.4.3	Message contents p. 1992

8.1.39.5

Test requirement p. 1997

8.1.40

E-UTRAN FDD-FDD intra-frequency event triggered reporting for UE configured with highSpeedEnhancedMeasFlag in synchronous cells p. 1998

8.1.40.1

Test purpose p. 1998

8.1.40.2

Test applicability p. 1998

8.1.40.3

Minimum conformance requirements p. 1998

8.1.40.4

Test description p. 1999

8.1.40.4.1	Initial conditions p. 1999
8.1.40.4.2	Test procedure p. 2000
8.1.40.4.3	Message contents p. 2001

8.1.40.5

Test requirement p. 2002

8.1.41

E-UTRAN FDD intra-frequency event triggered reporting for serving cell under fading propagation conditions for CE UE in CEModeA without gap p. 2004

8.1.41.1

Test purpose p. 2004

8.1.41.2

Test applicability p. 2004

8.1.41.3

Minimum conformance requirements p. 2004

8.1.41.4

Test description p. 2005

8.1.41.4.1	Initial conditions p. 2005
8.1.41.4.2	Test procedure p. 2005
8.1.41.4.3	Message contents p. 2006

8.1.41.5

Test requirement p. 2008

8.1.42

E-UTRAN HD-FDD intra-frequency event triggered reporting for serving cell under fading propagation conditions for CE UE in CEModeA without gap p. 2009

8.1.42.1

Test purpose p. 2009

8.1.42.2

Test applicability p. 2009

8.1.42.3

Minimum conformance requirements p. 2009

8.1.42.4

Test description p. 2009

8.1.42.4.1	Initial conditions p. 2009
8.1.42.4.2	Test procedure p. 2010
8.1.42.4.3	Message contents p. 2010

8.1.42.5

Test requirement p. 2010

8.2

E-UTRAN TDD intra frequency measurements p. 2011

8.2.1

E-UTRAN TDD-TDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells p. 2011

8.2.1.1

Test purpose p. 2011

8.2.1.2

Test applicability p. 2011

8.2.1.3

Minimum conformance requirements p. 2011

8.2.1.4

Test description p. 2013

8.2.1.4.1	Initial conditions p. 2013
8.2.1.4.2	Test procedure p. 2013
8.2.1.4.3	Message contents p. 2014

8.2.1.5

Test requirement p. 2015

8.2.2

E-UTRAN TDD-TDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells with DRX p. 2017

8.2.2.1

Test purpose p. 2017

8.2.2.2

Test applicability p. 2017

8.2.2.3

Minimum conformance requirements p. 2017

8.2.2.4

Test description p. 2018

8.2.2.4.1	Initial conditions p. 2018
8.2.2.4.2	Test procedure p. 2019
8.2.2.4.3	Message contents p. 2020

8.2.2.5

Test requirement p. 2022

8.2.3

E-UTRAN TDD - TDD Intra-frequency identification of a new CGI of E-UTRA cell using autonomous gaps p. 2024

8.2.3.1

Test purpose p. 2024

8.2.3.2

Test applicability p. 2024

8.2.3.3

Minimum conformance requirements p. 2024

8.2.3.4

Test description p. 2025

8.2.3.4.1	Initial conditions p. 2025
8.2.3.4.2	Test procedure p. 2026
8.2.3.4.3	Message contents p. 2027

8.2.3.5

Test requirement p. 2030

8.2.4

E-UTRAN TDD - TDD Intra-frequency identification of a new CGI of E-UTRA cell using autonomous gaps with DRX p. 2031

8.2.4.1

Test purpose p. 2031

8.2.4.2

Test applicability p. 2031

8.2.4.3

Minimum conformance requirements p. 2031

8.2.4.4

Test description p. 2032

8.2.4.4.1	Initial conditions p. 2032
8.2.4.4.2	Test procedure p. 2033
8.2.4.4.3	Message contents p. 2034

8.2.4.5

Test requirement p. 2038

8.2.5

E-UTRAN TDD-TDD Intra-Frequency Event-Triggered Reporting under Time Domain Measurement Resource Restriction with Non-MBSFN ABS (eICIC) p. 2039

8.2.5.1

Test purpose p. 2039

8.2.5.2

Test applicability p. 2040

8.2.5.3

Minimum conformance requirements p. 2040

8.2.5.4

Test description p. 2041

8.2.5.4.1	Initial conditions p. 2041
8.2.5.4.2	Test procedure p. 2042
8.2.5.4.3	Message contents p. 2043

8.2.5.5

Test requirements p. 2045

8.2.6

E-UTRAN TDD-TDD Intra-Frequency Event-Triggered Reporting under Time Domain Measurement Resource Restriction with CRS Assistance Information and Non-MBSFN ABS (feICIC) p. 2046

8.2.6.1

Test purpose p. 2046

8.2.6.2

Test applicability p. 2046

8.2.6.3

Minimum conformance requirements p. 2046

8.2.6.4

Test description p. 2047

8.2.6.4.1	Initial conditions p. 2047
8.2.6.4.2	Test procedure p. 2049
8.2.6.4.3	Message contents p. 2049

8.2.6.5

Test requirements p. 2052

8.2.7

E-UTRAN TDD Intra-frequency identification of a new CGI of E-UTRA cell using autonomous gaps for UE category 0 p. 2053

8.2.7.1

Test purpose p. 2053

8.2.7.2

Test applicability p. 2053

8.2.7.3

Minimum conformance requirements p. 2054

8.2.7.4

Test description p. 2055

8.2.7.4.1	Initial conditions p. 2055
8.2.7.4.2	Test procedure p. 2055
8.2.7.4.3	Message contents p. 2056

8.2.7.5

Test requirement p. 2059

8.2.7_2

E-UTRAN TDD Intra-frequency identification of a new CGI of E UTRA cell using autonomous gaps for UE category 1bis p. 2061

8.2.7_2.1

Test purpose p. 2061

8.2.7_2.2

Test applicability p. 2061

8.2.7_2.3

Minimum conformance requirements p. 2061

8.2.7_2.4

Test description p. 2062

8.2.7_2.4.1	Initial conditions p. 2062
8.2.7_2.4.2	Test procedure p. 2063
8.2.7_2.4.3	Message contents p. 2064

8.2.7_2.5

Test requirement p. 2066

8.2.8

E-UTRAN TDD Intra-frequency identification of a new CGI of E-UTRA cell using autonomous gaps with DRX for UE category 0 p. 2067

8.2.8.1

Test purpose p. 2067

8.2.8.2

Test applicability p. 2067

8.2.8.3

Minimum conformance requirements p. 2068

8.2.8.4

Test description p. 2069

8.2.8.4.1	Initial conditions p. 2069
8.2.8.4.2	Test procedure p. 2069
8.2.8.4.3	Message contents p. 2070

8.2.8.5

Test requirement p. 2074

8.2.8_2

E-UTRAN TDD Intra-frequency identification of a new CGI of E-UTRA cell using autonomous gaps with DRX for UE category 1bis p. 2076

8.2.8_2.1

Test purpose p. 2076

8.2.8_2.2

Test applicability p. 2076

8.2.8_2.3

Minimum conformance requirements p. 2076

8.2.8_2.4

Test description p. 2077

8.2.8_2.4.1	Initial conditions p. 2077
8.2.8_2.4.2	Test procedure p. 2078
8.2.8_2.4.3	Message contents p. 2079

8.2.8_2.5

Test requirement p. 2083

8.2.9

E-UTRAN TDD Intra-frequency identification of a new CGI of E-UTRA cell using autonomous gaps for CE UE in CEModeB p. 2085

8.2.9.1

Test purpose p. 2085

8.2.9.2

Test applicability p. 2085

8.2.9.3

Minimum conformance requirements p. 2085

8.2.9.4

Test description p. 2086

8.2.9.4.1	Initial conditions p. 2086
8.2.9.4.2	Test procedure p. 2087
8.2.9.4.3	Message contents p. 2088

8.2.9.5

Test requirement p. 2091

8.2.10

E-UTRAN TDD Intra-frequency identification of a new CGI of E-UTRA cell using autonomous gaps with DRX for CE UE in CEModeB p. 2092

8.2.10.1

Test purpose p. 2092

8.2.10.2

Test applicability p. 2092

8.2.10.3

Minimum conformance requirements p. 2093

8.2.10.4

Test description p. 2093

8.2.10.4.1	Initial conditions p. 2093
8.2.10.4.2	Test procedure p. 2094
8.2.10.4.3	Message contents p. 2095

8.2.10.5

Test requirement p. 2099

8.2.11

E-UTRAN TDD-TDD intra-frequency event triggered reporting for UE configured with highSpeedEnhancedMeasFlag in synchronous cells p. 2101

8.2.11.1

Test purpose p. 2101

8.2.11.2

Test applicability p. 2101

8.2.11.3

Minimum conformance requirements p. 2101

8.2.11.4

Test description p. 2102

8.2.11.4.1	Initial conditions p. 2102
8.2.11.4.2	Test procedure p. 2103
8.2.11.4.3	Message contents p. 2104

8.2.11.5

Test requirement p. 2106

8.2.12

- p. 2108

8.2.13

- p. 2108

8.2.14

E-UTRAN TDD intra-frequency event triggered reporting for serving cell under fading propagation conditions for CE in CEModeA without gap p. 2108

8.2.14.1

Test purpose p. 2108

8.2.14.2

Test applicability p. 2108

8.2.14.3

Minimum conformance requirements p. 2108

8.2.14.4

Test description p. 2110

8.2.14.4.1	Initial conditions p. 2110
8.2.14.4.2	Test procedure p. 2111
8.2.14.4.3	Message contents p. 2112

8.2.14.5

Test requirement p. 2114

8.3

E-UTRAN FDD-FDD Inter-frequency Measurements p. 2116

8.3.1

E-UTRAN FDD-FDD Inter-frequency event triggered reporting under fading propagation conditions in asynchronous cells p. 2116

8.3.1.1

Test purpose p. 2116

8.3.1.2

Test applicability p. 2116

8.3.1.3

Minimum conformance requirements p. 2116

8.3.1.4

Test description p. 2117

8.3.1.4.1	Initial conditions p. 2117
8.3.1.4.2	Test procedure p. 2118
8.3.1.4.3	Message contents p. 2118

8.3.1.5

Test requirement p. 2119

8.3.1_2

E-UTRAN FDD-FDD Inter-frequency event triggered reporting under fading propagation conditions in asynchronous cells for UE category 1bis p. 2121

8.3.1_2.1

Test purpose p. 2121

8.3.1_2.2

Test applicability p. 2121

8.3.1_2.3

Minimum conformance requirements p. 2121

8.3.1_2.4

Test description p. 2122

8.3.1_2.4.1	Initial conditions p. 2122
8.3.1_2.4.2	Test procedure p. 2123
8.3.1_2.4.3	Message contents p. 2123

8.3.1_2.5

Test requirement p. 2124

8.3.2

E-UTRAN FDD-FDD Inter-frequency event triggered reporting when DRX is used under fading propagation conditions in asynchronous cells p. 2126

8.3.2.1

Test purpose p. 2126

8.3.2.2

Test applicability p. 2126

8.3.2.3

Minimum conformance requirements p. 2126

8.3.2.4

Test description p. 2127

8.3.2.4.1	Initial conditions p. 2127
8.3.2.4.2	Test procedure p. 2128
8.3.2.4.3	Message contents p. 2129

8.3.2.5

Test requirement p. 2131

8.3.2_2

E-UTRAN FDD-FDD Inter-frequency event triggered reporting when DRX is used under fading propagation conditions in asynchronous cells for UE category 1bis p. 2133

8.3.2_2.1

Test purpose p. 2133

8.3.2_2.2

Test applicability p. 2133

8.3.2_2.3

Minimum conformance requirements p. 2133

8.3.2_2.4

Test description p. 2135

8.3.2_2.4.1	Initial conditions p. 2135
8.3.2_2.4.2	Test procedure p. 2136
8.3.2_2.4.3	Message contents p. 2136

8.3.2_2.5

Test requirement p. 2138

8.3.3

E-UTRAN FDD-FDD Inter frequency event triggered reporting under AWGN propagation conditions in asynchronous cells with DRX when L3 filtering is used p. 2141

8.3.3.1

Test purpose p. 2141

8.3.3.2

Test applicability p. 2141

8.3.3.3

Minimum conformance requirements p. 2141

8.3.3.4

Test description p. 2142

8.3.3.4.1	Initial conditions p. 2142
8.3.3.4.2	Test procedure p. 2143
8.3.3.4.3	Message contents p. 2143

8.3.3.5

Test requirement p. 2146

8.3.3_2

E-UTRAN FDD-FDD inter-frequency event triggered reporting under AWGN propagation conditions in asynchronous cells with DRX when L3 filtering is used for UE category 1bis p. 2148

8.3.3_2.1

Test purpose p. 2148

8.3.3_2.2

Test applicability p. 2148

8.3.3_2.3

Minimum conformance requirements p. 2148

8.3.3_2.4

Test description p. 2149

8.3.3_2.4.1	Initial conditions p. 2149
8.3.3_2.4.2	Test procedure p. 2150
8.3.3_2.4.3	Message contents p. 2150

8.3.3_2.5

Test requirement p. 2153

8.3.4

E-UTRAN FDD - FDD Inter-frequency identification of a new CGI of E-UTRA cell using autonomous gaps p. 2155

8.3.4.1

Test purpose p. 2155

8.3.4.2

Test applicability p. 2155

8.3.4.3

Minimum conformance requirements p. 2155

8.3.4.4

Test description p. 2155

8.3.4.4.1	Initial conditions p. 2155
8.3.4.4.2	Test procedure p. 2156
8.3.4.4.3	Message contents p. 2157

8.3.4.5

Test requirement p. 2162

8.3.5

E-UTRAN FDD - FDD Inter-frequency identification of a new CGI of E-UTRA cell using autonomous gaps with DRX p. 2163

8.3.5.1

Test purpose p. 2163

8.3.5.2

Test applicability p. 2163

8.3.5.3

Minimum conformance requirements p. 2163

8.3.5.4

Test description p. 2164

8.3.5.4.1	Initial conditions p. 2164
8.3.5.4.2	Test procedure p. 2164
8.3.5.4.3	Message contents p. 2165

8.3.5.5

Test requirement p. 2170

8.3.6

E-UTRAN FDD-FDD Inter-frequency event triggered reporting without measurement gaps under AWGN propagation conditions in asynchronous cells p. 2171

8.3.6.1

Test purpose p. 2171

8.3.6.2

Test applicability p. 2171

8.3.6.3

Minimum conformance requirements p. 2171

8.3.6.4

Test description p. 2172

8.3.6.4.1	Initial conditions p. 2172
8.3.6.4.2	Test procedure p. 2173
8.3.6.4.3	Message contents p. 2174

8.3.6.5

Test requirement p. 2177

8.3.7

E-UTRAN FDD-FDD Inter-frequency event triggered reporting under fading propagation conditions in asynchronous cells for Increased Carrier Monitoring without Reduced Performance Group p. 2178

8.3.7.1

Test purpose p. 2178

8.3.7.2

Test applicability p. 2178

8.3.7.3

Minimum conformance requirements p. 2178

8.3.7.4

Test description p. 2180

8.3.7.4.1	Initial conditions p. 2180
8.3.7.4.2	Test procedure p. 2180
8.3.7.4.3	Message contents p. 2181

8.3.7.5

Test requirement p. 2182

8.3.8

FDD-FDD Inter-frequency correct reporting of measurement events with reduced performance group configured, non DRX p. 2184

8.3.8.1

Test purpose p. 2184

8.3.8.2

Test applicability p. 2184

8.3.8.3

Minimum conformance requirements p. 2185

8.3.8.4

Test description p. 2186

8.3.8.4.1	Initial conditions p. 2186
8.3.8.4.2	Test procedure p. 2187
8.3.8.4.3	Message contents p. 2187

8.3.8.5

Test requirement p. 2188

8.3.9

FDD-FDD Inter-frequency correct reporting of measurement events with reduced performance group configured, DRX p. 2191

8.3.9.1

Test purpose p. 2191

8.3.9.2

Test applicability p. 2191

8.3.9.3

Minimum conformance requirements p. 2191

8.3.9.4

Test description p. 2192

8.3.9.4.1	Initial conditions p. 2192
8.3.9.4.2	Test procedure p. 2193
8.3.9.4.3	Message contents p. 2194

8.3.9.5

Test requirement p. 2195

8.3.10_11

- p. 2196

8.3.12

E-UTRAN FDD-FDD Inter-frequency event triggered reporting under fading propagation conditions in asynchronous cells for CE UE with discontinuous MPDCCH monitoring in CEModeA p. 2196

8.3.12.1

Test purpose p. 2196

8.3.12.2

Test applicability p. 2196

8.3.12.3

Minimum conformance requirements p. 2196

8.3.12.4

Test description p. 2199

8.3.12.4.1	Initial conditions p. 2199
8.3.12.4.2	Test procedure p. 2199
8.3.12.4.3	Message contents p. 2200

8.3.12.5

Test requirement p. 2202

8.3.13

E-UTRAN HD-FDD Inter-frequency event triggered reporting under fading propagation conditions in asynchronous cells for CE UE with discontinuous MPDCCH monitoring in CEModeA p. 2203

8.3.13.1

Test purpose p. 2203

8.3.13.2

Test applicability p. 2203

8.3.13.3

Minimum conformance requirements p. 2203

8.3.13.4

Test description p. 2203

8.3.13.4.1	Initial conditions p. 2203
8.3.13.4.2	Test procedure p. 2203
8.3.13.4.3	Message contents p. 2203

8.3.13.5

Test requirement p. 2203

8.3.14

E-UTRAN FDD-FDD Inter-frequency event triggered reporting under fading propagation conditions in asynchronous cells for CE UE with discontinuous MPDCCH monitoring in CEModeB p. 2205

8.3.14.1

Test purpose p. 2205

8.3.14.2

Test applicability p. 2205

8.3.14.3

Minimum conformance requirements p. 2205

8.3.14.4

Test description p. 2207

8.3.14.4.1	Initial conditions p. 2207
8.3.14.4.2	Test procedure p. 2207
8.3.14.4.3	Message contents p. 2208

8.3.14.5

Test requirement p. 2210

8.3.15

E-UTRAN HD-FDD Inter-frequency event triggered reporting under fading propagation conditions in asynchronous cells for CE UE with discontinuous MPDCCH monitoring in CEModeB p. 2211

8.3.15.1

Test purpose p. 2211

8.3.15.2

Test applicability p. 2211

8.3.15.3

Minimum conformance requirements p. 2211

8.3.15.4

Test description p. 2211

8.3.15.4.1	Initial conditions p. 2211
8.3.15.4.2	Test procedure p. 2211
8.3.15.4.3	Message contents p. 2211

8.3.15.5

Test requirement p. 2211

8.3.16

E-UTRAN FDD-FDD Inter-frequency event triggered reporting under fading propagation conditions in asynchronous cells for CE UE in CEModeA when DRX is used p. 2213

8.3.16.1

Test purpose p. 2213

8.3.16.2

Test applicability p. 2213

8.3.16.3

Minimum conformance requirements p. 2213

8.3.16.4

Test description p. 2214

8.3.16.4.1	Initial conditions p. 2214
8.3.16.4.2	Test procedure p. 2215
8.3.16.4.3	Message contents p. 2216

8.3.16.5

Test requirement p. 2218

8.3.17

E-UTRAN HD-FDD Inter-frequency event triggered reporting under fading propagation conditions in asynchronous cells for CE UE in CEModeA when DRX is used p. 2220

8.3.17.1

Test purpose p. 2220

8.3.17.2

Test applicability p. 2220

8.3.17.3

Minimum conformance requirements p. 2220

8.3.17.4

Test description p. 2221

8.3.17.4.1	Initial conditions p. 2221
8.3.17.4.2	Test procedure p. 2221
8.3.17.4.3	Message contents p. 2221

8.3.17.5

Test requirement p. 2221

8.3.18

E-UTRAN FDD-FDD Inter-frequency event triggered reporting under fading propagation conditions in asynchronous cells for CE UE in CEModeB when DRX is used p. 2223

8.3.18.1

Test purpose p. 2223

8.3.18.2

Test applicability p. 2223

8.3.18.3

Minimum conformance requirements p. 2223

8.3.18.4

Test description p. 2225

8.3.18.4.1	Initial conditions p. 2225
8.3.18.4.2	Test procedure p. 2226
8.3.18.4.3	Message contents p. 2226

8.3.18.5

Test requirement p. 2229

8.3.19

E-UTRAN HD-FDD Inter-frequency event triggered reporting under fading propagation conditions in asynchronous cells for CE UE in CEModeB when DRX is used p. 2231

8.3.19.1

Test purpose p. 2231

8.3.19.2

Test applicability p. 2231

8.3.19.3

Minimum conformance requirements p. 2231

8.3.19.4

Test description p. 2232

8.3.19.4.1	Initial conditions p. 2232
8.3.19.4.2	Test procedure p. 2232
8.3.19.4.3	Message contents p. 2232

8.3.19.5

Test requirement p. 2232

8.4

E-UTRAN TDD-TDD inter frequency measurements p. 2234

8.4.1

E-UTRAN TDD-TDD Inter-frequency event triggered reporting under fading propagation conditions in synchronous cells p. 2234

8.4.1.1

Test purpose p. 2234

8.4.1.2

Test applicability p. 2234

8.4.1.3

Minimum conformance requirements p. 2235

8.4.1.4

Test description p. 2236

8.4.1.4.1	Initial conditions p. 2236
8.4.1.4.2	Test procedure p. 2237
8.4.1.4.3	Message contents p. 2237

8.4.1.5

Test requirement p. 2238

8.4.1_2

E-UTRAN TDD-TDD Inter-frequency event triggered reporting under fading propagation conditions in synchronous cells for UE category 1bis p. 2240

8.4.1_2.1

Test purpose p. 2240

8.4.1_2.2

Test applicability p. 2240

8.4.1_2.3

Minimum conformance requirements p. 2240

8.4.1_2.4

Test description p. 2241

8.4.1_2.4.1	Initial conditions p. 2241
8.4.1_2.4.2	Test procedure p. 2242
8.4.1_2.4.3	Message contents p. 2243

8.4.1_2.5

Test requirement p. 2244

8.4.2

E-UTRAN TDD-TDD Inter-frequency event triggered reporting when DRX is used under fading propagation conditions in synchronous cells p. 2245

8.4.2.1

Test purpose p. 2245

8.4.2.2

Test applicability p. 2245

8.4.2.3

Minimum conformance requirements p. 2245

8.4.2.4

Test description p. 2246

8.4.2.4.1	Initial conditions p. 2246
8.4.2.4.2	Test procedure p. 2247
8.4.2.4.3	Message contents p. 2248

8.4.2.5

Test requirement p. 2250

8.4.2_2

E-UTRAN TDD-TDD Inter-frequency event triggered reporting when DRX is used under fading propagation conditions in synchronous cells for UE category 1bis p. 2252

8.4.2_2.1

Test purpose p. 2252

8.4.2_2.2

Test applicability p. 2252

8.4.2_2.3

Minimum conformance requirements p. 2252

8.4.2_2.4

Test description p. 2254

8.4.2_2.4.1	Initial conditions p. 2254
8.4.2_2.4.2	Test procedure p. 2255
8.4.2_2.4.3	Message contents p. 2255

8.4.2_2.5

Test requirement p. 2258

8.4.3

E-UTRAN TDD-TDD inter-frequency event triggered reporting under AWGN propagation conditions in synchronous cells with DRX when L3 filtering is used p. 2260

8.4.3.1

Test purpose p. 2260

8.4.3.2

Test applicability p. 2260

8.4.3.3

Minimum conformance requirements p. 2260

8.4.3.4

Test description p. 2261

8.4.3.4.1	Initial conditions p. 2261
8.4.3.4.2	Test procedure p. 2262
8.4.3.4.3	Message contents p. 2263

8.4.3.5

Test requirement p. 2266

8.4.3_2

E-UTRAN TDD-TDD inter-frequency event triggered reporting under AWGN propagation conditions in synchronous cells with DRX when L3 filtering is used for UE category 1bis p. 2267

8.4.3_2.1

Test purpose p. 2267

8.4.3_2.2

Test applicability p. 2268

8.4.3_2.3

Minimum conformance requirements p. 2268

8.4.3_2.4

Test description p. 2269

8.4.3_2.4.1	Initial conditions p. 2269
8.4.3_2.4.2	Test procedure p. 2270
8.4.3_2.4.3	Message contents p. 2270

8.4.3_2.5

Test requirement p. 2273

8.4.4

E-UTRAN TDD - TDD Inter-frequency identification of a new CGI of E-UTRA cell using autonomous gaps p. 2275

8.4.4.1

Test purpose p. 2275

8.4.4.2

Test applicability p. 2275

8.4.4.3

Minimum conformance requirements p. 2275

8.4.4.4

Test description p. 2275

8.4.4.4.1	Initial conditions p. 2275
8.4.4.4.2	Test procedure p. 2276
8.4.4.4.3	Message contents p. 2277

8.4.4.5

Test requirement p. 2280

8.4.5

E-UTRAN TDD - TDD Inter-frequency identification of a new CGI of E-UTRA cell using autonomous gaps with DRX p. 2281

8.4.5.1

Test purpose p. 2281

8.4.5.2

Test applicability p. 2282

8.4.5.3

Minimum conformance requirements p. 2282

8.4.5.4

Test description p. 2282

8.4.5.4.1	Initial conditions p. 2282
8.4.5.4.2	Test procedure p. 2283
8.4.5.4.3	Message contents p. 2284

8.4.5.5

Test requirement p. 2288

8.4.6

E-UTRAN TDD-TDD Inter-frequency event triggered reporting for TDD UL/DL configuration 0 p. 2290

8.4.6.1

Test purpose p. 2290

8.4.6.2

Test applicability p. 2290

8.4.6.3

Minimum conformance requirements p. 2290

8.4.6.4

Test description p. 2291

8.4.6.4.1	Initial conditions p. 2291
8.4.6.4.2	Test procedure p. 2292
8.4.6.4.3	Message contents p. 2293

8.4.6.5

Test requirement p. 2294

8.4.6_2

E-UTRAN TDD-TDD Inter-frequency event triggered reporting for TDD UL/DL configuration 0 for UE category 1bis p. 2296

8.4.6_2.4

Test description p. 2297

8.4.6_2.4.1	Initial conditions p. 2297
8.4.6_2.4.2	Test procedure p. 2298
8.4.6_2.4.3	Message contents p. 2299

8.4.6_2.5

Test requirement p. 2300

8.4.7

E-UTRAN TDD-TDD Inter-frequency event triggered reporting under fading propagation conditions in asynchronous cells for Increased Carrier Monitoring without Reduced Performance Group p. 2301

8.4.7.1

Test purpose p. 2301

8.4.7.2

Test applicability p. 2301

8.4.7.3

Minimum conformance requirements p. 2301

8.4.7.4

Test description p. 2303

8.4.7.4.1	Initial conditions p. 2303
8.4.7.4.2	Test procedure p. 2304
8.4.7.4.3	Message contents p. 2304

8.4.7.5

Test requirement p. 2305

8.4.8

TDD-TDD Interfrequency correct reporting of measurement events with reduced performance group configured, non DRX p. 2308

8.4.8.1

Test purpose p. 2308

8.4.8.2

Test applicability p. 2308

8.4.8.3

Minimum conformance requirements p. 2308

8.4.8.4

Test description p. 2309

8.4.8.4.1	Initial conditions p. 2309
8.4.8.4.2	Test procedure p. 2310
8.4.8.4.3	Message contents p. 2311

8.4.8.5

Test requirement p. 2312

8.4.9

TDD-TDD Inter-frequency correct reporting of measurement events with reduced performance group configured, DRX p. 2314

8.4.9.1

Test purpose p. 2314

8.4.9.2

Test applicability p. 2314

8.4.9.3

Minimum conformance requirements p. 2314

8.4.9.4

Test description p. 2316

8.4.9.4.1	Initial conditions p. 2316
8.4.9.4.2	Test procedure p. 2316
8.4.9.4.3	Message contents p. 2317

8.4.9.5

Test requirement p. 2318

8.4.10

- p. 2320

8.4.11

- p. 2320

8.4.12

E-UTRAN TDD-TDD Inter-frequency event triggered reporting under fading propagation conditions in asynchronous cells for CE UE with discontinuous MPDCCH monitoring in CEModeA p. 2320

8.4.12.1

Test purpose p. 2320

8.4.12.2

Test applicability p. 2320

8.4.12.3

Minimum conformance requirements p. 2320

8.4.12.4

Test description p. 2322

8.4.12.4.1	Initial conditions p. 2322
8.4.12.4.2	Test procedure p. 2323
8.4.12.4.3	Message contents p. 2324

8.4.12.5

Test requirement p. 2326

8.4.13

E-UTRAN TDD-TDD Inter-frequency event triggered reporting under fading propagation conditions in asynchronous cells for CE UE with discontinuous MPDCCH monitoring in CEModeB p. 2327

8.4.13.1

Test purpose p. 2327

8.4.13.2

Test applicability p. 2327

8.4.13.3

Minimum conformance requirements p. 2327

8.4.13.4

Test description p. 2329

8.4.13.4.1	Initial conditions p. 2329
8.4.13.4.2	Test procedure p. 2330
8.4.13.4.3	Message contents p. 2330

8.4.13.5

Test requirement p. 2330

8.4.14

E-UTRAN TDD-TDD Inter-frequency event triggered reporting under fading propagation conditions in asynchronous cells for CE UE in CEModeA when DRX is used p. 2332

8.4.14.1

Test purpose p. 2332

8.4.14.2

Test applicability p. 2332

8.4.14.3

Minimum conformance requirements p. 2332

8.4.14.4

Test description p. 2333

8.4.14.4.1	Initial conditions p. 2333
8.4.14.4.2	Test procedure p. 2334
8.4.14.4.3	Message contents p. 2335

8.4.14.5

Test requirement p. 2337

8.4.15

E-UTRAN TDD-TDD Inter-frequency event triggered reporting under fading propagation conditions in asynchronous cells for CE UE in CEModeB when DRX is used p. 2339

8.4.15.1

Test purpose p. 2339

8.4.15.2

Test applicability p. 2339

8.4.15.3

Minimum conformance requirements p. 2339

8.4.15.4

Test description p. 2341

8.4.15.4.1	Initial conditions p. 2341
8.4.15.4.2	Test procedure p. 2342
8.4.15.4.3	Message contents p. 2342

8.4.15.5

Test requirement p. 2342

8.5

E-UTRAN FDD - UTRAN measurements p. 2345

8.5.1

E-UTRAN FDD - UTRAN FDD event triggered reporting under fading propagation conditions p. 2345

8.5.1.1

Test purpose p. 2345

8.5.1.2

Test applicability p. 2345

8.5.1.3

Minimum conformance requirements p. 2345

8.5.1.4

Test description p. 2346

8.5.1.4.1	Initial conditions p. 2346
8.5.1.4.2	Test procedure p. 2347
8.5.1.4.3	Message contents p. 2348

8.5.1.5

Test requirement p. 2349

8.5.2

E-UTRAN FDD - UTRAN FDD SON ANR cell search reporting under AWGN propagation conditions p. 2350

8.5.2.1

Test purpose p. 2350

8.5.2.2

Test applicability p. 2351

8.5.2.3

Minimum conformance requirements p. 2351

8.5.2.4

Test description p. 2351

8.5.2.4.1	Initial conditions p. 2351
8.5.2.4.2	Test procedure p. 2352
8.5.2.4.3	Message contents p. 2353

8.5.2.5

Test requirement p. 2355

8.5.3

E-UTRAN FDD - UTRAN FDD event triggered reporting when DRX is used under fading propagation conditions p. 2356

8.5.3.1

Test purpose p. 2356

8.5.3.2

Test applicability p. 2356

8.5.3.3

Minimum conformance requirements p. 2356

8.5.3.4

Test description p. 2357

8.5.3.4.1	Initial conditions p. 2357
8.5.3.4.2	Test procedure p. 2358
8.5.3.4.3	Message contents p. 2359

8.5.3.5

Test requirement p. 2361

8.5.4

E-UTRAN FDD - UTRAN FDD enhanced cell identification under AWGN propagation conditions p. 2363

8.5.4.1

Test purpose p. 2363

8.5.4.2

Test applicability p. 2364

8.5.4.3

Minimum conformance requirements p. 2364

8.5.4.4

Test description p. 2364

8.5.4.4.1	Initial conditions p. 2364
8.5.4.4.2	Test procedure p. 2365
8.5.4.4.3	Message contents p. 2365

8.5.4.5

Test requirement p. 2367

8.5.5

- p. 2368

8.5.6

E-UTRAN FDD - UTRAN FDD event triggered reporting without measurement gaps under AWGN propagation conditions p. 2369

8.5.6.2

Test applicability p. 2369

8.5.6.4

Test description p. 2370

8.5.6.4.1	Initial conditions p. 2370
8.5.6.4.2	Test procedure p. 2371

8.5.7

E-UTRAN FDD - UTRAN FDD event triggered reporting under fading propagation conditions for 5MHz Bandwidth p. 2375

8.5.7.1

Test purpose p. 2375

8.5.7.2

Test applicability p. 2375

8.5.7.3

Minimum conformance requirements p. 2375

8.5.7.4

Test description p. 2375

8.5.7.4.1	Initial conditions p. 2375
8.5.7.4.2	Test procedure p. 2376
8.5.7.4.3	Message contents p. 2376

8.5.7.5

Test requirement p. 2376

8.5.8

E-UTRA FDD InterRAT UTRA FDD correct reporting of measurement events with reduced performance group configured, non DRX p. 2376

8.5.8.1

Test purpose p. 2376

8.5.8.2

Test applicability p. 2377

8.5.8.3

Minimum conformance requirements p. 2377

8.5.8.4

Test description p. 2378

8.5.8.4.1	Initial conditions p. 2378
8.5.8.4.2	Test procedure p. 2379
8.5.8.4.3	Message contents p. 2379

8.5.8.5

Test requirement p. 2381

8.6

E-UTRAN TDD - UTRAN FDD measurements p. 2382

8.6.1

E-UTRAN TDD - UTRAN FDD event triggered reporting under fading propagation conditions p. 2382

8.6.1.1

Test purpose p. 2382

8.6.1.2

Test applicability p. 2382

8.6.1.3

Minimum conformance requirements p. 2382

8.6.1.4

Test description p. 2384

8.6.1.4.1	Initial conditions p. 2384
8.6.1.4.2	Test procedure p. 2385
8.6.1.4.3	Message contents p. 2385

8.6.1.5

Test requirement p. 2386

8.6.2

- p. 2388

8.6.3

E-UTRA TDD InterRAT UTRA FDD correct reporting of measurement events with reduced performance group configured, non DRX p. 2388

8.6.3.1

Test purpose p. 2388

8.6.3.2

Test applicability p. 2388

8.6.3.3

Minimum conformance requirements p. 2388

8.6.3.4

Test description p. 2389

8.6.3.4.1	Initial conditions p. 2389
8.6.3.4.2	Test procedure p. 2390
8.6.3.4.3	Message contents p. 2391

8.6.3.5

Test requirement p. 2393

8.7

E-UTRAN TDD - UTRAN measurements p. 2394

8.7.1

E-UTRAN TDD - UTRAN TDD event triggered reporting under fading propagation conditions p. 2394

8.7.1.1

Test purpose p. 2394

8.7.1.2

Test applicability p. 2394

8.7.1.3

Minimum conformance requirements p. 2394

8.7.1.4

Test description p. 2395

8.7.1.4.1	Initial conditions p. 2395
8.7.1.4.2	Test procedure p. 2396
8.7.1.4.3	Message contents p. 2397

8.7.1.5

Test requirement p. 2398

8.7.2

E-UTRAN TDD - UTRAN TDD cell search when DRX is used under fading propagation conditions p. 2400

8.7.2.1

Test purpose p. 2400

8.7.2.2

Test applicability p. 2400

8.7.2.3

Minimum conformance requirements p. 2400

8.7.2.4

Test description p. 2401

8.7.2.4.1	Initial conditions p. 2401
8.7.2.4.2	Test procedure p. 2402
8.7.2.4.3	Message contents p. 2403

8.7.2.5

Test requirement p. 2405

8.7.3

E-UTRAN TDD - UTRAN TDD SON ANR cell search reporting under AWGN propagation conditions p. 2408

8.7.3.1

Test purpose p. 2408

8.7.3.2

Test applicability p. 2408

8.7.3.3

Minimum conformance requirements p. 2408

8.7.3.4

Test description p. 2409

8.7.3.4.1	Initial conditions p. 2409
8.7.3.4.2	Test procedure p. 2409
8.7.3.4.3	Message contents p. 2410

8.7.3.5

Test requirement p. 2412

8.7.4

E-UTRAN TDD - UTRAN TDD enhanced cell identification under AWGN propagation conditions p. 2414

8.7.4.1

Test purpose p. 2414

8.7.4.2

Test applicability p. 2414

8.7.4.3

Minimum conformance requirements p. 2414

8.7.4.4

Test description p. 2414

8.7.4.4.1	Initial conditions p. 2414
8.7.4.4.2	Test procedure p. 2415
8.7.4.4.3	Message contents p. 2416

8.7.4.5

Test requirement p. 2418

8.7.5

E-UTRA TDD InterRAT UTRA TDD correct reporting of measurement events with reduced performance group configured, non DRX p. 2419

8.7.5.1

Test purpose p. 2419

8.7.5.2

Test applicability p. 2419

8.7.5.3

Minimum conformance requirements p. 2419

8.7.5.4

Test description p. 2420

8.7.5.4.1	Initial conditions p. 2420
8.7.5.4.2	Test procedure p. 2421
8.7.5.4.3	Message contents p. 2422

8.7.5.5

Test requirement p. 2424

8.7A

E-UTRA FDD - UTRA TDD Measurement p. 2425

8.7A.1

E-UTRA FDD InterRAT UTRA TDD correct reporting of measurement events with reduced performance group configured, non DRX p. 2425

8.7A.1.1

Test purpose p. 2425

8.7A.1.2

Test applicability p. 2425

8.7A.1.3

Minimum conformance requirements p. 2426

8.7A.1.4

Test description p. 2427

8.7A.1.4.1	Initial conditions p. 2427
8.7A.1.4.2	Test procedure p. 2428
8.7A.1.4.3	Message contents p. 2428

8.A7.1.5

Test requirement p. 2430

8.8

E-UTRAN FDD - GSM measurements p. 2431

8.8.1

E-UTRAN FDD - GSM event triggered reporting in AWGN p. 2431

8.8.1.1

Test purpose p. 2431

8.8.1.2

Test applicability p. 2431

8.8.1.3

Minimum conformance requirements p. 2431

8.8.1.4

Test description p. 2433

8.8.1.4.1	Initial conditions p. 2433
8.8.1.4.2	Test procedure p. 2434
8.8.1.4.3	Message contents p. 2435

8.8.1.5

Test requirement p. 2437

8.8.2

E-UTRAN FDD - GSM event triggered reporting when DRX is used in AWGN p. 2438

8.8.2.1

Test purpose p. 2438

8.8.2.2

Test applicability p. 2438

8.8.2.3

Minimum conformance requirements p. 2438

8.8.2.4

Test description p. 2440

8.8.2.4.1	Initial conditions p. 2440
8.8.2.4.2	Test procedure p. 2441
8.8.2.4.3	Message contents p. 2442

8.8.2.5

Test requirement p. 2444

8.9

E-UTRAN FDD - UTRAN TDD measurements p. 2446

8.9.1

E-UTRAN FDD - UTRAN TDD event triggered reporting under fading propagation conditions p. 2446

8.9.1.1

Test purpose p. 2446

8.9.1.2

Test applicability p. 2446

8.9.1.3

Minimum requirement p. 2446

8.9.1.4

Test description p. 2448

8.9.1.4.1	Initial conditions p. 2448
8.9.1.4.2	Test procedure p. 2448
8.9.1.4.3	Message contents p. 2449

8.9.1.5

Test requirement p. 2451

8.9.2

E-UTRAN FDD - UTRAN TDD enhanced cell identification under AWGN propagation conditions p. 2452

8.9.2.1

Test purpose p. 2452

8.9.2.2

Test applicability p. 2452

8.9.2.3

Minimum conformance requirements p. 2453

8.9.2.4

Test description p. 2453

8.9.2.4.1	Initial conditions p. 2453
8.9.2.4.2	Test procedure p. 2454
8.9.2.4.3	Message contents p. 2454

8.9.2.5

Test requirement p. 2456

8.10

E-UTRAN TDD - GSM measurements p. 2458

8.10.1

E-UTRAN TDD - GSM event triggered reporting in AWGN p. 2458

8.10.1.1

Test purpose p. 2458

8.10.1.2

Test applicability p. 2458

8.10.1.3

Minimum conformance requirements p. 2458

8.10.1.4

Test description p. 2460

8.10.1.4.1	Initial conditions p. 2460
8.10.1.4.2	Test procedure p. 2461
8.10.1.4.3	Message contents p. 2462

8.10.1.5

Test requirement p. 2464

8.10.2

E-UTRAN TDD-GSM event triggered reporting when DRX is used in AWGN p. 2465

8.10.2.1

Test purpose p. 2465

8.10.2.2

Test applicability p. 2465

8.10.2.3

Minimum conformance requirements p. 2465

8.10.2.4

Test description p. 2467

8.10.2.4.1	Initial conditions p. 2467
8.10.2.4.2	Test procedure p. 2468
8.10.2.4.3	Message contents p. 2469

8.10.2.5

Test requirement p. 2472

8.11

- p. 2475

8.11.1_4

- p. 2475

8.11.5

Combined E-UTRAN FDD - E-UTRA FDD and GSM cell search. E-UTRA cells in fading; GSM cell in static propagation conditions p. 2475

8.11.5.1

Test purpose p. 2475

8.11.5.2

Test applicability p. 2475

8.11.5.3

Minimum conformance requirements p. 2475

8.11.5.4

Test description p. 2478

8.11.5.4.1	Initial conditions p. 2478
8.11.5.4.2	Test procedure p. 2479
8.11.5.4.3	Message contents p. 2480

8.11.5.5

Test requirement p. 2484

8.11.6

Combined E-UTRAN TDD - E-UTRA TDD and GSM cell search. E UTRA cells in fading; GSM cell in static propagation conditions p. 2486

8.11.6.1

Test purpose p. 2486

8.11.6.2

Test applicability p. 2486

8.11.6.3

Minimum conformance requirements p. 2486

8.11.6.4

Test description p. 2489

8.11.6.4.1	Initial conditions p. 2489
8.11.6.4.2	Test procedure p. 2490
8.11.6.4.3	Message contents p. 2491

8.11.6.5

Test requirement p. 2495

8.12

Void p. …

8.13

Void p. …

8.14

E-UTRAN TDD - FDD Inter-frequency Measurements p. 2497

8.14.1

E-UTRAN TDD-FDD Inter-frequency event triggered reporting under fading propagation conditions in asynchronous cells p. 2497

8.14.1.1

Test purpose p. 2497

8.14.1.2

Test applicability p. 2497

8.14.1.3

Minimum conformance requirements p. 2497

8.14.1.4

Test description p. 2498

8.14.1.4.1	Initial conditions p. 2498
8.14.1.4.2	Test procedure p. 2499
8.14.1.4.3	Message contents p. 2500

8.14.1.5

Test requirement p. 2501

8.14.2

E-UTRAN TDD-FDD Inter-frequency event triggered reporting when DRX is used under fading propagation conditions in asynchronous cells p. 2502

8.14.2.1

Test purpose p. 2502

8.14.2.2

Test applicability p. 2502

8.14.2.3

Minimum conformance requirements p. 2502

8.14.2.4

Test description p. 2504

8.14.2.4.1	Initial conditions p. 2504
8.14.2.4.2	Test procedure p. 2505
8.14.2.4.3	Message contents p. 2505

8.14.2.5

Test requirement p. 2508

8.14.3

E-UTRAN TDD - FDD Inter-frequency identification of a new CGI of E-UTRA cell using autonomous gaps p. 2510

8.14.3.1

Test purpose p. 2510

8.14.3.2

Test applicability p. 2510

8.14.3.3

Minimum conformance requirements p. 2510

8.14.3.4

Test description p. 2511

8.14.3.4.1	Initial conditions p. 2511
8.14.3.4.2	Test procedure p. 2512
8.14.3.4.3	Message contents p. 2513

8.14.3.5

Test requirement p. 2516

8.15

E-UTRAN FDD - TDD Inter-frequency Measurements p. 2517

8.15.1

E-UTRAN FDD-TDD Inter-frequency event triggered reporting under fading propagation conditions in asynchronous cells p. 2517

8.15.1.1

Test purpose p. 2517

8.15.1.2

Test applicability p. 2517

8.15.1.3

Minimum conformance requirements p. 2517

8.15.1.4

Test description p. 2518

8.15.1.4.1	Initial conditions p. 2518
8.15.1.4.2	Test procedure p. 2519
8.15.1.4.3	Message contents p. 2520

8.15.1.5

Test requirement p. 2521

8.15.2

E-UTRAN FDD-TDD Inter-frequency event triggered reporting when DRX is used under fading propagation conditions in asynchronous cells p. 2522

8.15.2.1

Test purpose p. 2522

8.15.2.2

Test applicability p. 2522

8.15.2.3

Minimum conformance requirements p. 2522

8.15.2.4

Test description p. 2524

8.15.2.4.1	Initial conditions p. 2524
8.15.2.4.2	Test procedure p. 2525
8.15.2.4.3	Message contents p. 2525

8.15.2.5

Test requirement p. 2528

8.15.3

E-UTRAN FDD - TDD Inter-frequency identification of a new CGI of E-UTRA cell using autonomous gaps p. 2530

8.15.3.1

Test purpose p. 2530

8.15.3.2

Test applicability p. 2530

8.15.3.3

Minimum conformance requirements p. 2530

8.15.3.4

Test description p. 2530

8.15.3.4.1	Initial conditions p. 2530
8.15.3.4.2	Test procedure p. 2531
8.15.3.4.3	Message contents p. 2532

8.15.3.5

Test requirement p. 2536

8.16

E-UTRAN Carrier Aggregation Measurements p. 2537

8.16.1

E-UTRAN FDD event triggered reporting under deactivated SCell in non-DRX p. 2537

8.16.1.1

Test purpose p. 2537

8.16.1.2

Test applicability p. 2537

8.16.1.3

Minimum conformance requirements p. 2538

8.16.1.4

Test description p. 2538

8.16.1.4.1	Initial conditions p. 2538
8.16.1.4.2	Test procedure p. 2540
8.16.1.4.3	Message contents p. 2541

8.16.1.5

Test requirement p. 2544

8.16.2

E-UTRAN TDD event triggered reporting under deactivated SCell in non-DRX p. 2546

8.16.2.1

Test purpose p. 2546

8.16.2.2

Test applicability p. 2546

8.16.2.3

Minimum conformance requirements p. 2546

8.16.2.4

Test description p. 2547

8.16.2.4.1	Initial conditions p. 2547
8.16.2.4.2	Test procedure p. 2548
8.16.2.4.3	Message contents p. 2549

8.16.2.5

Test requirement p. 2552

8.16.3

E-UTRAN FDD-FDD Event triggered reporting on deactivated SCell with PCell interruption in non-DRX p. 2554

8.16.3.1

Test purpose p. 2554

8.16.3.2

Test applicability p. 2554

8.16.3.3

Minimum conformance requirements p. 2554

8.16.3.4

Test description p. 2555

8.16.3.4.1	Initial conditions p. 2555
8.16.3.4.2	Test procedure p. 2556
8.16.3.4.3	Message contents p. 2557

8.16.3.5

Test requirement p. 2558

8.16.4

E-UTRAN TDD-TDD Event triggered reporting on deactivated SCell with PCell interruption in non-DRX p. 2559

8.16.4.1

Test purpose p. 2559

8.16.4.2

Test applicability p. 2559

8.16.4.3

Minimum conformance requirements p. 2559

8.16.4.4

Test description p. 2560

8.16.4.4.1	Initial conditions p. 2560
8.16.4.4.2	Test procedure p. 2561
8.16.4.4.3	Message contents p. 2562

8.16.4.5

Test requirement p. 2562

8.16.5

E-UTRAN FDD event triggered reporting under deactivated SCell in non-DRX for 20 MHz bandwidth p. 2563

8.16.5.1

Test purpose p. 2563

8.16.5.2

Test applicability p. 2564

8.16.5.3

Minimum conformance requirements p. 2564

8.16.5.4

Test description p. 2564

8.16.5.4.1	Initial conditions p. 2564
8.16.5.4.2	Test procedure p. 2565
8.16.5.4.3	Message contents p. 2566

8.16.5.5

Test requirement p. 2570

8.16.6

E-UTRAN TDD event triggered reporting under deactivated SCell in non-DRX for 20 MHz bandwidth p. 2571

8.16.6.1

Test purpose p. 2571

8.16.6.2

Test applicability p. 2571

8.16.6.3

Minimum conformance requirements p. 2571

8.16.6.4

Test description p. 2572

8.16.6.4.1	Initial conditions p. 2572
8.16.6.4.2	Test procedure p. 2573
8.16.6.4.3	Message contents p. 2574

8.16.6.5

Test requirement p. 2577

8.16.7

E-UTRA FDD event triggered reporting on deactivated SCell with PCell interruption in non-DRX for 20 MHz bandwidth p. 2578

8.16.7.1

Test purpose p. 2578

8.16.7.2

Test applicability p. 2578

8.16.7.3

Minimum conformance requirements p. 2579

8.16.7.4

Test description p. 2579

8.16.7.4.1	Initial conditions p. 2579
8.16.7.4.2	Test procedure p. 2580
8.16.7.4.3	Message contents p. 2581

8.16.7.5

Test requirement p. 2582

8.16.8

E-UTRAN TDD event triggered reporting on deactivated SCell with PCell interruption in non-DRX for 20 MHz bandwidth p. 2583

8.16.8.1

Test purpose p. 2583

8.16.8.2

Test applicability p. 2583

8.16.8.3

Minimum conformance requirements p. 2583

8.16.8.4

Test description p. 2584

8.16.8.4.1	Initial conditions p. 2584
8.16.8.4.2	Test procedure p. 2584
8.16.8.4.3	Message contents p. 2585

8.16.8.5

Test requirement p. 2585

8.16.9

E-UTRAN FDD event triggered reporting under deactivated SCell in non-DRX for 10MHz+5MHz p. 2586

8.16.9.1

Test purpose p. 2586

8.16.9.2

Test applicability p. 2586

8.16.9.3

Minimum conformance requirements p. 2586

8.16.9.4

Test description p. 2587

8.16.9.4.1	Initial conditions p. 2587
8.16.9.4.2	Test procedure p. 2587
8.16.9.4.3	Message contents p. 2587

8.16.9.5

Test requirement p. 2587

8.16.10

E-UTRAN TDD event triggered reporting under deactivated SCell in non-DRX for 10MHz+5MHz p. 2588

8.16.10.1

Test purpose p. 2588

8.16.10.2

Test applicability p. 2588

8.16.10.3

Minimum conformance requirements p. 2589

8.16.10.4

Test description p. 2589

8.16.10.4.1	Initial conditions p. 2589
8.16.10.4.2	Test procedure p. 2589
8.16.10.4.3	Message contents p. 2589

8.16.10.5

Test requirement p. 2589

8.16.11

E-UTRAN FDD event triggered reporting on deactivating SCell with PCell interruption in non-DRX for 10MHz+5MHz p. 2590

8.16.11.1

Test purpose p. 2590

8.16.11.2

Test applicability p. 2591

8.16.11.3

Minimum conformance requirements p. 2591

8.16.11.4

Test description p. 2591

8.16.11.4.1	Initial conditions p. 2591
8.16.11.4.2	Test procedure p. 2592
8.16.11.4.3	Message contents p. 2592

8.16.11.5

Test requirement p. 2592

8.16.12

E-UTRAN TDD event triggered reporting on deactivating SCell with PCell interruption in non-DRX for 10MHz+5MHz p. 2592

8.16.12.1

Test purpose p. 2592

8.16.12.2

Test applicability p. 2592

8.16.12.3

Minimum conformance requirements p. 2592

8.16.12.4

Test description p. 2592

8.16.12.4.1	Initial conditions p. 2592
8.16.12.4.2	Test procedure p. 2593
8.16.12.4.3	Message contents p. 2593

8.16.12.5

Test requirement p. 2593

8.16.13

E-UTRAN FDD event triggered reporting under deactivated SCell in non-DRX for 5MHz+5MHz p. 2594

8.16.13.1

Test purpose p. 2594

8.16.13.2

Test applicability p. 2594

8.16.13.3

Minimum conformance requirements p. 2594

8.16.13.4

Test description p. 2594

8.16.13.4.1	Initial conditions p. 2594
8.16.13.4.2	Test procedure p. 2595
8.16.13.4.3	Message contents p. 2595

8.16.13.5

Test requirement p. 2595

8.16.14

E-UTRAN TDD event triggered reporting under deactivated SCell in non-DRX for 5MHz+5MHz bandwidth p. 2596

8.16.14.1

Test purpose p. 2596

8.16.14.2

Test applicability p. 2596

8.16.14.3

Minimum conformance requirements p. 2596

8.16.14.4

Test description p. 2596

8.16.14.4.1	Initial conditions p. 2596
8.16.14.4.2	Test procedure p. 2597
8.16.14.4.3	Message contents p. 2597

8.16.14.5

Test requirement p. 2597

8.16.15

E-UTRA FDD event triggered reporting on deactivated SCell with PCell interruption in non-DRX for 5MHz+5MHz bandwidth p. 2598

8.16.15.1

Test purpose p. 2598

8.16.15.2

Test applicability p. 2598

8.16.15.3

Minimum conformance requirements p. 2598

8.16.15.4

Test description p. 2598

8.16.15.4.1	Initial conditions p. 2598
8.16.15.4.2	Test procedure p. 2599
8.16.15.4.3	Message contents p. 2599

8.16.15.5

Test requirement p. 2599

8.16.16

E-UTRA TDD event triggered reporting on deactivated SCell with PCell interruption in non-DRX for 5MHz+5MHz bandwidth p. 2600

8.16.16.1

Test purpose p. 2600

8.16.16.2

Test applicability p. 2600

8.16.16.3

Minimum conformance requirements p. 2600

8.16.16.4

Test description p. 2600

8.16.16.4.1	Initial conditions p. 2600
8.16.16.4.2	Test procedure p. 2601
8.16.16.4.3	Message contents p. 2601

8.16.16.5

Test requirement p. 2601

8.16.17

E-UTRAN FDD activation and deactivation of known SCell in non-DRX p. 2601

8.16.17.1

Test purpose p. 2601

8.16.17.2

Test applicability p. 2601

8.16.17.3

Minimum conformance requirements p. 2602

8.16.17.4

Test description p. 2602

8.16.17.4.1	Initial conditions p. 2602
8.16.17.4.2	Test procedure p. 2603
8.16.17.4.3	Message contents p. 2605

8.16.17.5

Test requirement p. 2607

8.16.17A

E-UTRAN FDD activation and deactivation of known SCell in non-DRX for 20MHz +20MHz bandwidth p. 2609

8.16.17A.1

Test purpose p. 2609

8.16.17A.2

Test applicability p. 2609

8.16.17A.3

Minimum conformance requirements p. 2610

8.16.17A.4

Test description p. 2610

8.16.17A.4.1	Initial conditions p. 2610
8.16.17A.4.2	Test procedure p. 2610
8.16.17A.4.3	Message contents p. 2610

8.16.17A.5

Test requirement p. 2610

8.16.18

E-UTRAN TDD activation and deactivation of known SCell in non-DRX p. 2611

8.16.18.1

Test purpose p. 2611

8.16.18.2

Test applicability p. 2611

8.16.18.3

Minimum conformance requirements p. 2611

8.16.18.4

Test description p. 2612

8.16.18.4.1	Initial conditions p. 2612
8.16.18.4.2	Test procedure p. 2613
8.16.18.4.3	Message contents p. 2615

8.16.18.5

Test requirement p. 2617

8.16.18A

E-UTRAN TDD activation and deactivation of known SCell in non-DRX for 20MHz +20MHz bandwidth p. 2618

8.16.18A.1

Test purpose p. 2618

8.16.18A.2

Test applicability p. 2619

8.16.18A.3

Minimum conformance requirements p. 2619

8.16.18A.4

Test description p. 2619

8.16.18A.4.1	Initial conditions p. 2619
8.16.18A.4.2	Test procedure p. 2619
8.16.18A.4.3	Message contents p. 2619

8.16.18A.5

Test requirement p. 2619

8.16.19

- p. 2620

8.16.20

- p. 2620

8.16.21

E-UTRAN TDD event triggered reporting under deactivated SCell in non-DRX for 20MHz+10MHz bandwidth p. 2620

8.16.21.1

Test purpose p. 2620

8.16.21.2

Test applicability p. 2620

8.16.21.3

Minimum conformance requirements p. 2620

8.16.21.4

Test description p. 2620

8.16.21.4.1	Initial conditions p. 2620
8.16.21.4.2	Test procedure p. 2622
8.16.21.4.3	Message contents p. 2622

8.16.21.5

Test requirement p. 2622

8.16.22

E-UTRAN TDD event triggered reporting on deactivated SCell with PCell interruption in non-DRX for 20MHz+10MHz bandwidth p. 2623

8.16.22.1

Test purpose p. 2623

8.16.22.2

Test applicability p. 2624

8.16.22.3

Minimum conformance requirements p. 2624

8.16.22.4

Test description p. 2624

8.16.22.4.1	Initial conditions p. 2624
8.16.22.4.2	Test procedure p. 2625
8.16.22.4.3	Message contents p. 2625

8.16.22.5

Test requirement p. 2625

8.16.23

E-UTRAN TDD-FDD CA Event Triggered Reporting Under Deactivated SCell in Non-DRX with PCell in FDD p. 2626

8.16.23.1

Test purpose p. 2626

8.16.23.2

Test applicability p. 2626

8.16.23.3

Minimum conformance requirements p. 2626

8.16.23.4

Test description p. 2627

8.16.23.4.1	Initial conditions p. 2627
8.16.23.4.2	Test procedure p. 2628
8.16.23.4.3	Message contents p. 2629

8.16.23.5

Test requirement p. 2629

8.16.24

E-UTRAN TDD-FDD CA Event Triggered Reporting Under Deactivated SCell in Non-DRX with PCell in TDD p. 2630

8.16.24.1

Test purpose p. 2630

8.16.24.2

Test applicability p. 2630

8.16.24.3

Minimum conformance requirements p. 2630

8.16.24.4

Test description p. 2631

8.16.24.4.1	Initial conditions p. 2631
8.16.24.4.2	Test procedure p. 2632
8.16.24.4.3	Message contents p. 2632

8.16.24.5

Test requirement p. 2632

8.16.25

E-UTRAN TDD-FDD CA Event triggered reporting on deactivated SCell with PCell interruption in non-DRX with PCell in FDD p. 2634

8.16.25.1

Test purpose p. 2634

8.16.25.2

Test applicability p. 2634

8.16.25.3

Minimum conformance requirements p. 2634

8.16.25.4

Test description p. 2634

8.16.25.4.1	Initial conditions p. 2634
8.16.25.4.2	Test procedure p. 2635
8.16.25.4.3	Message contents p. 2635

8.16.25.5

Test requirement p. 2635

8.16.26

E-UTRAN TDD-FDD CA Event triggered reporting on deactivated SCell with PCell interruption in non-DRX with PCell in TDD p. 2636

8.16.26.1

Test purpose p. 2636

8.16.26.2

Test applicability p. 2636

8.16.26.3

Minimum conformance requirements p. 2637

8.16.26.4

Test description p. 2637

8.16.26.4.1	Initial conditions p. 2637
8.16.26.4.2	Test procedure p. 2638
8.16.26.4.3	Message contents p. 2638

8.16.26.5

Test requirement p. 2638

8.16.27_42

Void p. …

8.16.43_46

- p. 2639

8.16.47

2DL/2UL FDD CA activation and deactivation of known PUCCH SCell without valid TA in non-DRX p. 2639

8.16.47.1

Test purpose p. 2639

8.16.47.2

Test applicability p. 2639

8.16.47.3

Minimum conformance requirements p. 2639

8.16.47.4

Test description p. 2640

8.16.47.4.1	Initial conditions p. 2640
8.16.47.4.2	Test procedure p. 2641
8.16.47.4.3	Message contents p. 2643

8.16.47.5

Test requirement p. 2644

8.16.48

2DL/2UL TDD CA activation and deactivation of known PUCCH SCell without valid TA in non-DRX p. 2646

8.16.48.1

Test purpose p. 2646

8.16.48.2

Test applicability p. 2646

8.16.48.3

Minimum conformance requirements p. 2646

8.16.48.4

Test description p. 2646

8.16.48.4.1	Initial conditions p. 2646
8.16.48.4.2	Test procedure p. 2647
8.16.48.4.3	Message contents p. 2649

8.16.48.5

Test requirement p. 2651

8.16.49

2DL/2UL TDD-FDD CA (FDD PCell) activation and deactivation of known PUCCH SCell without valid TA in non-DRX p. 2653

8.16.49.1

Test purpose p. 2653

8.16.49.2

Test applicability p. 2653

8.16.49.3

Minimum conformance requirements p. 2653

8.16.49.4

Test description p. 2653

8.16.49.4.1	Initial conditions p. 2653
8.16.49.4.2	Test procedure p. 2654
8.16.49.4.3	Message contents p. 2655

8.16.49.5

Test requirement p. 2657

8.16.50

2DL/2UL TDD-FDD CA (TDD PCell) activation and deactivation of known PUCCH SCell without valid TA in non-DRX p. 2659

8.16.50.1

Test purpose p. 2659

8.16.50.2

Test applicability p. 2659

8.16.50.3

Minimum conformance requirements p. 2659

8.16.50.4

Test description p. 2659

8.16.50.4.1	Initial conditions p. 2659
8.16.50.4.2	Test procedure p. 2660
8.16.50.4.3	Message contents p. 2661

8.16.50.5

Test requirement p. 2663

8.16.51_78

Void p. …

8.16.79_82

- p. 2665

8.16.83

3 DL CA Event Triggered Reporting under Deactivated SCells in Non-DRX with generic duplex modes p. 2665

8.16.83.1

Test purpose p. 2665

8.16.83.2

Test applicability p. 2665

8.16.83.3

Minimum conformance requirements p. 2665

8.16.83.4

Test description p. 2666

8.16.83.4.1	Initial conditions p. 2666
8.16.83.4.2	Test procedure p. 2667
8.16.83.4.3	Message contents p. 2669

8.16.83.5

Test requirement p. 2675

8.16.84

3 DL CA Event Triggered Reporting on Deactivated SCell with PCell and SCell Interruptions in Non-DRX with generic duplex modes p. 2679

8.16.84.1

Test Purpose p. 2679

8.16.84.2

Test applicability p. 2679

8.16.84.3

Minimum conformance requirements p. 2679

8.16.84.4

Test description p. 2680

8.16.84.4.1	Initial conditions p. 2680
8.16.84.4.2	Test procedure p. 2681
8.16.84.4.3	Message contents p. 2682

8.16.84.5

Test Requirements p. 2685

8.16.85

3 DL CA Activation and Deactivation of Known SCell in Non-DRX with generic duplex modes p. 2688

8.16.85.1

Test Purpose p. 2688

8.16.85.2

Test applicability p. 2688

8.16.85.3

Minimum conformance requirements p. 2688

8.16.85.4

Test description p. 2689

8.16.85.4.1	Initial conditions p. 2689
8.16.85.4.2	Test procedure p. 2690
8.16.85.4.3	Message contents p. 2694

8.16.85.5

Test Requirements p. 2697

8.16.86

3 DL CA Activation and Deactivation of Unknown SCell in Non-DRX with generic duplex modes p. 2698

8.16.86.1

Test Purpose and Environment p. 2698

8.16.86.2

Test applicability p. 2699

8.16.86.3

Minimum conformance requirements p. 2699

8.16.86.4

Test description p. 2700

8.16.86.4.1	Initial conditions p. 2700
8.16.86.4.2	Test procedure p. 2701
8.16.86.4.3	Message contents p. 2705

8.16.86.5

Test Requirements p. 2707

8.16.87

4 DL CA Event Triggered Reporting under Deactivated SCells in Non-DRX with generic duplex modes p. 2709

8.16.87.1

Test purpose p. 2709

8.16.87.2

Test applicability p. 2709

8.16.87.3

Minimum conformance requirements p. 2709

8.16.87.4

Test description p. 2709

8.16.87.4.1	Initial conditions p. 2709
8.16.87.4.2	Test procedure p. 2711
8.16.87.4.3	Message contents p. 2712

8.16.87.5

Test requirement p. 2716

8.16.88

4 DL CA Event Triggered Reporting on Deactivated SCell with PCell and SCell Interruptions in Non-DRX with generic duplex modes p. 2720

8.16.88.1

Test purpose p. 2720

8.16.88.2

Test applicability p. 2720

8.16.88.3

Minimum conformance requirements p. 2720

8.16.88.4

Test description p. 2720

8.16.88.4.1	Initial conditions p. 2720
8.16.88.4.2	Test procedure p. 2721
8.16.88.4.3	Message contents p. 2722

8.16.88.5

Test requirement p. 2726

8.16.89

4 DL CA Activation and Deactivation of Known SCell in Non-DRX with generic duplex modes p. 2732

8.16.89.1

Test Purpose p. 2732

8.16.89.2

Test applicability p. 2732

8.16.89.3

Minimum conformance requirements p. 2732

8.16.89.4

Test description p. 2733

8.16.89.4.1	Initial conditions p. 2733
8.16.89.4.2	Test procedure p. 2734
8.16.89.4.3	Message contents p. 2740

8.16.89.5

Test Requirements p. 2742

8.16.90

4 DL CA Activation and Deactivation of Unknown SCell in Non-DRX with generic duplex modes p. 2745

8.16.90.1

Test Purpose p. 2745

8.16.90.2

Test applicability p. 2745

8.16.90.3

Minimum conformance requirements p. 2745

8.16.90.4

Test description p. 2746

8.16.90.4.1	Initial conditions p. 2746
8.16.90.4.2	Test procedure p. 2747
8.16.90.4.3	Message contents p. 2753

8.16.90.5

Test Requirements p. 2756

8.16.91

5 DL CA Event Triggered Reporting under Deactivated SCells in Non-DRX with generic duplex modes p. 2758

8.16.91.1

Test purpose p. 2758

8.16.91.2

Test applicability p. 2758

8.16.91.3

Minimum conformance requirements p. 2759

8.16.91.4

Test description p. 2759

8.16.91.4.1	Initial conditions p. 2759
8.16.91.4.2	Test procedure p. 2760
8.16.91.4.3	Message contents p. 2762

8.16.91.5

Test requirement p. 2766

8.16.92

5D LCA Event Triggered Reporting on Deactivated SCell with PCell and SCell Interruptions in Non-DRX with generic duplex modes p. 2769

8.16.92.1

Test purpose p. 2769

8.16.92.2

Test applicability p. 2769

8.16.92.3

Minimum conformance requirements p. 2770

8.16.92.4

Test description p. 2770

8.16.92.4.1	Initial conditions p. 2770
8.16.92.4.2	Test procedure p. 2771
8.16.92.4.3	Message contents p. 2772

8.16.92.5

Test requirement p. 2775

8.16.93

5 DL CA Activation and Deactivation of Known SCell in Non-DRX with generic duplex modes p. 2781

8.16.93.1

Test Purpose p. 2781

8.16.93.2

Test applicability p. 2781

8.16.93.3

Minimum conformance requirements p. 2782

8.16.93.4

Test description p. 2783

8.16.93.4.1	Initial conditions p. 2783
8.16.93.4.2	Test procedure p. 2784
8.16.93.4.3	Message contents p. 2791

8.16.93.5

Test Requirements p. 2795

8.16.94

5 DL CA Activation and Deactivation of Unknown SCell in Non-DRX with generic duplex modes p. 2799

8.16.94.1

Test Purpose p. 2799

8.16.94.2

Test applicability p. 2799

8.16.94.3

Minimum conformance requirements p. 2799

8.16.94.4

Test description p. 2800

8.16.94.4.1	Initial conditions p. 2800
8.16.94.4.2	Test procedure p. 2802
8.16.94.4.3	Message contents p. 2809

8.16.94.5

Test Requirements p. 2812

8.16.95

6 DL CA Event Triggered Reporting under Deactivated SCells in Non-DRX with generic duplex modes p. 2816

8.16.95.1

Test purpose p. 2816

8.16.95.2

Test applicability p. 2816

8.16.95.3

Minimum conformance requirements p. 2817

8.16.95.4

Test description p. 2817

8.16.95.4.1	Initial conditions p. 2817
8.16.95.4.2	Test procedure p. 2819
8.16.95.4.3	Message contents p. 2821

8.16.95.5

Test requirement p. 2827

8.16.96

6 DL CA Event Triggered Reporting on Deactivated SCell with PCell and SCell Interruptions in Non-DRX with generic duplex modes p. 2833

8.16.96.1

Test purpose p. 2833

8.16.96.2

Test applicability p. 2833

8.16.96.3

Minimum conformance requirements p. 2833

8.16.96.4

Test description p. 2834

8.16.96.4.1	Initial conditions p. 2834
8.16.96.4.2	Test procedure p. 2836
8.16.96.4.3	Message contents p. 2837

8.16.96.5

Test requirement p. 2843

8.16.97

6 DL CA Activation and Deactivation of Known SCell in Non-DRX with generic duplex modes p. 2849

8.16.97.1

Test purpose p. 2849

8.16.97.2

Test applicability p. 2849

8.16.97.3

Minimum conformance requirements p. 2849

8.16.97.4

Test description p. 2849

8.16.97.4.1	Initial conditions p. 2849
8.16.97.4.2	Test procedure p. 2852
8.16.97.4.3	Message contents p. 2859

8.16.97.5

Test requirement p. 2860

8.16.98

6 DL CA Activation and Deactivation of Unknown SCell in Non-DRX with generic duplex modes p. 2864

8.16.98.1

Test purpose p. 2864

8.16.98.2

Test applicability p. 2864

8.16.98.3

Minimum conformance requirements p. 2864

8.16.98.4

Test description p. 2864

8.16.98.4.1	Initial conditions p. 2864
8.16.98.4.2	Test procedure p. 2867
8.16.98.4.3	Message contents p. 2870

8.16.98.5

Test requirement p. 2872

8.16.99

7 DL CA Event Triggered Reporting under Deactivated SCells in Non-DRX with generic duplex modes p. 2876

8.16.99.1

Test purpose p. 2876

8.16.99.2

Test applicability p. 2876

8.16.99.3

Minimum conformance requirements p. 2876

8.16.99.4

Test description p. 2876

8.16.99.4.1	Initial conditions p. 2876
8.16.99.4.2	Test procedure p. 2879
8.16.99.4.3	Message contents p. 2881

8.16.99.5

Test requirement p. 2887

8.16.100

7 DL CA Event Triggered Reporting on Deactivated SCell with PCell and SCell Interruptions in Non-DRX with generic duplex modes p. 2894

8.16.100.1

Test purpose p. 2894

8.16.100.2

Test applicability p. 2894

8.16.100.3

Minimum conformance requirements p. 2894

8.16.100.4

Test description p. 2894

8.16.100.4.1	Initial conditions p. 2894
8.16.100.4.2	Test procedure p. 2896
8.16.100.4.3	Message contents p. 2897

8.16.100.5

Test requirement p. 2903

8.16.101

7 DL CA Activation and Deactivation of Known SCell in Non-DRX with generic duplex modes p. 2909

8.16.101.1

Test purpose p. 2909

8.16.101.2

Test applicability p. 2909

8.16.101.3

Minimum conformance requirements p. 2909

8.16.101.4

Test description p. 2910

8.16.101.4.1	Initial conditions p. 2910
8.16.101.4.2	Test procedure p. 2911
8.16.101.4.3	Message contents p. 2918

8.16.101.5

Test requirement p. 2918

8.16.102

7 DL CA Activation and Deactivation of Unknown SCell in Non-DRX with generic duplex modes p. 2924

8.16.102.1

Test purpose p. 2924

8.16.102.2

Test applicability p. 2924

8.16.102.3

Minimum conformance requirements p. 2924

8.16.102.4

Test description p. 2925

8.16.102.4.1	Initial conditions p. 2925
8.16.102.4.2	Test procedure p. 2926
8.16.102.4.3	Message contents p. 2930

8.16.102.5

Test requirement p. 2930

8.16.103

E-UTRAN FDD hibernation and activation of known SCell in non-DRX p. 2936

8.16.103.1

Test purpose p. 2936

8.16.103.2

Test applicability p. 2936

8.16.103.3

Minimum conformance requirements p. 2936

8.16.103.4

Test description p. 2937

8.16.103.4.1	Initial conditions p. 2937
8.16.103.4.2	Test procedure p. 2938
8.16.103.4.3	Message contents p. 2941

8.16.103.5

Test requirement p. 2944

8.16.103A

E-UTRAN TDD hibernation and activation of known SCell in non-DRX p. 2946

8.16.103A.1

Test purpose p. 2946

8.16.103A.2

Test applicability p. 2946

8.16.103A.3

Minimum conformance requirements p. 2946

8.16.103A.4

Test description p. 2947

8.16.103A.4.1	Initial conditions p. 2947
8.16.103A.4.2	Test procedure p. 2948
8.16.103A.4.3	Message contents p. 2952

8.16.103A.5

Test requirement p. 2954

8.16.104

E-UTRAN FDD hibernation and activation of unknown SCell in non-DRX p. 2956

8.16.104.1

Test purpose p. 2956

8.16.104.2

Test applicability p. 2956

8.16.104.3

Minimum conformance requirements p. 2956

8.16.104.4

Test description p. 2957

8.16.104.4.1	Initial conditions p. 2957
8.16.104.4.2	Test procedure p. 2958
8.16.104.4.3	Message contents p. 2961

8.16.104.5

Test requirement p. 2963

8.16.104A

E-UTRAN TDD hibernation and activation of unknown SCell in non-DRX p. 2966

8.16.104A.1

Test purpose p. 2966

8.16.104A.2

Test applicability p. 2966

8.16.104A.3

Minimum conformance requirements p. 2966

8.16.104A.4

Test description p. 2967

8.16.104A.4.1	Initial conditions p. 2967
8.16.104A.4.2	Test procedure p. 2968
8.16.104A.4.3	Message contents p. 2972

8.16.104A.5

Test requirement p. 2974

8.17

RSTD Measurements for E-UTRAN Carrier Aggregation p. 2977

8.18

E-UTRAN TDD - HRPD Measurements p. 2977

8.18.1

E-UTRAN TDD-HRPD event triggered reporting under fading propagation conditions p. 2977

8.18.1.1

Test purpose p. 2977

8.18.1.2

Test applicability p. 2977

8.18.1.3

Minimum requirement p. 2977

8.18.1.4

Test description p. 2977

8.18.1.4.1	Initial conditions p. 2977
8.18.1.4.2	Test procedure p. 2978
8.18.1.4.3	Message contents p. 2979

8.18.1.5

Test requirement p. 2981

8.19

E-UTRAN TDD - CDMA2000 1X Measurements p. 2983

8.19.1

E-UTRAN TDD-CDMA2000 1X event triggered reporting under fading propagation conditions p. 2983

8.19.1.1

Test purpose p. 2983

8.19.1.2

Test applicability p. 2983

8.19.1.3

Minimum conformance requirements p. 2983

8.19.1.4

Test description p. 2983

8.19.1.4.1	Initial conditions p. 2983
8.19.1.4.2	Test procedure p. 2984
8.19.1.4.3	Message contents p. 2985

8.19.1.5

Test requirement p. 2987

8.20

Inter-frequency/RAT Measurements in CA mode p. 2989

8.20.1

E-UTRAN FDD-FDD Inter-frequency event triggered reporting under fading propagation conditions in asynchronous cells p. 2989

8.20.1.1

Test purpose p. 2989

8.20.1.2

Test applicability p. 2989

8.20.1.3

Minimum conformance requirements p. 2989

8.20.1.4

Test description p. 2990

8.20.1.4.1	Initial conditions p. 2990
8.20.1.4.2	Test procedure p. 2991
8.20.1.4.3	Message contents p. 2992

8.20.1.5

Test requirement p. 2993

8.20.2

E-UTRAN TDD-TDD Inter-frequency event triggered reporting under fading propagation conditions in synchronous cells p. 2994

8.20.2.1

Test purpose p. 2994

8.20.2.2

Test applicability p. 2994

8.20.2.3

Minimum conformance requirements p. 2995

8.20.2.4

Test description p. 2996

8.20.2.4.1	Initial conditions p. 2996
8.20.2.4.2	Test procedure p. 2997
8.20.2.4.3	Message contents p. 2997

8.20.2.5

Test requirement p. 2999

8.20.2A

E-UTRAN TDD-TDD Inter-frequency event triggered reporting under fading propagation conditions in synchronous cells for 20 MHz +20 MHz bandwidth p. 3000

8.20.2A.1

Test purpose p. 3000

8.20.2A.2

Test applicability p. 3000

8.20.2A.3

Minimum conformance requirements p. 3000

8.20.2A.4

Test description p. 3000

8.20.2A.4.1	Initial conditions p. 3000
8.20.2A.4.2	Test procedure p. 3001
8.20.2A.4.3	Message contents p. 3001

8.20.2A.5

Test requirement p. 3001

8.20.2B

E-UTRAN TDD-TDD Inter-frequency event triggered reporting under fading propagation conditions in synchronous cells for 20 MHz +10 MHz bandwidth p. 3002

8.20.2B.1

Test purpose p. 3002

8.20.2B.2

Test applicability p. 3002

8.20.2B.3

Minimum conformance requirements p. 3002

8.20.2B.4

Test description p. 3002

8.20.2B.4.1	Initial conditions p. 3002
8.20.2B.4.2	Test procedure p. 3003
8.20.2B.4.3	Message contents p. 3003

8.20.2B.5

Test requirement p. 3003

8.20.3

E-UTRAN FDD - UTRAN FDD event triggered reporting under fading propagation conditions p. 3004

8.20.3.1

Test purpose p. 3004

8.20.3.2

Test applicability p. 3005

8.20.3.3

Minimum conformance requirements p. 3005

8.20.3.4

Test description p. 3006

8.20.3.4.1	Initial conditions p. 3006
8.20.3.4.2	Test procedure p. 3007
8.20.3.4.3	Message contents p. 3008

8.20.3.5

Test requirement p. 3010

8.20.4

E-UTRAN TDD to UTRAN TDD cell search under fading propagation conditions p. 3011

8.20.4.1

Test purpose p. 3011

8.20.4.2

Test applicability p. 3012

8.20.4.3

Minimum conformance requirements p. 3012

8.20.4.4

Test description p. 3013

8.20.4.4.1	Initial conditions p. 3013
8.20.4.4.2	Test procedure p. 3014
8.20.4.4.3	Message contents p. 3015

8.20.4.5

Test requirement p. 3017

8.20.4A

E-UTRAN TDD to UTRAN TDD cell search under fading propagation conditions for 20 MHz + 20 MHz bandwidth p. 3018

8.20.4A.1

Test purpose p. 3018

8.20.4A.2

Test applicability p. 3019

8.20.4A.3

Minimum conformance requirements p. 3019

8.20.4A.4

Test description p. 3019

8.20.4A.4.1	Initial conditions p. 3019
8.20.4A.4.2	Test procedure p. 3020
8.20.4A.4.3	Message contents p. 3020

8.20.4A.5

Test requirement p. 3020

8.20.4B

E-UTRAN TDD to UTRAN TDD cell search under fading propagation conditions for 20 MHz + 10 MHz bandwidth p. 3021

8.20.4B.1

Test purpose p. 3021

8.20.4B.2

Test applicability p. 3022

8.20.4B.3

Minimum conformance requirements p. 3022

8.20.4B.4

Test description p. 3022

8.20.4B.4.1	Initial conditions p. 3022
8.20.4B.4.2	Test procedure p. 3023
8.20.4B.4.3	Message contents p. 3023

8.20.4B.5

Test requirement p. 3023

8.21

Void p. …

8.22

E-UTRAN Discovery Signal Measurements p. 3025

8.22.1

E-UTRAN FDD-FDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells in DRX based on CRS based discovery signal p. 3025

8.22.1.1

Test purpose p. 3025

8.22.1.2

Test applicability p. 3025

8.22.1.3

Minimum conformance requirements p. 3025

8.22.1.4

Test description p. 3026

8.22.1.4.1	Initial conditions p. 3026
8.22.1.4.2	Test procedure p. 3026
8.22.1.4.3	Message contents p. 3027

8.22.1.5

Test requirement p. 3030

8.22.2

E-UTRAN TDD-TDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells in DRX based on CRS based discovery signal p. 3032

8.22.2.1

Test purpose p. 3032

8.22.2.2

Test applicability p. 3032

8.22.2.3

Minimum conformance requirements p. 3032

8.22.2.4

Test description p. 3033

8.22.2.4.1	Initial conditions p. 3033
8.22.2.4.2	Test procedure p. 3034
8.22.2.4.3	Message contents p. 3035

8.22.2.5

Test requirement p. 3037

8.22.3

E-UTRAN FDD-FDD inter-frequency event triggered reporting under fading propagation conditions in DRX based on CRS based discovery signal p. 3039

8.22.3.1

Test purpose p. 3039

8.22.3.2

Test applicability p. 3039

8.22.3.3

Minimum conformance requirements p. 3040

8.22.3.4

Test description p. 3041

8.22.3.4.1	Initial conditions p. 3041
8.22.3.4.2	Test procedure p. 3041
8.22.3.4.3	Message contents p. 3042

8.22.3.5

Test requirement p. 3045

8.22.4

E-UTRAN TDD-TDD inter-frequency event triggered reporting under fading propagation conditions in DRX based on CRS based discovery signal p. 3048

8.22.4.1

Test purpose p. 3048

8.22.4.2

Test applicability p. 3048

8.22.4.3

Minimum conformance requirements p. 3048

8.22.4.4

Test description p. 3049

8.22.4.4.1	Initial conditions p. 3049
8.22.4.4.2	Test procedure p. 3050
8.22.4.4.3	Message contents p. 3050

8.22.4.5

Test requirement p. 3053

8.22.5

E-UTRAN FDD-FDD intra-frequency event triggered reporting in DRX based on CSI-RS based discovery signal p. 3055

8.22.5.1

Test purpose p. 3055

8.22.5.2

Test applicability p. 3055

8.22.5.3

Minimum conformance requirements p. 3056

8.22.5.4

Test description p. 3057

8.22.5.4.1	Initial conditions p. 3057
8.22.5.4.2	Test procedure p. 3057
8.22.5.4.3	Message contents p. 3058

8.22.5.5

Test requirement p. 3061

8.22.6

E-UTRAN TDD-TDD intra-frequency event triggered reporting in DRX based on CSI-RS based discovery signal p. 3064

8.22.6.1

Test purpose p. 3064

8.22.6.2

Test applicability p. 3064

8.22.6.3

Minimum conformance requirements p. 3064

8.22.6.4

Test description p. 3065

8.22.6.4.1	Initial conditions p. 3065
8.22.6.4.2	Test procedure p. 3066
8.22.6.4.3	Message contents p. 3066

8.22.6.5

Test requirement p. 3070

8.22.7

E-UTRAN FDD-FDD Inter-frequency event triggered reporting in DRX based on CSI-RS based discovery signal p. 3072

8.22.7.1

Test purpose p. 3072

8.22.7.2

Test applicability p. 3072

8.22.7.3

Minimum conformance requirements p. 3072

8.22.7.4

Test description p. 3073

8.22.7.4.1	Initial conditions p. 3073
8.22.7.4.2	Test procedure p. 3074
8.22.7.4.3	Message contents p. 3075

8.22.7.5

Test requirement p. 3078

8.22.8

E-UTRAN TDD-TDD inter-frequency event triggered reporting under fading propagation condition in DRX based on CSI-RS based discovery signal p. 3080

8.22.8.1

Test purpose p. 3080

8.22.8.2

Test applicability p. 3080

8.22.8.3

Minimum conformance requirements p. 3081

8.22.8.4

Test description p. 3082

8.22.8.4.1	Initial conditions p. 3082
8.22.8.4.2	Test procedure p. 3082
8.22.8.4.3	Message contents p. 3083

8.22.8.5

Test requirement p. 3086

8.22.9

E-UTRAN FDD event triggered reporting under deactivated SCell in non-DRX based on CRS based discovery signal p. 3089

8.22.9.1

Test purpose p. 3089

8.22.9.2

Test applicability p. 3089

8.22.9.3

Minimum conformance requirements p. 3089

8.22.9.4

Test description p. 3090

8.22.9.4.1	Initial conditions p. 3090
8.22.9.4.2	Test procedure p. 3091
8.22.9.4.3	Message contents p. 3092

8.22.9.5

Test requirement p. 3095

8.22.10

E-UTRAN TDD event triggered reporting under deactivated SCell in non-DRX based on CRS based discovery signal p. 3097

8.22.10.1

Test purpose p. 3097

8.22.10.2

Test applicability p. 3097

8.22.10.3

Minimum conformance requirements p. 3097

8.22.10.4

Test description p. 3097

8.22.10.4.1	Initial conditions p. 3097
8.22.10.4.2	Test procedure p. 3098
8.22.10.4.3	Message contents p. 3098

8.22.10.5

Test requirement p. 3102

8.22.11

E-UTRAN FDD event triggered reporting under deactivated SCell in non-DRX based on CSI-RS based discovery signal p. 3104

8.22.11.1

Test purpose p. 3104

8.22.11.2

Test applicability p. 3104

8.22.11.3

Minimum conformance requirements p. 3104

8.22.11.4

Test description p. 3105

8.22.11.4.1	Initial conditions p. 3105
8.22.11.4.2	Test procedure p. 3106
8.22.11.4.3	Message contents p. 3107

8.22.11.5

Test requirement p. 3111

8.22.12

E-UTRAN TDD event triggered reporting under deactivated SCell in non-DRX based on CSI-RS based discovery signal p. 3113

8.22.12.1

Test purpose p. 3113

8.22.12.2

Test applicability p. 3113

8.22.12.3

Minimum conformance requirements p. 3113

8.22.12.4

Test description p. 3113

8.22.12.4.1	Initial conditions p. 3113
8.22.12.4.2	Test procedure p. 3114

8.22.12.5

Test requirement p. 3118

8.23

E-UTRAN Dual Connectivity Measurements p. 3120

8.23.1

E-UTRAN FDD-FDD DC intra-frequency event triggered reporting with DRX in synchronous DC p. 3120

8.23.1.1

Test purpose p. 3120

8.23.1.2

Test applicability p. 3120

8.23.1.3

Minimum conformance requirements p. 3120

8.23.1.4

Test description p. 3121

8.23.1.4.1	Initial conditions p. 3121
8.23.1.4.2	Test procedure p. 3122
8.23.1.4.3	Message contents p. 3123

8.23.1.5

Test requirement p. 3126

8.23.2

E-UTRAN FDD-FDD DC intra-frequency event triggered reporting with DRX in asynchronous DC p. 3128

8.23.2.1

Test purpose p. 3128

8.23.2.2

Test applicability p. 3128

8.23.2.3

Minimum conformance requirements p. 3128

8.23.2.4

Test description p. 3129

8.23.2.4.1	Initial conditions p. 3129
8.23.2.4.2	Test procedure p. 3130
8.23.2.4.3	Message contents p. 3130

8.23.2.5

Test requirement p. 3130

8.23.3

E-UTRAN TDD-TDD DC intra-frequency event triggered reporting with DRX in synchronous DC p. 3132

8.23.3.1

Test purpose p. 3132

8.23.3.2

Test applicability p. 3132

8.23.3.3

Minimum conformance requirements p. 3132

8.23.3.4

Test description p. 3133

8.23.3.4.1	Initial conditions p. 3133
8.23.3.4.2	Test procedure p. 3134
8.23.3.4.3	Message contents p. 3135

8.23.3.5

Test requirement p. 3135

8.23.4

E-UTRAN FDD-FDD DC inter-frequency event triggered reporting with DRX in synchronous DC p. 3137

8.23.4.1

Test purpose p. 3137

8.23.4.2

Test applicability p. 3137

8.23.4.3

Minimum conformance requirements p. 3137

8.23.4.4

Test description p. 3138

8.23.4.4.1	Initial conditions p. 3138
8.23.4.4.2	Test procedure p. 3139
8.23.4.4.3	Message contents p. 3140

8.23.4.5

Test requirement p. 3141

8.23.5

E-UTRAN FDD-FDD DC inter-frequency event triggered reporting with DRX in asynchronous DC p. 3143

8.23.5.1

Test purpose p. 3143

8.23.5.2

Test applicability p. 3144

8.23.5.3

Minimum conformance requirements p. 3144

8.23.5.4

Test description p. 3145

8.23.5.4.1	Initial conditions p. 3145
8.23.5.4.2	Test procedure p. 3146
8.23.5.4.3	Message contents p. 3146

8.23.5.5

Test requirement p. 3146

8.23.6

E-UTRAN TDD-TDD DC inter-frequency event triggered reporting with DRX in synchronous DC p. 3148

8.23.6.1

Test purpose p. 3148

8.23.6.2

Test applicability p. 3148

8.23.6.3

Minimum conformance requirements p. 3148

8.23.6.4

Test description p. 3150

8.23.6.4.1	Initial conditions p. 3150
8.23.6.4.2	Test procedure p. 3150
8.23.6.4.3	Message contents p. 3151

8.23.6.5

Test requirement p. 3152

8.23.7

E-UTRAN FDD-FDD Addition and Release Delay of known PSCell in Synchronous DC p. 3154

8.23.7.1

Test purpose p. 3154

8.23.7.2

Test applicability p. 3154

8.23.7.3

Minimum conformance requirements p. 3154

8.23.7.4

Test description p. 3155

8.23.7.4.1	Initial conditions p. 3155
8.23.7.4.2	Test procedure p. 3156
8.23.7.4.3	Message contents p. 3157

8.23.7.5

Test requirement p. 3157

8.23.8

E-UTRAN FDD-FDD Addition and Release Delay of known PSCell in Asynchronous DC p. 3159

8.23.8.1

Test purpose p. 3159

8.23.8.2

Test applicability p. 3159

8.23.8.3

Minimum conformance requirements p. 3159

8.23.8.4

Test description p. 3160

8.23.8.4.1	Initial conditions p. 3160
8.23.8.4.2	Test procedure p. 3161
8.23.8.4.3	Message contents p. 3162

8.23.8.5

Test requirement p. 3162

8.23.9

E-UTRAN TDD Addition and Release Delay of known PSCell in Synchronous DC p. 3164

8.23.9.1

Test purpose p. 3164

8.23.9.2

Test applicability p. 3164

8.23.9.3

Minimum conformance requirements p. 3164

8.23.9.4

Test description p. 3165

8.23.9.4.1	Initial conditions p. 3165
8.23.9.4.2	Test procedure p. 3166
8.23.9.4.3	Message contents p. 3167

8.23.9.5

Test requirement p. 3167

8.24

Proximity-based Services p. 3169

8.24.1

FFS p. 3169

8.24.2

FFS p. 3169

8.24.3

E-UTRAN FDD - Initiation/Cease of SLSS Transmission with ProSe Direct Discovery p. 3169

8.24.3.1

Test purpose p. 3169

8.24.3.2

Test applicability p. 3169

8.24.3.3

Minimum conformance requirements p. 3169

8.24.3.4

Test description p. 3170

8.24.3.4.1	Initial conditions p. 3170
8.24.3.4.2	Test procedure p. 3171
8.24.3.4.3	Message contents p. 3172

8.24.3.5

Test requirement p. 3172

8.25

E-UTRAN FDD-WLAN measurements p. 3173

8.25.1

E-UTRAN FDD-WLAN Event Triggered Reporting in non-DRX under AWGN p. 3173

8.25.1.1

Test purpose p. 3173

8.25.1.2

Test applicability p. 3173

8.25.1.3

Minimum conformance requirements p. 3173

8.25.1.4

Test description p. 3174

8.25.1.4.1	Initial conditions p. 3174
8.25.1.4.2	Test procedure p. 3175
8.25.1.4.3	Message contents p. 3175

8.25.1.5

Test requirement p. 3179

8.25.2

E-UTRAN TDD-WLAN Event Triggered Reporting in non-DRX under AWGN p. 3181

8.25.2.1

Test purpose p. 3181

8.25.2.2

Test applicability p. 3181

8.25.2.3

Minimum conformance requirements p. 3181

8.25.2.4

Test description p. 3182

8.25.2.4.1	Initial conditions p. 3182
8.25.2.4.2	Test procedure p. 3183
8.25.2.4.3	Message contents p. 3183

8.25.2.5

Test requirement p. 3187

8.26

Frame Structure 3 (FS3) p. 3189

8.26.1

E-UTRAN FDD-FS3 Activation and deactivation of known FS3 SCell with FDD PCell in non-DRX p. 3189

8.26.1.1

Test purpose p. 3189

8.26.1.2

Test applicability p. 3189

8.26.1.3

Minimum conformance requirements p. 3189

8.26.1.4

Test description p. 3190

8.26.1.4.1	Initial conditions p. 3190
8.26.1.4.2	Test procedure p. 3191
8.26.1.4.3	Message contents p. 3192

8.26.1.5

Test requirement p. 3196

8.26.2

E-UTRAN TDD-FS3 Activation and deactivation of known FS3 SCell with TDD PCell in non-DRX p. 3198

8.26.2.1

Test purpose p. 3198

8.26.2.2

Test applicability p. 3198

8.26.2.3

Minimum conformance requirements p. 3198

8.26.2.4

Test description p. 3198

8.26.2.4.1	Initial conditions p. 3198
8.26.2.4.2	Test procedure p. 3199
8.26.2.4.3	Message contents p. 3200

8.26.2.5

Test requirement p. 3201

8.26.3

E-UTRAN FDD-FS3 Event triggered reporting on deactivated FS3 SCell and FDD PCell interruption in non-DRX p. 3202

8.26.3.1

Test purpose p. 3202

8.26.3.2

Test applicability p. 3202

8.26.3.3

Minimum conformance requirements p. 3202

8.26.3.4

Test description p. 3204

8.26.3.4.1	Initial conditions p. 3204
8.26.3.4.2	Test procedure p. 3205
8.26.3.4.3	Message contents p. 3206

8.26.3.5

Test requirement p. 3208

8.26.3A

E-UTRAN FDD-FS3 3DL Event triggered reporting on deactivated FS3 SCell and FDD PCell interruption in non-DRX p. 3210

8.26.3A.1

Test purpose p. 3210

8.26.3A.2

Test applicability p. 3210

8.26.3A.3

Minimum conformance requirements p. 3210

8.26.3A.4

Test description p. 3212

8.26.3A.4.1	Initial conditions p. 3212
8.26.3A.4.2	Test procedure p. 3213
8.26.3A.4.3	Message contents p. 3214

8.26.3A.5

Test requirement p. 3217

8.26.4

E-UTRAN TDD-FS3 Event triggered reporting on deactivated FS3 SCell and TDD PCell interruption in non-DRX p. 3219

8.26.4.1

Test purpose p. 3219

8.26.4.2

Test applicability p. 3219

8.26.4.3

Minimum conformance requirements p. 3219

8.26.4.4

Test description p. 3219

8.26.4.4.1	Initial conditions p. 3219
8.26.4.4.2	Test procedure p. 3220
8.26.4.4.3	Message contents p. 3221

8.26.4.5

Test requirement p. 3221

8.26.4A

E-UTRAN TDD-FS3 3DL Event triggered reporting on deactivated FS3 SCell and TDD PCell interruption in non-DRX p. 3223

8.26.4A.1

Test purpose p. 3223

8.26.4A.2

Test applicability p. 3223

8.26.4A.3

Minimum conformance requirements p. 3223

8.26.4A.4

Test description p. 3225

8.26.4A.4.1	Initial conditions p. 3225
8.26.4A.4.2	Test procedure p. 3226
8.26.4A.4.3	Message contents p. 3227

8.26.4A.5

Test requirement p. 3230

8.26.5

E-UTRAN FDD-FS3 Intra-frequency event triggered reporting in non-DRX for CRS based discovery signal p. 3231

8.26.5.1

Test purpose p. 3231

8.26.5.2

Test applicability p. 3232

8.26.5.3

Minimum conformance requirements p. 3232

8.26.5.4

Test description p. 3233

8.26.5.4.1	Initial conditions p. 3233
8.26.5.4.2	Test procedure p. 3234
8.26.5.4.3	Message contents p. 3235

8.26.5.5

Test requirement p. 3236

8.26.5A

E-UTRAN FDD-FS3 Intra-frequency event triggered reporting in non-DRX for CRS based discovery signal with 2 SCells p. 3238

8.26.5A.1

Test purpose p. 3238

8.26.5A.2

Test applicability p. 3238

8.26.5A.3

Minimum conformance requirements p. 3238

8.26.5A.4

Test description p. 3240

8.26.5A.4.1	Initial conditions p. 3240
8.26.5A.4.2	Test procedure p. 3241
8.26.5A.4.3	Message contents p. 3241

8.26.5A.5

Test requirement p. 3242

8.26.6

E-UTRAN TDD-FS3 Intra-frequency event triggered reporting in non-DRX for CRS based discovery signal p. 3244

8.26.6.1

Test purpose p. 3244

8.26.6.2

Test applicability p. 3244

8.26.6.3

Minimum conformance requirements p. 3244

8.26.6.4

Test description p. 3246

8.26.6.4.1	Initial conditions p. 3246
8.26.6.4.2	Test procedure p. 3247
8.26.6.4.3	Message contents p. 3248

8.26.6.5

Test requirement p. 3248

8.26.6A

E-UTRAN TDD-FS3 Intra-frequency event triggered reporting in non-DRX for CRS based discovery signal with 2 SCells p. 3250

8.26.6A.1

Test purpose p. 3250

8.26.6A.2

Test applicability p. 3250

8.26.6A.3

Minimum conformance requirements p. 3250

8.26.6A.4

Test description p. 3250

8.26.6A.4.1	Initial conditions p. 3250
8.26.6A.4.2	Test procedure p. 3251
8.26.6A.4.3	Message contents p. 3252

8.26.6A.5

Test requirement p. 3252

8.26.7

E-UTRAN FDD-FS3 Intra-frequency event triggered reporting in DRX for CRS based discovery signal p. 3254

8.26.7.1

Test purpose p. 3254

8.26.7.2

Test applicability p. 3254

8.26.7.3

Minimum conformance requirements p. 3254

8.26.7.4

Test description p. 3256

8.26.7.4.1	Initial conditions p. 3256
8.26.7.4.2	Test procedure p. 3257
8.26.7.4.3	Message contents p. 3257

8.26.7.5

Test requirement p. 3259

8.26.8

E-UTRAN TDD-FS3 Intra-frequency event triggered reporting in DRX for CRS based discovery signal p. 3261

8.26.8.1

Test purpose p. 3261

8.26.8.2

Test applicability p. 3261

8.26.8.3

Minimum conformance requirements p. 3261

8.26.8.4

Test description p. 3263

8.26.8.4.1	Initial conditions p. 3263
8.26.8.4.2	Test procedure p. 3264
8.26.8.4.3	Message contents p. 3265

8.26.8.5

Test requirement p. 3267

8.26.9

E-UTRAN FDD-FS3 Inter-frequency event triggered reporting under fading propagation conditions in synchronous cells p. 3269

8.26.9.1

Test purpose p. 3269

8.26.9.2

Test applicability p. 3269

8.26.9.3

Minimum conformance requirements p. 3269

8.26.9.4

Test description p. 3270

8.26.9.4.1	Initial conditions p. 3270
8.26.9.4.2	Test procedure p. 3271
8.26.9.4.3	Message contents p. 3272

8.26.9.5

Test requirement p. 3274

8.26.10

E-UTRAN TDD-FS3 Inter-frequency event triggered reporting under fading propagation conditions in synchronous cells p. 3276

8.26.10.1

Test purpose p. 3276

8.26.10.2

Test applicability p. 3276

8.26.10.3

Minimum conformance requirements p. 3276

8.26.10.4

Test description p. 3277

8.26.10.4.1	Initial conditions p. 3277
8.26.10.4.2	Test procedure p. 3278
8.26.10.4.3	Message contents p. 3278

8.26.10.5

Test requirement p. 3280

Measurement Performance Requirements p. 3283

9.0

- p. 3283

9.1

RSRP p. 3284

9.1.1

FDD Intra frequency RSRP Accuracy p. 3284

9.1.1.1

FDD Intra Frequency Absolute RSRP Accuracy p. 3284

9.1.1.1.1	Test purpose p. 3284
9.1.1.1.2	Test applicability p. 3284
9.1.1.1.3	Minimum conformance requirements p. 3284
9.1.1.1.4	Test description p. 3285
9.1.1.1.5	Test requirement p. 3286

9.1.1.1_1

FDD Intra Frequency Absolute RSRP Accuracy (Rel 12 and forward) p. 3288

9.1.1.1_1.1	Test purpose p. 3288
9.1.1.1_1.2	Test applicability p. 3288
9.1.1.1_1.3	Minimum conformance requirements p. 3289
9.1.1.1_1.4	Test description p. 3290
9.1.1.1_1.5	Test requirement p. 3290

9.1.1.1_2

FDD Intra Frequency Absolute RSRP Accuracy for UE category 1bis p. 3292

9.1.1.1_2.1	Test purpose p. 3292
9.1.1.1_2.2	Test applicability p. 3292
9.1.1.1_2.3	Minimum conformance requirements p. 3292
9.1.1.1_2.4	Test description p. 3293
9.1.1.1_2.5	Test requirement p. 3295

9.1.1.1_3

FDD Intra Frequency Absolute RSRP Accuracy for CA Idle Mode Measurements p. 3297

9.1.1.2

FDD Intra Frequency Relative Accuracy of RSRP p. 3304

9.1.1.2.1	Test purpose p. 3304
9.1.1.2.2	Test applicability p. 3304
9.1.1.2.3	Minimum conformance requirements p. 3304
9.1.1.2.4	Test description p. 3305
9.1.1.2.5	Test requirement p. 3307

9.1.1.2_2

FDD Intra Frequency Relative Accuracy of RSRP for UE category 1bis p. 3308

9.1.1.2_2.1	Test purpose p. 3308
9.1.1.2_2.2	Test applicability p. 3308
9.1.1.2_2.3	Minimum conformance requirements p. 3309
9.1.1.2_2.4	Test description p. 3309
9.1.1.2_2.5	Test requirement p. 3311

9.1.2

TDD Intra frequency RSRP Accuracy p. 3312

9.1.2.1

TDD Intra Frequency Absolute RSRP Accuracy p. 3312

9.1.2.1.1	Test purpose p. 3312
9.1.2.1.2	Test applicability p. 3312
9.1.2.1.3	Minimum conformance requirements p. 3313
9.1.2.1.4	Test description p. 3314
9.1.2.1.5	Test requirement p. 3315

9.1.2.1_1

TDD Intra Frequency Absolute RSRP Accuracy (Rel 12 and forward) p. 3316

9.1.2.1_1.1	Test purpose p. 3316
9.1.2.1_1.2	Test applicability p. 3317
9.1.2.1_1.3	Minimum conformance requirements p. 3317
9.1.2.1_1.4	Test description p. 3318
9.1.2.1_1.5	Test requirement p. 3318

9.1.2.1_2

TDD Intra Frequency Absolute RSRP Accuracy for UE category 1bis p. 3319

9.1.2.1_2.1	Test purpose p. 3319
9.1.2.1_2.2	Test applicability p. 3319
9.1.2.1_2.3	Minimum conformance requirements p. 3319
9.1.2.1_2.4	Test description p. 3320
9.1.2.1_2.5	Test requirement p. 3322

9.1.2.2

TDD Intra Frequency Relative Accuracy of RSRP p. 3323

9.1.2.2.1	Test purpose p. 3323
9.1.2.2.2	Test applicability p. 3323
9.1.2.2.3	Minimum conformance requirements p. 3323
9.1.2.2.4	Test description p. 3324
9.1.2.2.5	Test requirement p. 3325

9.1.2.2_2

TDD Intra Frequency Relative Accuracy of RSRP for UE category 1bis p. 3327

9.1.2.2_2.1	Test purpose p. 3327
9.1.2.2_2.2	Test applicability p. 3327
9.1.2.2_2.3	Minimum conformance requirements p. 3327
9.1.2.2_2.4	Test description p. 3328
9.1.2.2_2.5	Test requirement p. 3329

9.1.3

FDD Inter frequency RSRP Accuracy p. 3331

9.1.3.1

FDD - FDD Inter Frequency Absolute RSRP Accuracy p. 3331

9.1.3.1.1	Test purpose p. 3331
9.1.3.1.2	Test applicability p. 3331
9.1.3.1.3	Minimum conformance requirements p. 3331
9.1.3.1.4	Test description p. 3332
9.1.3.1.5	Test requirement p. 3333

9.1.3.1_1

FDD - FDD Inter Frequency Absolute RSRP Accuracy (Rel 12 and forward) p. 3335

9.1.3.1_1.1	Test purpose p. 3335
9.1.3.1_1.2	Test applicability p. 3335
9.1.3.1_1.3	Minimum conformance requirements p. 3335
9.1.3.1_1.4	Test description p. 3336
9.1.3.1_1.5	Test requirement p. 3336

9.1.3.1_2

FDD - FDD Inter Frequency Absolute RSRP Accuracy for UE category 1bis p. 3338

9.1.3.1_2.1	Test purpose p. 3338
9.1.3.1_2.2	Test applicability p. 3339
9.1.3.1_2.3	Minimum conformance requirements p. 3339
9.1.3.1_2.4	Test description p. 3339
9.1.3.1_2.5	Test requirement p. 3341

9.1.3.1_3

FDD-FDD Inter Frequency Absolute RSRP Accuracy for CA Idle Mode Measurements for Overlapping Carrier p. 3343

9.1.3.1_4

FDD-FDD Inter Frequency Absolute RSRP Accuracy for CA Idle Mode Measurements for Non-Overlapping Carrier p. 3351

9.1.3.2

FDD - FDD Inter Frequency Relative Accuracy of RSRP p. 3358

9.1.3.2.1	Test purpose p. 3358
9.1.3.2.2	Test applicability p. 3358
9.1.3.2.3	Minimum conformance requirements p. 3358
9.1.3.2.4	Test description p. 3359
9.1.3.2.5	Test requirement p. 3361

9.1.3.2_1

FDD - FDD Inter Frequency Relative Accuracy of RSRP (Rel 12 and forward) p. 3362

9.1.3.2_1.1	Test purpose p. 3362
9.1.3.2_1.2	Test applicability p. 3362
9.1.3.2_1.3	Minimum conformance requirements p. 3362
9.1.3.2_1.4	Test description p. 3363
9.1.3.2_1.5	Test requirement p. 3363

9.1.3.2_2

FDD - FDD Inter Frequency Relative Accuracy of RSRP for UE category 1bis p. 3365

9.1.3.2_2.1	Test purpose p. 3365
9.1.3.2_2.2	Test applicability p. 3365
9.1.3.2_2.3	Minimum conformance requirements p. 3365
9.1.3.2_2.4	Test description p. 3366
9.1.3.2_2.5	Test requirement p. 3368

9.1.4

TDD Inter frequency RSRP Accuracy p. 3369

9.1.4.1

TDD - TDD Inter Frequency Absolute RSRP Accuracy p. 3369

9.1.4.1.1	Test purpose p. 3369
9.1.4.1.2	Test applicability p. 3369
9.1.4.1.3	Minimum conformance requirements p. 3369
9.1.4.1.4	Test description p. 3370
9.1.4.1.5	Test requirement p. 3372

9.1.4.1_1

TDD - TDD Inter Frequency Absolute RSRP Accuracy (Rel 12 and forward) p. 3373

9.1.4.1_1.1	Test purpose p. 3373
9.1.4.1_1.2	Test applicability p. 3373
9.1.4.1_1.3	Minimum conformance requirements p. 3373
9.1.4.1_1.4	Test description p. 3374
9.1.4.1_1.5	Test requirement p. 3375

9.1.4.1_2

TDD - TDD Inter Frequency Absolute RSRP Accuracy for UE category 1bis p. 3377

9.1.4.1_2.1	Test purpose p. 3377
9.1.4.1_2.2	Test applicability p. 3377
9.1.4.1_2.3	Minimum conformance requirements p. 3377
9.1.4.1_2.4	Test description p. 3378
9.1.4.1_2.5	Test requirement p. 3380

9.1.4.2

TDD - TDD Inter Frequency Relative Accuracy of RSRP p. 3381

9.1.4.2.1	Test purpose p. 3381
9.1.4.2.2	Test applicability p. 3381
9.1.4.2.3	Minimum conformance requirements p. 3381
9.1.4.2.4	Test description p. 3382
9.1.4.2.5	Test requirement p. 3384

9.1.4.2_1

TDD - TDD Inter Frequency Relative Accuracy of RSRP (Rel 12 and forward) p. 3385

9.1.4.2_1.1	Test purpose p. 3385
9.1.4.2_1.2	Test applicability p. 3385
9.1.4.2_1.3	Minimum conformance requirements p. 3385
9.1.4.2_1.4	Test description p. 3386
9.1.4.2_1.5	Test requirement p. 3387

9.1.4.2_2

TDD - TDD Inter Frequency Relative Accuracy of RSRP for UE category 1bis p. 3389

9.1.4.2_2.1	Test purpose p. 3389
9.1.4.2_2.2	Test applicability p. 3389
9.1.4.2_2.3	Minimum conformance requirements p. 3389
9.1.4.2_2.4	Test description p. 3390
9.1.4.2_2.5	Test requirement p. 3391

9.1.5

FDD - TDD Inter frequency RSRP Accuracy p. 3393

9.1.5.1

FDD - TDD Inter Frequency Absolute RSRP Accuracy p. 3393

9.1.5.1.1	Test purpose p. 3393
9.1.5.1.2	Test applicability p. 3393
9.1.5.1.3	Minimum conformance requirements p. 3393
9.1.5.1.4	Test description p. 3394
9.1.5.1.5	Test requirement p. 3396

9.1.5.1_1

FDD - TDD Inter Frequency Absolute RSRP Accuracy (Rel 12 and forward) p. 3397

9.1.5.1_1.1	Test purpose p. 3397
9.1.5.1_1.2	Test applicability p. 3398
9.1.5.1_1.3	Minimum conformance requirements p. 3398
9.1.5.1_1.4	Test description p. 3399
9.1.5.1_1.5	Test requirement p. 3399

9.1.5.1_2

FDD - TDD Inter Frequency Absolute RSRP Accuracy for UE category 1bis p. 3401

9.1.5.1_2.1	Test purpose p. 3401
9.1.5.1_2.2	Test applicability p. 3401
9.1.5.1_2.3	Minimum conformance requirements p. 3401
9.1.5.1_2.4	Test description p. 3402
9.1.5.1_2.5	Test requirement p. 3403

9.1.5.2

FDD - TDD Inter Frequency Relative Accuracy of RSRP p. 3405

9.1.5.2.1	Test purpose p. 3405
9.1.5.2.2	Test applicability p. 3405
9.1.5.2.3	Minimum conformance requirements p. 3406
9.1.5.2.4	Test description p. 3406
9.1.5.2.5	Test requirement p. 3408

9.1.5.2_1

FDD - TDD Inter Frequency Relative Accuracy of RSRP (Rel 12 and forward) p. 3410

9.1.5.2_1.1	Test purpose p. 3410
9.1.5.2_1.2	Test applicability p. 3410
9.1.5.2_1.3	Minimum conformance requirements p. 3410
9.1.5.2_1.4	Test description p. 3411
9.1.5.2_1.5	Test requirement p. 3411

9.1.5.2_2

FDD - TDD Inter Frequency Relative Accuracy of RSRP for UE category 1bis p. 3413

9.1.5.2_2.1	Test purpose p. 3413
9.1.5.2_2.2	Test applicability p. 3413
9.1.5.2_2.3	Minimum conformance requirements p. 3413
9.1.5.2_2.4	Test description p. 3414
9.1.5.2_2.5	Test requirement p. 3416

9.1.6

FDD RSRP Accuracy E-UTRA for Carrier Aggregation p. 3418

9.1.6.1

FDD Absolute RSRP Accuracy E-UTRA for Carrier Aggregation p. 3418

9.1.6.1.1	Test purpose p. 3418
9.1.6.1.2	Test applicability p. 3418
9.1.6.1.3	Minimum conformance requirements p. 3418
9.1.6.1.4	Test description p. 3419
9.1.6.1.5	Test requirement p. 3420

9.1.6.1_1

FDD Absolute RSRP Accuracy E-UTRA for Carrier Aggregation (Rel 12 and forward) p. 3422

9.1.6.1_1.1	Test purpose p. 3422
9.1.6.1_1.2	Test applicability p. 3422
9.1.6.1_1.3	Minimum conformance requirements p. 3422
9.1.6.1_1.4	Test description p. 3423
9.1.6.1_1.5	Test requirement p. 3424

9.1.6.2

FDD Relative RSRP Accuracy E-UTRA for Carrier Aggregation p. 3426

9.1.6.2.1	Test purpose p. 3426
9.1.6.2.2	Test applicability p. 3426
9.1.6.2.3	Minimum conformance requirements p. 3426
9.1.6.2.4	Test description p. 3427
9.1.6.2.5	Test requirement p. 3428

9.1.6.2_1

FDD Relative RSRP Accuracy E-UTRA for Carrier Aggregation (Rel-12 and forward) p. 3430

9.1.6.2_1.1	Test purpose p. 3430
9.1.6.2_1.2	Test applicability p. 3430
9.1.6.2_1.3	Minimum conformance requirements p. 3430
9.1.6.2_1.4	Test description p. 3432
9.1.6.2_1.5	Test requirement p. 3432

9.1.7

TDD RSRP Accuracy E-UTRA for Carrier Aggregation p. 3434

9.1.7.1

TDD Absolute RSRP Accuracy E-UTRA for Carrier Aggregation p. 3434

9.1.7.1.1	Test purpose p. 3434
9.1.7.1.2	Test applicability p. 3434
9.1.7.1.3	Minimum conformance requirements p. 3434
9.1.7.1.4	Test description p. 3435
9.1.7.1.5	Test requirement p. 3437

9.1.7.1_1

TDD Absolute RSRP Accuracy E-UTRA for Carrier Aggregation (Rel 12 and forward) p. 3438

9.1.7.1_1.1	Test purpose p. 3438
9.1.7.1_1.2	Test applicability p. 3438
9.1.7.1_1.3	Minimum conformance requirements p. 3439
9.1.7.1_1.4	Test description p. 3440
9.1.7.1_1.5	Test requirement p. 3440

9.1.7.2

TDD Relative RSRP Accuracy E-UTRA for Carrier Aggregation p. 3442

9.1.7.2.1	Test purpose p. 3442
9.1.7.2.2	Test applicability p. 3442
9.1.7.2.3	Minimum conformance requirements p. 3442
9.1.7.2.4	Test description p. 3443
9.1.7.2.5	Test requirement p. 3444

9.1.7.2_1

TDD Relative RSRP Accuracy E-UTRA for Carrier Aggregation (Rel-12 and forward) p. 3446

9.1.7.2_1.1	Test purpose p. 3446
9.1.7.2_1.2	Test applicability p. 3446
9.1.7.2_1.3	Minimum conformance requirements p. 3446
9.1.7.2_1.4	Test description p. 3448
9.1.7.2_1.5	Test requirement p. 3448

9.1.8

FDD RSRP Accuracy E-UTRA under Time-Domain Measurement Resource Restriction with Non-MBSFN ABS (eICIC) p. 3450

9.1.8.1

FDD Absolute RSRP Accuracy under Time-Domain Measurement Resource Restriction with Non-MBSFN ABS (eICIC) p. 3450

9.1.8.1.1	Test purpose p. 3450
9.1.8.1.2	Test applicability p. 3450
9.1.8.1.3	Minimum conformance requirements p. 3450
9.1.8.1.4	Test description p. 3451
9.1.8.1.5	Test requirement p. 3454

9.1.8.1_1

FDD Absolute RSRP Accuracy under Time-Domain Measurement Resource Restriction with Non-MBSFN ABS (eICIC) (Rel-12 and forward) p. 3456

9.1.8.1_1.1	Test purpose p. 3456
9.1.8.1_1.2	Test applicability p. 3456
9.1.8.1_1.3	Minimum conformance requirements p. 3456
9.1.8.1_1.4	Test description p. 3457
9.1.8.1_1.5	Test requirement p. 3458

9.1.8.2

FDD Relative RSRP Accuracy under Time-Domain Measurement Resource Restriction with Non-MBSFN ABS (eICIC) p. 3460

9.1.8.2.1	Test purpose p. 3460
9.1.8.2.2	Test applicability p. 3460
9.1.8.2.3	Minimum conformance requirements p. 3460
9.1.8.2.4	Test description p. 3461
9.1.8.2.5	Test requirement p. 3464

9.1.9

TDD RSRP Accuracy E-UTRA under Time-Domain Measurement Resource Restriction with Non-MBSFN ABS (eICIC) p. 3466

9.1.9.1

TDD Absolute RSRP Accuracy under Time-Domain Measurement Resource Restriction with Non-MBSFN ABS (eICIC) p. 3466

9.1.9.1.1	Test purpose p. 3466
9.1.9.1.2	Test applicability p. 3466
9.1.9.1.3	Minimum conformance requirements p. 3466
9.1.9.1.4	Test description p. 3467
9.1.9.1.5	Test requirement p. 3470

9.1.9.1_1

TDD Absolute RSRP Accuracy under Time-Domain Measurement Resource Restriction with Non-MBSFN ABS (eICIC) (Rel 12 and forward) p. 3472

9.1.9.1_1.1	Test purpose p. 3472
9.1.9.1_1.2	Test applicability p. 3472
9.1.9.1_1.3	Minimum conformance requirements p. 3472
9.1.9.1_1.4	Test description p. 3473
9.1.9.1_1.5	Test requirement p. 3473

9.1.9.2

TDD Relative RSRP Accuracy under Time-Domain Measurement Resource Restriction with Non-MBSFN ABS (eICIC) p. 3475

9.1.9.2.1	Test purpose p. 3475
9.1.9.2.2	Test applicability p. 3475
9.1.9.2.3	Minimum conformance requirements p. 3475
9.1.9.2.4	Test description p. 3476
9.1.9.2.5	Test requirement p. 3479

9.1.10

FDD RSRP Accuracy E-UTRA under Time-Domain Measurement Resource Restriction with MBSFN ABS (eICIC) p. 3480

9.1.10.1

FDD Absolute RSRP under Time-Domain Measurement Resource Restriction with MBSFN ABS (eICIC) p. 3480

9.1.10.1.1	Test purpose p. 3480
9.1.10.1.2	Test applicability p. 3480
9.1.10.1.3	Minimum conformance requirements p. 3481
9.1.10.1.4	Test description p. 3482
9.1.10.1.5	Test requirement p. 3484

9.1.10.1_1

FDD Absolute RSRP under Time-Domain Measurement Resource Restriction with MBSFN ABS (eICIC) (Rel-12 and forward) p. 3487

9.1.10.1_1.1	Test purpose p. 3487
9.1.10.1_1.2	Test applicability p. 3487
9.1.10.1_1.3	Minimum conformance requirements p. 3487
9.1.10.1_1.4	Test description p. 3488
9.1.10.1_1.5	Test requirement p. 3489

9.1.10.2

FDD Relative RSRP under Time-Domain Measurement Resource Restriction with MBSFN ABS (eICIC) p. 3492

9.1.10.2.1	Test purpose p. 3492
9.1.10.2.2	Test applicability p. 3492
9.1.10.2.3	Minimum conformance requirements p. 3492
9.1.10.2.4	Test description p. 3493
9.1.10.2.5	Test requirement p. 3496

9.1.11

TDD RSRP Accuracy E-UTRA under Time-Domain Measurement Resource Restriction with MBSFN ABS (eICIC) p. 3498

9.1.11.1

TDD Absolute RSRP under Time-Domain Measurement Resource Restriction with MBSFN ABS (eICIC) p. 3498

9.1.11.1.1	Test purpose p. 3498
9.1.11.1.2	Test applicability p. 3498
9.1.11.1.3	Minimum conformance requirements p. 3498
9.1.11.1.4	Test description p. 3500
9.1.11.1.5	Test requirement p. 3502

9.1.11.1_1

TDD Absolute RSRP under Time-Domain Measurement Resource Restriction with MBSFN ABS (eICIC) (Rel 12 and forward) p. 3504

9.1.11.1_1.1	Test purpose p. 3504
9.1.11.1_1.2	Test applicability p. 3504
9.1.11.1_1.3	Minimum conformance requirements p. 3505
9.1.11.1_1.4	Test description p. 3506
9.1.11.1_1.5	Test requirement p. 3506

9.1.11.2

TDD Relative RSRP under Time-Domain Measurement Resource Restriction with MBSFN ABS (eICIC) p. 3508

9.1.11.2.1	Test purpose p. 3508
9.1.11.2.2	Test applicability p. 3508
9.1.11.2.3	Minimum conformance requirements p. 3508
9.1.11.2.4	Test description p. 3509
9.1.11.2.5	Test requirement p. 3512

9.1.12

FDD RSRP Accuracy for E-UTRA Carrier Aggregation for 20 MHz p. 3514

9.1.12.1

FDD Absolute RSRP Accuracy for E-UTRA Carrier Aggregation for 20 MHz p. 3514

9.1.12.1.1	Test purpose p. 3514
9.1.12.1.2	Test applicability p. 3514
9.1.12.1.3	Minimum conformance requirements p. 3514
9.1.12.1.4	Test description p. 3515
9.1.12.1.5	Test requirement p. 3517

9.1.12.1_1

FDD Absolute RSRP Accuracy for E-UTRA Carrier Aggregation for 20 MHz (Rel-12 and forward) p. 3518

9.1.12.1_1.1	Test purpose p. 3518
9.1.12.1_1.2	Test applicability p. 3518
9.1.12.1_1.3	Minimum conformance requirements p. 3518
9.1.12.1_1.4	Test description p. 3519
9.1.12.1_1.5	Test requirement p. 3520

9.1.12.2

FDD Relative RSRP Accuracy for E-UTRA Carrier Aggregation for 20 MHz p. 3521

9.1.12.2.1	Test purpose p. 3521
9.1.12.2.2	Test applicability p. 3521
9.1.12.2.3	Minimum conformance requirements p. 3521
9.1.12.2.4	Test description p. 3522
9.1.12.2.5	Test requirement p. 3523

9.1.12.2_1

FDD Relative RSRP Accuracy for E-UTRA Carrier Aggregation for 20 MHz (Rel-12 and forward) p. 3524

9.1.12.2_1.1	Test purpose p. 3524
9.1.12.2_1.2	Test applicability p. 3524
9.1.12.2_1.3	Minimum conformance requirements p. 3524
9.1.12.2_1.4	Test description p. 3524
9.1.12.2_1.5	Test requirement p. 3525

9.1.13

TDD RSRP Accuracy for E-UTRA Carrier Aggregation for 20 MHz p. 3526

9.1.13.1

TDD Absolute RSRP Accuracy for E-UTRA Carrier Aggregation for 20 MHz p. 3526

9.1.13.1.1	Test purpose p. 3526
9.1.13.1.2	Test applicability p. 3526
9.1.13.1.3	Minimum conformance requirements p. 3526
9.1.13.1.4	Test description p. 3527
9.1.13.1.5	Test requirement p. 3529

9.1.13.1_1

TDD Absolute RSRP Accuracy for E-UTRA Carrier Aggregation for 20 MHz (Rel 12 and forward) p. 3529

9.1.13.1_1.1	Test purpose p. 3529
9.1.13.1_1.2	Test applicability p. 3530
9.1.13.1_1.3	Minimum conformance requirements p. 3530
9.1.13.1_1.4	Test description p. 3531
9.1.13.1_1.5	Test requirement p. 3531

9.1.13.2

TDD Relative RSRP Accuracy for E-UTRA Carrier Aggregation for 20 MHz p. 3532

9.1.13.2.1	Test purpose p. 3532
9.1.13.2.2	Test applicability p. 3532
9.1.13.2.3	Minimum conformance requirements p. 3532
9.1.13.2.4	Test description p. 3534
9.1.13.2.5	Test requirement p. 3535

9.1.13.2_1

TDD Relative RSRP Accuracy for E-UTRA Carrier Aggregation for 20 MHz (Rel-12 and forward) p. 3536

9.1.13.2_1.1	Test purpose p. 3536
9.1.13.2_1.2	Test applicability p. 3536
9.1.13.2_1.3	Minimum conformance requirements p. 3536
9.1.13.2_1.4	Test description p. 3536
9.1.13.2_1.5	Test requirement p. 3536

9.1.14

FDD RSRP under Time-Domain Measurement Resource Restriction with CRS Assistance Information and Non-MBSFN ABS (feICIC) p. 3537

9.1.14.1

FDD Intra Frequency Absolute RSRP Accuracy under Time-Domain Measurement Resource Restriction with CRS Assistance Information and Non-MBSFN ABS (feICIC) p. 3537

9.1.14.1.1	Test purpose p. 3537
9.1.14.1.2	Test applicability p. 3537
9.1.14.1.3	Minimum conformance requirements p. 3537
9.1.14.1.4	Test description p. 3538
9.1.14.1.5	Test requirement p. 3542

9.1.14.1_1

FDD Intra Frequency Absolute RSRP Accuracy under Time-Domain Measurement Resource Restriction with CRS Assistance Information and Non-MBSFN ABS (feICIC) (Rel 12 and forward) p. 3544

9.1.14.1_1.1	Test purpose p. 3544
9.1.14.1_1.2	Test applicability p. 3544
9.1.14.1_1.3	Minimum conformance requirements p. 3544
9.1.14.1_1.4	Test description p. 3545
9.1.14.1_1.5	Test requirement p. 3546

9.1.14.2

FDD Intra Frequency Relative RSRP Accuracy under Time-Domain Measurement Resource Restriction with CRS Assistance Information and Non-MBSFN ABS (feICIC) p. 3548

9.1.14.2.1	Test purpose p. 3548
9.1.14.2.2	Test applicability p. 3548
9.1.14.2.3	Minimum conformance requirements p. 3548
9.1.14.2.4	Test description p. 3549
9.1.14.2.5	Test requirement p. 3552

9.1.15

TDD RSRP under Time-Domain Measurement Resource Restriction with CRS Assistance Information and Non-MBSFN ABS (feICIC) p. 3554

9.1.15.1

TDD Intra Frequency Absolute RSRP Accuracy under Time-Domain Measurement Resource Restriction with CRS Assistance Information and Non-MBSFN ABS (feICIC) p. 3554

9.1.15.1.1	Test purpose p. 3554
9.1.15.1.2	Test applicability p. 3554
9.1.15.1.3	Minimum conformance requirements p. 3554
9.1.15.1.4	Test description p. 3555
9.1.15.1.5	Test requirement p. 3559

9.1.15.1_1

TDD Intra Frequency Absolute RSRP Accuracy under Time-Domain Measurement Resource Restriction with CRS Assistance Information and Non-MBSFN ABS (feICIC) (Rel 12 and forward) p. 3560

9.1.15.1_1.1	Test purpose p. 3560
9.1.15.1_1.2	Test applicability p. 3560
9.1.15.1_1.3	Minimum conformance requirements p. 3561
9.1.15.1_1.4	Test description p. 3562
9.1.15.1_1.5	Test requirement p. 3562

9.1.15.2

TDD Intra Frequency Relative RSRP Accuracy under Time-Domain Measurement Resource Restriction with CRS Assistance Information and Non-MBSFN ABS (feICIC) p. 3564

9.1.15.2.1	Test purpose p. 3564
9.1.15.2.2	Test applicability p. 3564
9.1.15.2.3	Minimum conformance requirements p. 3564
9.1.15.2.4	Test description p. 3565
9.1.15.2.5	Test requirement p. 3568

9.1.16

FDD Intra frequency RSRP Accuracy for 5MHz Bandwidth p. 3570

9.1.16.1

FDD Intra Frequency Absolute RSRP Accuracy for 5MHz Bandwidth p. 3570

9.1.16.1.1	Test purpose p. 3570
9.1.16.1.2	Test applicability p. 3570
9.1.16.1.3	Minimum conformance requirements p. 3570
9.1.16.1.4	Test description p. 3571
9.1.16.1.5	Test requirement p. 3571

9.1.16.1_1

FDD Intra Frequency Absolute RSRP Accuracy for 5MHz Bandwidth (Rel 12 and forward) p. 3572

9.1.16.1_1.1	Test purpose p. 3572
9.1.16.1_1.2	Test applicability p. 3572
9.1.16.1_1.3	Minimum conformance requirements p. 3572
9.1.16.1_1.4	Test description p. 3573
9.1.16.1_1.5	Test requirement p. 3574

9.1.16.2

FDD Intra Frequency Relative Accuracy of RSRP for 5MHz Bandwidth p. 3575

9.1.16.2.1	Test purpose p. 3575
9.1.16.2.2	Test applicability p. 3575
9.1.16.2.3	Minimum conformance requirements p. 3575
9.1.16.2.4	Test description p. 3576
9.1.16.2.5	Test requirement p. 3576

9.1.17

FDD Inter frequency RSRP Accuracy for 5MHz Bandwidth p. 3577

9.1.17.1

FDD - FDD Inter Frequency Absolute RSRP Accuracy for 5MHz Bandwidth p. 3577

9.1.17.1.1	Test purpose p. 3577
9.1.17.1.2	Test applicability p. 3577
9.1.17.1.3	Minimum conformance requirements p. 3577
9.1.17.1.4	Test description p. 3578
9.1.17.1.5	Test requirement p. 3578

9.1.17.1_1

FDD - FDD Inter Frequency Absolute RSRP Accuracy for 5MHz Bandwidth (Rel 12 and forward) p. 3580

9.1.17.1_1.1	Test purpose p. 3580
9.1.17.1_1.2	Test applicability p. 3580
9.1.17.1_1.3	Minimum conformance requirements p. 3580
9.1.17.1_1.4	Test description p. 3581
9.1.17.1_1.5	Test requirement p. 3581

9.1.17.2

FDD - FDD Inter Frequency Relative Accuracy of RSRP for 5MHz Bandwidth p. 3582

9.1.17.2.1	Test purpose p. 3582
9.1.17.2.2	Test applicability p. 3582
9.1.17.2.3	Minimum conformance requirements p. 3582
9.1.17.2.4	Test description p. 3583
9.1.17.2.5	Test requirement p. 3583

9.1.17.2_1

FDD - FDD Inter Frequency Relative Accuracy of RSRP for 5MHz Bandwidth (Rel 12 and forward) p. 3585

9.1.17.2_1.1	Test purpose p. 3585
9.1.17.2_1.2	Test applicability p. 3585
9.1.17.2_1.3	Minimum conformance requirements p. 3585
9.1.17.2_1.4	Test description p. 3586
9.1.17.2_1.5	Test requirement p. 3586

9.1.18

FDD RSRP Accuracy for E-UTRAN Carrier Aggregation for 10MHz + 5MHz p. 3587

9.1.18.1

FDD Absolute RSRP Accuracy for E-UTRA for Carrier Aggregation for 10MHz + 5MHz p. 3587

9.1.18.1.1	Test purpose p. 3587
9.1.18.1.2	Test applicability p. 3587
9.1.18.1.3	Minimum conformance requirements p. 3587
9.1.18.1.4	Test description p. 3587
9.1.18.1.5	Test requirement p. 3588

9.1.18.1_1

FDD Absolute RSRP Accuracy for E-UTRA for Carrier Aggregation for 10MHz + 5MHz (Rel 12 and forward) p. 3589

9.1.18.1_1.1	Test purpose p. 3589
9.1.18.1_1.2	Test applicability p. 3589
9.1.18.1_1.3	Minimum conformance requirements p. 3589
9.1.18.1_1.4	Test description p. 3589
9.1.18.1_1.5	Test requirement p. 3590

9.1.18.2

FDD Relative RSRP Accuracy E-UTRA for Carrier Aggregation for 10MHz + 5MHz p. 3591

9.1.18.2.1	Test purpose p. 3591
9.1.18.2.2	Test applicability p. 3591
9.1.18.2.3	Minimum conformance requirements p. 3591
9.1.18.2.4	Test description p. 3591
9.1.18.2.5	Test requirement p. 3592

9.1.18.2_1

FDD Relative RSRP Accuracy E-UTRA for Carrier Aggregation for 10MHz + 5MHz (Rel-12 and forward) p. 3593

9.1.18.2_1.1	Test purpose p. 3593
9.1.18.2_1.2	Test applicability p. 3593
9.1.18.2_1.3	Minimum conformance requirements p. 3593
9.1.18.2_1.4	Test description p. 3593
9.1.18.2_1.5	Test requirement p. 3593

9.1.19

TDD RSRP Accuracy for E-UTRAN Carrier Aggregation for 10MHz + 5MHz p. 3595

9.1.19.1

TDD Absolute RSRP Accuracy for E-UTRA Carrier Aggregation for 10MHz + 5MHz p. 3595

9.1.19.1.1	Test purpose p. 3595
9.1.19.1.2	Test applicability p. 3595
9.1.19.1.3	Minimum conformance requirements p. 3595
9.1.19.1.4	Test description p. 3595
9.1.19.1.5	Test requirement p. 3596

9.1.19.1_1

TDD Absolute RSRP Accuracy for E-UTRA Carrier Aggregation for 10MHz + 5MHz (Rel 12 and forward) p. 3597

9.1.19.1_1.1	Test purpose p. 3597
9.1.19.1_1.2	Test applicability p. 3597
9.1.19.1_1.3	Minimum conformance requirements p. 3597
9.1.19.1_1.4	Test description p. 3597
9.1.19.1_1.5	Test requirement p. 3597

9.1.19.2

TDD Relative RSRP Accuracy for E-UTRA Carrier Aggregation for 10MHz + 5MHz p. 3598

9.1.19.2.1	Test purpose p. 3598
9.1.19.2.2	Test applicability p. 3598
9.1.19.2.3	Minimum conformance requirements p. 3599
9.1.19.2.4	Test description p. 3599
9.1.19.2.5	Test requirement p. 3599

9.1.19.2_1

TDD Relative RSRP Accuracy for E-UTRA Carrier Aggregation for 10MHz + 5MHz (Rel-12 and forward) p. 3600

9.1.19.2_1.1	Test purpose p. 3600
9.1.19.2_1.2	Test applicability p. 3600
9.1.19.2_1.3	Minimum conformance requirements p. 3600
9.1.19.2_1.4	Test description p. 3601
9.1.19.2_1.5	Test requirement p. 3601

9.1.20

FDD RSRP Accuracy for E-UTRA Carrier Aggregation for 5MHz + 5MHz bandwidth p. 3602

9.1.20.1

FDD Absolute RSRP Accuracy for E-UTRA Carrier Aggregation for 5MHz + 5MHz bandwidth p. 3602

9.1.20.1.1	Test purpose p. 3602
9.1.20.1.2	Test applicability p. 3602
9.1.20.1.3	Minimum conformance requirements p. 3602
9.1.20.1.4	Test description p. 3602
9.1.20.1.5	Test requirement p. 3603

9.1.20.1_1

FDD Absolute RSRP Accuracy for E-UTRA Carrier Aggregation for 5MHz + 5MHz bandwidth (Rel 12 and forward) p. 3604

9.1.20.1_1.1	Test purpose p. 3604
9.1.20.1_1.2	Test applicability p. 3604
9.1.20.1_1.3	Minimum conformance requirements p. 3604
9.1.20.1_1.4	Test description p. 3604
9.1.20.1_1.5	Test requirement p. 3605

9.1.20.2

FDD Relative RSRP Accuracy for E-UTRA Carrier Aggregation for 5MHz + 5MHz bandwidth p. 3606

9.1.20.2.1	Test purpose p. 3606
9.1.20.2.2	Test applicability p. 3606
9.1.20.2.3	Minimum conformance requirements p. 3606
9.1.20.2.4	Test description p. 3606
9.1.20.2.5	Test requirement p. 3607

9.1.20.2_1

FDD Relative RSRP Accuracy for E-UTRA Carrier Aggregation for 5MHz + 5MHz bandwidth (Rel-12 and forward) p. 3608

9.1.20.2_1.1	Test purpose p. 3608
9.1.20.2_1.2	Test applicability p. 3608
9.1.20.2_1.3	Minimum conformance requirements p. 3608
9.1.20.2_1.4	Test description p. 3608
9.1.20.2_1.5	Test requirement p. 3609

9.1.21

TDD RSRP Accuracy for E-UTRAN Carrier Aggregation for 5MHz + 5MHz p. 3610

9.1.21.1

TDD Absolute RSRP Accuracy for E-UTRA Carrier Aggregation for 5MHz + 5MHz p. 3610

9.1.21.1.1	Test purpose p. 3610
9.1.21.1.2	Test applicability p. 3610
9.1.21.1.3	Minimum conformance requirements p. 3610
9.1.21.1.4	Test description p. 3610
9.1.21.1.5	Test requirement p. 3611

9.1.21.1_1

TDD Absolute RSRP Accuracy for E-UTRA Carrier Aggregation for 5MHz + 5MHz (Rel 12 and forward) p. 3612

9.1.21.1_1.1	Test purpose p. 3612
9.1.21.1_1.2	Test applicability p. 3612
9.1.21.1_1.3	Minimum conformance requirements p. 3612
9.1.21.1_1.4	Test description p. 3612
9.1.21.1_1.5	Test requirement p. 3612

9.1.21.2

TDD Relative RSRP Accuracy for E-UTRA Carrier Aggregation for 5MHz + 5MHz p. 3613

9.1.21.2.1	Test purpose p. 3613
9.1.21.2.2	Test applicability p. 3613
9.1.21.2.3	Minimum conformance requirements p. 3613
9.1.21.2.4	Test description p. 3614
9.1.21.2.5	Test requirement p. 3614

9.1.21.2_1

TDD Relative RSRP Accuracy for E-UTRA Carrier Aggregation for 5MHz + 5MHz (Rel-12 and forward) p. 3615

9.1.21.2_1.1	Test purpose p. 3615
9.1.21.2_1.2	Test applicability p. 3615
9.1.21.2_1.3	Minimum conformance requirements p. 3615
9.1.21.2_1.4	Test description p. 3616
9.1.21.2_1.5	Test requirement p. 3616

9.1.22

FDD-TDD RSRP Accuracy E-UTRA for Carrier Aggregation with PCell in FDD p. 3617

9.1.22.1

Test purpose p. 3617

9.1.22.2

Test applicability p. 3617

9.1.22.3

Minimum conformance requirements p. 3617

9.1.22.4

Test description p. 3620

9.1.22.4.1	Initial conditions p. 3620
9.1.22.4.2	Test procedure p. 3620
9.1.22.4.3	Message contents p. 3621

9.1.22.5

Test requirement p. 3621

9.1.23

FDD-TDD RSRP Accuracy E-UTRA for Carrier Aggregation with PCell in TDD p. 3624

9.1.23.1

Test purpose p. 3624

9.1.23.2

Test applicability p. 3624

9.1.23.3

Minimum conformance requirements p. 3624

9.1.23.4

Test description p. 3626

9.1.23.4.1	Initial conditions p. 3626
9.1.23.4.2	Test procedure p. 3626
9.1.23.4.3	Message contents p. 3627

9.1.23.5

Test requirement p. 3627

9.1.24

TDD RSRP Accuracy for E-UTRAN Carrier Aggregation for 20MHz + 10MHz p. 3630

9.1.24.1

TDD Absolute RSRP Accuracy for E-UTRA Carrier Aggregation for 20MHz + 10MHz p. 3630

9.1.24.1.1	Test purpose p. 3630
9.1.24.1.2	Test applicability p. 3630
9.1.24.1.3	Minimum conformance requirements p. 3630
9.1.24.1.4	Test description p. 3630
9.1.24.1.5	Test requirement p. 3631

9.1.24.1_1

TDD Absolute RSRP Accuracy for E-UTRA Carrier Aggregation for 20MHz + 10MHz (Rel 12 and forward) p. 3632

9.1.24.1_1.1	Test purpose p. 3632
9.1.24.1_1.2	Test applicability p. 3632
9.1.24.1_1.3	Minimum conformance requirements p. 3632
9.1.24.1_1.4	Test description p. 3632
9.1.24.1_1.5	Test requirement p. 3633

9.1.24.2

TDD Relative RSRP Accuracy for E-UTRA Carrier Aggregation for 20MHz + 10MHz p. 3634

9.1.24.2.1	Test purpose p. 3634
9.1.24.2.2	Test applicability p. 3634
9.1.24.2.3	Minimum conformance requirements p. 3634
9.1.24.2.4	Test description p. 3635
9.1.24.2.5	Test requirement p. 3635

9.1.24.2_1

TDD Relative RSRP Accuracy for E-UTRA Carrier Aggregation for 20MHz + 10MHz (Rel-12 and forward) p. 3636

9.1.24.2_1.1	Test purpose p. 3636
9.1.24.2_1.2	Test applicability p. 3636
9.1.24.2_1.3	Minimum conformance requirements p. 3637
9.1.24.2_1.4	Test description p. 3637
9.1.24.2_1.5	Test requirement p. 3637

9.1.25

FDD intra-frequency absolute and relative RSRP accuracies in CRS based discovery signal p. 3638

9.1.25.1

Test purpose p. 3638

9.1.25.2

Test applicability p. 3638

9.1.25.3

Minimum conformance requirements p. 3638

9.1.25.4

Test description p. 3640

9.1.25.4.1	Initial conditions p. 3640
9.1.25.4.2	Test procedure p. 3640
9.1.25.4.3	Message contents p. 3641

9.1.25.5

Test requirement p. 3642

9.1.26

TDD intra-frequency absolute and relative RSRP accuracies in CRS based discovery signal p. 3643

9.1.26.1

Test purpose p. 3643

9.1.26.2

Test applicability p. 3643

9.1.26.3

Minimum conformance requirements p. 3643

9.1.26.4

Test description p. 3644

9.1.26.4.1	Initial conditions p. 3644
9.1.26.4.2	Test procedure p. 3644
9.1.26.4.3	Message contents p. 3644

9.1.26.5

Test requirement p. 3645

9.1.27

FDD-FDD inter-frequency absolute and relative RSRP accuracies in CRS based discovery signal p. 3646

9.1.27.1

Test purpose p. 3646

9.1.27.2

Test applicability p. 3646

9.1.27.3

Minimum conformance requirements p. 3647

9.1.27.4

Test description p. 3648

9.1.27.4.1	Initial conditions p. 3648
9.1.27.4.2	Test procedure p. 3649
9.1.27.4.3	Message contents p. 3649

9.1.27.5

Test requirement p. 3650

9.1.28

TDD-TDD inter-frequency absolute and relative RSRP accuracies in CRS based discovery signal p. 3652

9.1.28.1

Test purpose p. 3652

9.1.28.2

Test applicability p. 3652

9.1.28.3

Minimum conformance requirements p. 3653

9.1.28.4

Test description p. 3653

9.1.28.4.1	Initial conditions p. 3653
9.1.28.4.2	Test procedure p. 3653
9.1.28.4.3	Message contents p. 3653

9.1.28.5

Test requirement p. 3654

9.1.29

FDD intra frequency absolute and relative CSI-RSRP accuracies in CSI-RS based discovery signal p. 3656

9.1.29.1

Test purpose p. 3656

9.1.29.2

Test applicability p. 3656

9.1.29.3

Minimum conformance requirements p. 3656

9.1.29.4

Test description p. 3658

9.1.29.4.1	Initial conditions p. 3658
9.1.29.4.2	Test procedure p. 3658
9.1.29.4.3	Message contents p. 3659

9.1.29.5

Test requirement p. 3660

9.1.30

TDD intra-frequency absolute and relative CSI-RSRP accuracies in CSI-RS based discovery signal p. 3662

9.1.30.1

Test purpose p. 3662

9.1.30.2

Test applicability p. 3662

9.1.30.3

Minimum conformance requirements p. 3662

9.1.30.4

Test description p. 3662

9.1.30.4.1	Initial conditions p. 3662
9.1.30.4.2	Test procedure p. 3663
9.1.30.4.3	Message contents p. 3663

9.1.30.5

Test requirement p. 3664

9.1.31

FDD-FDD inter-frequency absolute and relative CSI-RSRP accuracies in CSI-RS based discovery signal p. 3666

9.1.31.1

Test purpose p. 3666

9.1.31.2

Test applicability p. 3666

9.1.31.3

Minimum conformance requirements p. 3666

9.1.31.4

Test description p. 3668

9.1.31.4.1	Initial conditions p. 3668
9.1.31.4.2	Test procedure p. 3668
9.1.31.4.3	Message contents p. 3669

9.1.31.5

Test requirement p. 3670

9.1.32

TDD-TDD inter-frequency absolute and relative CSI-RSRP accuracies in CSI-RS based discovery signal p. 3672

9.1.32.1

Test purpose p. 3672

9.1.32.2

Test applicability p. 3672

9.1.32.3

Minimum conformance requirements p. 3672

9.1.32.4

Test description p. 3672

9.1.32.4.1	Initial conditions p. 3672
9.1.32.4.2	Test procedure p. 3673
9.1.32.4.3	Message contents p. 3673

9.1.32.5

Test requirement p. 3674

9.1.33

FDD absolute and relative RSRP accuracies for E-UTRAN Carrier Aggregation in CRS based discovery signal p. 3676

9.1.33.1

Test purpose p. 3676

9.1.33.2

Test applicability p. 3676

9.1.33.3

Minimum conformance requirements p. 3676

9.1.33.4

Test description p. 3678

9.1.33.4.1	Initial conditions p. 3678
9.1.33.4.2	Test procedure p. 3679
9.1.33.4.3	Message contents p. 3679

9.1.33.5

Test requirement p. 3680

9.1.34

TDD absolute and relative RSRP accuracies for E-UTRAN Carrier Aggregation in CRS based discovery signal p. 3682

9.1.34.1

Test purpose p. 3682

9.1.34.2

Test applicability p. 3683

9.1.34.3

Minimum conformance requirements p. 3683

9.1.34.4

Test description p. 3683

9.1.34.4.1	Initial conditions p. 3683
9.1.34.4.2	Test procedure p. 3683
9.1.34.4.3	Message contents p. 3683

9.1.34.5

Test requirement p. 3684

9.1.35

FDD absolute and relative CSI-RSRP accuracies for E-UTRAN Carrier Aggregation in CSI-RS based discovery signal p. 3686

9.1.35.1

Test purpose p. 3686

9.1.35.2

Test applicability p. 3686

9.1.35.3

Minimum conformance requirements p. 3686

9.1.35.4

Test description p. 3688

9.1.35.4.1	Initial conditions p. 3688
9.1.35.4.2	Test procedure p. 3689
9.1.35.4.3	Message contents p. 3689

9.1.35.5

Test requirement p. 3691

9.1.36

TDD absolute and relative CSI-RSRP accuracies for E-UTRAN Carrier Aggregation in CSI-RS based discovery signal p. 3694

9.1.36.1

Test purpose p. 3694

9.1.36.2

Test applicability p. 3694

9.1.36.3

Minimum conformance requirements p. 3694

9.1.36.4

Test description p. 3694

9.1.36.4.1	Initial conditions p. 3694
9.1.36.4.2	Test procedure p. 3695
9.1.36.4.3	Message contents p. 3695

9.1.36.5

Test requirement p. 3697

9.1.37_40_1

Void p. …

9.1.41

FD-FDD Intra frequency RSRP Accuracy for UE category 0 p. 3699

9.1.41.1

FD-FDD Intra Frequency Absolute RSRP Accuracy for UE category 0 p. 3699

9.1.41.1.1	Test purpose p. 3699
9.1.41.1.2	Test applicability p. 3699
9.1.41.1.3	Minimum conformance requirements p. 3699
9.1.41.1.4	Test description p. 3700
9.1.41.1.5	Test requirement p. 3702

9.1.41.2

FD-FDD Intra Frequency Relative RSRP Accuracy for UE category 0 p. 3704

9.1.41.2.1	Test purpose p. 3704
9.1.41.2.2	Test applicability p. 3704
9.1.41.2.3	Minimum conformance requirements p. 3704
9.1.41.2.4	Test description p. 3705
9.1.41.2.5	Test requirement p. 3706

9.1.42

HD-FDD Intra frequency RSRP Accuracy for UE category 0 p. 3709

9.1.42.1

HD-FDD Intra Frequency Absolute RSRP Accuracy for UE category 0 p. 3709

9.1.42.1.1	Test purpose p. 3709
9.1.42.1.2	Test applicability p. 3709
9.1.42.1.3	Minimum conformance requirements p. 3709
9.1.42.1.4	Test description p. 3710
9.1.42.1.5	Test requirement p. 3711

9.1.42.2

HD-FDD Intra Frequency Relative RSRP Accuracy for UE category 0 p. 3713

9.1.42.2.1	Test purpose p. 3713
9.1.42.2.2	Test applicability p. 3714
9.1.42.2.3	Minimum conformance requirements p. 3714
9.1.42.2.4	Test description p. 3715
9.1.42.2.5	Test requirement p. 3716

9.1.43

TDD Intra frequency RSRP Accuracy for UE category 0 p. 3718

9.1.43.1

TDD Intra Frequency Absolute RSRP Accuracy for UE category 0 p. 3718

9.1.43.1.1	Test purpose p. 3718
9.1.43.1.2	Test applicability p. 3718
9.1.43.1.3	Minimum conformance requirements p. 3719
9.1.43.1.4	Test description p. 3720
9.1.43.1.5	Test requirement p. 3721

9.1.43.2

TDD Intra Frequency Relative RSRP Accuracy for UE category 0 p. 3723

9.1.43.2.1	Test purpose p. 3723
9.1.43.2.2	Test applicability p. 3723
9.1.43.2.3	Minimum conformance requirements p. 3723
9.1.43.2.4	Test description p. 3724
9.1.43.2.5	Test requirement p. 3725

9.1.44_51

Void p. …

9.1.52

FD-FDD RSRP Intra frequency case for BL/CE UE in CEModeA p. 3727

9.1.52.1

Test purpose p. 3727

9.1.52.2

Test applicability p. 3727

9.1.52.3

Minimum conformance requirements p. 3727

9.1.52.4

Test description p. 3729

9.1.52.4.1	Initial conditions p. 3729
9.1.52.4.2	Test procedure p. 3729
9.1.52.4.3	Message contents p. 3730

9.1.52.5

Test requirement p. 3731

9.1.53

HD-FDD RSRP Intra frequency case for BL/CE UE in CEModeA p. 3733

9.1.53.1	Test purpose p. 3733
9.1.53.2	Test applicability p. 3733
9.1.53.3	Minimum conformance requirements p. 3733
9.1.53.4	Test description p. 3733
9.1.53.5	Test requirement p. 3733

9.1.54

TDD RSRP Intra frequency case for BL/CE UE in CEModeA p. 3736

9.1.54.1	Test purpose p. 3736
9.1.54.2	Test applicability p. 3736
9.1.54.3	Minimum conformance requirements p. 3736
9.1.54.4	Test description p. 3736
9.1.54.5	Test requirement p. 3736

9.1.55

FS3 Intra frequency absolute and relative RSRP accuracies with FDD PCell p. 3738

9.1.55.1

Test purpose p. 3738

9.1.55.2

Test applicability p. 3738

9.1.55.3

Minimum conformance requirements p. 3738

9.1.55.4

Test description p. 3740

9.1.55.4.1	Initial conditions p. 3740
9.1.55.4.2	Test procedure p. 3740
9.1.55.4.3	Message contents p. 3741

9.1.55.5

Test requirement p. 3741

9.1.56

FS3 Intra frequency absolute and relative RSRP accuracies with TDD PCell p. 3744

9.1.56.1

Test purpose p. 3744

9.1.56.2

Test applicability p. 3744

9.1.56.3

Minimum conformance requirements p. 3744

9.1.56.4

Test description p. 3746

9.1.56.4.1	Initial conditions p. 3746
9.1.56.4.2	Test procedure p. 3747
9.1.56.4.3	Message contents p. 3747

9.1.56.5

Test requirement p. 3747

9.1.57

FD-FDD RSRP Intra frequency case for BL/CE UE in CEModeB p. 3750

9.1.57.1

Test purpose p. 3750

9.1.57.2

Test applicability p. 3750

9.1.57.3

Minimum conformance requirements p. 3750

9.1.57.4

Test description p. 3752

9.1.57.4.1	Initial conditions p. 3752
9.1.57.4.2	Test procedure p. 3753
9.1.57.4.3	Message contents p. 3753

9.1.57.5

Test requirement p. 3754

9.1.58

HD-FDD RSRP Intra frequency case for BL/CE UE in CEModeB p. 3757

9.1.58.1	Test purpose p. 3757
9.1.58.2	Test applicability p. 3757
9.1.58.3	Minimum conformance requirements p. 3757
9.1.58.4	Test description p. 3758
9.1.58.5	Test requirement p. 3758

9.1.59

TDD RSRP Intra frequency case for BL/CE UE in CEModeB p. 3760

9.1.59.1

Test purpose p. 3760

9.1.59.2

Test applicability p. 3761

9.1.59.3

Minimum conformance requirements p. 3761

9.1.59.4

Test description p. 3761

9.1.59.4.1	Initial conditions p. 3761
9.1.59.4.2	Test procedure p. 3761
9.1.59.4.3	Message contents p. 3761

9.1.59.5

Test requirement p. 3761

9.1.60

FS3 Absolute and relative CSI-RSRP accuracies in CSI-RS based discovery signal with FDD PCell p. 3763

9.1.60.1

Test purpose p. 3763

9.1.60.2

Test applicability p. 3763

9.1.60.3

Minimum conformance requirements p. 3763

9.1.60.4

Test description p. 3764

9.1.60.4.1	Initial conditions p. 3764
9.1.60.4.2	Test procedure p. 3765
9.1.60.4.3	Message contents p. 3765

9.1.60.5

Test requirement p. 3767

9.1.61

FS3 Absolute and relative CSI-RSRP accuracies in CSI-RS based discovery signal with TDD PCell p. 3770

9.1.61.1

Test purpose p. 3770

9.1.61.2

Test applicability p. 3770

9.1.61.3

Minimum conformance requirements p. 3770

9.1.61.4

Test description p. 3772

9.1.61.4.1	Initial conditions p. 3772
9.1.61.4.2	Test procedure p. 3772
9.1.61.4.3	Message contents p. 3773

9.1.61.5

Test requirement p. 3773

9.1.62_67

- p. 3775

9.1.68

3DL RSRP for E-UTRAN in Carrier Aggregation with generic duplex modes p. 3776

9.1.68.1

Test purpose p. 3776

9.1.68.2

Test applicability p. 3776

9.1.68.3

Minimum conformance requirements p. 3776

9.1.68.4

Test description p. 3778

9.1.68.4.1	Initial conditions p. 3778
9.1.68.4.2	Test procedure p. 3779
9.1.68.4.3	Message contents p. 3780

9.1.68.5

Test requirement p. 3780

9.1.69

4 DL RSRP for E-UTRAN in Carrier Aggregation with generic duplex modes p. 3785

9.1.69.1

Test purpose p. 3785

9.1.69.2

Test applicability p. 3785

9.1.69.3

Minimum conformance requirements p. 3785

9.1.69.4

Test description p. 3787

9.1.69.4.1	Initial conditions p. 3787
9.1.69.4.2	Test procedure p. 3788
9.1.69.4.3	Message contents p. 3789

9.1.69.5

Test requirement p. 3789

9.1.70

5 DL RSRP for E-UTRAN in Carrier Aggregation with generic duplex modes p. 3796

9.1.70.1

Test purpose p. 3796

9.1.70.2

Test applicability p. 3796

9.1.70.3

Minimum conformance requirements p. 3796

9.1.70.4

Test description p. 3799

9.1.70.4.1	Initial conditions p. 3799
9.1.70.4.2	Test procedure p. 3799
9.1.70.4.3	Message contents p. 3800

9.1.70.5

Test requirement p. 3801

9.1.71

6 DL RSRP for E-UTRAN in Carrier Aggregation with generic duplex modes p. 3810

9.1.71.1

Test purpose p. 3810

9.1.71.2

Test applicability p. 3810

9.1.71.3

Minimum conformance requirements p. 3810

9.1.71.4

Test description p. 3813

9.1.71.4.1	Initial conditions p. 3813
9.1.71.4.2	Test procedure p. 3813
9.1.71.4.3	Message contents p. 3815

9.1.71.5

Test requirement p. 3815

9.1.72

7 DL RSRP for E-UTRAN in Carrier Aggregation with generic duplex modes p. 3826

9.1.72.1

Test purpose p. 3826

9.1.72.2

Test applicability p. 3826

9.1.72.3

Minimum conformance requirements p. 3826

9.1.72.4

Test description p. 3828

9.1.72.4.1	Initial conditions p. 3828
9.1.72.4.2	Test procedure p. 3829
9.1.72.4.3	Message contents p. 3830

9.1.72.5

Test requirement p. 3830

9.2

- p. 3844

9.2.1

FDD Intra frequency RSRQ Accuracy p. 3844

9.2.1.1

FDD Intra Frequency Absolute RSRQ Accuracy p. 3844

9.2.1.1.1	Test purpose p. 3844
9.2.1.1.2	Test applicability p. 3844
9.2.1.1.3	Minimum conformance requirements p. 3844
9.2.1.1.4	Test description p. 3845
9.2.1.1.5	Test requirement p. 3846

9.2.1.1_2

FDD Intra Frequency Absolute RSRQ Accuracy for UE category 1bis p. 3848

9.2.1.1_2.1	Test purpose p. 3848
9.2.1.1_2.2	Test applicability p. 3848
9.2.1.1_2.3	Minimum conformance requirements p. 3848
9.2.1.1_2.4	Test description p. 3849
9.2.1.1_2.5	Test requirement p. 3850

9.2.1.1_3

FDD Intra Frequency Absolute RSRQ Accuracy for CA Idle Mode Measurements p. 3851

9.2.1.1_3.1	Test purpose p. 3851
9.2.1.1_3.2	Test applicability p. 3851
9.2.1.1_3.3	Minimum conformance requirements p. 3852
9.2.1.1_3.4	Test description p. 3852
9.2.1.1_3.5	Test requirement p. 3857

9.2.2

TDD Intra frequency RSRQ Accuracy p. 3859

9.2.2.1

TDD Intra Frequency Absolute RSRQ Accuracy p. 3859

9.2.2.1.1	Test purpose p. 3859
9.2.2.1.2	Test applicability p. 3859
9.2.2.1.3	Minimum conformance requirements p. 3859
9.2.2.1.4	Test description p. 3860
9.2.2.1.5	Test requirement p. 3861

9.2.2.1_2

TDD Intra Frequency Absolute RSRQ Accuracy for UE category 1bis p. 3863

9.2.2.1_2.1	Test purpose p. 3863
9.2.2.1_2.2	Test applicability p. 3863
9.2.2.1_2.3	Minimum conformance requirements p. 3863
9.2.2.1_2.4	Test description p. 3863
9.2.2.1_2.5	Test requirement p. 3864

9.2.3

FDD - FDD Inter frequency RSRQ Accuracy p. 3865

9.2.3.1

FDD - FDD Inter Frequency Absolute RSRQ Accuracy p. 3865

9.2.3.1.1	Test purpose p. 3865
9.2.3.1.2	Test applicability p. 3865
9.2.3.1.3	Minimum conformance requirements p. 3865
9.2.3.1.4	Test description p. 3866
9.2.3.1.5	Test requirement p. 3868

9.2.3.1_2

FDD - FDD Inter Frequency Absolute RSRQ Accuracy for UE category 1bis p. 3870

9.2.3.1_2.1	Test purpose p. 3870
9.2.3.1_2.2	Test applicability p. 3870
9.2.3.1_2.3	Minimum conformance requirements p. 3870
9.2.3.1_2.4	Test description p. 3871
9.2.3.1_2.5	Test requirement p. 3871

9.2.3.1_3

FDD - FDD Inter Frequency Absolute RSRQ Accuracy for CA Idle Mode Measurements for Overlapping Carrier p. 3873

9.2.3.1_3.1	Test purpose p. 3873
9.2.3.1_3.2	Test applicability p. 3873
9.2.3.1_3.3	Minimum conformance requirements p. 3873
9.2.3.1_3.4	Test description p. 3874
9.2.3.1_3.5	Test requirement p. 3878

9.2.3.1_4

FDD - FDD Inter Frequency Absolute RSRQ Accuracy for CA Idle Mode Measurements for Non-overlapping Carriers p. 3880

9.2.3.1_4.1	Test purpose p. 3880
9.2.3.1_4.2	Test applicability p. 3880
9.2.3.1_4.3	Minimum conformance requirements p. 3880
9.2.3.1_4.4	Test description p. 3881
9.2.3.1_4.5	Test requirement p. 3885

9.2.3.2

FDD - FDD Inter Frequency Relative Accuracy of RSRQ p. 3887

9.2.3.2.1	Test purpose p. 3887
9.2.3.2.2	Test applicability p. 3887
9.2.3.2.3	Minimum conformance requirements p. 3887
9.2.3.2.4	Test description p. 3888
9.2.3.2.5	Test requirement p. 3889

9.2.3.2_2

FDD - FDD Inter Frequency Relative Accuracy of RSRQ for UE category 1bis p. 3891

9.2.3.2_2.1	Test purpose p. 3891
9.2.3.2_2.2	Test applicability p. 3891
9.2.3.2_2.3	Minimum conformance requirements p. 3891
9.2.3.2_2.4	Test description p. 3892
9.2.3.2_2.5	Test requirement p. 3893

9.2.4

TDD - TDD Inter frequency RSRQ Accuracy p. 3894

9.2.4.1

TDD - TDD Inter Frequency Absolute RSRQ Accuracy p. 3894

9.2.4.1.1	Test purpose p. 3894
9.2.4.1.2	Test applicability p. 3895
9.2.4.1.3	Minimum conformance requirements p. 3895
9.2.4.1.4	Test description p. 3895
9.2.4.1.5	Test requirement p. 3897

9.2.4.1_1

TDD - TDD Inter Frequency Absolute RSRQ Accuracy (Rel 12 and forward) p. 3898

9.2.4.1_1.1	Test purpose p. 3898
9.2.4.1_1.2	Test applicability p. 3898
9.2.4.1_1.3	Minimum conformance requirements p. 3898
9.2.4.1_1.4	Test description p. 3898
9.2.4.1_1.5	Test requirement p. 3899

9.2.4.1_2

TDD - TDD Inter Frequency Absolute RSRQ Accuracy for UE category 1bis p. 3901

9.2.4.1_2.1	Test purpose p. 3901
9.2.4.1_2.2	Test applicability p. 3902
9.2.4.1_2.3	Minimum conformance requirements p. 3902
9.2.4.1_2.4	Test description p. 3902
9.2.4.1_2.5	Test requirement p. 3903

9.2.4.2

TDD - TDD Inter Frequency Relative Accuracy of RSRQ p. 3904

9.2.4.2.1	Test purpose p. 3904
9.2.4.2.2	Test applicability p. 3904
9.2.4.2.3	Minimum conformance requirements p. 3904
9.2.4.2.4	Test description p. 3905
9.2.4.2.5	Test requirement p. 3906

9.2.4.2_1

TDD - TDD Inter Frequency Relative Accuracy of RSRQ (Rel 12 and forward) p. 3908

9.2.4.2_1.1	Test purpose p. 3908
9.2.4.2_1.2	Test applicability p. 3908
9.2.4.2_1.3	Minimum conformance requirements p. 3908
9.2.4.2_1.4	Test description p. 3908
9.2.4.2_1.5	Test requirement p. 3909

9.2.4.2_2

TDD - TDD Inter Frequency Relative Accuracy of RSRQ for UE category 1bis p. 3911

9.2.4.2_2.1	Test purpose p. 3911
9.2.4.2_2.2	Test applicability p. 3911
9.2.4.2_2.3	Minimum conformance requirements p. 3911
9.2.4.2_2.4	Test description p. 3912
9.2.4.2_2.5	Test requirement p. 3914

9.2.4A

FDD - TDD Inter frequency RSRQ Accuracy p. 3915

9.2.4A.1

FDD - TDD Inter Frequency Absolute RSRQ Accuracy p. 3915

9.2.4A.1.1	Test purpose p. 3915
9.2.4A.1.2	Test applicability p. 3915
9.2.4A.1.3	Minimum conformance requirements p. 3915
9.2.4A.1.4	Test description p. 3916
9.2.4A.1.5	Test requirement p. 3918

9.2.4A.1_2

FDD - TDD Inter Frequency Absolute RSRQ Accuracy for UE category 1bis p. 3920

9.2.4A.1_2.1	Test purpose p. 3920
9.2.4A.1_2.2	Test applicability p. 3920
9.2.4A.1_2.3	Minimum conformance requirements p. 3920
9.2.4A.1_2.4	Test description p. 3921
9.2.4A.1_2.5	Test requirement p. 3922

9.2.4A.2

FDD - TDD Inter Frequency Relative Accuracy of RSRQ p. 3925

9.2.4A.2.1	Test purpose p. 3925
9.2.4A.2.2	Test applicability p. 3925
9.2.4A.2.3	Minimum conformance requirements p. 3925
9.2.4A.2.4	Test description p. 3926
9.2.4A.2.5	Test requirement p. 3927

9.2.4A.2_2

FDD - TDD Inter Frequency Relative Accuracy of RSRQ for UE category 1bis p. 3929

9.2.4A.2_2.1	Test purpose p. 3929
9.2.4A.2_2.2	Test applicability p. 3929
9.2.4A.2_2.3	Minimum conformance requirements p. 3930
9.2.4A.2_2.4	Test description p. 3931
9.2.4A.2_2.5	Test requirement p. 3932

9.2.5

FDD RSRQ for E-UTRA Carrier Aggregation p. 3934

9.2.5.1

FDD Absolute RSRQ Accuracy for E-UTRA Carrier Aggregation p. 3934

9.2.5.1.1	Test purpose p. 3934
9.2.5.1.2	Test applicability p. 3934
9.2.5.1.3	Minimum conformance requirements p. 3935
9.2.5.1.4	Test description p. 3935
9.2.5.1.5	Test requirement p. 3937

9.2.5.2

FDD Relative RSRQ Accuracy E-UTRA for Carrier Aggregation p. 3939

9.2.5.2.1	Test purpose p. 3939
9.2.5.2.2	Test applicability p. 3939
9.2.5.2.3	Minimum conformance requirements p. 3939
9.2.5.2.4	Test description p. 3940
9.2.5.2.5	Test requirement p. 3941

9.2.6

TDD RSRQ for E-UTRA Carrier Aggregation p. 3943

9.2.6.1

TDD Absolute RSRQ Accuracy for E-UTRA Carrier Aggregation p. 3943

9.2.6.1.1	Test purpose p. 3943
9.2.6.1.2	Test applicability p. 3943
9.2.6.1.3	Minimum conformance requirements p. 3943
9.2.6.1.4	Test description p. 3944
9.2.6.1.5	Test requirement p. 3945

9.2.6.2

TDD Relative RSRQ Accuracy for E-UTRA Carrier Aggregation p. 3947

9.2.6.2.1	Test purpose p. 3947
9.2.6.2.2	Test applicability p. 3947
9.2.6.2.3	Minimum conformance requirements p. 3947
9.2.6.2.4	Test description p. 3948
9.2.6.2.5	Test requirement p. 3949

9.2.7

FDD RSRQ Accuracy under Time Domain Measurement Resource Restriction with Non-MBSFN ABS p. 3951

9.2.7.1

FDD RSRQ under Time Domain Measurement Resource Restriction with Non-MBSFN ABS (eICIC) p. 3951

9.2.7.1.1	Test purpose p. 3951
9.2.7.1.2	Test applicability p. 3951
9.2.7.1.3	Minimum conformance requirements p. 3951
9.2.7.1.4	Test description p. 3952
9.2.7.1.5	Test requirement p. 3955

9.2.8

TDD RSRQ Accuracy under Time Domain Measurement Resource Restriction with Non-MBSFN ABS p. 3957

9.2.8.1

TDD RSRQ under Time Domain Measurement Resource Restriction with Non-MBSFN ABS (eICIC) p. 3957

9.2.8.1.1	Test purpose p. 3957
9.2.8.1.2	Test applicability p. 3957
9.2.8.1.3	Minimum conformance requirements p. 3957
9.2.8.1.4	Test description p. 3958
9.2.8.1.5	Test requirement p. 3961

9.2.9

FDD RSRQ Accuracy under Time Domain Measurement Resource Restriction with MBSFN ABS p. 3963

9.2.9.1

FDD Absolute RSRQ under Time Domain Measurement Resource Restriction with MBSFN ABS (eICIC) p. 3963

9.2.9.1.1	Test purpose p. 3963
9.2.9.1.2	Test applicability p. 3963
9.2.9.1.3	Minimum conformance requirements p. 3963
9.2.9.1.4	Test description p. 3964
9.2.9.1.5	Test requirement p. 3967

9.2.10

TDD RSRQ Accuracy under Time Domain Measurement Resource Restriction with MBSFN ABS p. 3969

9.2.10.1

TDD RSRQ under Time Domain Measurement Resource Restriction with MBSFN ABS (eICIC) p. 3969

9.2.10.1.1	Test purpose p. 3969
9.2.10.1.2	Test applicability p. 3969
9.2.10.1.3	Minimum conformance requirements p. 3969
9.2.10.1.4	Test description p. 3971
9.2.10.1.5	Test requirement p. 3974

9.2.11

FDD RSRQ for E-UTRA Carrier Aggregation for 20MHz p. 3975

9.2.11.1

FDD Absolute RSRQ Accuracy for E-UTRA Carrier Aggregation for 20MHz p. 3975

9.2.11.1.1	Test purpose p. 3975
9.2.11.1.2	Test applicability p. 3975
9.2.11.1.3	Minimum conformance requirements p. 3976
9.2.11.1.4	Test description p. 3976
9.2.11.1.5	Test requirement p. 3978

9.2.11.2

FDD Relative RSRQ Accuracy for E-UTRA Carrier Aggregation for 20MHz p. 3979

9.2.11.2.1	Test purpose p. 3979
9.2.11.2.2	Test applicability p. 3979
9.2.11.2.3	Minimum conformance requirements p. 3979
9.2.11.2.4	Test description p. 3980
9.2.11.2.5	Test requirement p. 3981

9.2.12

TDD RSRQ for E-UTRA Carrier Aggregation for 20MHz p. 3982

9.2.12.1

TDD Absolute RSRQ Accuracy for E-UTRA Carrier Aggregation for 20MHz p. 3982

9.2.12.1.1	Test purpose p. 3982
9.2.12.1.2	Test applicability p. 3983
9.2.12.1.3	Minimum conformance requirements p. 3983
9.2.12.1.4	Test description p. 3984
9.2.12.1.5	Test requirement p. 3985

9.2.12.2

TDD Relative RSRQ Accuracy for E-UTRA Carrier Aggregation for 20MHz p. 3986

9.2.12.2.1	Test purpose p. 3986
9.2.12.2.2	Test applicability p. 3986
9.2.12.2.3	Minimum conformance requirements p. 3986
9.2.12.2.4	Test description p. 3987
9.2.12.2.5	Test requirement p. 3988

9.2.13

- p. 3989

9.2.14

- p. 3989

9.2.15

FDD RSRQ Accuracy under Time Domain Measurement Resource Restriction with CRS Assistance Information and Non-MBSFN ABS p. 3989

9.2.15.1

FDD RSRQ Accuracy under Time Domain Measurement Resource Restriction with CRS Assistance Information and Non-MBSFN ABS (feICIC) p. 3989

9.2.15.1.1	Test purpose p. 3989
9.2.15.1.2	Test applicability p. 3990
9.2.15.1.3	Minimum conformance requirements p. 3990
9.2.15.1.4	Test description p. 3991
9.2.15.1.5	Test requirement p. 3994

9.2.16

TDD RSRQ Accuracy under Time Domain Measurement Resource Restriction with CRS Assistance Information and Non-MBSFN ABS p. 3996

9.2.16.1

TDD RSRQ Accuracy under Time Domain Measurement Resource Restriction with CRS Assistance Information and Non-MBSFN ABS (feICIC) p. 3996

9.2.16.1.1	Test purpose p. 3996
9.2.16.1.2	Test applicability p. 3996
9.2.16.1.3	Minimum conformance requirements p. 3996
9.2.16.1.4	Test description p. 3997
9.2.16.1.5	Test requirement p. 4000

9.2.17

FDD Intra frequency RSRQ Accuracy for 5MHz Bandwidth p. 4002

9.2.17.1

FDD Intra Frequency Absolute RSRQ Accuracy for 5MHz Bandwidth p. 4002

9.2.17.1.1	Test purpose p. 4002
9.2.17.1.2	Test applicability p. 4002
9.2.17.1.3	Minimum conformance requirements p. 4002
9.2.17.1.4	Test description p. 4003
9.2.17.1.5	Test requirement p. 4003

9.2.18

FDD - FDD Inter frequency RSRQ Accuracy for 5MHz Bandwidth p. 4004

9.2.18.1

FDD - FDD Inter Frequency Absolute RSRQ Accuracy for 5MHz Bandwidth p. 4004

9.2.18.1.1	Test purpose p. 4004
9.2.18.1.2	Test applicability p. 4004
9.2.18.1.3	Minimum conformance requirements p. 4004
9.2.18.1.4	Test description p. 4005
9.2.18.1.5	Test requirement p. 4005

9.2.18.2

FDD - FDD Inter Frequency Relative Accuracy of RSRQ for 5MHz Bandwidth p. 4007

9.2.18.2.1	Test purpose p. 4007
9.2.18.2.2	Test applicability p. 4007
9.2.18.2.3	Minimum conformance requirements p. 4007
9.2.18.2.4	Test description p. 4008
9.2.18.2.5	Test requirement p. 4009

9.2.19

FDD-FDD Inter Frequency WB-RSRQ p. 4010

9.2.19.1

FDD-FDD Inter Frequency absolute WB-RSRQ accuracy p. 4010

9.2.19.1.1	Test purpose p. 4010
9.2.19.1.2	Test applicability p. 4011
9.2.19.1.3	Minimum conformance requirements p. 4011
9.2.19.1.4	Test description p. 4012
9.2.19.1.5	Test requirement p. 4012

9.2.20

TDD-TDD Inter Frequency WB-RSRQ p. 4014

9.2.20.1

TDD-TDD Inter Frequency absolute WB-RSRQ accuracy p. 4014

9.2.20.1.1	Test purpose p. 4014
9.2.20.1.2	Test applicability p. 4014
9.2.20.1.3	Minimum conformance requirements p. 4014
9.2.20.1.4	Test description p. 4015
9.2.20.1.5	Test requirement p. 4016

9.2.21

FDD RSRQ Accuracy for E-UTRA Carrier Aggregation for 10MHz+5MHz p. 4017

9.2.21.1

FDD Absolute RSRQ Accuracy for E-UTRA Carrier Aggregation for 10MHz+5MHz p. 4017

9.2.21.1.1	Test purpose p. 4017
9.2.21.1.2	Test applicability p. 4017
9.2.21.1.3	Minimum conformance requirements p. 4018
9.2.21.1.4	Test description p. 4018
9.2.21.1.5	Test requirement p. 4018

9.2.21.2

FDD Relative RSRQ Accuracy for E-UTRA Carrier Aggregation for 10MHz+5MHz p. 4019

9.2.21.2.1	Test purpose p. 4019
9.2.21.2.2	Test applicability p. 4020
9.2.21.2.3	Minimum conformance requirements p. 4020
9.2.21.2.4	Test description p. 4020
9.2.21.2.5	Test requirement p. 4020

9.2.22

TDD RSRQ Accuracy for E-UTRA Carrier Aggregation for 10MHz+5MHz p. 4022

9.2.22.1

TDD Absolute RSRQ Accuracy for E-UTRA Carrier Aggregation for 10MHz+5MHz p. 4022

9.2.22.1.1	Test purpose p. 4022
9.2.22.1.2	Test applicability p. 4022
9.2.22.1.3	Minimum conformance requirements p. 4022
9.2.22.1.4	Test description p. 4022
9.2.22.1.5	Test requirement p. 4023

9.2.22.2

TDD Relative RSRQ Accuracy for E-UTRA Carrier Aggregation for 10MHz+5MHz p. 4024

9.2.22.2.1	Test purpose p. 4024
9.2.22.2.2	Test applicability p. 4024
9.2.22.2.3	Minimum conformance requirements p. 4024
9.2.22.2.4	Test description p. 4024
9.2.22.2.5	Test requirement p. 4025

9.2.23

FDD RSRQ Accuracy for E-UTRA Carrier Aggregation for 5MHz+5MHz p. 4026

9.2.23.1

FDD Absolute RSRQ Accuracy for E-UTRA Carrier Aggregation for 5MHz+5MHz p. 4026

9.2.23.1.1	Test purpose p. 4026
9.2.23.1.2	Test applicability p. 4026
9.2.23.1.3	Minimum conformance requirements p. 4026
9.2.23.1.4	Test description p. 4026
9.2.23.1.5	Test requirement p. 4027

9.2.23.2

FDD Relative RSRQ Accuracy for E-UTRA Carrier Aggregation for 5MHz+5MHz p. 4028

9.2.23.2.1	Test purpose p. 4028
9.2.23.2.2	Test applicability p. 4028
9.2.23.2.3	Minimum conformance requirements p. 4028
9.2.23.2.4	Test description p. 4028
9.2.23.2.5	Test requirement p. 4029

9.2.24

TDD RSRQ Accuracy for E-UTRA Carrier Aggregation for 5MHz+5MHz p. 4030

9.2.24.1

TDD Absolute RSRQ Accuracy for E-UTRA Carrier Aggregation for 5MHz+5MHz p. 4030

9.2.24.1.1	Test purpose p. 4030
9.2.24.1.2	Test applicability p. 4030
9.2.24.1.3	Minimum conformance requirements p. 4030
9.2.24.1.4	Test description p. 4030
9.2.24.1.5	Test requirement p. 4031

9.2.24.2

TDD Relative RSRQ Accuracy for E-UTRA Carrier Aggregation for 5MHz+5MHz p. 4032

9.2.24.2.1	Test purpose p. 4032
9.2.24.2.2	Test applicability p. 4032
9.2.24.2.3	Minimum conformance requirements p. 4032
9.2.24.2.4	Test description p. 4032
9.2.24.2.5	Test requirement p. 4033

9.2.25

RSRQ for E-UTRAN TDD-FDD Carrier Aggregation with PCell in FDD p. 4034

9.2.25.1

Absolute RSRQ Accuracy for E-UTRAN TDD-FDD Carrier Aggregation with PCell in FDD p. 4034

9.2.25.1.1	Test purpose p. 4034
9.2.25.1.2	Test applicability p. 4034
9.2.25.1.3	Minimum conformance requirements p. 4034
9.2.25.1.4	Test description p. 4035
9.2.25.1.5	Test requirement p. 4038

9.2.25.2

Relative RSRQ Accuracy for E-UTRAN TDD-FDD Carrier Aggregation with PCell in FDD p. 4040

9.2.25.2.1	Test purpose p. 4040
9.2.25.2.2	Test applicability p. 4040
9.2.25.2.3	Minimum conformance requirements p. 4040
9.2.25.2.4	Test description p. 4041
9.2.25.2.5	Test requirement p. 4044

9.2.26

RSRQ for E-UTRAN TDD-FDD Carrier Aggregation with PCell in TDD p. 4046

9.2.26.1

Absolute RSRQ Accuracy for E-UTRAN TDD-FDD Carrier Aggregation with PCell in TDD p. 4046

9.2.26.1.1	Test purpose p. 4046
9.2.26.1.2	Test applicability p. 4046
9.2.26.1.3	Minimum conformance requirements p. 4046
9.2.26.1.4	Test description p. 4047
9.2.26.1.5	Test requirement p. 4050

9.2.26.2

Relative RSRQ Accuracy for E-UTRAN TDD-FDD Carrier Aggregation with PCell in TDD p. 4052

9.2.26.2.1	Test purpose p. 4052
9.2.26.2.2	Test applicability p. 4052
9.2.26.2.3	Minimum conformance requirements p. 4052
9.2.26.2.4	Test description p. 4053
9.2.26.2.5	Test requirement p. 4056

9.2.27

TDD RSRQ Accuracy for E-UTRA Carrier Aggregation for 20MHz+10MHz p. 4058

9.2.27.1

TDD Absolute RSRQ Accuracy for E-UTRA Carrier Aggregation for 20MHz+10MHz p. 4058

9.2.27.1.1	Test purpose p. 4058
9.2.27.1.2	Test applicability p. 4058
9.2.27.1.3	Minimum conformance requirements p. 4058
9.2.27.1.4	Test description p. 4058
9.2.27.1.5	Test requirement p. 4059

9.2.27.2

TDD Relative RSRQ Accuracy for E-UTRA Carrier Aggregation for 20MHz+10MHz p. 4060

9.2.27.2.1	Test purpose p. 4060
9.2.27.2.2	Test applicability p. 4060
9.2.27.2.3	Minimum conformance requirements p. 4060
9.2.27.2.4	Test description p. 4061
9.2.27.2.5	Test requirement p. 4061

9.2.28

FDD intra-frequency absolute RSRQ accuracy with CRS based discovery signal p. 4062

9.2.28.1

Test purpose p. 4062

9.2.28.2

Test applicability p. 4063

9.2.28.3

Minimum conformance requirements p. 4063

9.2.28.4

Test description p. 4064

9.2.28.4.1	Initial conditions p. 4064
9.2.28.4.2	Test procedure p. 4064
9.2.28.4.3	Message contents p. 4064

9.2.28.5

Test requirement p. 4065

9.2.29

TDD intra-frequency absolute RSRQ accuracy with CRS based discovery signal p. 4067

9.2.29.1

Test purpose p. 4067

9.2.29.2

Test applicability p. 4067

9.2.29.3

Minimum conformance requirements p. 4067

9.2.29.4

Test description p. 4067

9.2.29.4.1	Initial conditions p. 4067
9.2.29.4.2	Test procedure p. 4067
9.2.29.4.3	Message contents p. 4068

9.2.29.5

Test requirement p. 4069

9.2.30

FDD-FDD inter-frequency absolute and relative RSRQ accuracies with CRS based discovery signal p. 4070

9.2.30.1

Test purpose p. 4070

9.2.30.2

Test applicability p. 4070

9.2.30.3

Minimum conformance requirements p. 4070

9.2.30.4

Test description p. 4072

9.2.30.4.1	Initial conditions p. 4072
9.2.30.4.2	Test procedure p. 4072
9.2.30.4.3	Message contents p. 4073

9.2.30.5

Test requirement p. 4074

9.2.31

TDD-TDD inter-frequency absolute and relative RSRQ accuracies with CRS based discovery signal p. 4075

9.2.31.1

Test purpose p. 4075

9.2.31.2

Test applicability p. 4076

9.2.31.3

Minimum conformance requirements p. 4076

9.2.31.4

Test description p. 4076

9.2.31.4.1	Initial conditions p. 4076
9.2.31.4.2	Test procedure p. 4076
9.2.31.4.3	Message contents p. 4076

9.2.31.5

Test requirement p. 4077

9.2.32

FDD absolute and relative RSRQ accuracy for E-UTRAN Carrier Aggregation in CRS based discovery signal p. 4079

9.2.32.1

Test purpose p. 4079

9.2.32.2

Test applicability p. 4079

9.2.32.3

Minimum conformance requirements p. 4079

9.2.32.4

Test description p. 4081

9.2.32.4.1	Initial conditions p. 4081
9.2.32.4.2	Test procedure p. 4081
9.2.32.4.3	Message contents p. 4082

9.2.32.5

Test requirement p. 4082

9.2.33

TDD absolute and relative RSRQ accuracy for E-UTRAN Carrier Aggregation in CRS based discovery signal p. 4084

9.2.33.1

Test purpose p. 4084

9.2.33.2

Test applicability p. 4084

9.2.33.3

Minimum conformance requirements p. 4084

9.2.33.4

Test description p. 4084

9.2.33.4.1	Initial conditions p. 4084
9.2.33.4.2	Test procedure p. 4085
9.2.33.4.3	Message contents p. 4085

9.2.33.5

Test requirement p. 4085

9.2.34_41

- p. 4087

9.2.42

FD-FDD RSRQ Intra frequency case for UE category 0 p. 4087

9.2.42.1

FD-FDD Intra Frequency Absolute RSRQ Accuracy for UE category 0 p. 4087

9.2.42.1.1	Test purpose p. 4087
9.2.42.1.2	Test applicability p. 4087
9.2.42.1.3	Minimum conformance requirements p. 4087
9.2.42.1.4	Test description p. 4088
9.2.42.1.5	Test requirement p. 4089

9.2.43

HD-FDD RSRQ Intra frequency case for UE category 0 p. 4091

9.2.43.1

HD-FDD Intra Frequency Absolute RSRQ Accuracy for UE category 0 p. 4091

9.2.43.1.1	Test purpose p. 4091
9.2.43.1.2	Test applicability p. 4091
9.2.43.1.3	Minimum conformance requirements p. 4091
9.2.43.1.4	Test description p. 4092
9.2.43.1.5	Test requirement p. 4094

9.2.44

TDD RSRQ Intra frequency case for UE category 0 p. 4095

9.2.44.1

TDD Intra Frequency Absolute RSRQ Accuracy for UE category 0 p. 4095

9.2.44.1.1	Test purpose p. 4095
9.2.44.1.2	Test applicability p. 4096
9.2.44.1.3	Minimum conformance requirements p. 4096
9.2.44.1.4	Test description p. 4096
9.2.44.1.5	Test requirement p. 4098

9.2.45_50

- p. 4099

9.2.51

FS3 Intra frequency absolute and relative RSRQ accuracies with FDD PCell p. 4099

9.2.51.1

Test purpose p. 4099

9.2.51.2

Test applicability p. 4099

9.2.51.3

Minimum conformance requirements p. 4099

9.2.51.4

Test description p. 4101

9.2.51.4.1	Initial conditions p. 4101
9.2.51.4.2	Test procedure p. 4102
9.2.51.4.3	Message contents p. 4102

9.2.51.5

Test requirement p. 4103

9.2.52

FS3 Intra frequency absolute and relative RSRQ accuracies with TDD PCell p. 4106

9.2.52.1

Test purpose p. 4106

9.2.52.2

Test applicability p. 4106

9.2.52.3

Minimum conformance requirements p. 4106

9.2.52.4

Test description p. 4107

9.2.52.4.1	Initial conditions p. 4107
9.2.52.4.2	Test procedure p. 4108
9.2.52.4.3	Message contents p. 4109

9.2.52.5

Test requirement p. 4109

9.2.53_54

- p. 4111

9.2.55

3DL RSRQ for E-UTRAN in Carrier Aggregation with generic duplex modes p. 4112

9.2.55.1

Test purpose p. 4112

9.2.55.2

Test applicability p. 4112

9.2.55.3

Minimum conformance requirements p. 4112

9.2.55.4

Test description p. 4114

9.2.55.4.1	Initial conditions p. 4114
9.2.55.4.2	Test procedure p. 4114
9.2.55.4.3	Message contents p. 4115

9.2.55.5

Test requirement p. 4115

9.2.56

4 DL RSRQ for E-UTRAN in Carrier Aggregation with generic duplex modes p. 4118

9.2.56.1

Test purpose p. 4118

9.2.56.2

Test applicability p. 4118

9.2.56.3

Minimum conformance requirements p. 4119

9.2.56.4

Test description p. 4120

9.2.56.4.1	Initial conditions p. 4120
9.2.56.4.2	Test procedure p. 4121
9.2.56.4.3	Message contents p. 4122

9.2.56.5

Test requirement p. 4122

9.2.57

5 DL RSRQ for E-UTRAN in Carrier Aggregation with generic duplex modes p. 4126

9.2.57.1

Test purpose p. 4126

9.2.57.2

Test applicability p. 4126

9.2.57.3

Minimum conformance requirements p. 4126

9.2.57.4

Test description p. 4128

9.2.57.4.1	Initial conditions p. 4128
9.2.57.4.2	Test procedure p. 4128
9.2.57.4.3	Message contents p. 4129

9.2.57.5

Test requirement p. 4129

9.2.58

6 DL RSRQ for E-UTRAN in Carrier Aggregation with generic duplex modes p. 4133

9.2.58.1

Test purpose p. 4133

9.2.58.2

Test applicability p. 4133

9.2.58.3

Minimum conformance requirements p. 4133

9.2.58.4

Test description p. 4135

9.2.58.4.1	Initial conditions p. 4135
9.2.58.4.2	Test procedure p. 4135
9.2.58.4.3	Message contents p. 4136

9.2.58.5

Test requirement p. 4136

9.2.59

7 DL RSRQ for E-UTRAN in Carrier Aggregation with generic duplex modes p. 4140

9.2.59.1

Test purpose p. 4140

9.2.59.2

Test applicability p. 4140

9.2.59.3

Minimum conformance requirements p. 4140

9.2.59.4

Test description p. 4142

9.2.59.4.1	Initial conditions p. 4142
9.2.59.4.2	Test procedure p. 4142
9.2.59.4.3	Message contents p. 4143

9.2.59.5

Test requirement p. 4143

9.3

UTRA FDD CPICH RSCP p. 4149

9.3.1

E-UTRAN FDD - UTRA FDD CPICH RSCP absolute accuracy p. 4149

9.3.1.1

Test purpose p. 4149

9.3.1.2

Test applicability p. 4149

9.3.1.3

Minimum conformance requirements p. 4149

9.3.1.4

Test description p. 4150

9.3.1.4.1	Initial conditions p. 4150
9.3.1.4.2	Test procedure p. 4150
9.3.1.4.3	Message contents p. 4151

9.3.1.5

Test requirement p. 4152

9.3.2

E-UTRAN TDD - UTRA FDD CPICH RSCP absolute accuracy p. 4154

9.3.2.1

Test purpose p. 4154

9.3.2.2

Test applicability p. 4154

9.3.2.3

Minimum conformance requirements p. 4155

9.3.2.4

Test description p. 4155

9.3.2.4.1	Initial conditions p. 4155
9.3.2.4.2	Test procedure p. 4156
9.3.2.4.3	Message contents p. 4156

9.3.2.5

Test requirement p. 4158

9.3.3

E-UTRAN FDD - UTRA FDD CPICH RSCP absolute accuracy for 5MHz bandwidth p. 4160

9.3.3.1

Test purpose p. 4160

9.3.3.2

Test applicability p. 4160

9.3.3.3

Minimum conformance requirements p. 4160

9.3.3.4

Test description p. 4161

9.3.3.4.1	Initial conditions p. 4161
9.3.3.4.2	Test procedure p. 4161
9.3.3.4.3	Message contents p. 4161

9.3.3.5

Test requirement p. 4162

9.4

UTRAN FDD CPICH Ec/No p. 4162

9.4.1

E-UTRAN FDD - UTRA FDD CPICH Ec/No absolute accuracy p. 4162

9.4.1.1

Test purpose p. 4162

9.4.1.2

Test applicability p. 4162

9.4.1.3

Minimum conformance requirements p. 4162

9.4.1.4

Test description p. 4164

9.4.1.4.1	Initial conditions p. 4164
9.4.1.4.2	Test procedure p. 4164
9.4.1.4.3	Message contents p. 4164

9.4.1.5

Test requirement p. 4166

9.4.2

E-UTRAN TDD - UTRA FDD CPICH Ec/No absolute accuracy p. 4168

9.4.2.1

Test purpose p. 4168

9.4.2.2

Test applicability p. 4168

9.4.2.3

Minimum conformance requirements p. 4168

9.4.2.4

Test description p. 4169

9.4.2.4.1	Initial conditions p. 4169
9.4.2.4.2	Test procedure p. 4170
9.4.2.4.3	Message contents p. 4171

9.4.2.5

Test requirement p. 4172

9.4.3

E-UTRAN FDD - UTRA FDD CPICH Ec/No absolute accuracy for 5MHz bandwidth p. 4173

9.4.3.1

Test purpose p. 4173

9.4.3.2

Test applicability p. 4174

9.4.3.3

Minimum conformance requirements p. 4174

9.4.3.4

Test description p. 4174

9.4.3.4.1	Initial conditions p. 4174
9.4.3.4.2	Test procedure p. 4175
9.4.3.4.3	Message contents p. 4175

9.4.3.5

Test requirement p. 4175

9.5

UTRAN TDD P-CCPCH RSCP p. 4176

9.5.1

E-UTRAN FDD - UTRA TDD P-CCPCH RSCP absolute accuracy p. 4176

9.5.1.1

Test purpose p. 4176

9.5.1.2

Test applicability p. 4176

9.5.1.3

Minimum conformance requirements p. 4176

9.5.1.4

Test description p. 4177

9.5.1.4.1	Initial conditions p. 4177
9.5.1.4.2	Test procedure p. 4178
9.5.1.4.3	Message contents p. 4178

9.5.1.5

Test requirement p. 4179

9.5.2

E-UTRAN TDD - UTRA TDD P-CCPCH RSCP absolute accuracy p. 4181

9.5.2.1

Test purpose p. 4181

9.5.2.2

Test applicability p. 4181

9.5.2.3

Minimum conformance requirements p. 4181

9.5.2.4

Test description p. 4182

9.5.2.4.1	Initial conditions p. 4182
9.5.2.4.2	Test procedure p. 4183
9.5.2.4.3	Message contents p. 4183

9.5.2.5

Test requirement p. 4184

9.6

GSM carrier RSSI p. 4186

9.6.1

GSM RSSI accuracy for E-UTRAN FDD p. 4186

9.6.1.1

Test purpose p. 4186

9.6.1.2

Test applicability p. 4186

9.6.1.3

Minimum conformance requirements p. 4186

9.6.1.4

Test description p. 4188

9.6.1.4.1	Initial conditions p. 4188
9.6.1.4.2	Test procedure p. 4188
9.6.1.4.3	Message contents p. 4189

9.6.1.5

Test requirement p. 4190

9.6.2

GSM RSSI accuracy for E-UTRAN TDD p. 4192

9.6.2.1

Test purpose p. 4192

9.6.2.2

Test applicability p. 4192

9.6.2.3

Minimum conformance requirements p. 4192

9.6.2.4

Test description p. 4194

9.6.2.4.1	Initial conditions p. 4194
9.6.2.4.2	Test procedure p. 4194
9.6.2.4.3	Message contents p. 4195

9.6.2.5

Test requirement p. 4196

9.7

UE Rx - Tx Time Difference p. 4198

9.8

RSTD p. 4198

9.9

Serving Cell RSRP and RSRQ p. 4198

9.9.1

FDD Serving Cell RSRP and RSRQ Accuracy p. 4198

9.9.1.1

FDD Intra Frequency Serving Cell Absolute RSRP Accuracy p. 4198

9.9.1.1.1	Test purpose p. 4198
9.9.1.1.2	Test applicability p. 4198
9.9.1.1.3	Minimum conformance requirements p. 4198
9.9.1.1.4	Test description p. 4199
9.9.1.1.5	Test requirement p. 4200

9.9.1.1_1

FDD Intra Frequency Serving Cell Absolute RSRP Accuracy (Rel 12 and forward) p. 4202

9.9.1.1_1.1	Test purpose p. 4202
9.9.1.1_1.2	Test applicability p. 4202
9.9.1.1_1.3	Minimum conformance requirements p. 4203
9.9.1.1_1.4	Test description p. 4203
9.9.1.1_1.5	Test requirement p. 4204

9.9.1.2

FDD Intra Frequency Serving Cell Absolute RSRQ Accuracy p. 4206

9.9.1.2.1	Test purpose p. 4206
9.9.1.2.2	Test applicability p. 4206
9.9.1.2.3	Minimum conformance requirements p. 4206
9.9.1.2.4	Test description p. 4207
9.9.1.2.5	Test requirement p. 4208

9.9.2

TDD Serving Cell RSRP and RSRQ Accuracy p. 4210

9.9.2.1

TDD Intra Frequency Serving Cell Absolute RSRP Accuracy p. 4210

9.9.2.1.1	Test purpose p. 4210
9.9.2.1.2	Test applicability p. 4210
9.9.2.1.3	Minimum conformance requirements p. 4210
9.9.2.1.4	Test description p. 4211
9.9.2.1.5	Test requirement p. 4212

9.9.2.1_1

TDD Intra Frequency Serving Cell Absolute RSRP Accuracy (Rel 12 and forward) p. 4213

9.9.2.1_1.1	Test purpose p. 4213
9.9.2.1_1.2	Test applicability p. 4213
9.9.2.1_1.3	Minimum conformance requirements p. 4213
9.9.2.1_1.4	Test description p. 4214
9.9.2.1_1.5	Test requirement p. 4215

9.9.2.2

TDD Intra Frequency Serving Cell Absolute RSRQ Accuracy p. 4216

9.9.2.2.1	Test purpose p. 4216
9.9.2.2.2	Test applicability p. 4216
9.9.2.2.3	Minimum conformance requirements p. 4216
9.9.2.2.4	Test description p. 4217
9.9.2.2.5	Test requirement p. 4218

9.10

- p. 4219

9.11

RSSI Accuracy p. 4219

9.11.1

FS3 average RSSI accuracy case (PCell using FDD) p. 4219

9.11.1.1

Test purpose p. 4219

9.11.1.2

Test applicability p. 4220

9.11.1.3

Minimum conformance requirements p. 4220

9.11.1.4

Test description p. 4220

9.11.1.4.1	Initial conditions p. 4220
9.11.1.4.2	Test procedure p. 4221
9.11.1.4.3	Message contents p. 4221

9.11.1.5

Test requirement p. 4222

9.11.2

FS3 average RSSI accuracy case (PCell using TDD) p. 4223

9.11.2.1

Test purpose p. 4223

9.11.2.2

Test applicability p. 4223

9.11.2.3

Minimum conformance requirements p. 4223

9.11.2.4

Test description p. 4223

9.11.2.4.1	Initial conditions p. 4223
9.11.2.4.2	Test procedure p. 4224
9.11.2.4.3	Message contents p. 4224

9.11.2.5

Test requirement p. 4224

9.12

Channel Occupancy p. 4225

9.12.1

FS3 channel occupancy test (PCell using FDD) p. 4225

9.12.1.1

Test purpose p. 4225

9.12.1.2

Test applicability p. 4225

9.12.1.3

Minimum conformance requirements p. 4226

9.12.1.4

Test description p. 4226

9.12.1.4.1	Initial conditions p. 4226
9.12.1.4.2	Test procedure p. 4226
9.12.1.4.3	Message contents p. 4227

9.12.1.5

Test requirement p. 4227

9.12.2

FS3 channel occupancy test (PCell using TDD) p. 4228

9.12.2.1

Test purpose p. 4228

9.12.2.2

Test applicability p. 4229

9.12.2.3

Minimum conformance requirements p. 4229

9.12.2.4

Test description p. 4229

9.12.2.4.1	Initial conditions p. 4229
9.12.2.4.2	Test procedure p. 4229
9.12.2.4.3	Message contents p. 4229

9.12.2.5

Test requirement p. 4229

Proximity-based Services in Any Cell Selection p. 4231

10.1

FFS p. 4231

10.2

E-UTRAN FDD - Initiation/Cease of SLSS Transmission with ProSe Direct Communication p. 4231

10.2.1

Test purpose p. 4231

10.2.2

Test applicability p. 4231

10.2.3

Minimum conformance requirements p. 4231

10.2.4

Test description p. 4231

10.2.4.1	Initial conditions p. 4231
10.2.4.2	Test procedure p. 4233
10.2.4.3	Message contents p. 4233

10.2.5

Test requirement p. 4233

10.3

FFS p. 4234

10.4

E-UTRAN FDD - Initiation/Cease of SLSS Transmission with ProSe Direct Communication p. 4235

10.4.1

Test purpose p. 4235

10.4.2

Test applicability p. 4235

10.4.3

Minimum conformance requirements p. 4235

10.4.4

Test description p. 4235

10.4.4.1	Initial conditions p. 4235
10.4.4.2	Test procedure p. 4237
10.4.4.3	Message contents p. 4237

10.4.5

Test requirement p. 4238

V2V Sidelink Communication for V2V Operation on Dedicated V2V Carrier p. 4239

11.1

V2V UE Transmission Timing Accuracy Test p. 4239

11.1.1

Test purpose p. 4239

11.1.2

Test applicability p. 4239

11.1.3

Minimum conformance requirements p. 4240

11.1.4

Test description p. 4240

11.1.4.1	Initial conditions p. 4240
11.1.4.2	Test procedure p. 4241
11.1.4.3	Message contents p. 4241

11.1.5

Test requirement p. 4242

11.2

Interruptions due to V2V sidelink communication p. 4242

11.2.1

Test purpose p. 4242

11.2.2

Test applicability p. 4242

11.2.3

Minimum conformance requirements p. 4242

11.2.4

Test description p. 4242

11.2.4.1	Initial conditions p. 4242
11.2.4.2	Test procedure p. 4243
11.2.4.3	Message contents p. 4243

11.2.5

Test requirement p. 4244

V2X Communications p. 4244

12.1

V2X UE Transmission Timing Accuracy Test p. 4244

12.1.1

V2X UE Transmission Timing Accuracy Test for eNB as Timing Reference p. 4245

12.1.1.1

Test Purpose p. 4245

12.1.1.2

Applicability of requirements p. 4245

12.1.1.3

Minimum Conformance Requirements p. 4245

12.1.1.4

Test Description p. 4245

12.1.1.4.1	Initial Conditions p. 4245
12.1.1.4.2	Test Procedure p. 4246
12.1.1.4.3	Message Contents p. 4246

12.1.1.5

Test Requirement p. 4246

12.1.2

V2X UE Transmission Timing Accuracy Test for SyncRef UE as Timing Reference p. 4247

12.1.2.1

Test Purpose p. 4247

12.1.2.2

Applicability of requirements p. 4247

12.1.2.3

Minimum Conformance Requirements p. 4247

12.1.2.4

Test Description p. 4248

12.1.2.4.1	Initial Conditions p. 4248
12.1.2.4.2	Test Procedure p. 4248
12.1.2.4.3	Message Contents p. 4248

12.1.2.5

Test Requirement p. 4250

12.2

Initiation/Cease of SLSS Transmission with V2X Sidelink Communication p. 4251

12.2.1

Initiation/Cease of SLSS Transmission with V2X Sidelink Communication for eNB as Timing Reference p. 4251

12.2.1.1

Test purpose p. 4251

12.2.1.2

Test applicability p. 4251

12.2.1.3

Minimum conformance requirements p. 4251

12.2.1.4

Test description p. 4252

12.2.1.4.1	Initial conditions p. 4252
12.2.1.4.2	Test procedure p. 4253
12.2.1.4.3	Message contents p. 4253

12.2.1.5

Test requirement p. 4256

12.2.2

Initiation/Cease of SLSS Transmission with V2X Sidelink Communication for SyncRef UE as Timing Reference p. 4257

12.2.2.1

Test purpose p. 4257

12.2.2.2

Test applicability p. 4257

12.2.2.3

Minimum conformance requirements p. 4257

12.2.2.4

Test description p. 4258

12.2.2.4.1	Initial conditions p. 4258
12.2.2.4.2	Test procedure p. 4258
12.2.2.4.3	Message contents p. 4259

12.2.2.5

Test requirement p. 4260

12.3

V2X Synchronization Reference Selection/Reselection Tests p. 4261

12.3.1

V2X Synchronization Reference Selection/Reselection Tests for GNSS configured as the highest priority p. 4261

12.3.1.1

Test Purpose p. 4261

12.3.1.2

Applicability of requirements p. 4261

12.3.1.3

Minimum Conformance Requirements p. 4261

12.3.1.4

Test Description p. 4262

12.3.1.4.1	Initial Conditions p. 4262
12.3.1.4.2	Test Procedure p. 4263
12.3.1.4.3	Message Contents p. 4264

12.3.1.5

Test Requirement p. 4266

12.3.2

V2X Synchronization Reference Selection/Reselection Tests for eNB configured as the highest priority p. 4268

12.3.2.1

Test Purpose p. 4268

12.3.2.2

Applicability of requirements p. 4268

12.3.2.3

Minimum Conformance Requirements p. 4268

12.3.2.4

Test Description p. 4269

12.3.2.4.1	Initial Conditions p. 4269
12.3.2.4.2	Test Procedure p. 4270
12.3.2.4.3	Message Contents p. 4270

12.3.2.5

Test Requirement p. 4272

12.4

Congestion Control Measurement Test for V2X UE p. 4274

12.4.1

Test Purpose p. 4274

12.4.2

Test applicability p. 4274

12.4.3

Minimum conformance requirements p. 4274

12.4.4

Test description p. 4274

12.4.4.1	Initial conditions p. 4275
12.4.4.2	Test procedure p. 4276
12.4.4.3	Message contents p. 4276

12.4.5

Test requirement p. 4278

12.5

Interruptions due to V2X Sidelink Communication p. 4279

12.5.1

Test Purpose p. 4279

12.5.2

Applicability of requirements p. 4279

12.5.3

Minimum Conformance Requirements p. 4279

12.5.4

Test Description p. 4279

12.5.4.1	Initial Conditions p. 4279
12.5.4.2	Test Procedure p. 4281
12.5.4.3	Message Contents p. 4281

12.5.5

Test Requirement p. 4282

12.6

V2X UE Autonomous Resource Selection/Reselection Measurement Test p. 4283

12.6.1

V2X UE Autonomous Resource Selection/Reselection Tests for PSSCH-RSRP measurements p. 4283

12.6.1.1

Test Purpose p. 4283

12.6.1.2

Applicability of requirements p. 4283

12.6.1.3

Minimum Conformance Requirements p. 4284

12.6.1.4

Test Description p. 4284

12.6.1.4.1	Initial Conditions p. 4284
12.6.1.4.2	Test Procedure p. 4285
12.6.1.4.3	Message Contents p. 4285

12.6.1.5

Test Requirement p. 4287

12.6.2

V2X UE Autonomous Resource Selection/Reselection Tests for S-RSSI measurements p. 4288

12.6.2.1

Test Purpose p. 4288

12.6.2.2

Applicability of requirements p. 4288

12.6.2.3

Minimum Conformance Requirements p. 4288

12.6.2.4

Test Description p. 4288

12.6.2.4.1	Initial Conditions p. 4288
12.6.2.4.2	Test Procedure p. 4290
12.6.2.4.3	Message Contents p. 4290

12.6.2.5

Test Requirement p. 4292

E-UTRAN Standalone Tests for UE Category NB for Satellite Access p. 4293

13.1

RRC_IDLE state for satellite access p. 4293

13.1.1

Cell re-selection for Satellite Access p. 4293

13.1.1.1

HD - FDD Intra frequency case for UE Category NB1 Standalone mode in normal coverage p. 4293

13.1.1.1.1	Test purpose p. 4293
13.1.1.1.2	Test applicability p. 4293
13.1.1.1.3	Minimum conformance requirements p. 4293
13.1.1.1.4	Test description p. 4294
13.1.1.1.5	Test requirement p. 4296

13.1.1.1_1

HD - FDD Intra frequency case for UE Category NB1 Standalone mode in normal coverage for GSO and NGSO p. 4298

13.1.1.1_1.1	Test purpose p. 4298
13.1.1.1_1.2	Test applicability p. 4298
13.1.1.1_1.3	Minimum conformance requirements p. 4298
13.1.1.1_1.4	Test description p. 4298
13.1.1.1_1.5	Test requirement p. 4300

13.1.1.2

HD - FDD Intra frequency case for UE Category NB1 Standalone mode in normal coverage with serving cell RRM measurement relaxation p. 4300

13.1.1.2.1	Test purpose p. 4300
13.1.1.2.2	Test applicability p. 4300
13.1.1.2.3	Minimum conformance requirements p. 4300
13.1.1.2.4	Test description p. 4302
13.1.1.2.5	Test requirement p. 4304

13.1.1.2_1

HD - FDD Intra frequency case for UE Category NB1 Standalone mode in normal coverage with serving cell RRM measurement relaxation for GSO and NGSO p. 4306

13.1.1.2_1.1	Test purpose p. 4306
13.1.1.2_1.2	Test applicability p. 4306
13.1.1.2_1.3	Minimum conformance requirements p. 4306
13.1.1.2_1.4	Test description p. 4306
13.1.1.2_1.5	Test requirement p. 4308

13.1.1.3

HD - FDD Intra frequency case for UE Category NB1 Standalone mode in normal coverage with UE specific DRX p. 4308

13.1.1.3.1	Test purpose p. 4308
13.1.1.3.2	Test applicability p. 4308
13.1.1.3.3	Minimum conformance requirements p. 4308
13.1.1.3.4	Test description p. 4309
13.1.1.3.5	Test requirement p. 4312

13.1.1.3_1

HD - FDD Intra frequency case for UE Category NB1 Standalone mode in normal coverage with UE specific DRX for GSO and NGSO p. 4314

13.1.1.3_1.1	Test purpose p. 4314
13.1.1.3_1.2	Test applicability p. 4314
13.1.1.3_1.3	Minimum conformance requirements p. 4314
13.1.1.3_1.4	Test description p. 4314
13.1.1.3_1.5	Test requirement p. 4317

13.1.1.4

HD - FDD Inter frequency case for UE Category NB1 Standalone mode in normal coverage p. 4317

13.1.1.4.1	Test purpose p. 4317
13.1.1.4.2	Test applicability p. 4317
13.1.1.4.3	Minimum conformance requirements p. 4317
13.1.1.4.4	Test description p. 4318
13.1.1.4.5	Test requirement p. 4320

13.1.1.5

HD - FDD Intra frequency case for UE Category NB1 Standalone mode in enhanced coverage, location-based cell reselection for NGSO p. 4322

13.1.1.5.1	Test purpose p. 4322
13.1.1.5.2	Test applicability p. 4322
13.1.1.5.3	Minimum conformance requirements p. 4322
13.1.1.5.4	Test description p. 4323
13.1.1.5.5	Test requirement p. 4324

13.1.1.6

HD - FDD Inter frequency case for UE Category NB1 Standalone mode in enhanced coverage, time-based cell reselection for NGSO p. 4326

13.1.1.6.1	Test purpose p. 4326
13.1.1.6.2	Test applicability p. 4326
13.1.1.6.3	Minimum conformance requirements p. 4326
13.1.1.6.4	Test description p. 4327
13.1.1.6.5	Test requirement p. 4329

13.3

RRC connection mobility control for satellite access p. 4331

13.3.1

RRC re-establishment for satellite access p. 4331

13.3.1.1

HD-FDD Intra-frequency RRC Re-establishment for UE category NB1 in Standalone mode under normal coverage p. 4331

13.3.1.1.1

Test purpose p. 4331

13.3.1.1.2

Test applicability p. 4331

13.3.1.1.3

Minimum conformance requirements p. 4331

13.3.1.1.4

Test description p. 4331

13.3.1.1.4.1	Initial conditions p. 4332
13.3.1.1.4.2	Test procedure p. 4333
13.3.1.1.4.3	Message contents p. 4333

13.3.1.1.5

Test requirement p. 4333

13.3.1.1_1

HD-FDD Intra-frequency RRC Re-establishment for UE category NB1 in Standalone mode under normal coverage for GSO and NGSO p. 4334

13.3.1.1_1.1

Test purpose p. 4334

13.3.1.1_1.2

Test applicability p. 4335

13.3.1.1_1.3

Minimum conformance requirements p. 4335

13.3.1.1_1.4

Test description p. 4335

13.3.1.1_1.4.1	Initial conditions p. 4335
13.3.1.1_1.4.2	Test procedure p. 4336
13.3.1.1_1.4.3	Message contents p. 4336

13.3.1.1_1.5

Test requirement p. 4336

13.3.1.2

HD-FDD Intra-frequency RRC Re-establishment for UE category NB1 in Standalone mode under enhanced coverage p. 4336

13.3.1.2.1

Test purpose p. 4336

13.3.1.2.2

Test applicability p. 4336

13.3.1.2.3

Minimum conformance requirements p. 4336

13.3.1.2.4

Test description p. 4337

13.3.1.2.4.1	Initial conditions p. 4337
13.3.1.2.4.2	Test procedure p. 4338
13.3.1.2.4.3	Message contents p. 4338

13.3.1.2.5

Test requirement p. 4339

13.3.1.2_1

HD-FDD Intra-frequency RRC Re-establishment for UE category NB1 in Standalone mode under enhanced coverage for GSO and NGSO p. 4340

13.3.1.2_1.1

Test purpose p. 4340

13.3.1.2_1.2

Test applicability p. 4340

13.3.1.2_1.3

Minimum conformance requirements p. 4340

13.3.1.2_1.4

Test description p. 4340

13.3.1.2_1.4.1	Initial conditions p. 4340
13.3.1.2_1.4.2	Test procedure p. 4341
13.3.1.2_1.4.3	Message contents p. 4341

13.3.1.2_1.5

Test requirement p. 4341

13.3.1.3

HD-FDD Inter-frequency RRC Re-establishment for UE category NB1 in Standalone mode under enhanced coverage p. 4341

13.3.1.3.1

Test purpose p. 4341

13.3.1.3.2

Test applicability p. 4341

13.3.1.3.3

Minimum conformance requirements p. 4341

13.3.1.3.4

Test description p. 4342

13.3.1.3.4.1	Initial conditions p. 4342
13.3.1.3.4.2	Test procedure p. 4343
13.3.1.3.4.3	Message contents p. 4344

13.3.1.3.5

Test requirement p. 4344

13.3.2

Random Access for Satellite Access p. 4345

13.3.2.1

Contention Based Random Access Test for UE category NB1 UEs in Satellite Access - Standalone mode in normal coverage p. 4345

13.3.2.1.1	Test purpose p. 4345
13.3.2.1.2	Test applicability p. 4345
13.3.2.1.3	Minimum conformance requirements p. 4345
13.3.2.1.4	Test description p. 4346

13.3.2.2

Contention Based Random Access Test for UE category NB1 UEs in Satellite Access - Standalone mode in Enhanced Coverage p. 4355

13.3.2.2.1	Test purpose p. 4355
13.3.2.2.2	Test applicability p. 4355
13.3.2.2.3	Minimum conformance requirements p. 4355
13.3.2.2.4	Test description p. 4356
13.3.2.2.5	Test requirement p. 4361

13.3.2.3

Contention Based Random Access on Non-anchor Carrier Test for UE category NB1 UEs Standalone mode in Enhanced Coverage p. 4365

13.3.2.3.1	Test purpose p. 4365
13.3.2.3.2	Test applicability p. 4365
13.3.2.3.3	Minimum conformance requirements p. 4365
13.3.2.3.4	Test description p. 4366
13.3.2.3.5	Test requirement p. 4370

13.4

Timing and signalling characteristics for satellite access p. 4374

13.4.1

UE transmit timing for satellite access p. 4374

13.4.1.1

E-UTRAN HD-FDD - UE Transmit Timing Accuracy Tests for Category NB1 UE Standalone mode under normal coverage for Satellite Access p. 4374

13.4.1.1.1	Test purpose p. 4374
13.4.1.1.2	Test applicability p. 4374
13.4.1.1.3	Minimum conformance requirements p. 4374
13.4.1.1.4	Test description p. 4375
13.4.1.1.5	Test requirement p. 4378

13.4.1.2

E-UTRAN HD-FDD - UE Transmit Timing Accuracy Tests for Category NB1 UE Standalone mode under enhanced coverage for Satellite Access p. 4379

13.4.1.2.1	Test purpose p. 4379
13.4.1.2.2	Test applicability p. 4379
13.4.1.2.3	Minimum conformance requirements p. 4379
13.4.1.2.4	Test description p. 4380
13.4.1.2.5	Test requirement p. 4383

13.4.1.3

E-UTRAN HD-FDD - UE Transmit Timing Accuracy Tests for Category NB1 UE Standalone mode under enhanced coverage with segment transmission in NGSO for Satellite Access p. 4384

13.4.1.3.1	Test purpose p. 4384
13.4.1.3.2	Test applicability p. 4384
13.4.1.3.3	Minimum conformance requirements p. 4384
13.4.1.3.4	Test description p. 4385
13.4.1.3.5	Test requirement p. 4387

13.4.2

UE timing advance for satellite access p. 4388

13.4.2.1

HD-FDD UE Timing Advance Adjustment Accuracy Test for UE Category NB1 in Standalone Mode under Normal Coverage for Satellite Access p. 4388

13.4.2.1.1	Test purpose p. 4388
13.4.2.1.2	Test applicability p. 4388
13.4.2.1.3	Minimum conformance requirements p. 4389
13.4.2.1.4	Test description p. 4389
13.4.2.1.5	Test requirement p. 4392

13.4.2.2

HD-FDD UE Timing Advance Adjustment Accuracy Test for UE Category NB1 in Standalone Mode under Enhance Coverage for Satellite Access p. 4393

13.4.2.2.1	Test purpose p. 4393
13.4.2.2.2	Test applicability p. 4393
13.4.2.2.3	Minimum conformance requirements p. 4393
13.4.2.2.4	Test description p. 4394
13.4.2.2.5	Test requirement p. 4397

13.4.3

Radio Link Monitoring for satellite access p. 4398

13.4.3.1

HD-FDD Radio Link Monitoring Test for Out-of-sync in DRX for UE Category NB1 Standalone mode in Normal Coverage p. 4398

13.4.3.1.1	Test purpose p. 4398
13.4.3.1.2	Test applicability p. 4398
13.4.3.1.3	Minimum conformance requirements p. 4398
13.4.3.1.4	Test description p. 4398
13.4.3.1.5	Test requirement p. 4402

13.4.3.2

HD-FDD Radio Link Monitoring Test for Out-of-sync in DRX for UE Category NB1 Standalone mode in Enhanced Coverage p. 4404

13.4.3.2.1	Test purpose p. 4404
13.4.3.2.2	Test applicability p. 4404
13.4.3.2.3	Minimum conformance requirements p. 4404
13.4.3.2.4	Test description p. 4404
13.4.3.2.5	Test requirement p. 4408

13.4.3.3

HD-FDD Radio Link Monitoring Test for In-sync with DRX for UE Category NB1 Standalone mode in Enhanced Coverage p. 4410

13.4.3.3.1	Test purpose p. 4410
13.4.3.3.2	Test applicability p. 4410
13.4.3.3.3	Minimum conformance requirements p. 4410
13.4.3.3.4	Test description p. 4410
13.4.3.3.5	Test requirement p. 4414

13.4.3.4

HD-FDD Radio Link Monitoring Test for In-sync with DRX for UE Category NB1 Standalone mode in Normal Coverage p. 4416

13.4.3.4.1	Test purpose p. 4416
13.4.3.4.2	Test applicability p. 4416
13.4.3.4.3	Minimum conformance requirements p. 4416
13.4.3.4.4	Test description p. 4416
13.4.3.4.5	Test requirement p. 4420

13.4.3.5

HD-FDD Radio Link Monitoring Test for In-sync without DRX for UE Category NB1 Standalone mode in Normal Coverage p. 4422

13.4.3.5.1	Test purpose p. 4422
13.4.3.5.2	Test applicability p. 4422
13.4.3.5.3	Minimum conformance requirements p. 4422
13.4.3.5.4	Test description p. 4422
13.4.3.5.5	Test requirement p. 4425

13.4.3.6

HD-FDD Radio Link Monitoring Test for In-sync without DRX for UE Category NB1 Standalone mode in Enhanced Coverage p. 4426

13.4.3.6.1	Test purpose p. 4426
13.4.3.6.2	Test applicability p. 4426
13.4.3.6.3	Minimum conformance requirements p. 4427
13.4.3.6.4	Test description p. 4427
13.4.3.6.5	Test requirement p. 4430

13.4.3.7

HD-FDD Radio Link Monitoring Test for Out-of-sync without DRX for UE Category NB1 Standalone mode in Normal Coverage p. 4431

13.4.3.7.1	Test purpose p. 4431
13.4.3.7.2	Test applicability p. 4432
13.4.3.7.3	Minimum conformance requirements p. 4432
13.4.3.7.4	Test description p. 4432
13.4.3.7.5	Test requirement p. 4435

13.4.3.8

HD-FDD Radio Link Monitoring Test for Out-of-sync without DRX for UE Category NB1 Standalone mode in Enhanced Coverage p. 4436

13.4.3.8.1	Test purpose p. 4436
13.4.3.8.2	Test applicability p. 4436
13.4.3.8.3	Minimum conformance requirements p. 4437
13.4.3.8.4	Test description p. 4437
13.4.3.8.5	Test requirement p. 4440

13.5

UE measurement procedures in RRC_CONNECTED state for UE category NB1 for satellite access p. 4441

13.5.1	HD-FDD Intra-frequency neighbour cell measurement for UE category NB1 in standalone mode under normal coverage for Satellite Access p. 4441
13.5.2	HD-FDD Inter-frequency neighbour cell measurement for UE category NB1 in standalone mode under normal coverage for Satellite Access p. 4446
13.5.3	HD-FDD Intra-frequency location-based neighbour cell measurement for UE category NB1 in standalone mode under normal coverage for Satellite Access p. 4451

13.6

Measurement performance requirements for UE for satellite access p. 4455

13.6.1

Void p. …

13.6.2

Channel quality reporting accuracy for satellite access p. 4455

13.6.2.1

E-UTRAN HD-FDD Downlink channel quality reporting accuracy for UE Category NB1 Standalone mode under normal coverage p. 4455

13.6.2.1.1	Test purpose p. 4455
13.6.2.1.2	Test applicability p. 4455
13.6.2.1.3	Minimum conformance requirements p. 4455
13.6.2.1.4	Test description p. 4456
13.6.2.1.5	Test requirement p. 4457

13.6.2.2

E-UTRAN HD-FDD Downlink channel quality reporting accuracy for UE Category NB1 Standalone mode under enhanced coverage p. 4458

13.6.2.2.1	Test purpose p. 4458
13.6.2.2.2	Test applicability p. 4458
13.6.2.2.3	Minimum conformance requirements p. 4458
13.6.2.2.4	Test description p. 4459
13.6.2.2.5	Test requirement p. 4461

13.6.2.3

E-UTRAN HD-FDD Downlink channel quality reporting accuracy on non-anchor carrier for UE Category NB1 Standalone mode under normal coverage p. 4462

13.6.2.3.1	Test purpose p. 4462
13.6.2.3.2	Test applicability p. 4462
13.6.2.3.3	Minimum conformance requirements p. 4462
13.6.2.3.4	Test description p. 4462
13.6.2.3.5	Test requirement p. 4467

13.6.2.4

E-UTRAN HD-FDD Downlink channel quality reporting accuracy on non-anchor carrier for UE Category NB1 Standalone mode under enhanced coverage p. 4469

13.6.2.4.1	Test purpose p. 4469
13.6.2.4.2	Test applicability p. 4469
13.6.2.4.3	Minimum conformance requirements p. 4469
13.6.2.4.4	Test description p. 4469
13.6.2.4.5	Test requirement p. 4474

13.6.2.5

E-UTRAN HD-FDD Downlink channel quality reporting accuracy in RRC_CONNECTED for UE Category NB1 Standalone mode under normal coverage p. 4476

13.6.2.5.1	Test purpose p. 4476
13.6.2.5.2	Test applicability p. 4476
13.6.2.5.3	Minimum conformance requirements p. 4476
13.6.2.5.4	Test description p. 4476
13.6.2.5.5	Test requirement p. 4478

13.6.2.6

E-UTRAN HD-FDD Downlink channel quality reporting accuracy in RRC_CONNECTED for UE Category NB1 Standalone mode under enhanced coverage p. 4479

13.6.2.6.1	Test purpose p. 4479
13.6.2.6.2	Test applicability p. 4479
13.6.2.6.3	Minimum conformance requirements p. 4479
13.6.2.6.4	Test description p. 4480
13.6.2.6.5	Test requirement p. 4481

(Normative) Reference Measurement Channels p. 4483

A.1

PDSCH p. 4483

A.1.1	FDD p. 4483
A.1.2	TDD p. 4486
A.1.3	FDD for UE Category 0 p. 4489
A.1.4	HD-FDD for UE Category 0 p. 4489
A.1.5	TDD for UE Category 0 p. 4490
A.1.6	Frame Structure 3 p. 4491

A.2

PCFICH/PDCCH/PHICH p. 4492

A.2.1	FDD p. 4492
A.2.2	TDD p. 4492
A.2.3	HD-FDD for UE category 0 p. 4493
A.2.4	FS 3 p. 4493

A.3

PUSCH p. 4493

A.4

Reference Measurement Channels for ProSe Direct Discovery p. 4494

A.4.1

FDD p. 4494

A.5

Reference measurement channels for ProSe Direct Communication p. 4494

A.5.1

FDD p. 4494

A.6

ProSe Receive Traffic Generator p. 4495

A.6.1	ProSe Direct Communication Receive Traffic Generator for FDD p. 4495
A.6.2	ProSe Direct Discovery Receive Traffic Generator for FDD p. 4496

A.7

MPDCCH Reference Channels for Cat-M1 UEs p. 4496

A.7.1	FDD in CEModeA p. 4496
A.7.2	HD-FDD in CEModeA p. 4497
A.7.3	TDD in CEModeA p. 4497
A.7.4	FDD in CEModeB p. 4498
A.7.5	HD-FDD in CEModeB p. 4498
A.7.6	TDD in CEModeB p. 4499

A.8

PDSCH Reference Channels for Cat-M1 UEs p. 4499

A.8.1	FDD in CEModeA p. 4499
A.8.2	HD-FDD in CEModeA p. 4500
A.8.3	TDD in CEModeA p. 4500
A.8.4	FDD in CEModeB p. 4501
A.8.5	HD-FDD in CEModeB p. 4501
A.8.6	TDD in CEModeB p. 4502

A.8a

Reference Configurations for satellites for Cat-M1 UEs p. 4503

A.8a.1	General setup for SIB31 p. 4503
A.8a.2	Satellite specific configuration for serving cell p. 4503
A.8a.3	Satellite specific configuration for neighbour cell p. 4503

A.9

Reference PRACH Configurations p. 4504

A.10

General configuration for NB-IoT p. 4505

A.10.1

NPDCCH Reference Channel for UE category NB1 p. 4505

A.10.1.1	In-band operation p. 4505
A.10.1.2	Standalone operation p. 4506
A.10.1.3	Guard band operation p. 4506

A.10.2

NPDSCH Reference Channel for UE category NB1 p. 4506

A.10.2.1	HD-FDD in-band operation p. 4506
A.10.2.2	HD-FDD standalone operation p. 4507
A.10.2.3	HD-FDD guard band operation p. 4508
A.10.2.4	TDD in-band operation p. 4508
A.10.2.5	TDD standalone operation p. 4509
A.10.2.6	TDD guard band operation p. 4509

A.10.3

Reference NPRACH Configurations p. 4509

A.10.4.1	General setup for SIB-31-NB p. 4511
A.10.4.2	Satellite specific configuration for serving cell p. 4511
A.10.4.3	Satellite specific configuration for neighbour cell p. 4512

A.11

V2V Sidelink Communication on Dedicated V2V Carrier p. 4512

A.11.1	Introduction p. 4512
A.11.2	Reference resource pool configurations for V2V Sidelink Communication p. 4512
A.11.3	Reference measurement channels for V2V Sidelink Communication p. 4513

A.12

V2X sidelink communication p. 4514

A.12.1	Introduction p. 4514
A.12.2	Reference resource pool configurations for V2X Sidelink Communication p. 4514
A.12.3	Reference measurement channels for V2X Sidelink Communication p. 4517

(Normative) Propagation Conditions p. 4519

B.0	No interference p. 4519
B.1	Static propagation condition p. 4519
B.2	Multi-path fading Propagation Conditions p. 4519

(Normative) Downlink Physical Channels p. 4520

C.0

Downlink signal p. 4520

C.1

General p. 4520

C.2

Set-up p. 4520

C.3

Test specific scenarios p. 4520

C.3.1

ABS Transmission Configurations p. 4520

C.3.1.1

Non-MBSFN ABS Transmission Configurations p. 4520

C.3.1.1.1	Non-MBSFN ABS Transmission, 1x2 antenna with PBCH p. 4520
C.3.1.1.2	Non-MBSFN ABS Transmission, 2x2 antenna without PBCH p. 4521

C.3.1.2

MBSFN ABS Transmission Configurations p. 4522

C.3.1.2.1	MBSFN ABS Transmission, 1x2 antenna p. 4522
C.3.1.2.2	MBSFN ABS Transmission, 2x2 antenna p. 4522

C.3.2

Impact of Reference Sensitivity Degradation with Carrier Aggregation on Test Cases p. 4523

C.3.2.1

Impact of Reference Sensitivity Degradation due to Insertion Loss p. 4523

C.3.3

Carrier Aggregation Test Cases with Different Channel Bandwidth Combinations p. 4523

C.3.3.1

Introduction p. 4523

C.3.4

Proximity-based Services p. 4523

C.3.4.1

Introduction p. 4523

C.3.4.2

Reference DRX configurations for ProSe tests p. 4524

C.3.4.3

Test Cases with Different Channel Bandwidths p. 4524

C.3.4.3.1	Introduction p. 4524
C.3.4.3.2	Principle of testing p. 4524

C.3.5

Listen before talk model p. 4524

C.3.5.1	Introduction p. 4524
C.3.5.2	Definition p. 4524

(Normative) OFDMA Channel Noise Generator (OCNG) p. 4525

D.1

OCNG Patterns for FDD p. 4525

D.0

- p. 4525

D.1.1	OCNG FDD pattern 1: outer resource blocks allocation in 10 MHz p. 4526
D.1.2	OCNG FDD pattern 2: full bandwidth allocation in 10 MHz p. 4527
D.1.3	OCNG FDD pattern 3: outer resource blocks allocation in 1.4 MHz p. 4528
D.1.4	OCNG FDD pattern 4: full bandwidth allocation in 1.4 MHz p. 4529
D.1.5	OCNG FDD pattern 5: outer resource blocks allocation in 10 MHz (without MBSFN) p. 4529
D.1.6	OCNG FDD pattern 6: full bandwidth allocation in 10 MHz (without MBSFN) p. 4530
D.1.7	OCNG FDD pattern 7: full bandwidth allocation in 1.4 MHz (without MBSFN) p. 4530
D.1.8	OCNG FDD pattern 8: outer resource blocks allocation in 10 MHz for MBSFN ABS p. 4531
D.1.9	OCNG FDD pattern 9: full bandwidth allocation in 10 MHz for MBSFN ABS p. 4531
D.1.10	OCNG FDD pattern 10: outer resource blocks allocation in 10 MHz with user data in every SF (without MBSFN) p. 4531
D.1.11	OCNG FDD pattern 11: outer resource blocks allocation in 20 MHz p. 4532
D.1.12	OCNG FDD pattern 12: full bandwidth allocation in 20 MHz p. 4532
D.1.13	OCNG FDD pattern 13: outer resource blocks allocation in 20 MHz (without MBSFN) p. 4533
D.1.14	OCNG FDD pattern 14: full bandwidth allocation in 20 MHz (without MBSFN) p. 4533
D.1.15	OCNG FDD pattern 15: outer resource blocks allocation in 5 MHz p. 4534
D.1.16	OCNG FDD pattern 16: full bandwidth allocation in 5 MHz p. 4534
D.1.17	OCNG FDD pattern 17: outer resource blocks allocation in 20 MHz with user data in every subframe (without MBSFN) p. 4535
D.1.18	OCNG FDD pattern 18: outer resource blocks allocation in 5 MHz (without MBSFN) p. 4535
D.1.19	OCNG FDD pattern 19: full bandwidth allocation in 5 MHz (without MBSFN) p. 4536
D.1.20	OCNG FDD pattern 20: outer resource blocks allocation in 5 MHz with user data in every subframe (without MBSFN) p. 4536
D.1.21	OCNG FDD pattern 21: Generic resource blocks allocation (without MBSFN) p. 4537

D.2

OCNG Patterns for TDD p. 4537

D.2.0	- p. 4537
D.2.1	OCNG TDD pattern 1: outer resource blocks allocation in 10 MHz p. 4538
D.2.2	OCNG TDD pattern 2: full bandwidth allocation in 10 MHz p. 4538
D.2.3	OCNG TDD pattern 3: outer resource blocks allocation in 1.4 MHz p. 4539
D.2.4	OCNG TDD pattern 4: full bandwidth allocation in 1.4 MHz p. 4539
D.2.5	OCNG TDD pattern 5: outer resource blocks allocation in 10 MHz for MBSFN ABS p. 4540
D.2.6	OCNG TDD pattern 6: full bandwidth allocation in 10 MHz for MBSFN ABS p. 4541
D.2.7	OCNG TDD pattern 7: outer resource blocks allocation in 20 MHz p. 4542
D.2.8	OCNG TDD pattern 8: full bandwidth allocation in 20 MHz p. 4543
D.2.9	OCNG TDD pattern 9: outer resource blocks allocation in 5 MHz p. 4543
D.2.10	OCNG TDD pattern 10: full bandwidth allocation in 5 MHz p. 4544
D.2.11	OCNG TDD pattern 11: Generic resource blocks allocation (without MBSFN) p. 4545

D.3

OCNG Patterns for Narrowband IoT p. 4545

D.3.0	- p. 4545
D.3.1	Narrowband IoT OCNG FDD pattern 1: In-band NB-IoT in 10 MHz EUTRAN cell p. 4546
D.3.2	Narrowband IoT OCNG FDD pattern 2: guard band NB-IoT in 10 MHz EUTRAN cell p. 4547
D.3.3	Narrowband IoT OCNG FDD pattern 3: standalone NB-IoT p. 4548
D.3.4	Narrowband IoT OCNG FDD pattern 4: In-band NB-IoT in 5 MHz EUTRAN cell p. 4549
D.3.5	Narrowband IoT OCNG FDD pattern 5: guard band NB-IoT in 5 MHz EUTRAN cell p. 4550
D.3.6	Narrowband IoT OCNG TDD pattern 1: In-band NB-IoT in 10 MHz EUTRAN cell p. 4551
D.3.7	Narrowband IoT OCNG TDD pattern 2: guard band NB-IoT in 10 MHz EUTRAN cell p. 4552
D.3.8	Narrowband IoT OCNG TDD pattern 3: standalone NB-IoT p. 4553

D.4

OCNG Patterns for V2X sidelink p. 4553

D.4.0	- p. 4553
D.4.1	V2X sidelink OCNG TDD pattern 1: outer resource blocks allocation in 10 MHz p. 4554
D.4.2	V2X sidelink OCNG TDD pattern 2: outer resource blocks allocation in 10 MHz p. 4554

(Normative) Cell configuration mapping p. 4555

(Normative) Measurement uncertainties and Test Tolerances p. 4608

F.0

General p. 4608

F.1

Acceptable uncertainty of Test System (normative) p. 4608

F.1.1	Measurement of test environments p. 4608
F.1.2	Measurement of RRM requirements p. 4608

F.2

Interpretation of measurement results (normative) p. 4709

F.3

Test Tolerance and Derivation of Test Requirements (informative) p. 4709

F.3.0	General p. 4709
F.3.1	Measurement of test environments p. 4709
F.3.2	Measurement of RRM requirements p. 4709

(Normative) Statistical Testing p. 4852

G.1

General p. 4852

G.2

Statistical testing of delay and UE measurement performance in RRM tests p. 4852

G.2.1	General p. 4852
G.2.2	Design of the test p. 4852
G.2.3	Numerical definition of the pass fail limits p. 4852
G.2.4	Pass fail decision rules p. 4853
G.2.5	Void p. …
G.2.6	Test conditions for delay tests and UE measurement performance p. 4854

G.X

Theory to derive the numbers in Table G.2.3-1 (informative) p. 4854

(Normative) Default Message Contents p. 4855

H.1

Common contents of system information messages exceptions p. 4855

H.2

Common contents of system information blocks exceptions p. 4855

H.2.1	System information blocks message contents exceptions for E-UTRAN intra frequency cell re-selection p. 4855
H.2.2	System information blocks message contents exceptions for E-UTRAN inter frequency cell re-selection p. 4856
H.2.3	System information blocks message contents exceptions for E-UTRAN inter-RAT cell re-selection p. 4857
H.2.4	System information blocks message contents exceptions for E-UTRAN radio link monitoring (RLM) p. 4862
H.2.5	System information blocks message contents exceptions for RRC Re-establishment p. 4863
H.2.6	System information block messages and information elements contents exceptions for E-UTRAN Random Access p. 4864
H.2.7	System information blocks message contents exceptions for eICIC/feICIC p. 4865
H.2.8	System information blocks message contents exceptions for eMTC p. 4865
H.2.9	System information blocks message contents exceptions for HD-FDD radio link monitoring (RLM) for UE Category NB1 p. 4866

H.3

Default RRC messages and information elements contents exceptions p. 4866

H.3.1	RRC messages and information elements contents exceptions for E-UTRAN measurement configuration p. 4867
H.3.2	RRC messages and information elements contents exceptions for E-UTRAN cell re-selection and handover p. 4877
H.3.3	RRC messages and information elements contents exceptions for E-UTRAN inter-RAT handover p. 4878
H.3.4	RRC messages and information elements exceptions for E-UTRAN UE transmit timing accuracy and UE timing advance adjustment accuracy p. 4879
H.3.5	RRC messages and information elements contents exceptions for E-UTRAN RSRP and RSRQ Accuracy p. 4880
H.3.6	RRC messages and information elements contents exceptions for E-UTRAN inter frequency handover and E-UTRAN intra frequency cell search p. 4884
H.3.7	RRC messages and information elements contents exceptions for E-UTRAN inter frequency and E-UTRAN inter-RAT cell search when DRX is used p. 4885
H.3.8	RRC messages and information elements contents exceptions for E-UTRAN CSI-RSRP Accuracy p. 4886
H.3.9	RRC messages and information elements contents exceptions for RSSI Accuracy p. 4890

H.4

Default RRC messages and information elements contents exceptions for Carrier Aggregation p. 4891

H.4.1	RRC messages and information elements contents exceptions for E-UTRAN measurement configuration for CA p. 4891
H.4.2	RRC messages and information elements contents exceptions for E-UTRAN RSRP and RSRQ Accuracy for CA p. 4896

H.5

Default RRC messages and information elements contents exceptions for FeICIC p. 4899

H.5.1	RRC messages and information elements contents exceptions for E-UTRAN measurement configuration for FeICIC p. 4900
H.5.2	RRC messages and information elements contents exceptions for E-UTRAN RSRP and RSRQ Accuracy for FeICIC p. 4901

H.6

Default RRC messages and information elements contents exceptions for Proximity based services p. 4902

H.6.1

RRC messages and information elements contents exceptions for E-UTRAN measurement configuration for Proximity based services p. 4902

H.6.1.1	Reference resource pool configurations for ProSe Direct Discovery p. 4902
H.6.1.2	Reference resource pool configurations for ProSe Direct Communication p. 4904

H.7

Default RRC messages and information elements contents exceptions for eMTC p. 4906

H.7.1

RRC messages and information elements contents exceptions for eMTC p. 4906

(Normative) Conditions for RRM requirements applicability for operating bands p. 4908

I.1

Conditions for E-UTRAN RRC_IDLE state mobility p. 4908

I.1.1	Conditions for measurements of intra-frequency E-UTRAN cells for cell re-selection p. 4908
I.1.2	Conditions for measurements of inter-frequency E-UTRAN cells for cell re-selection p. 4908
I.1.3	Void p. …
I.1.4	Conditions for measurements of intra-frequency NB-IoT cells for cell re-selection for UE Category NB1 p. 4908
I.1.5	Conditions for measurements of inter-frequency NB-IoT cells for cell re-selection for UE Category NB1 p. 4909

I.2

Conditions for UE Measurements Procedures in RRC_CONNECTED State p. 4910

I.2.1

Conditions for E-UTRAN intra-frequency measurements p. 4910

I.2.2

Conditions for E-UTRAN intra-frequency measurements with autonomous gaps p. 4910

I.2.3

Conditions for E-UTRAN inter-frequency measurements p. 4910

I.2.4

Conditions for E-UTRAN inter-frequency measurements with autonomous gaps p. 4911

I.2.5

Void p. …

I.2.6

Void p. …

I.2.7

Conditions for Measurements of the secondary component carrier with deactivated SCell p. 4911

I.2.8

Conditions for E-UTRAN Intra-Frequency Measurements under Time Domain Measurement Resource Restriction p. 4912

I.2.9

Conditions for E-UTRAN Intra-Frequency Measurements under Time Domain Measurement Resource Restriction with CRS Assistance Information p. 4912

I.2.10

Conditions for E-UTRAN intra-frequency discovery signal measurements p. 4913

I.2.11

Conditions for E-UTRAN inter-frequency discovery signal measurements p. 4913

I.2.11.1	Conditions for E-UTRAN inter-frequency CRS-based measurements p. 4913
I.2.11.2	Conditions for E-UTRAN inter-frequency CSI-RS based measurements p. 4914

I.2.12_14

Void p. …

I.2.15

Conditions for NB-IoT intra-frequency measurements by UE Category NB1 p. 4914

I.2.16

Conditions for NB-IoT intra-frequency RSTD measurements by UE Category NB1 p. 4915

I.2.17

Conditions for NB-IoT inter-frequency RSTD measurements by UE Category NB1 p. 4916

I.3

Conditions for measurements performance requirements for UE p. 4917

I.3.1

Conditions for intra-frequency RSRP and RSRQ Accuracy Requirements p. 4917

I.3.2

Void p. …

I.3.3

Conditions for inter-frequency RSRP and RSRQ Accuracy Requirements p. 4917

I.3.4

Conditions for inter-frequency relative RSRP and RSRQ Accuracy Requirements p. 4917

I.3.5_7

Void p. …

I.3.8

Conditions for Intra-Frequency Relative RSRP Accuracy Requirements p. 4917

I.3.9

Conditions for Intra-Frequency Absolute RSRP and RSRQ Accuracy Requirements under Time Domain Measurement Resource Restriction p. 4918

I.3.10

Conditions for Intra-Frequency Relative RSRP Accuracy Requirements under Time Domain Measurement Resource Restriction p. 4918

I.3.11

Conditions for Intra-Frequency Absolute RSRP and RSRQ Accuracy Requirements under Time Domain Measurement Resource Restriction with CRS Assistance Information p. 4918

I.3.12

Conditions for Intra-Frequency Relative RSRP Accuracy Requirements under Time Domain Measurement Resource Restriction with CRS Assistance Information p. 4918

I.3.13

Void p. …

I.3.14

Conditions for Intra-Frequency Absolute Discovery Signal Measurement Accuracy Requirements p. 4919

I.3.14.1	Conditions for Intra-frequency CRS-based measurements p. 4919
I.3.14.2	Conditions for Intra-frequency CSI-RS-based measurements p. 4919

I.3.15

Conditions for Intra-Frequency Relative Discovery Signal Measurement Accuracy Requirements p. 4919

I.3.15.1	Conditions for Intra-frequency CRS-based measurements p. 4919
I.3.15.2	Conditions for Intra-frequency CSI-RS-based measurements p. 4919

I.3.16

Conditions for Inter-Frequency Absolute Discovery Signal Measurement Accuracy Requirements p. 4920

I.3.16.1	Conditions for Inter-frequency CRS-based measurements p. 4920
I.3.16.2	Conditions for Inter-frequency CSI-RS-based measurements p. 4920

I.3.17

Conditions for Inter-Frequency Relative Discovery Signal Measurement Accuracy Requirements p. 4920

I.3.17.1	Conditions for Inter-frequency CRS-based measurements p. 4920
I.3.17.2	Conditions for Inter-frequency CSI-RS-based measurements p. 4920

I.3.18_24

Void p. …

I.3.25

Conditions for NB-IoT intra-frequency Absolute NRSRP and NRSRQ Accuracy Requirements for UE Category NB1 p. 4921

I.3.26

Conditions for NB-IoT inter-frequency Absolute NRSRP and NRSRQ Accuracy Requirements for UE Category NB1 p. 4921

I.4

RRM Requirements Exceptions p. 4921

I.4.1

General p. 4921

I.4.2

Receiver sensitivity relaxation for UE supporting CA p. 4921

I.4.3

Receiver sensitivity relaxation for UE configured with CA p. 4922

I.4.3.1	Inter-band carrier aggregation p. 4922
I.4.3.2	Intra-band non-contiguous carrier aggregation p. 4922
I.4.3.3	Inter-band carrier aggregation with operating bands without uplink band p. 4922

I.5

Void p. …

I.6

Conditions for V2X p. 4923

I.6.1	Void p. …
I.6.2	Conditions for Absolute S-RSRP Accuracy Requirements p. 4923
I.6.3	Conditions for Relative S-RSRP Accuracy Requirements p. 4923
I.6.4	Conditions for Selection/Reselection to Intra-frequency SyncRef UE p. 4923
I.6.5	Conditions for Absolute PSSCH-RSRP Accuracy Requirements p. 4924

I.7

Conditions for sTTI and 1ms-TTI with 3 Subframe HARQ Processing p. 4924

I.7.1

Conditions for Maximum Timing Difference Between Uplink and Downlink Carriers in Carrier Aggregation p. 4924

I.8

High level test procedure for SAN RRM tests p. 4925

Handling requirements and tests for different releases and UE capabilities p. 4926

J.1

General considerations p. 4926

J.2

Concrete scenarios p. 4926

J.2.1	Tests for minimum requirements varying between releases, without introduction of new features p. 4926
J.2.2	Void p. …

Change history p. 4927

TS 36.521-3 E-UTRA — UE Conformance Specification Radio Transmission and Reception Part 3: Radio Resource Management (RRM) Conformance Testing

full Table of Contents for TS 36.521-3 Word version: 18.10.0

TS 36.521-3
E-UTRA — UE Conformance Specification
Radio Transmission and Reception
Part 3: Radio Resource Management (RRM) Conformance Testing