Tech-invite  3GPPspace  IETFspace
◀  ▶  21  22  23  24  25  26  27  28  29  31  32  33  34  35  36  37  38  4‑5x
Top   in Index   Prev   Next

TS 36.521-1
E-UTRA — UE Conformance Specification
Radio Transmission and Reception
Part 1: Conformance Testing

3GPP‑Page   ETSI‑search
V18.10.0 (PDF)  2025/09  6724 p.
V17.7.0  2023/06  177 p.
V16.11.0  2021/12  172 p.
V15.6.0  2020/03  156 p.
V14.6.0  2018/03  131 p.
V13.4.0  2017/03  101 p.
V12.9.0  2016/03  81 p.
V11.4.0  2014/03  48 p.
V10.6.0  2013/06  32 p.
V9.8.0  2012/03  25 p.
V8.6.0  2010/06  18 p.
Rapporteur:
Miss Fernandez, Flores

full Table of Contents for  TS 36.521-1  Word version:  18.10.0

1Scope  p. 125
2References  p. 126
3Definitions, symbols and abbreviations  p. 128
3.1Definitions  p. 128
3.2Symbols  p. 130
3.3Abbreviations  p. 132
4General  p. 135
4.1Categorization of test requirements in CA, UL-MIMO, ProSe, Dual Connectivity, UE category 0, UE category M1, UE category M2, UE category 1bis, UE category NB1, UE category NB2, V2X Communication  p. 136
4.2RF requirements in later releases  p. 137
5Frequency bands and channel arrangement  p. 138
5.1General  p. 138
5.2Operating bands  p. 138
5.2AOperating bands for CA  p. 140
5.2BOperating bands for UL-MIMO  p. 156
5.2COperating bands for Dual Connectivity  p. 156
5.2DOperating bands for ProSe  p. 156
5.2EOperating bands for UE category 0, UE category M1, M2 and UE category 1bis  p. 157
5.2FOperating bands for UE category NB1 and NB2  p. 157
5.2GOperating bands for V2X Communication  p. 158
5.3TX-RX frequency separation  p. 159
5.3ATX-RX frequency separation for CA  p. 160
5.3FTX-RX frequency separation for category NB1 and NB2  p. 160
5.4Channel arrangement  p. 160
5.4.1Channel spacing  p. 160
5.4.1AChannel spacing for CA  p. 160
5.4.1FChannel spacing for UE category NB1 and NB2  p. 160
5.4.2Channel bandwidth  p. 160
5.4.2.1Channel bandwidths per operating band  p. 161
5.4.2AChannel bandwidth for CA  p. 163
5.4.2A.1Channel bandwidths per operating band for CA  p. 165
5.4.2BChannel bandwidth for UL-MIMO  p. 258
5.4.2B.1Channel bandwidths per operating band for UL- MIMO  p. 258
5.4.2CChannel bandwidth for Dual Connectivity  p. 258
5.4.2DChannel bandwidth for ProSe  p. 258
5.4.2D.1Channel bandwidths per operating band for ProSe  p. 258
5.4.2FChannel bandwidth for category NB1 and category NB2  p. 259
5.4.2GChannel bandwidth for V2X Communication  p. 259
5.4.2G.1Channel bandwidths per operating band for V2X Communication  p. 259
5.4.3Channel raster  p. 261
5.4.3AChannel raster for CA  p. 261
5.4.3FChannel raster for UE category NB1 and NB2  p. 261
5.4.4Carrier frequency and EARFCN  p. 261
5.4.4FCarrier frequency and EARFCN for category NB1 and NB2  p. 263
5.5-  p. 263
5.5HOperating bands for LTE based 5G terrestrial broadcast  p. 263
5.6-  p. 264
5.6HPMCH bandwidth for LTE based 5G terrestrial broadcast  p. 264
5.6H.1PMCH bandwidths per operating band for LTE based 5G terrestrial broadcast  p. 264
5.7-  p. 264
5.7.1-  p. 264
5.7.1HChannel spacing for LTE based 5G terrestrial broadcast  p. 264
5.7.2-  p. 265
5.7.3-  p. 265
5.7.3HCarrier frequency and EARFCN for LTE based 5G terrestrial broadcast  p. 265
6Transmitter Characteristics  p. 266
6.1General  p. 266
6.2Transmit power  p. 267
6.2.1Void  p. …
6.2.2UE Maximum Output Power  p. 267
6.2.2.1Test purpose  p. 267
6.2.2.2Test applicability  p. 267
6.2.2.3Minimum conformance requirements  p. 267
6.2.2.4Test description  p. 270
6.2.2.4.1Initial condition  p. 270
6.2.2.4.2Test procedure  p. 271
6.2.2.4.3Message contents  p. 272
6.2.2.5Test requirements  p. 272
6.2.2_1Maximum Output Power for HPUE  p. 275
6.2.2_1.1Test purpose  p. 275
6.2.2_1.2Test applicability  p. 275
6.2.2_1.3Minimum conformance requirements  p. 275
6.2.2_1.4Test description  p. 276
6.2.2_1.5Test requirements  p. 277
6.2.2AUE Maximum Output Power for CA  p. 278
6.2.2A.0Minimum conformance requirements  p. 278
6.2.2A.1UE Maximum Output Power for CA (intra-band contiguous DL CA and UL CA)  p. 281
6.2.2A.1.1Test purpose  p. 281
6.2.2A.1.2Test applicability  p. 281
6.2.2A.1.3Minimum conformance requirements  p. 281
6.2.2A.1.4Test description  p. 282
6.2.2A.1.5Test Requirements  p. 284
6.2.2A.1_3UE Maximum Output Power for CA and HPUE (intra-band contiguous DL CA and UL CA)  p. 285
6.2.2A.1_3.1Test purpose  p. 285
6.2.2A.1_3.2Test applicability  p. 285
6.2.2A.1_3.3Minimum conformance requirements  p. 285
6.2.2A.1_3.4Test description  p. 285
6.2.2A.1_3.5Test Requirements  p. 285
6.2.2A.2UE Maximum Output Power for CA (inter-band DL CA and UL CA)  p. 285
6.2.2A.2.1Test purpose  p. 285
6.2.2A.2.2Test applicability  p. 286
6.2.2A.2.3Minimum conformance requirements  p. 286
6.2.2A.2.4Test description  p. 286
6.2.2A.2.5Test Requirements  p. 289
6.2.2A.3UE Maximum Output Power for CA (intra-band non-contiguous DL CA and UL CA)  p. 291
6.2.2A.4UE Maximum Output Power for CA (3UL CA)  p. 291
6.2.2A.4.1Test purpose  p. 291
6.2.2A.4.2Test applicability  p. 291
6.2.2A.4.3Minimum conformance requirements  p. 291
6.2.2A.4.4Test description  p. 292
6.2.2A.4.5Test Requirements  p. 296
6.2.2A.4.1aVoid  p. …
6.2.2A.4.2aVoid  p. …
6.2.2A.5UE Maximum Output Power for CA (4UL CA)  p. 297
6.2.2A.5.1Test purpose  p. 297
6.2.2A.5.2Test applicability  p. 297
6.2.2A.5.3Minimum conformance requirements  p. 297
6.2.2A.5.4Test description  p. 298
6.2.2A.5.5Test Requirements  p. 300
6.2.2BUE Maximum Output Power for UL-MIMO  p. 301
6.2.2B.1Test purpose  p. 301
6.2.2B.2Test applicability  p. 301
6.2.2B.3Minimum conformance requirements  p. 301
6.2.2B.4Test description  p. 304
6.2.2B.4.1Initial condition  p. 304
6.2.2B.4.2Test procedure  p. 305
6.2.2B.4.3Message contents  p. 306
6.2.2B.5Test requirements  p. 306
6.2.2B_1HPUE Maximum Output Power for UL-MIMO  p. 308
6.2.2B_1.1Test purpose  p. 308
6.2.2B_1.2Test applicability  p. 308
6.2.2B_1.3Minimum conformance requirements  p. 308
6.2.2B_1.4Test description  p. 309
6.2.2B_1.5Test requirements  p. 309
6.2.2CVoid  p. …
6.2.2DUE Maximum Output Power for ProSe  p. 310
6.2.2D.0Minimum conformance requirements  p. 310
6.2.2D.1UE Maximum Output Power for ProSe Discovery  p. 310
6.2.2D.1.1Test purpose  p. 310
6.2.2D.1.2Test applicability  p. 310
6.2.2D.1.3Minimum Conformance requirements  p. 311
6.2.2D.1.4Test description  p. 311
6.2.2D.1.5Test requirements  p. 312
6.2.2D.2UE Maximum Output Power for ProSe Direct Communication  p. 312
6.2.2D.2.1Test purpose  p. 312
6.2.2D.2.2Test applicability  p. 312
6.2.2D.2.3Minimum conformance requirements  p. 313
6.2.2D.2.4Test description  p. 313
6.2.2EUE Maximum Output Power for UE category 0  p. 313
6.2.2E.1Test purpose  p. 313
6.2.2E.2Test applicability  p. 313
6.2.2E.3Minimum conformance requirements  p. 313
6.2.2E.4Test description  p. 313
6.2.2E.4.3Message contents  p. 314
6.2.2E.5Test requirements  p. 314
6.2.2EAUE Maximum Output Power for UE category M1  p. 316
6.2.2EA.1Test purpose  p. 316
6.2.2EA.2Test applicability  p. 316
6.2.2EA.3Minimum conformance requirements  p. 316
6.2.2EA.4Test description  p. 317
6.2.2EA.4.3Message contents  p. 319
6.2.2EA.5Test requirements  p. 319
6.2.2EBUE Maximum Output Power for UE category 1bis  p. 320
6.2.2EB.1Test purpose  p. 320
6.2.2EB.2Test applicability  p. 320
6.2.2EB.3Minimum conformance requirements  p. 321
6.2.2EB.4Test description  p. 321
6.2.2EB.4.1Initial conditions  p. 321
6.2.2EB.4.2Test procedure  p. 321
6.2.2EB.4.3Message contents  p. 321
6.2.2EB.5Test requirement  p. 322
6.2.2ECUE Maximum Output Power for UE category M2  p. 322
6.2.2EC.1Test purpose  p. 322
6.2.2EC.2Test applicability  p. 322
6.2.2EC.3Minimum conformance requirements  p. 322
6.2.2EC.4Test description  p. 322
6.2.2EC.4.1Initial condition  p. 322
6.2.2EC.4.2Test procedure  p. 323
6.2.2EC.4.3Message contents  p. 323
6.2.2EC.5Test requirements  p. 324
6.2.2FUE Maximum Output Power for category NB1 and NB2  p. 324
6.2.2F.4Test description  p. 325
6.2.2F.4.1Initial condition  p. 325
6.2.2F.4.2Test procedure  p. 326
6.2.2F.4.3Message contents  p. 326
6.2.2F.5Test requirements  p. 326
6.2.2FAUE Maximum Output Power for category NB1 and NB2/Power Class 6  p. 327
6.2.2FA.4Test description  p. 328
6.2.2FA.5Test requirements  p. 328
6.2.2GUE Maximum Output Power for V2X Communication  p. 329
6.2.2G.1UE Maximum Output Power for V2X Communication / Non-concurrent with E-UTRA uplink transmission  p. 329
6.2.2G.1.1Test purpose  p. 329
6.2.2G.1.2Test applicability  p. 329
6.2.2G.1.3Minimum conformance requirements  p. 329
6.2.2G.1.4Test description  p. 330
6.2.2G.1.4.1Initial conditions  p. 330
6.2.2G.1.4.2Test procedure  p. 330
6.2.2G.1.4.3Message contents  p. 330
6.2.2G.1.5Test requirements  p. 330
6.2.2G.2UE Maximum Output Power for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmission  p. 331
6.2.2G.2.1Test purpose  p. 331
6.2.2G.2.2Test applicability  p. 331
6.2.2G.2.3Minimum conformance requirements  p. 331
6.2.2G.2.4Test description  p. 331
6.2.2G.2.4.1Initial conditions  p. 331
6.2.2G.2.4.2Test procedure  p. 332
6.2.2G.2.4.3Message contents  p. 332
6.2.2G.2.5Test requirements  p. 333
6.2.2G.3UE Maximum Output Power for V2X Communication / Intra-band contiguous multi-carrier operation  p. 333
6.2.2G.3.1Test purpose  p. 333
6.2.2G.3.2Test applicability  p. 333
6.2.2G.3.3Minimum conformance requirements  p. 333
6.2.2G.3.4Test description  p. 334
6.2.2G.3.4.1Initial conditions  p. 334
6.2.2G.3.4.2Test procedure  p. 334
6.2.2G.3.4.3Message contents  p. 334
6.2.2G.3.5Test requirements  p. 335
6.2.2G.4UE Maximum Output Power for V2X Communication / Power class 2  p. 335
6.2.2G.4.1UE Maximum Output Power for V2X Communication / Power class 2 / Non-concurrent with E-UTRA uplink transmissions  p. 335
6.2.2G.4.1.1Test purpose  p. 335
6.2.2G.4.1.2Test applicability  p. 335
6.2.2G.4.1.3Minimum conformance requirements  p. 335
6.2.2G.4.1.4Test description  p. 335
6.2.2G.4.1.4.1Initial conditions  p. 335
6.2.2G.4.1.4.2Test procedure  p. 336
6.2.2G.4.1.4.3Message contents  p. 336
6.2.2G.4.1.5Test requirements  p. 336
6.2.2_sUE Maximum Output Power for subslot/slot TTI  p. 336
6.2.3Maximum Power Reduction (MPR)  p. 341
6.2.3.1Test purpose  p. 341
6.2.3.2Test applicability  p. 341
6.2.3.3Minimum conformance requirements  p. 342
6.2.3.4Test description  p. 342
6.2.3.4.1Initial condition  p. 342
6.2.3.4.2Test procedure  p. 343
6.2.3.4.3Message contents  p. 344
6.2.3.5Test requirements  p. 344
6.2.3_1Maximum Power Reduction (MPR) for HPUE  p. 347
6.2.3_1.1Test purpose  p. 347
6.2.3_1.2Test applicability  p. 348
6.2.3_1.3Minimum conformance requirements  p. 348
6.2.3_1.4Test description  p. 348
6.2.3_1.5Test requirements  p. 348
6.2.3_2Maximum Power Reduction (MPR) for Multi-Cluster PUSCH  p. 349
6.2.3_2.1Test purpose  p. 349
6.2.3_2.2Test applicability  p. 349
6.2.3_2.3Minimum conformance requirements  p. 349
6.2.3_2.4Test description  p. 350
6.2.3_2.4.1Initial condition  p. 350
6.2.3_2.4.2Test procedure  p. 351
6.2.3_2.4.3Message contents  p. 351
6.2.3_2.5Test requirements  p. 351
6.2.3_3Maximum Power Reduction (MPR) for UL 64QAM  p. 354
6.2.3_3.1Test purpose  p. 354
6.2.3_3.2Test applicability  p. 354
6.2.3_3.3Minimum conformance requirements  p. 354
6.2.3_3.4Test description  p. 354
6.2.3_3.4.1Initial condition  p. 354
6.2.3_3.4.2Test procedure  p. 355
6.2.3_3.4.3Message contents  p. 355
6.2.3_3.5Test requirements  p. 356
6.2.3_4Maximum Power Reduction (MPR) for Multi-Cluster PUSCH with UL 64QAM  p. 359
6.2.3_4.1Test purpose  p. 359
6.2.3_4.2Test applicability  p. 360
6.2.3_4.3Minimum conformance requirements  p. 360
6.2.3_4.4Test description  p. 360
6.2.3_4.4.1Initial condition  p. 360
6.2.3_4.4.2Test procedure  p. 361
6.2.3_4.4.3Message contents  p. 361
6.2.3_4.5Test requirements  p. 361
6.2.3_5Maximum Power Reduction (MPR) for UL 256QAM  p. 362
6.2.3_5.1Test purpose  p. 363
6.2.3_5.2Test applicability  p. 363
6.2.3_5.3Minimum conformance requirements  p. 363
6.2.3_5.4Test description  p. 363
6.2.3_5.4.1Initial condition  p. 363
6.2.3_5.4.2Test procedure  p. 364
6.2.3_5.4.3Message contents  p. 364
6.2.3_5.5Test requirements  p. 364
6.2.3_6Maximum Power Reduction (MPR) for Multi-Cluster PUSCH with UL 256QAM  p. 367
6.2.3_6.1Test purpose  p. 367
6.2.3_6.2Test applicability  p. 368
6.2.3_6.3Minimum conformance requirements  p. 368
6.2.3_6.4Test description  p. 368
6.2.3_6.4.1Initial condition  p. 368
6.2.3_6.4.2Test procedure  p. 369
6.2.3_6.4.3Message contents  p. 369
6.2.3_6.5Test requirements  p. 369
6.2.3AMaximum Power Reduction (MPR) for CA  p. 370
6.2.3A.1Maximum Power Reduction (MPR) for CA (intra-band contiguous DL CA and UL CA)  p. 370
6.2.3A.1.1Test purpose  p. 370
6.2.3A.1.2Test applicability  p. 371
6.2.3A.1.3Minimum conformance requirements  p. 371
6.2.3A.1.4Test description  p. 372
6.2.3A.1.5Test Requirements  p. 376
6.2.3A.1_1Maximum Power Reduction (MPR) for CA (intra-band contiguous DL CA and UL CA) for UL 64QAM  p. 382
6.2.3A.1_1.1Test purpose  p. 382
6.2.3A.1_1.2Test applicability  p. 382
6.2.3A.1_1.3Minimum conformance requirements  p. 382
6.2.3A.1_1.4Test description  p. 383
6.2.3A.1_1.5Test requirement  p. 385
6.2.3A.1_2Maximum Power Reduction (MPR) for CA (intra-band contiguous DL CA and UL CA) for UL 256QAM  p. 386
6.2.3A.1_2.1Test purpose  p. 386
6.2.3A.1_2.2Test applicability  p. 386
6.2.3A.1_2.3Minimum conformance requirements  p. 386
6.2.3A.1_2.4Test description  p. 387
6.2.3A.1_2.5Test requirement  p. 388
6.2.3A.1_3Maximum Power Reduction (MPR) for CA and HPUE (intra-band contiguous DL CA and UL CA)  p. 389
6.2.3A.1_3.1Test purpose  p. 390
6.2.3A.1_3.2Test applicability  p. 390
6.2.3A.1_3.3Minimum conformance requirements  p. 390
6.2.3A.1_3.4Test description  p. 391
6.2.3A.1_3.5Test Requirements  p. 394
6.2.3A.2Maximum Power Reduction (MPR) for CA (inter-band DL CA and UL CA)  p. 396
6.2.3A.2.1Test purpose  p. 396
6.2.3A.2.2Test applicability  p. 396
6.2.3A.2.3Minimum conformance requirements  p. 396
6.2.3A.2.4Test description  p. 396
6.2.3A.2.5Test Requirements  p. 403
6.2.3A.2_1Maximum Power Reduction (MPR) for CA (inter-band DL CA and UL CA) for UL 64QAM  p. 407
6.2.3A.2_1.1Test purpose  p. 407
6.2.3A.2_1.2Test applicability  p. 407
6.2.3A.2_1.3Minimum conformance requirements  p. 407
6.2.3A.2_1.4Test description  p. 408
6.2.3A.2_1.5Test Requirements  p. 409
6.2.3A.2_2Maximum Power Reduction (MPR) for CA (inter-band DL CA and UL CA) for UL 256QAM  p. 411
6.2.3A.2_2.1Test purpose  p. 411
6.2.3A.2_2.2Test applicability  p. 411
6.2.3A.2_2.3Minimum conformance requirements  p. 411
6.2.3A.2_2.4Test description  p. 411
6.2.3A.2_2.5Test Requirement  p. 413
6.2.3A.3Maximum Power Reduction (MPR) for CA (intra-band non-contiguous DL CA and UL CA)  p. 414
6.2.3A.3.1Test purpose  p. 414
6.2.3A.3.2Test applicability  p. 414
6.2.3A.3.3Minimum conformance requirements  p. 414
6.2.3A.3.4Test description  p. 415
6.2.3A.3.5Test Requirements  p. 416
6.2.3A.3_1Maximum Power Reduction (MPR) for CA (intra-band non-contiguous DL CA and UL CA) for UL 64QAM  p. 417
6.2.3A.3_1.1Test purpose  p. 417
6.2.3A.3_1.2Test applicability  p. 417
6.2.3A.3_1.3Minimum conformance requirements  p. 417
6.2.3A.3_1.4Test description  p. 417
6.2.3A.3_1.5Test Requirements  p. 419
6.2.3A.3_2Maximum Power Reduction (MPR) for CA (intra-band non-contiguous DL CA and UL CA) for UL 256QAM  p. 419
6.2.3A.3_2.1Test purpose  p. 419
6.2.3A.3_2.2Test applicability  p. 419
6.2.3A.3_2.3Minimum conformance requirements  p. 419
6.2.3A.3_2.4Test description  p. 419
6.2.3A.3_2.5Test Requirements  p. 420
6.2.3A.4Maximum Power Reduction (MPR) for CA (3UL CA)  p. 420
6.2.3A.4.1Test purpose  p. 420
6.2.3A.4.2Test applicability  p. 421
6.2.3A.4.3Minimum conformance requirements  p. 421
6.2.3A.4.4Test description  p. 423
6.2.3A.4.4.1Initial conditions  p. 423
6.2.3A.4.5Test Requirements  p. 431
6.2.3A.5Maximum Power Reduction (MPR) for CA (4UL CA)  p. 439
6.2.3A.5.1Test purpose  p. 440
6.2.3A.5.2Test applicability  p. 440
6.2.3A.5.3Minimum conformance requirements  p. 440
6.2.3A.5.4Test description  p. 441
6.2.3A.5.5Test Requirements  p. 443
6.2.3BMaximum Power Reduction (MPR) for UL-MIMO  p. 444
6.2.3B.1Test purpose  p. 444
6.2.3B.2Test applicability  p. 444
6.2.3B.3Minimum conformance requirements  p. 444
6.2.3B.4Test description  p. 444
6.2.3B.4.1Initial condition  p. 444
6.2.3B.4.2Test procedure  p. 445
6.2.3B.4.3Message contents  p. 446
6.2.3B.5Test requirements  p. 446
6.2.3DUE Maximum Output Power for ProSe  p. 450
6.2.3D.0Minimum conformance requirements  p. 450
6.2.3D.1Maximum Power Reduction (MPR) for ProSe Discovery  p. 450
6.2.3D.1.1Test purpose  p. 451
6.2.3D.1.2Test applicability  p. 451
6.2.3D.1.3Minimum conformance requirements  p. 451
6.2.3D.1.4Test description  p. 451
6.2.3D.1.4.1Initial condition  p. 451
6.2.3D.1.4.2Test procedure  p. 452
6.2.3D.1.4.3Message contents  p. 452
6.2.3D.1.5Test requirements  p. 453
6.2.3D.2Maximum Power Reduction (MPR) ProSe Direct Communication  p. 455
6.2.3D.2.1Test purpose  p. 455
6.2.3D.2.2Test applicability  p. 455
6.2.3D.2.3Minimum conformance requirements  p. 455
6.2.3D.2.4Test description  p. 455
6.2.3D.2.4.1Initial conditions  p. 455
6.2.3D.2.4.2Test procedure  p. 455
6.2.3D.2.4.3Message contents  p. 455
6.2.3D.2.5Test requirements  p. 455
6.2.3EMaximum Power Reduction (MPR) for UE category 0  p. 455
6.2.3E.1Test purpose  p. 455
6.2.3E.2Test applicability  p. 455
6.2.3E.3Minimum conformance requirements  p. 455
6.2.3E.4Test description  p. 456
6.2.3E.4.1Initial condition  p. 456
6.2.3E.4.2Test procedure  p. 456
6.2.3E.4.3Message contents  p. 456
6.2.3E.5Test requirements  p. 456
6.2.3EAMaximum Power Reduction (MPR) for UE category M1  p. 457
6.2.3EA.1Test purpose  p. 457
6.2.3EA.2Test applicability  p. 457
6.2.3EA.3Minimum conformance requirements  p. 457
6.2.3EA.4Test description  p. 458
6.2.3EA.4.1Initial condition  p. 458
6.2.3EA.4.2Test procedure  p. 460
6.2.3EA.4.3Message contents  p. 460
6.2.3EA.5Test requirements  p. 461
6.2.3EBMaximum Power Reduction (MPR) for UE category 1bis  p. 467
6.2.3EB.1Test purpose  p. 467
6.2.3EB.2Test applicability  p. 467
6.2.3EB.3Minimum conformance requirements  p. 467
6.2.3EB.4Test description  p. 468
6.2.3EB.4.1Initial conditions  p. 468
6.2.3EB.4.2Test procedure  p. 468
6.2.3EB.4.3Message contents  p. 468
6.2.3EB.5Test requirement  p. 468
6.2.3ECMaximum Power Reduction (MPR) for UE category M2  p. 469
6.2.3EC.1Test purpose  p. 469
6.2.3EC.2Test applicability  p. 470
6.2.3EC.3Minimum conformance requirements  p. 470
6.2.3EC.4Test description  p. 471
6.2.3EC.4.1Initial condition  p. 471
6.2.3EC.4.2Test procedure  p. 476
6.2.3EC.4.3Message contents  p. 476
6.2.3EC.5Test requirements  p. 476
6.2.3FMaximum Power Reduction (MPR) for category NB1 and NB2  p. 485
6.2.3F.4Test description  p. 486
6.2.3F.4.1Initial condition  p. 486
6.2.3F.4.2Test procedure  p. 487
6.2.3F.4.3Message contents  p. 487
6.2.3F.5Test requirements  p. 487
6.2.3FAMaximum Power Reduction (MPR) for category NB1 and NB2/Power Class 6  p. 488
6.2.3FA.4Test description  p. 489
6.2.3FA.5Test requirements  p. 489
6.2.3GMaximum Power Reduction (MPR) for V2X communication  p. 490
6.2.3G.1Maximum Power Reduction (MPR) for V2X Communication / Power class 3  p. 490
6.2.3G.1.1Maximum Power Reduction (MPR) for V2X Communication / Power class 3 / Contiguous allocation of PSCCH and PSSCH / Non-concurrent with E-UTRA uplink transmissions  p. 490
6.2.3G.1.2Maximum Power Reduction (MPR) for V2X Communication / Power class 3 / Non-contiguous allocation of PSCCH and PSSCH / Non-concurrent with E-UTRA uplink transmissions  p. 492
6.2.3G.1.2.2Test applicability  p. 492
6.2.3G.1.2.3Minimum conformance requirements  p. 492
6.2.3G.1.2.4Test description  p. 492
6.2.3G.1.2.4.1Initial conditions  p. 492
6.2.3G.1.2.4.2Test procedure  p. 493
6.2.3G.1.2.4.3Message contents  p. 493
6.2.3G.1.2.5Test requirements  p. 494
6.2.3G.1.3Maximum Power Reduction (MPR) for V2X Communication / Power class 3 / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmission  p. 494
6.2.3G.1.3.1Test purpose  p. 494
6.2.3G.1.3.2Test applicability  p. 494
6.2.3G.1.3.3Minimum conformance requirements  p. 494
6.2.3G.1.3.4Test description  p. 495
6.2.3G.1.3.4.1Initial conditions  p. 495
6.2.3G.1.3.4.2Test procedure  p. 496
6.2.3G.1.3.4.3Message contents  p. 496
6.2.3G.1.3.5Test requirement  p. 496
6.2.3G.1.4Maximum Power Reduction (MPR) for V2X Communication / Power class 3 / Intra-band contiguous multi-carrier operation  p. 497
6.2.3G.1.4.1Test purpose  p. 497
6.2.3G.1.4.2Test applicability  p. 497
6.2.3G.1.4.3Minimum conformance requirements  p. 497
6.2.3G.1.4.4Test description  p. 497
6.2.3G.1.4.4.1Initial conditions  p. 497
6.2.3G.1.4.4.3Message contents  p. 498
6.2.3G.1.4.5Test requirement  p. 498
6.2.3G.2Maximum Power Reduction (MPR) for V2X Communication / Power class 2  p. 499
6.2.3G.2.1Maximum Power Reduction (MPR) for V2X Communication / Power class 2 / Contiguous allocation of PSCCH and PSSCH / Non-concurrent with E-UTRA uplink transmissions  p. 499
6.2.3G.2.1.1Test purpose  p. 499
6.2.3G.2.1.2Test applicability  p. 499
6.2.3G.2.1.3Minimum conformance requirements  p. 499
6.2.3G.2.1.4.2Test procedure  p. 500
6.2.3G.2.1.5Test Requirements  p. 501
6.2.3G.2.2Maximum Power Reduction (MPR) for V2X Communication / Power class 2 / Non-contiguous allocation of PSCCH and PSSCH / Non-concurrent with E-UTRA uplink transmissions  p. 501
6.2.3G.2.2.1Test purpose  p. 501
6.2.3G.2.2.2Test applicability  p. 501
6.2.3G.2.2.3Minimum conformance requirements  p. 501
6.2.3G.2.2.4Test description  p. 502
6.2.3G.2.2.4.1Initial conditions  p. 502
6.2.3G.2.2.4.2Test procedure  p. 502
6.2.3G.2.2.4.3Message contents  p. 503
6.2.3G.2.2.5Test requirement  p. 503
6.2.3_sUE Maximum Power Reduction (MPR) for subslot/slot TTI  p. 503
6.2.4Additional Maximum Power Reduction (A-MPR)  p. 506
6.2.4.1Test purpose  p. 506
6.2.4.2Test applicability  p. 506
6.2.4.3Minimum conformance requirements  p. 507
6.2.4.4Test description  p. 522
6.2.4.4.1Initial condition  p. 522
6.2.4.4.2Test procedure  p. 562
6.2.4.4.3Message contents  p. 563
6.2.4.5Test requirements  p. 570
6.2.4_1Additional Maximum Power Reduction (A-MPR) for HPUE  p. 608
6.2.4_1.2Test applicability  p. 608
6.2.4_1.3Minimum conformance requirements  p. 608
6.2.4_1.4Test description  p. 610
6.2.4_1.5Test requirements  p. 614
6.2.4_2Additional Maximum Power Reduction (A-MPR) for UL 64QAM  p. 617
6.2.4_2.1Test purpose  p. 617
6.2.4_2.2Test applicability  p. 617
6.2.4_2.3Minimum conformance requirements  p. 617
6.2.4_2.4Test description  p. 617
6.2.4_2.4.1Initial condition  p. 617
6.2.4_2.4.2Test procedure  p. 638
6.2.4_2.4.3Message contents  p. 638
6.2.4_2.5Test requirements  p. 638
6.2.4_3Additional Maximum Power Reduction (A-MPR) with PUSCH frequency hopping  p. 652
6.2.4_3.1Test purpose  p. 652
6.2.4_3.2Test applicability  p. 653
6.2.4_3.3Minimum conformance requirements  p. 653
6.2.4_3.4Test description  p. 653
6.2.4_3.5Test requirements  p. 655
6.2.4_4Additional Maximum Power Reduction (A-MPR) for UL 256QAM  p. 656
6.2.4_4.1Test purpose  p. 656
6.2.4_4.2Test applicability  p. 656
6.2.4_4.3Minimum conformance requirements  p. 656
6.2.4_4.4Test description  p. 656
6.2.4_4.4.1Initial condition  p. 656
6.2.4_4.4.2Test procedure  p. 672
6.2.4_4.4.3Message contents  p. 672
6.2.4_4.5Test requirements  p. 672
6.2.4AAdditional Maximum Power Reduction (A-MPR) for CA  p. 682
6.2.4A.1Additional Maximum Power Reduction (A-MPR) for CA (intra-band contiguous DL CA and UL CA)  p. 682
6.2.4A.1.1Test purpose  p. 682
6.2.4A.1.2Test applicability  p. 682
6.2.4A.1.3Minimum conformance requirements  p. 683
6.2.4A.1.3.5A-MPR for CA_NS_05 for CA_38C  p. 686
6.2.4A.1.3.6A-MPR for CA_NS_06 for CA_7C  p. 687
6.2.4A.1.3.7A-MPR for CA_NS_07 for CA_39C  p. 688
6.2.4A.1.3.8A-MPR for CA_NS_10  p. 688
6.2.4A.1.4Test description  p. 693
6.2.4A.1.5Test requirements  p. 699
6.2.4A.1_1Additional Maximum Power Reduction (A-MPR) for CA (intra-band contiguous DL CA and UL CA) for UL 64QAM  p. 706
6.2.4A.1_1.1Test purpose  p. 706
6.2.4A.1_1.2Test applicability  p. 706
6.2.4A.1_1.3Minimum conformance requirements  p. 707
6.2.4A.1_1.3.5A-MPR for CA_NS_05 for CA_38C  p. 710
6.2.4A.1_1.3.6A-MPR for CA_NS_06 for CA_7C  p. 711
6.2.4A.1_1.3.7A-MPR for CA_NS_07 for CA_39C  p. 712
6.2.4A.1_1.3.8A-MPR for CA_NS_08 for CA_42C  p. 713
6.2.4A.1_1.4Test description  p. 713
6.2.4A.1_1.5Test requirements  p. 718
6.2.4A.1_2Additional Maximum Power Reduction (A-MPR) for CA (intra-band contiguous DL CA and UL CA) for UL 256QAM  p. 724
6.2.4A.1_2.1Test purpose  p. 724
6.2.4A.1_2.2Test applicability  p. 724
6.2.4A.1_2.3Minimum conformance requirements  p. 725
6.2.4A.1_2.3.5A-MPR for CA_NS_05 for CA_38C  p. 728
6.2.4A.1_2.3.6A-MPR for CA_NS_06 for CA_7C  p. 729
6.2.4A.1_2.3.7A-MPR for CA_NS_07 for CA_39C  p. 730
6.2.4A.1_2.4Test description  p. 733
6.2.4A.1_2.5Test requirements  p. 739
6.2.4A.1_3Additional Maximum Power Reduction (A-MPR) for CA and HPUE (intra-band contiguous DL CA and UL CA)  p. 745
6.2.4A.1_3.1Test purpose  p. 745
6.2.4A.1_3.2Test applicability  p. 745
6.2.4A.1_3.3Minimum conformance requirements  p. 746
6.2.4A.1_3.4Test description  p. 748
6.2.4A.1_3.5Test requirements  p. 751
6.2.4A.2Additional Maximum Power Reduction (A-MPR) for CA (inter-band DL CA and UL CA)  p. 757
6.2.4A.2.1Test purpose  p. 757
6.2.4A.2.2Test applicability  p. 758
6.2.4A.2.3Minimum conformance requirements  p. 758
6.2.4A.2.4Test description  p. 758
6.2.4A.2.4.1Initial conditions  p. 758
6.2.4A.2.4.2Test procedure  p. 780
6.2.4A.2.4.3Message contents  p. 781
6.2.4A.2.5Test requirements  p. 786
6.2.4A.2_1Additional Maximum Power Reduction (A-MPR) for CA (inter-band DL CA and UL CA) for UL 64QAM  p. 797
6.2.4A.2_1.1Test purpose  p. 797
6.2.4A.2_1.2Test applicability  p. 797
6.2.4A.2_1.3Minimum conformance requirements  p. 798
6.2.4A.2_1.4Test description  p. 798
6.2.4A.2_1.4.1Initial conditions  p. 798
6.2.4A.2_1.4.2Test procedure  p. 812
6.2.4A.2_1.4.3Message contents  p. 813
6.2.4A.2_1.5Test requirements  p. 813
6.2.4A.2_2Additional Maximum Power Reduction (A-MPR) for CA (inter-band DL CA and UL CA) for UL 256QAM  p. 819
6.2.4A.2_2.1Test purpose  p. 819
6.2.4A.2_2.2Test applicability  p. 819
6.2.4A.2_2.3Minimum conformance requirements  p. 819
6.2.4A.2_2.4Test description  p. 820
6.2.4A.2_2.4.1Initial conditions  p. 820
6.2.4A.2_2.4.2Test procedure  p. 833
6.2.4A.2_2.4.3Message contents  p. 834
6.2.4A.2_2.5Test requirements  p. 834
6.2.4A.3Additional Maximum Power Reduction (A-MPR) for CA (intra-band non-contiguous DL CA and UL CA)  p. 838
6.2.4A.3.1Minimum conformance requirements  p. 838
6.2.4A.2_2aVoid  p. …
6.2.4A.4Additional Maximum Power Reduction (A-MPR) for CA (3UL CA)  p. 839
6.2.4A.4.1Test purpose  p. 839
6.2.4A.4.2Test applicability  p. 839
6.2.4A.4.3Minimum conformance requirements  p. 839
6.2.4A.4.4Test description  p. 840
6.2.4A.4.4.1Initial conditions  p. 840
6.2.4A.4.5Test Requirements  p. 844
6.2.4A.5Additional Maximum Power Reduction (A-MPR) for CA (4UL CA)  p. 845
6.2.4A.5.1Test purpose  p. 845
6.2.4A.5.2Test applicability  p. 846
6.2.4A.5.3Minimum conformance requirements  p. 846
6.2.4A.5.4Test description  p. 846
6.2.4A.5.5Test Requirements  p. 848
6.2.4BAdditional Maximum Power Reduction (A-MPR) for UL-MIMO  p. 848
6.2.4B.1Test purpose  p. 848
6.2.4B.2Test applicability  p. 848
6.2.4B.3Minimum conformance requirements  p. 848
6.2.4B.4Test description  p. 848
6.2.4B.4.1Initial condition  p. 848
6.2.4B.4.2Test procedure  p. 879
6.2.4B.4.3Message contents  p. 879
6.2.4B.5Test requirements  p. 879
6.2.4EAdditional Maximum Power Reduction (A-MPR) for UE category 0  p. 910
6.2.4E.1Test purpose  p. 910
6.2.4E.2Test applicability  p. 910
6.2.4E.3Minimum conformance requirements  p. 911
6.2.4E.4Test description  p. 911
6.2.4E.4.1Initial condition  p. 911
6.2.4E.4.2Test procedure  p. 914
6.2.4E.4.3Message contents  p. 914
6.2.4E.5Test requirements  p. 915
6.2.4EAAdditional Maximum Power Reduction (A-MPR) for UE category M1  p. 923
6.2.4EA.1Test purpose  p. 923
6.2.4EA.2Test applicability  p. 923
6.2.4EA.3Minimum conformance requirements  p. 924
6.2.4EA.4Test description  p. 927
6.2.4EA.4.1Initial condition  p. 927
6.2.4EA.4.2Test procedure  p. 943
6.2.4EA.4.3Message contents  p. 944
6.2.4EA.5Test requirements  p. 944
6.2.4EBAdditional Maximum Power Reduction (A-MPR) for UE category 1bis  p. 956
6.2.4EB.1Test purpose  p. 956
6.2.4EB.2Test applicability  p. 956
6.2.4EB.3Minimum conformance requirements  p. 956
6.2.4EB.4Test description  p. 956
6.2.4EB.4.1Initial conditions  p. 956
6.2.4EB.4.2Test procedure  p. 956
6.2.4EB.4.3Message contents  p. 956
6.2.4EB.5Test requirement  p. 956
6.2.4ECAdditional Maximum Power Reduction (A-MPR) for UE category M2  p. 957
6.2.4EC.1Test purpose  p. 957
6.2.4EC.2Test applicability  p. 958
6.2.4EC.3Minimum conformance requirements  p. 958
6.2.4EC.4Test description  p. 963
6.2.4EC.4.1Initial condition  p. 963
6.2.4EC.4.2Test procedure  p. 969
6.2.4EC.4.3Message contents  p. 969
6.2.4EC.5Test requirement  p. 969
6.2.4GAdditional Maximum Power Reduction (A-MPR) for V2X Communication  p. 974
6.2.4G.1Additional Maximum Power Reduction (A-MPR) for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 974
6.2.4G.1.1Test purpose  p. 974
6.2.4G.1.2Test applicability  p. 974
6.2.4G.1.3Minimum conformance requirements  p. 974
6.2.4G.1.4Test description  p. 976
6.2.4G.1.4.3Message contents  p. 980
6.2.4G.1.5Test Requirements  p. 981
6.2.4G.2Additional Maximum Power Reduction (A-MPR) for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions  p. 984
6.2.4G.2.1Test purpose  p. 984
6.2.4G.2.3Minimum conformance requirements  p. 985
6.2.4G.2.4.3Message contents  p. 987
6.2.4G.2.5Test Requirements  p. 988
6.2.4_sAdditional Maximum Power Reduction (A-MPR) for subslot/slot TTI  p. 988
6.2.5Configured UE transmitted Output Power  p. 993
6.2.5.1Test purpose  p. 993
6.2.5.2Test applicability  p. 993
6.2.5.3Minimum conformance requirements  p. 993
6.2.5.4Test description  p. 1024
6.2.5.4.1Initial conditions  p. 1024
6.2.5.4.2Test procedure  p. 1024
6.2.5.4.3Message contents  p. 1025
6.2.5.5Test requirement  p. 1025
6.2.5_sConfigured UE Transmitted Output Power for subslot/slot TTI  p. 1026
6.2.5_1Configured UE transmitted Output Power for HPUE  p. 1027
6.2.5_1.1Test purpose  p. 1027
6.2.5_1.2Test applicability  p. 1028
6.2.5_1.3Minimum conformance requirements  p. 1028
6.2.5_1.4Test description  p. 1028
6.2.5_1.4.1Initial conditions  p. 1028
6.2.5_1.4.2Test procedure  p. 1028
6.2.5_1.4.3Message contents  p. 1028
6.2.5_1.5Test requirement  p. 1029
6.2.5AConfigured transmitted power for CA  p. 1030
6.2.5A.1Configured UE transmitted Output Power for CA (intra-band contiguous DL CA and UL CA)  p. 1030
6.2.5A.1.1Test purpose  p. 1030
6.2.5A.1.2Test applicability  p. 1030
6.2.5A.1.3Minimum conformance requirements  p. 1030
6.2.5A.1.4Test description  p. 1032
6.2.5A.1.5Test requirement  p. 1034
6.2.5A.1_3Configured UE transmitted Output Power for CA and HPUE (intra-band contiguous DL CA and UL CA) for HPUE  p. 1035
6.2.5A.1_3.1Test purpose  p. 1035
6.2.5A.1_3.2Test applicability  p. 1035
6.2.5A.1_3.3Minimum conformance requirements  p. 1035
6.2.5A.1_3.4Test description  p. 1036
6.2.5A.1_3.5Test requirement  p. 1039
6.2.5A.2Void  p. …
6.2.5A.3Configured UE transmitted Output Power for CA (inter-band DL CA and UL CA)  p. 1039
6.2.5A.3.1Test purpose  p. 1039
6.2.5A.3.2Test applicability  p. 1039
6.2.5A.3.3Minimum conformance requirements  p. 1039
6.2.5A.3.4Test description  p. 1041
6.2.5A.3.5Test requirement  p. 1044
6.2.5A.4Configured UE transmitted Output Power for CA (intra-band non-contiguous DL CA and UL CA)  p. 1044
6.2.5A.4.1Test purpose  p. 1044
6.2.5A.4.2Test applicability  p. 1044
6.2.5A.4.3Minimum conformance requirements  p. 1044
6.2.5A.4.4Test description  p. 1046
6.2.5A.4.5Test requirement  p. 1048
6.2.5A.5Configured UE transmitted Output Power for CA (3UL CA)  p. 1048
6.2.5A.5.1Test purpose  p. 1048
6.2.5A.5.2Test applicability  p. 1048
6.2.5A.5.3Minimum conformance requirements  p. 1048
6.2.5A.5.4Test description  p. 1052
6.2.5A.5.5Test requirement  p. 1055
6.2.5A.6Configured UE transmitted Output Power for CA (4UL CA)  p. 1056
6.2.5A.6.1Test purpose  p. 1056
6.2.5A.6.2Test applicability  p. 1056
6.2.5A.6.3Minimum conformance requirements  p. 1056
6.2.5A.6.4Test description  p. 1056
6.2.5A.6.5Test requirement  p. 1059
6.2.5BConfigured UE transmitted Output Power for UL-MIMO  p. 1059
6.2.5B.1Test purpose  p. 1059
6.2.5B.2Test applicability  p. 1059
6.2.5B.3Minimum conformance requirements  p. 1059
6.2.5B.4Test description  p. 1060
6.2.5B.4.1Initial conditions  p. 1060
6.2.5B.4.2Test procedure  p. 1061
6.2.5B.4.3Message contents  p. 1061
6.2.5B.5Test requirement  p. 1062
6.2.5EConfigured UE transmitted Output Power for UE category 0  p. 1062
6.2.5E.1Test purpose  p. 1062
6.2.5E.2Test applicability  p. 1062
6.2.5E.3Minimum conformance requirements  p. 1063
6.2.5E.4Test description  p. 1063
6.2.5E.4.1Initial conditions  p. 1063
6.2.5E.4.2Test procedure  p. 1063
6.2.5E.4.3Message contents  p. 1063
6.2.5E.5Test requirement  p. 1063
6.2.5EAConfigured UE transmitted Power for UE category M1  p. 1064
6.2.5EA.1Test purpose  p. 1064
6.2.5EA.2Test applicability  p. 1064
6.2.5EA.3Minimum conformance requirements  p. 1064
6.2.5EA.4Test description  p. 1065
6.2.5EA.4.1Initial condition  p. 1065
6.2.5EA.4.2Test procedure  p. 1066
6.2.5EA.4.3Message contents  p. 1066
6.2.5EA.5Test requirements  p. 1067
6.2.5EBConfigured UE transmitted Power for UE category 1bis  p. 1068
6.2.5EB.1Test purpose  p. 1068
6.2.5EB.2Test applicability  p. 1068
6.2.5EB.3Minimum conformance requirements  p. 1068
6.2.5EB.4Test description  p. 1068
6.2.5EB.4.1Initial conditions  p. 1068
6.2.5EB.4.2Test procedure  p. 1068
6.2.5EB.4.3Message contents  p. 1068
6.2.5EB.5Test requirement  p. 1069
6.2.5ECConfigured UE transmitted Power for UE category M2  p. 1069
6.2.5EC.1Test purpose  p. 1069
6.2.5EC.2Test applicability  p. 1069
6.2.5EC.3Minimum conformance requirements  p. 1069
6.2.5EC.4Test description  p. 1069
6.2.5EC.4.1Initial condition  p. 1069
6.2.5EC.4.2Test procedure  p. 1070
6.2.5EC.4.3Message contents  p. 1070
6.2.5EC.5Test requirements  p. 1070
6.2.5FConfigured UE transmitted Output Power for UE category NB1 and NB2  p. 1070
6.2.5F.4Test description  p. 1071
6.2.5F.4.1Initial conditions  p. 1071
6.2.5F.4.2Test procedure  p. 1072
6.2.5F.4.3Message contents  p. 1072
6.2.5F.5Test requirement  p. 1073
6.2.5FAConfigured UE transmitted Output Power for UE category NB1 and NB2/Power Class 6  p. 1074
6.2.5FA.4Test description  p. 1074
6.2.5FA.4.1Initial conditions  p. 1074
6.2.5FA.4.2Test procedure  p. 1075
6.2.5FA.4.3Message contents  p. 1075
6.2.5FA.5Test requirement  p. 1075
6.2.5GConfigured UE transmitted Output Power for V2X Communication  p. 1075
6.2.5G.1Configured UE transmitted Output Power for V2X Communication / Non-concurrent with E-UTRA uplink transmission  p. 1075
6.2.5G.1.1Test purpose  p. 1075
6.2.5G.1.2Test applicability  p. 1075
6.2.5G.1.3Minimum conformance requirements  p. 1076
6.2.5G.1.4Test description  p. 1076
6.2.5G.1.5Test requirements  p. 1078
6.2.5G.2Configured UE transmitted Output Power for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmission  p. 1078
6.2.5G.2.1Test purpose  p. 1078
6.2.5G.2.2Test applicability  p. 1078
6.2.5G.2.3Minimum conformance requirements  p. 1078
6.2.5G.2.4Test description  p. 1080
6.2.5G.2.4.1Initial conditions  p. 1080
6.2.5G.2.4.2Test procedure  p. 1081
6.2.5G.2.4.3Message contents  p. 1081
6.2.5G.2.5Test requirements  p. 1082
6.2.5G.3Configured UE transmitted Output Power for V2X Communication / Intra-band contiguous multi-carrier operation  p. 1083
6.2.5G.3.1Test purpose  p. 1083
6.2.5G.3.2Test applicability  p. 1083
6.2.5G.3.3Minimum conformance requirements  p. 1083
6.2.5G.3.4Test description  p. 1083
6.2.5G.3.4.1Initial conditions  p. 1083
6.2.5G.3.4.2Test procedure  p. 1084
6.2.5G.3.4.3Message contents  p. 1084
6.2.5G.3.5Test requirement  p. 1085
6.3Output Power Dynamics  p. 1085
6.3.1Void  p. …
6.3.2Minimum Output Power  p. 1085
6.3.2.1Test purpose  p. 1085
6.3.2.2Test applicability  p. 1085
6.3.2.3Minimum conformance requirements  p. 1085
6.3.2.4Test description  p. 1086
6.3.2.4.1Initial conditions  p. 1086
6.3.2.4.2Test procedure  p. 1086
6.3.2.4.3Message contents  p. 1087
6.3.2.5Test requirement  p. 1087
6.3.2AMinimum Output Power for CA  p. 1087
6.3.2A.0Minimum conformance requirements  p. 1087
6.3.2A.1Minimum Output Power for CA (intra-band contiguous DL CA and UL CA)  p. 1088
6.3.2A.1.1Test purpose  p. 1088
6.3.2A.1.2Test applicability  p. 1088
6.3.2A.1.3Minimum conformance requirements  p. 1088
6.3.2A.1.4Test description  p. 1088
6.3.2A.1.4.1Initial conditions  p. 1088
6.3.2A.1.4.2Test procedure  p. 1089
6.3.2A.1.4.3Message contents  p. 1090
6.3.2A.1.5Test requirements  p. 1090
6.3.2A.2Minimum Output Power for CA (inter-band DL CA and UL CA)  p. 1090
6.3.2A.2.1Test purpose  p. 1090
6.3.2A.2.2Test applicability  p. 1090
6.3.2A.2.3Minimum conformance requirements  p. 1090
6.3.2A.2.4Test description  p. 1090
6.3.2A.2.4.1Initial conditions  p. 1090
6.3.2A.2.4.2Test procedure  p. 1092
6.3.2A.2.4.3Message contents  p. 1092
6.3.2A.2.5Test requirements  p. 1092
6.3.2A.3Minimum Output Power for CA (intra-band non-contiguous DL CA and UL CA)  p. 1092
6.3.2A.3.1Test purpose  p. 1092
6.3.2A.3.2Test applicability  p. 1092
6.3.2A.3.3Minimum conformance requirements  p. 1092
6.3.2A.3.4Test description  p. 1093
6.3.2A.3.4.1Initial conditions  p. 1093
6.3.2A.3.4.2Test procedure  p. 1093
6.3.2A.3.4.3Message contents  p. 1094
6.3.2A.3.5Test requirements  p. 1094
6.3.2A.4Minimum Output Power for CA (3UL CA)  p. 1094
6.3.2A.4.1Test purpose  p. 1094
6.3.2A.4.2Test applicability  p. 1094
6.3.2A.4.3Minimum conformance requirements  p. 1094
6.3.2A.4.4Test description  p. 1095
6.3.2A.4.4.1Initial conditions  p. 1095
6.3.2A.4.4.2Test procedure  p. 1096
6.3.2A.4.4.3Message contents  p. 1097
6.3.2A.4.5Test requirements  p. 1097
6.3.2A.5Minimum Output Power for CA (4UL CA)  p. 1097
6.3.2A.5.1Test purpose  p. 1097
6.3.2A.5.2Test applicability  p. 1097
6.3.2A.5.3Minimum conformance requirements  p. 1097
6.3.2A.5.4Test description  p. 1098
6.3.2A.5.5Test Requirements  p. 1099
6.3.2BMinimum Output Power for UL-MIMO  p. 1099
6.3.2B.1Test purpose  p. 1099
6.3.2B.2Test applicability  p. 1100
6.3.2B.3Minimum conformance requirements  p. 1100
6.3.2B.4Test description  p. 1100
6.3.2B.4.1Initial conditions  p. 1100
6.3.2B.4.2Test procedure  p. 1101
6.3.2B.4.3Message contents  p. 1101
6.3.2B.5Test requirement  p. 1101
6.3.2EMinimum Output Power for UE category 0  p. 1101
6.3.2E.1Test purpose  p. 1101
6.3.2E.2Test applicability  p. 1101
6.3.2E.3Minimum conformance requirements  p. 1101
6.3.2E.4Test description  p. 1102
6.3.2E.4.1Initial conditions  p. 1102
6.3.2E.4.2Test procedure  p. 1102
6.3.2E.4.3Message contents  p. 1102
6.3.2E.5Test requirement  p. 1102
6.3.2EAMinimum Output Power for UE category M1  p. 1103
6.3.2EA.1Test purpose  p. 1103
6.3.2EA.2Test applicability  p. 1103
6.3.2EA.3Minimum conformance requirements  p. 1103
6.3.2EA.4Test description  p. 1103
6.3.2EA.4.1Initial condition  p. 1103
6.3.2EA.4.2Test procedure  p. 1104
6.3.2EA.4.3Message contents  p. 1104
6.3.2EA.5Test requirements  p. 1104
6.3.2EBMinimum Output Power for UE category 1bis  p. 1105
6.3.2EB.1Test purpose  p. 1105
6.3.2EB.2Test applicability  p. 1105
6.3.2EB.3Minimum conformance requirements  p. 1105
6.3.2EB.4Test description  p. 1105
6.3.2EB.4.1Initial conditions  p. 1105
6.3.2EB.4.2Test procedure  p. 1105
6.3.2EB.4.3Message contents  p. 1105
6.3.2EB.5Test requirement  p. 1105
6.3.2ECMinimum Output Power for UE category M2  p. 1106
6.3.2EC.1Test purpose  p. 1106
6.3.2EC.2Test applicability  p. 1106
6.3.2EC.3Minimum conformance requirements  p. 1106
6.3.2EC.4Test description  p. 1106
6.3.2EC.4.1Initial condition  p. 1106
6.3.2EC.4.2Test procedure  p. 1106
6.3.2EC.4.3Message contents  p. 1106
6.3.2EC.5Test requirements  p. 1106
6.3.2FMinimum Output Power for category NB1 and NB2  p. 1107
6.3.2F.4-  p. 1107
6.3.2F.4.1Initial conditions  p. 1107
6.3.2F.4.2Test procedure  p. 1108
6.3.2F.4.3Message contents  p. 1108
6.3.2F.5Test requirements  p. 1109
6.3.2GMinimum output power for V2X Communication  p. 1109
6.3.2G.1Minimum output power for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 1109
6.3.2G.1.1Test purpose  p. 1109
6.3.2G.1.2Test applicability  p. 1109
6.3.2G.1.3Minimum conformance requirements  p. 1109
6.3.2G.1.4Test description  p. 1109
6.3.2G.1.4.1Initial conditions  p. 1109
6.3.2G.1.4.2Test procedure  p. 1110
6.3.2G.1.4.3Message contents  p. 1110
6.3.2G.1.5Test requirements  p. 1110
6.3.2G.2Minimum output power for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions  p. 1111
6.3.2G.2.1Test purpose  p. 1111
6.3.2G.2.2Test applicability  p. 1111
6.3.2G.2.3Minimum conformance requirements  p. 1111
6.3.2G.2.4Test description  p. 1111
6.3.2G.2.4.1Initial conditions  p. 1111
6.3.2G.2.4.2Test procedure  p. 1112
6.3.2G.2.4.3Message contents  p. 1112
6.3.2G.2.5Test requirements  p. 1113
6.3.2G.3Minimum output power for V2X Communication / Intra-band contiguous multi-carrier operation  p. 1113
6.3.2G.3.1Test purpose  p. 1113
6.3.2G.3.2Test applicability  p. 1113
6.3.2G.3.3Minimum conformance requirements  p. 1113
6.3.2G.3.4Test description  p. 1114
6.3.2G.3.4.1Initial conditions  p. 1114
6.3.2G.3.4.2Test procedure  p. 1115
6.3.2G.3.4.3Message contents  p. 1115
6.3.2G.3.5Test requirements  p. 1115
6.3.3Transmit OFF power  p. 1115
6.3.3.1Test purpose  p. 1115
6.3.3.2Test applicability  p. 1115
6.3.3.3Minimum conformance requirement  p. 1115
6.3.3.4Test description  p. 1116
6.3.3.5Test requirement  p. 1116
6.3.3AUE Transmit OFF power for CA  p. 1116
6.3.3A.0Minimum conformance requirements  p. 1116
6.3.3A.1UE Transmit OFF power for CA (intra-band contiguous DL CA and UL CA)  p. 1117
6.3.3A.1.1Test purpose  p. 1117
6.3.3A.1.2Test applicability  p. 1117
6.3.3A.1.3Minimum conformance requirements  p. 1117
6.3.3A.1.4Test description  p. 1117
6.3.3A.1.5Test Requirements  p. 1117
6.3.3A.2UE Transmit OFF power for CA (inter-band DL CA and UL CA)  p. 1117
6.3.3A.2.1Test purpose  p. 1117
6.3.3A.2.2Test applicability  p. 1118
6.3.3A.2.3Minimum conformance requirements  p. 1118
6.3.3A.2.4Test description  p. 1118
6.3.3A.2.5Test Requirements  p. 1118
6.3.3A.3UE Transmit OFF power for CA (intra-band non-contiguous DL CA and UL CA)  p. 1118
6.3.3A.3.1Test purpose  p. 1118
6.3.3A.3.2Test applicability  p. 1118
6.3.3A.3.3Minimum conformance requirements  p. 1118
6.3.3A.3.4Test description  p. 1118
6.3.3A.3.5Test Requirements  p. 1119
6.3.3A.4UE Transmit OFF power for CA (3UL CA)  p. 1119
6.3.3A.4.1Test purpose  p. 1119
6.3.3A.4.2Test applicability  p. 1119
6.3.3A.4.3Minimum conformance requirements  p. 1119
6.3.3A.4.4Test description  p. 1119
6.3.3A.4.5Test Requirements  p. 1119
6.3.3A.5UE Transmit OFF power for CA (4UL CA)  p. 1120
6.3.3A.5.1Test purpose  p. 1120
6.3.3A.5.2Test applicability  p. 1120
6.3.3A.5.3Minimum conformance requirements  p. 1120
6.3.3A.5.4Test description  p. 1120
6.3.3A.5.5Test Requirements  p. 1120
6.3.3BUE Transmit OFF power for UL-MIMO  p. 1120
6.3.3B.1Test purpose  p. 1120
6.3.3B.2Test applicability  p. 1120
6.3.3B.3Minimum conformance requirement  p. 1120
6.3.3B.4Test description  p. 1121
6.3.3B.5Test requirement  p. 1121
6.3.3CVoid  p. …
6.3.3DUE Transmit OFF power for ProSe  p. 1121
6.3.3D.0Minimum conformance requirements  p. 1121
6.3.3D.1UE Transmit OFF power for ProSe Direct Discovery  p. 1122
6.3.3D.1.1Test purpose  p. 1122
6.3.3D.1.2Test applicability  p. 1122
6.3.3D.1.3Minimum Conformance requirements  p. 1122
6.3.3D.1.4Test description  p. 1122
6.3.3D.1.5Test requirements  p. 1123
6.3.3EUE Transmit OFF power for UE category 0  p. 1124
6.3.3E.1Test purpose  p. 1124
6.3.3E.2Test applicability  p. 1124
6.3.3E.3Minimum conformance requirement  p. 1124
6.3.3E.4Test description  p. 1124
6.3.3E.5Test requirement  p. 1124
6.3.3EAUE Transmit OFF power for UE category M1  p. 1124
6.3.3EA.1Test purpose  p. 1124
6.3.3EA.2Test applicability  p. 1124
6.3.3EA.3Minimum conformance requirements  p. 1125
6.3.3EA.4Test description  p. 1125
6.3.3EA.5Test requirements  p. 1125
6.3.3EBUE Transmit OFF power for UE category 1bis  p. 1125
6.3.3EB.1Test purpose  p. 1125
6.3.3EB.2Test applicability  p. 1125
6.3.3EB.3Minimum conformance requirements  p. 1125
6.3.3EB.4Test description  p. 1126
6.3.3EB.5Test requirement  p. 1126
6.3.3ECUE Transmit OFF power for UE category M2  p. 1126
6.3.3EC.1Test purpose  p. 1126
6.3.3EC.2Test applicability  p. 1126
6.3.3EC.3Minimum conformance requirements  p. 1126
6.3.3EC.4Test description  p. 1126
6.3.3EC.5Test requirements  p. 1126
6.3.3FTransmit OFF power for category NB1 and NB2  p. 1126
6.3.3F.4Test description  p. 1127
6.3.3F.5Test requirement  p. 1127
6.3.3GUE Transmit OFF power for V2X Communication  p. 1127
6.3.3G.1UE Transmit OFF power for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 1127
6.3.3G.1.1Test purpose  p. 1127
6.3.3G.1.2Test applicability  p. 1127
6.3.3G.1.3Minimum conformance requirements  p. 1127
6.3.3G.1.4Test description  p. 1127
6.3.3G.1.5Test requirements  p. 1127
6.3.3G.2UE Transmit OFF power for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions  p. 1128
6.3.3G.2.1Test purpose  p. 1128
6.3.3G.2.2Test applicability  p. 1128
6.3.3G.2.3Minimum conformance requirements  p. 1128
6.3.3G.2.4Test description  p. 1128
6.3.3G.2.5Test requirements  p. 1128
6.3.3G.3UE Transmit OFF power for V2X Communication / Intra-band contiguous multi-carrier operation  p. 1128
6.3.3G.3.1Test purpose  p. 1128
6.3.3G.3.2Test applicability  p. 1128
6.3.3G.3.3Minimum conformance requirements  p. 1129
6.3.3G.3.4Test description  p. 1129
6.3.3G.3.5Test requirement  p. 1129
6.3.4ON/OFF time mask  p. 1129
6.3.4.1General ON/OFF time mask  p. 1129
6.3.4.1.1Test purpose  p. 1129
6.3.4.1.2Test applicability  p. 1129
6.3.4.1.3Minimum conformance requirement  p. 1129
6.3.4.1.4Test description  p. 1130
6.3.4.1.5Test requirement  p. 1132
6.3.4.1_sGeneral ON/OFF time mask for subslot/slot TTI  p. 1132
6.3.4.2PRACH and SRS time mask  p. 1136
6.3.4.2.1PRACH time mask  p. 1136
6.3.4.2.2SRS time mask  p. 1139
6.3.4AON/OFF time mask for CA  p. 1144
6.3.4A.0Minimum conformance requirements  p. 1144
6.3.4A.1General ON/OFF time mask for CA  p. 1144
6.3.4A.1.1General ON/OFF time mask for CA (intra-band contiguous DL CA and UL CA)  p. 1144
6.3.4A.1.1.4-  p. 1146
6.3.4A.1.1.4.2Test procedure  p. 1146
6.3.4A.1.1.4.3Message contents  p. 1147
6.3.4A.1.1.5Test requirement  p. 1148
6.3.4A.1.2General ON/OFF time mask for CA (inter-band DL CA and UL CA)  p. 1148
6.3.4A.1.2.4-  p. 1149
6.3.4A.1.2.4.2Test procedure  p. 1149
6.3.4A.1.2.4.3Message contents  p. 1149
6.3.4A.1.2.5Test requirement  p. 1149
6.3.4A.1.3General ON/OFF time mask for CA (intra-band non-contiguous DL CA and UL CA)  p. 1150
6.3.4A.1.3.4-  p. 1151
6.3.4A.1.3.4.2Test procedure  p. 1151
6.3.4A.1.3.4.3Message contents  p. 1151
6.3.4A.1.3.5Test requirement  p. 1151
6.3.4A.1.4General ON/OFF time mask for CA (3UL CA)  p. 1152
6.3.4A.1.4.4-  p. 1153
6.3.4A.1.4.4.2Test procedure  p. 1153
6.3.4A.1.4.4.3Message contents  p. 1154
6.3.4A.1.4.5Test requirement  p. 1154
6.3.4A.1.5General ON/OFF time mask for CA (4UL CA)  p. 1154
6.3.4BON/OFF time mask for UL-MIMO  p. 1157
6.3.4B.1General ON/OFF time mask for UL-MIMO  p. 1157
6.3.4B.1.1Test purpose  p. 1157
6.3.4B.1.2Test applicability  p. 1157
6.3.4B.1.3Minimum conformance requirement  p. 1157
6.3.4B.1.4Test description  p. 1157
6.3.4B.1.5Test requirement  p. 1159
6.3.4CON/OFF time mask for DC  p. 1160
6.3.4C.1General ON/OFF time mask for Dual Connectivity  p. 1160
6.3.4C.1.1Test purpose  p. 1160
6.3.4C.1.2Test applicability  p. 1160
6.3.4C.1.3Minimum conformance requirements  p. 1160
6.3.4C.1.4Test description  p. 1160
6.3.4C.1.4.1Initial conditions  p. 1160
6.3.4C.1.4.2Test procedure  p. 1161
6.3.4C.1.4.3Message contents  p. 1162
6.3.4C.1.5Test requirement  p. 1163
6.3.4C.1_1General ON/OFF time mask for asynchronous Dual Connectivity  p. 1163
6.3.4C.1_1.1Test purpose  p. 1163
6.3.4C.1_1.2Test applicability  p. 1163
6.3.4C.1_1.3Minimum conformance requirements  p. 1163
6.3.4C.1_1.4Test description  p. 1164
6.3.4C.1_1.4.1Initial conditions  p. 1164
6.3.4C.1_1.4.2Test procedure  p. 1165
6.3.4C.1_1.4.3Message contents  p. 1165
6.3.4C.1_1.5Test requirement  p. 1167
6.3.4EON/OFF time mask for UE category 0  p. 1168
6.3.4E.1General ON/OFF time mask for UE category 0  p. 1168
6.3.4E.1.1Test purpose  p. 1168
6.3.4E.1.2Test applicability  p. 1168
6.3.4E.1.3Minimum conformance requirement  p. 1168
6.3.4E.1.4Test description  p. 1168
6.3.4E.1.5Test requirement  p. 1169
6.3.4E.2PRACH and SRS time mask for UE category 0  p. 1170
6.3.4E.2.1PRACH time mask for UE category 0  p. 1170
6.3.4E.2.2SRS time mask for UE category 0  p. 1171
6.3.4EAON/OFF time mask for UE category M1  p. 1172
6.3.4EA.1General ON/OFF time mask for UE category M1  p. 1172
6.3.4EA.1.1Test purpose  p. 1172
6.3.4EA.1.2Test applicability  p. 1172
6.3.4EA.1.3Minimum conformance requirement  p. 1172
6.3.4EA.1.4Test description  p. 1172
6.3.4EA.1.5Test requirement  p. 1174
6.3.4EA.2PRACH and SRS ON/OFF time mask for UE category M1  p. 1174
6.3.4EA.2.1PRACH time mask for UE category M1  p. 1174
6.3.4EA.2.2SRS time mask for UE category M1  p. 1176
6.3.4EBON/OFF time mask for UE category 1bis  p. 1178
6.3.4EB.1General ON/OFF time mask for UE category 1bis  p. 1178
6.3.4EB.1.1Test purpose  p. 1178
6.3.4EB.1.2Test applicability  p. 1178
6.3.4EB.1.3Minimum conformance requirement  p. 1178
6.3.4EB.1.4Test description  p. 1178
6.3.4EB.1.5Test requirement  p. 1179
6.3.4EB.2PRACH and SRS ON/OFF time mask for UE category 1bis  p. 1179
6.3.4EB.2.1PRACH time mask for UE category 1bis  p. 1179
6.3.4EB.2.1.1Test purpose  p. 1179
6.3.4EB.2.1.2Test applicability  p. 1179
6.3.4EB.2.1.3Minimum conformance requirement  p. 1179
6.3.4EB.2.1.4Test description  p. 1179
6.3.4EB.2.1.4.1Initial conditions  p. 1179
6.3.4EB.2.1.4.2Test procedure  p. 1180
6.3.4EB.2.1.4.3Message contents  p. 1180
6.3.4EB.2.1.5Test requirement  p. 1180
6.3.4EB.2.2SRS time mask for UE category 1bis  p. 1180
6.3.4EB.2.2.1Test purpose  p. 1180
6.3.4EB.2.2.2Test applicability  p. 1180
6.3.4EB.2.2.3Minimum conformance requirement  p. 1180
6.3.4EB.2.2.4Test description  p. 1180
6.3.4EB.2.2.4.1Initial conditions  p. 1180
6.3.4EB.2.2.4.2Test procedure  p. 1180
6.3.4EB.2.2.4.3Message contents  p. 1181
6.3.4EB.2.2.5Test requirement  p. 1181
6.3.4ECON/OFF time mask for UE category M2  p. 1181
6.3.4EC.1General ON/OFF time mask for UE category M2  p. 1181
6.3.4EC.1.1Test purpose  p. 1181
6.3.4EC.1.2Test applicability  p. 1181
6.3.4EC.1.3Minimum conformance requirement  p. 1181
6.3.4EC.1.4Test description  p. 1181
6.3.4EC.1.5Test requirement  p. 1182
6.3.4EC.2PRACH and SRS ON/OFF time mask for UE category M2  p. 1182
6.3.4EC.2.1PRACH time mask for UE category M2  p. 1182
6.3.4EC.2.2SRS time mask for UE category M2  p. 1184
6.3.4FON/OFF time mask for category NB1 and NB2  p. 1185
6.3.4F.1General ON/OFF time mask for category NB1 and NB2  p. 1185
6.3.4F.2NPRACH time mask for category NB1 and NB2  p. 1187
6.3.4F.2.3Minimum conformance requirement  p. 1188
6.3.4F.2.4Test description  p. 1188
6.3.4F.2.5Test requirement  p. 1190
6.3.4GON/OFF time mask for V2X Communication  p. 1190
6.3.4G.1General ON/OFF time mask for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 1190
6.3.4G.1.1Test purpose  p. 1190
6.3.4G.1.2Test applicability  p. 1190
6.3.4G.1.3Minimum conformance requirements  p. 1190
6.3.4G.1.4Test description  p. 1190
6.3.4G.1.4.1Initial conditions  p. 1190
6.3.4G.1.4.2Test procedure  p. 1191
6.3.4G.1.4.3Message contents  p. 1191
6.3.4G.1.5Test requirement  p. 1192
6.3.4G.2General ON/OFF time mask for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions  p. 1192
6.3.4G.2.1Test purpose  p. 1192
6.3.4G.2.2Test applicability  p. 1192
6.3.4G.2.3Minimum conformance requirements  p. 1192
6.3.4G.2.4Test description  p. 1192
6.3.4G.2.4.1Initial conditions  p. 1192
6.3.4G.2.4.2Test procedure  p. 1193
6.3.4G.2.4.3Message contents  p. 1194
6.3.4G.2.5Test requirement  p. 1195
6.3.4G.3General ON/OFF time mask for V2X Communication / Intra-band contiguous multi-carrier operation  p. 1195
6.3.4G.3.1Test purpose  p. 1195
6.3.4G.3.2Test applicability  p. 1195
6.3.4G.3.3Minimum conformance requirements  p. 1195
6.3.4G.3.4Test description  p. 1195
6.3.4G.3.4.1Initial conditions  p. 1195
6.3.4G.3.4.2Test procedure  p. 1196
6.3.4G.3.4.3Message contents  p. 1196
6.3.4G.3.5Test requirement  p. 1197
6.3.4G.4PSSS/SSSS time mask for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 1197
6.3.4G.4.1Test purpose  p. 1197
6.3.4G.4.2Test applicability  p. 1197
6.3.4G.4.3Minimum conformance requirements  p. 1197
6.3.4G.4.4Test description  p. 1198
6.3.4G.4.4.1Initial conditions  p. 1198
6.3.4G.4.4.2Test procedure  p. 1199
6.3.4G.4.4.3Message contents  p. 1199
6.3.4G.4.5Test requirement  p. 1199
6.3.5Power Control  p. 1199
6.3.5.1Power Control Absolute power tolerance  p. 1200
6.3.5.1.1Test purpose  p. 1200
6.3.5.1.2Test applicability  p. 1200
6.3.5.1.3Minimum conformance requirement  p. 1200
6.3.5.1.4Test description  p. 1200
6.3.5.1.5Test requirement  p. 1202
6.3.5.2Power Control Relative power tolerance  p. 1203
6.3.5.2.1Test purpose  p. 1203
6.3.5.2.2Test applicability  p. 1203
6.3.5.2.3Minimum conformance requirement  p. 1203
6.3.5.2.4Test description  p. 1204
6.3.5.2.5Test requirement  p. 1211
6.3.5.3Aggregate power control tolerance  p. 1222
6.3.5.3.1Test purpose  p. 1222
6.3.5.3.2Test applicability  p. 1222
6.3.5.3.3Minimum conformance requirement  p. 1222
6.3.5.3.4Test description  p. 1222
6.3.5.3.5Test requirement  p. 1225
6.3.5_1Power Control for HPUE  p. 1225
6.3.5_1.1Power Control Absolute power tolerance for HPUE  p. 1225
6.3.5_1.1.1Test purpose  p. 1225
6.3.5_1.1.2Test applicability  p. 1225
6.3.5_1.1.3Minimum conformance requirement  p. 1225
6.3.5_1.1.4Test description  p. 1225
6.3.5_1.1.5Test requirement  p. 1226
6.3.5_1.2Power Control Relative power tolerance for HPUE  p. 1227
6.3.5_1.2.1Test purpose  p. 1227
6.3.5_1.2.2Test applicability  p. 1227
6.3.5_1.2.3Minimum conformance requirement  p. 1227
6.3.5_1.2.4Test description  p. 1227
6.3.5_1.2.5Test requirement  p. 1227
6.3.5_1.3Aggregate power control tolerance for HPUE  p. 1227
6.3.5_1.3.1Test purpose  p. 1227
6.3.5_1.3.2Test applicability  p. 1227
6.3.5_1.3.3Minimum conformance requirement  p. 1228
6.3.5_1.3.4Test description  p. 1228
6.3.5_1.3.5Test requirement  p. 1228
6.3.5APower Control for CA  p. 1228
6.3.5A.1Power Control Absolute power tolerance for CA  p. 1228
6.3.5A.1.0Minimum conformance requirements  p. 1228
6.3.5A.1.1Power Control Absolute power tolerance for CA (intra-band contiguous DL CA and UL CA)  p. 1228
6.3.5A.1.2Power Control Absolute power tolerance for CA (inter-band DL CA and UL CA)  p. 1232
6.3.5A.1.3Power Control Absolute power tolerance for CA (intra-band non-contiguous DL CA and UL CA)  p. 1237
6.3.5A.1.4Power Control Absolute power tolerance for CA (3UL CA)  p. 1241
6.3.5A.1.4.1Test purpose  p. 1241
6.3.5A.1.4.2Test applicability  p. 1241
6.3.5A.1.4.3Minimum conformance requirements  p. 1241
6.3.5A.1.4.4Test description  p. 1241
6.3.5A.1.4.5Test Requirements  p. 1245
6.3.5A.1.5Power Control Absolute power tolerance for CA(SRS carrier based switching)  p. 1246
6.3.5A.1.6Power control absolute power tolerance for CA (4UL CA)  p. 1250
6.3.5A.2Power Control Relative power tolerance for CA  p. 1255
6.3.5A.2.0Minimum conformance requirements  p. 1255
6.3.5A.2.1Power Control Relative power tolerance for CA (intra-band contiguous DL CA and UL CA)  p. 1257
6.3.5A.2.2Power Control Relative power tolerance for CA (inter-band DL CA and UL CA)  p. 1267
6.3.5A.2.3Power Control Relative power tolerance for CA (intra-band non-contiguous DL CA and UL CA)  p. 1289
6.3.5A.2.4Power Control Relative power tolerance for CA (3UL CA)  p. 1292
6.3.5A.2.4.1Power Control Relative power tolerance for CA (intra-band contiguous 3DL CA and 3UL CA)  p. 1292
6.3.5A.2.4.1.1Test purpose  p. 1292
6.3.5A.2.4.1.2Test applicability  p. 1292
6.3.5A.2.4.1.3Minimum conformance requirements  p. 1292
6.3.5A.2.4.1.4Test description  p. 1292
6.3.5A.2.4.1.4.1Initial conditions  p. 1292
6.3.5A.2.4.1.4.2Test procedure  p. 1294
6.3.5A.2.4.1.4.3Message contents  p. 1301
6.3.5A.2.4.1.5Test Requirements  p. 1301
6.3.5A.2.4.2Power Control Relative power tolerance for CA (inter-band 3DL CA and 3UL CA)  p. 1302
6.3.5A.2.4.2.1Test purpose  p. 1302
6.3.5A.2.4.2.2Test applicability  p. 1302
6.3.5A.2.4.2.3Minimum conformance requirement  p. 1302
6.3.5A.2.4.2.4Test description  p. 1302
6.3.5A.2.4.2.4.1Initial conditions  p. 1302
6.3.5A.2.4.2.4.2Test procedure  p. 1306
6.3.5A.2.4.2.4.3Message contents  p. 1311
6.3.5A.2.4.2.5Test requirement  p. 1311
6.3.5A.2.4.3Power Control Relative power tolerance for CA (intra-band non-contiguous 3DL CA and 3UL CA)  p. 1318
6.3.5A.2.4.3.1Test purpose  p. 1318
6.3.5A.2.4.3.2Test applicability  p. 1318
6.3.5A.2.4.3.3Minimum conformance requirement  p. 1318
6.3.5A.2.4.3.4Test description  p. 1319
6.3.5A.2.4.3.4.1Initial conditions  p. 1319
6.3.5A.2.4.3.4.2Test procedure  p. 1320
6.3.5A.2.4.3.4.3Message contents  p. 1320
6.3.5A.2.4.3.5Test requirement  p. 1320
6.3.5A.3Aggregate power control tolerance for CA  p. 1321
6.3.5A.3.0Minimum conformance requirements  p. 1321
6.3.5A.3.1Aggregate power control tolerance for CA (intra-band contiguous DL CA and UL CA)  p. 1321
6.3.5A.3.2Aggregate power control tolerance for CA (inter-band DL CA and UL CA)  p. 1325
6.3.5A.3.3Aggregate power control tolerance for CA (intra-band non-contiguous DL CA and UL CA)  p. 1327
6.3.5A.3.4Aggregate Power Control Tolerance for CA (3UL CA)  p. 1329
6.3.5A.3.4.1Test purpose  p. 1329
6.3.5A.3.4.2Test applicability  p. 1329
6.3.5A.3.4.3Minimum conformance requirements  p. 1329
6.3.5A.3.4.4Test description  p. 1329
6.3.5A.3.4.5Test Requirements  p. 1334
6.3.5A.3.5Aggregate power control tolerance for CA (4UL CA)  p. 1334
6.3.5BPower Control for UL- MIMO  p. 1339
6.3.5B.1Power Control Absolute Power Tolerance for UL- MIMO  p. 1339
6.3.5B.1.1Test purpose  p. 1339
6.3.5B.1.2Test applicability  p. 1339
6.3.5B.1.3Minimum conformance requirement  p. 1339
6.3.5B.1.4Test description  p. 1340
6.3.5B.1.5Test requirement  p. 1341
6.3.5B.2Power Control Relative power tolerance for UL-MIMO  p. 1342
6.3.5B.2.1Test purpose  p. 1342
6.3.5B.2.2Test applicability  p. 1342
6.3.5B.2.3Minimum conformance requirement  p. 1342
6.3.5B.2.4Test description  p. 1343
6.3.5B.2.5Test requirement  p. 1349
6.3.5B.3Aggregate power control tolerance for UL-MIMO  p. 1359
6.3.5B.3.1Test purpose  p. 1359
6.3.5B.3.2Test applicability  p. 1359
6.3.5B.3.3Minimum conformance requirement  p. 1359
6.3.5B.3.4Test description  p. 1359
6.3.5B.3.5Test requirement  p. 1361
6.3.5CPower Control for DC  p. 1362
6.3.5C.1Void  p. …
6.3.5C.2Power Control Relative power tolerance for Dual Connectivity  p. 1362
6.3.5C.2.1Test purpose  p. 1362
6.3.5C.2.2Test applicability  p. 1362
6.3.5C.2.3Minimum conformance requirement  p. 1362
6.3.5C.2.4Test description  p. 1362
6.3.5C.2.5Test requirement  p. 1370
6.3.5C.2_1Power Control Relative power tolerance for asynchronous Dual Connectivity  p. 1379
6.3.5C.2_1.1Test purpose  p. 1379
6.3.5C.2_1.2Test applicability  p. 1379
6.3.5C.2_1.3Minimum conformance requirement  p. 1379
6.3.5C.2_1.4Test description  p. 1380
6.3.5C.2_1.5Test requirement  p. 1389
6.3.5DTBD  p. 1398
6.3.5EPower Control for UE category 0  p. 1398
6.3.5E.1Power Control Absolute power tolerance for UE category 0  p. 1398
6.3.5E.1.1Test purpose  p. 1398
6.3.5E.1.2Minimum conformance requirement  p. 1398
6.3.5E.1.3Test applicability  p. 1398
6.3.5E.1.4Test description  p. 1399
6.3.5E.1.5Test requirement  p. 1399
6.3.5E.2Power Control Relative power tolerance for UE category 0  p. 1400
6.3.5E.2.1Test purpose  p. 1400
6.3.5E.2.2Test applicability  p. 1400
6.3.5E.2.3Minimum conformance requirement  p. 1400
6.3.5E.2.4Test description  p. 1400
6.3.5E.2.5Test requirement  p. 1409
6.3.5E.3Aggregate power control tolerance for UE category 0  p. 1410
6.3.5E.3.1Test purpose  p. 1410
6.3.5E.3.2Test applicability  p. 1410
6.3.5E.3.3Minimum conformance requirement  p. 1410
6.3.5E.3.4Test description  p. 1410
6.3.5E.3.5Test requirement  p. 1422
6.3.5EAPower control for UE category M1  p. 1422
6.3.5EA.1Power Control Absolute power tolerance for UE category M1  p. 1422
6.3.5EA.1.1Test purpose  p. 1422
6.3.5EA.1.2Test applicability  p. 1422
6.3.5EA.1.3Minimum conformance requirement  p. 1422
6.3.5EA.1.4Test description  p. 1423
6.3.5EA.1.5Test requirement  p. 1424
6.3.5EA.2Power Control Relative power tolerance for UE category M1  p. 1425
6.3.5EA.2.1Test purpose  p. 1425
6.3.5EA.2.2Test applicability  p. 1425
6.3.5EA.2.3Minimum conformance requirement  p. 1425
6.3.5EA.2.4Test description  p. 1426
6.3.5EA.2.5Test requirement  p. 1435
6.3.5EA.3Aggregate power control tolerance for UE category M1  p. 1438
6.3.5EA.3.1Test purpose  p. 1438
6.3.5EA.3.2Test applicability  p. 1438
6.3.5EA.3.3Minimum conformance requirement  p. 1438
6.3.5EA.3.4Test description  p. 1438
6.3.5EA.3.5Test requirement  p. 1441
6.3.5EA.3_1Aggregate power control tolerance for UE category M1 (CE Mode B)  p. 1442
6.3.5EA.3_1.1Test purpose  p. 1442
6.3.5EA.3_1.2Test applicability  p. 1442
6.3.5EA.3_1.3Minimum conformance requirement  p. 1442
6.3.5EA.3_1.4Test description  p. 1443
6.3.5EA.3_1.5Test requirement  p. 1444
6.3.5EBPower Control for UE category 1bis  p. 1444
6.3.5EB.1Power Control Absolute power tolerance for UE category 1bis  p. 1444
6.3.5EB.1.1Test purpose  p. 1444
6.3.5EB.1.2Test applicability  p. 1444
6.3.5EB.1.3Minimum conformance requirement  p. 1444
6.3.5EB.1.4Test description  p. 1444
6.3.5EB.1.4.1Initial conditions  p. 1444
6.3.5EB.1.4.2Test procedure  p. 1444
6.3.5EB.1.4.3Message contents  p. 1444
6.3.5EB.1.5Test requirements  p. 1444
6.3.5EB.2Power Control Relative power tolerance for UE category 1bis  p. 1445
6.3.5EB.2.1Test purpose  p. 1445
6.3.5EB.2.2Test applicability  p. 1445
6.3.5EB.2.3Minimum conformance requirement  p. 1445
6.3.5EB.2.4Test description  p. 1446
6.3.5EB.2.4.1Initial conditions  p. 1446
6.3.5EB.2.4.2Test procedure  p. 1446
6.3.5EB.2.4.3Message contents  p. 1446
6.3.5EB.2.5Test requirements  p. 1446
6.3.5EB.3Aggregate power control tolerance for UE category 1bis  p. 1446
6.3.5EB.3.1Test purpose  p. 1446
6.3.5EB.3.2Test applicability  p. 1446
6.3.5EB.3.3Minimum conformance requirement  p. 1446
6.3.5EB.3.4Test description  p. 1446
6.3.5EB.3.4.1Initial conditions  p. 1446
6.3.5EB.3.4.2Test procedure  p. 1446
6.3.5EB.3.4.3Message contents  p. 1446
6.3.5EB.3.5Test requirements  p. 1446
6.3.5ECPower Control for UE category M2  p. 1447
6.3.5EC.1Power Control Absolute power tolerance for UE category M2  p. 1447
6.3.5EC.1.1Test purpose  p. 1447
6.3.5EC.1.2Test applicability  p. 1447
6.3.5EC.1.3Minimum conformance requirement  p. 1447
6.3.5EC.1.4Test description  p. 1447
6.3.5EC.1.5Test requirement  p. 1447
6.3.5EC.2Power Control Relative power tolerance for UE category M2  p. 1448
6.3.5EC.2.1Test purpose  p. 1448
6.3.5EC.2.2Test applicability  p. 1448
6.3.5EC.2.3Minimum conformance requirement  p. 1448
6.3.5EC.2.4Test description  p. 1448
6.3.5EC.2.5Test requirement  p. 1448
6.3.5EC.3Aggregate power control tolerance for UE category M2  p. 1450
6.3.5EC.3.1Test purpose  p. 1450
6.3.5EC.3.2Test applicability  p. 1451
6.3.5EC.3.3Minimum conformance requirement  p. 1451
6.3.5EC.3.4Test description  p. 1451
6.3.5EC.3.5Test requirement  p. 1452
6.3.5EC.3_1Aggregate power control tolerance for UE category M2 (CE Mode B)  p. 1452
6.3.5EC.3_1.1Test purpose  p. 1452
6.3.5EC.3_1.2Test applicability  p. 1452
6.3.5EC.3_1.3Minimum conformance requirement  p. 1452
6.3.5EC.3_1.4Test description  p. 1453
6.3.5EC.3_1.5Test requirement  p. 1454
6.3.5FPower Control for category NB1 and NB2  p. 1454
6.3.5F.1Power Control Absolute power tolerance for category NB1 and NB2  p. 1454
6.3.5F.1.4Test description  p. 1454
6.3.5F.1.5Test requirement  p. 1457
6.3.5F.2Power Control Relative power tolerance for category NB1 and NB2  p. 1457
6.3.5F.2.4Test description  p. 1458
6.3.5F.2.5Test requirement  p. 1460
6.3.5F.3Aggregate power control tolerance for category NB1 and NB2  p. 1460
6.3.5F.3.3Minimum conformance requirement  p. 1460
6.3.5F.3.4Test description  p. 1461
6.3.5FAPower Control for category NB1 and NB2/Power Class 6  p. 1464
6.3.5FA.1Power Control Absolute power tolerance for category NB1 and NB2/Power Class 6  p. 1464
6.3.5FA.1.4Test description  p. 1465
6.3.5FA.1.5Test requirement  p. 1465
6.3.5FA.2Power Control Relative power tolerance for category NB1 and NB2/Power Class 6  p. 1465
6.3.5FA.2.1Test purpose  p. 1465
6.3.5FA.2.2Test applicability  p. 1465
6.3.5FA.2.4Test description  p. 1466
6.3.5FA.2.5Test requirement  p. 1466
6.3.5FA.3Aggregate power control tolerance for category NB1 and NB2/Power Class 6  p. 1466
6.3.5FA.3.4Test description  p. 1467
6.3.5FA.3.5Test requirement  p. 1467
6.3.5GPower Control Absolute power tolerance for V2X Communication  p. 1467
6.3.5G.1Power Control Absolute power tolerance for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 1467
6.3.5G.2Power Control Absolute power tolerance for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions  p. 1470
6.3.5G.3Power Control Absolute power tolerance for V2X Communication / Intra-band contiguous multi-carrier operation  p. 1474
6.4Void  p. …
6.5Transmit signal quality  p. 1478
6.5.1Frequency Error  p. 1478
6.5.1.1Test purpose  p. 1478
6.5.1.2Test applicability  p. 1478
6.5.1.3Minimum conformance requirements  p. 1478
6.5.1.4Test description  p. 1478
6.5.1.4.1Initial condition  p. 1478
6.5.1.4.2Test procedure  p. 1479
6.5.1.4.3Message contents  p. 1480
6.5.1.5Test requirement  p. 1480
6.5.1AFrequency error for CA  p. 1480
6.5.1A.0Minimum conformance requirements  p. 1480
6.5.1A.1Frequency error for CA (intra-band contiguous DL CA and UL CA)  p. 1480
6.5.1A.1.1Test purpose  p. 1480
6.5.1A.1.2Test applicability  p. 1480
6.5.1A.1.3Minimum conformance requirements  p. 1480
6.5.1A.1.4Test description  p. 1480
6.5.1A.1.5Test Requirements  p. 1482
6.5.1A.2Frequency error for CA (inter-band DL CA and UL CA)  p. 1482
6.5.1A.2.1Test purpose  p. 1482
6.5.1A.2.2Test applicability  p. 1482
6.5.1A.2.3Minimum conformance requirements  p. 1483
6.5.1A.2.4Test description  p. 1483
6.5.1A.2.4.3Message contents  p. 1484
6.5.1A.2.5Test requirement  p. 1485
6.5.1A.3Frequency error for CA (intra-band non-contiguous DL CA and UL CA)  p. 1485
6.5.1A.3.1Test purpose  p. 1485
6.5.1A.3.2Test applicability  p. 1485
6.5.1A.3.3Minimum conformance requirements  p. 1485
6.5.1A.3.4Test description  p. 1485
6.5.1A.3.5Test Requirements  p. 1486
6.5.1A.4Frequency error for CA (3UL CA)  p. 1486
6.5.1A.4.1Test purpose  p. 1487
6.5.1A.4.2Test applicability  p. 1487
6.5.1A.4.3Minimum conformance requirements  p. 1487
6.5.1A.4.4Test description  p. 1487
6.5.1A.4.5Test Requirements  p. 1490
6.5.1A.5Frequency error for CA (4UL CA)  p. 1490
6.5.1A.5.1Test purpose  p. 1490
6.5.1A.5.2Test applicability  p. 1490
6.5.1A.5.3Minimum conformance requirements  p. 1490
6.5.1A.5.4Test description  p. 1490
6.5.1A.5aTest Requirements  p. 1493
6.5.1BFrequency Error for UL-MIMO  p. 1493
6.5.1B.1Test purpose  p. 1493
6.5.1B.2Test applicability  p. 1493
6.5.1B.3Minimum conformance requirements  p. 1493
6.5.1B.4Test description  p. 1493
6.5.1B.4.1Initial condition  p. 1493
6.5.1B.4.2Test procedure  p. 1494
6.5.1B.4.3Message contents  p. 1495
6.5.1B.5Test requirement  p. 1495
6.5.1CTBD  p. 1495
6.5.1DFrequency Error for ProSe  p. 1495
6.5.1D.0Minimum conformance requirements  p. 1495
6.5.1D.1Frequency error for ProSe Direct Discovery  p. 1495
6.5.1D.1.1Test purpose  p. 1495
6.5.1D.1.2Test applicability  p. 1495
6.5.1D.1.3Minimum conformance requirements  p. 1495
6.5.1D.1.4Test description  p. 1496
6.5.1D.1.5Test requirement  p. 1497
6.5.1D.2Frequency error for ProSe Direct Communication  p. 1497
6.5.1D.2.1Test purpose  p. 1498
6.5.1D.2.2Test applicability  p. 1498
6.5.1D.2.3Minimum conformance requirements  p. 1498
6.5.1D.2.4Test description  p. 1498
6.5.1D.2.5Test requirements  p. 1498
6.5.1EFrequency Error for UE category 0  p. 1498
6.5.1E.1Test purpose  p. 1498
6.5.1E.2Test applicability  p. 1498
6.5.1E.3Minimum conformance requirements  p. 1498
6.5.1E.4Test description  p. 1499
6.5.1E.4.1Initial condition  p. 1499
6.5.1E.4.2Test procedure  p. 1499
6.5.1E.4.3Message contents  p. 1499
6.5.1E.5Test requirement  p. 1499
6.5.1EAFrequency Error for UE category M1  p. 1500
6.5.1EA.1Test purpose  p. 1500
6.5.1EA.2Test applicability  p. 1500
6.5.1EA.3Minimum conformance requirements  p. 1500
6.5.1EA.4Test description  p. 1500
6.5.1EA.4.1Initial condition  p. 1500
6.5.1EA.4.2Test procedure  p. 1501
6.5.1EA.4.3Message contents  p. 1501
6.5.1EA.5Test requirement  p. 1501
6.5.1EA_1Frequency Error for UE category M1 (CEmodeB)  p. 1501
6.5.1EA_1.1Test purpose  p. 1501
6.5.1EA_1.2Test applicability  p. 1501
6.5.1EA_1.3Minimum conformance requirements  p. 1501
6.5.1EA_1.4Test description  p. 1502
6.5.1EA_1.4.1Initial condition  p. 1502
6.5.1EA_1.4.2Test procedure  p. 1503
6.5.1EA_1.4.3Message contents  p. 1503
6.5.1EA_1.5Test requirement  p. 1503
6.5.1EBFrequency Error for UE category 1bis  p. 1503
6.5.1EB.1Test purpose  p. 1503
6.5.1EB.2Test applicability  p. 1503
6.5.1EB.3Minimum conformance requirements  p. 1503
6.5.1EB.4Test description  p. 1504
6.5.1EB.4.1Initial conditions  p. 1504
6.5.1EB.4.2Test procedure  p. 1504
6.5.1EB.4.3Message contents  p. 1504
6.5.1EB.5Test requirement  p. 1504
6.5.1ECFrequency Error for UE category M2  p. 1504
6.5.1EC.1Test purpose  p. 1504
6.5.1EC.2Test applicability  p. 1504
6.5.1EC.3Minimum conformance requirements  p. 1504
6.5.1EC.4Test description  p. 1504
6.5.1EC.4.1Initial condition  p. 1504
6.5.1EC.4.2Test procedure  p. 1505
6.5.1EC.4.3Message contents  p. 1505
6.5.1EC.5Test requirements  p. 1505
6.5.1EC_1Frequency Error for UE category M2 (CE Mode B)  p. 1505
6.5.1EC_1.1Test purpose  p. 1505
6.5.1EC_1.2Test applicability  p. 1505
6.5.1EC_1.3Minimum conformance requirements  p. 1505
6.5.1EC_1.4Test description  p. 1506
6.5.1EC_1.4.1Initial condition  p. 1506
6.5.1EC_1.4.2Test procedure  p. 1507
6.5.1EC_1.4.3Message contents  p. 1507
6.5.1EC_1.5Test requirement  p. 1507
6.5.1FFrequency Error for category NB1 and NB2  p. 1507
6.5.1F.4Test description  p. 1508
6.5.1F.4.1Initial conditions  p. 1508
6.5.1F.4.2Test procedure  p. 1509
6.5.1F.4.3Message contents  p. 1509
6.5.1F.5Test requirement  p. 1509
6.5.1GFrequency Error for V2X Communication  p. 1509
6.5.1G.1Frequency Error for V2X Communication / Non-concurrent with E-UTRA uplink transmission  p. 1509
6.5.1G.1.1Test purpose  p. 1509
6.5.1G.1.2Test applicability  p. 1509
6.5.1G.1.3Minimum Conformance Requirements  p. 1509
6.5.1G.1.4Test description  p. 1510
6.5.1G.1.4.1Initial condition  p. 1510
6.5.1G.1.4.2Test procedure  p. 1510
6.5.1G.1.4.3Message contents  p. 1511
6.5.1G.1.5Test requirement  p. 1511
6.5.1G.2Frequency error for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions  p. 1511
6.5.2Transmit modulation  p. 1513
6.5.2.1Error Vector Magnitude (EVM)  p. 1513
6.5.2.1.1Test Purpose  p. 1513
6.5.2.1.2Test applicability  p. 1513
6.5.2.1.3Minimum conformance requirements  p. 1513
6.5.2.1.4Test description  p. 1514
6.5.2.1.5Test requirement  p. 1518
6.5.2.1_1Error Vector Magnitude (EVM) for UL 64QAM  p. 1518
6.5.2.1_1.1Test Purpose  p. 1518
6.5.2.1_1.2Test applicability  p. 1518
6.5.2.1_1.3Minimum conformance requirements  p. 1519
6.5.2.1_1.4Test description  p. 1519
6.5.2.1_1.5Test requirement  p. 1520
6.5.2.1_2Error Vector Magnitude (EVM) for UL 256QAM  p. 1520
6.5.2.1_2.1Test Purpose  p. 1520
6.5.2.1_2.2Test applicability  p. 1521
6.5.2.1_2.3Minimum conformance requirements  p. 1521
6.5.2.1_2.4Test description  p. 1521
6.5.2.1_2.5Test requirement  p. 1522
6.5.2.1APUSCH-EVM with exclusion period  p. 1522
6.5.2.1A.1Test purpose  p. 1522
6.5.2.1A.2Test applicability  p. 1522
6.5.2.1A.3Minimum conformance requirement  p. 1523
6.5.2.1A.4Test description  p. 1523
6.5.2.1A.5Test requirement  p. 1524
6.5.2.1EError Vector Magnitude (EVM) for UE category 0  p. 1525
6.5.2.1E.1Error Vector Magnitude (EVM) for UE category 0  p. 1525
6.5.2.1E.2PUSCH-EVM with exclusion period for UE category 0  p. 1527
6.5.2.1EAError Vector Magnitude (EVM) for UE category M1  p. 1530
6.5.2.1EA.1Error Vector Magnitude (EVM) for UE category M1  p. 1530
6.5.2.1EA.2PUSCH-EVM with exclusion period for UE category M1  p. 1533
6.5.2.1EBError Vector Magnitude (EVM) for UE category 1bis  p. 1538
6.5.2.1EB.1Test purpose  p. 1538
6.5.2.1EB.2Test applicability  p. 1538
6.5.2.1EB.3Minimum conformance requirements  p. 1538
6.5.2.1EB.4Test description  p. 1538
6.5.2.1EB.5Test requirement  p. 1538
6.5.2.1ECError Vector Magnitude (EVM) for UE category M2  p. 1538
6.5.2.1EC.1Error Vector Magnitude (EVM) for UE category M2  p. 1538
6.5.2.1EC.2PUSCH-EVM with exclusion period for UE category M2  p. 1540
6.5.2.1F.1Error Vector Magnitude (EVM) for category NB1 and NB2  p. 1543
6.5.2.1F.1.4Test description  p. 1544
6.5.2.1F.1.5Test requirement  p. 1546
6.5.2.1GError Vector Magnitude (EVM) for V2X Communication  p. 1547
6.5.2.1G.0Minimum conformance requirements  p. 1547
6.5.2.1G.1Error Vector Magnitude (EVM) for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 1547
6.5.2.1G.1.1Test Purpose  p. 1547
6.5.2.1G.1.2Test applicability  p. 1547
6.5.2.1G.1.3Minimum conformance requirements  p. 1547
6.5.2.1G.1.4Test description  p. 1547
6.5.2.1G.1.4.1Initial conditions  p. 1547
6.5.2.1G.1.4.2Test procedure  p. 1548
6.5.2.1G.1.4.3Message contents  p. 1549
6.5.2.1G.1.5Test requirement  p. 1550
6.5.2.1G.2Error Vector Magnitude (EVM) for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions  p. 1550
6.5.2.1G.2.1Test Purpose  p. 1550
6.5.2.1G.2.2Test applicability  p. 1550
6.5.2.1G.2.3Minimum conformance requirements  p. 1550
6.5.2.1G.2.4Test description  p. 1551
6.5.2.1G.2.4.1Initial conditions  p. 1551
6.5.2.1G.2.4.2Test procedure  p. 1552
6.5.2.1G.2.4.3Message contents  p. 1553
6.5.2.1G.2.5Test requirement  p. 1554
6.5.2.1G.3Error Vector Magnitude (EVM) for V2X Communication / Intra-band contiguous multi-carrier operation  p. 1555
6.5.2.1G.3.1Test Purpose  p. 1555
6.5.2.1G.3.2Test applicability  p. 1555
6.5.2.1G.3.3Minimum conformance requirements  p. 1555
6.5.2.1G.3.4Test description  p. 1555
6.5.2.1G.3.4.1Initial conditions  p. 1555
6.5.2.1G.3.4.2Test procedure  p. 1556
6.5.2.1G.3.4.3Message contents  p. 1557
6.5.2.1G.3.5Test requirement  p. 1558
6.5.2.1_sError Vector Magnitude for subslot/slot TTI  p. 1558
6.5.2.2Carrier leakage  p. 1563
6.5.2.2.1Test Purpose  p. 1563
6.5.2.2.2Test applicability  p. 1563
6.5.2.2.3Minimum conformance requirements  p. 1563
6.5.2.2.4Test description  p. 1563
6.5.2.2.5Test requirement  p. 1565
6.5.2.2ECarrier leakage for UE category 0  p. 1565
6.5.2.2E.1Test Purpose  p. 1565
6.5.2.2E.2Test applicability  p. 1566
6.5.2.2E.3Minimum conformance requirements  p. 1566
6.5.2.2E.4Test description  p. 1566
6.5.2.2E.5Test requirement  p. 1566
6.5.2.2EACarrier leakage for UE category M1  p. 1567
6.5.2.2EA.1Test Purpose  p. 1567
6.5.2.2EA.2Test applicability  p. 1567
6.5.2.2EA.3Minimum conformance requirements  p. 1567
6.5.2.2EA.4Test description  p. 1567
6.5.2.2EA.5Test requirement  p. 1569
6.5.2.2EBCarrier leakage for UE category 1bis  p. 1569
6.5.2.2EB.1Test purpose  p. 1569
6.5.2.2EB.2Test applicability  p. 1569
6.5.2.2EB.3Minimum conformance requirements  p. 1569
6.5.2.2EB.4Test description  p. 1569
6.5.2.2EB.5Test requirement  p. 1570
6.5.2.2ECCarrier leakage for UE category M2  p. 1570
6.5.2.2EC.1Test Purpose  p. 1570
6.5.2.2EC.2Test applicability  p. 1570
6.5.2.2EC.3Minimum conformance requirements  p. 1570
6.5.2.2EC.4Test description  p. 1570
6.5.2.2FCarrier leakage for category NB1 and NB2  p. 1572
6.5.2.2F.4Test description  p. 1572
6.5.2.2F.5Test requirement  p. 1574
6.5.2.2GCarrier leakage for V2X Communication  p. 1574
6.5.2.2G.0Minimum conformance requirements  p. 1574
6.5.2.2G.1Carrier leakage for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 1574
6.5.2.2G.1.1Test Purpose  p. 1574
6.5.2.2G.1.2Test applicability  p. 1574
6.5.2.2G.1.3Minimum conformance requirements  p. 1575
6.5.2.2G.1.4Test description  p. 1575
6.5.2.2G.1.4.1 Initial conditions  p. 1575
6.5.2.2G.1.4.2Test procedure  p. 1575
6.5.2.2G.1.4.3Message contents  p. 1576
6.5.2.2G.1.5Test requirement  p. 1576
6.5.2.2G.2Carrier leakage for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmission  p. 1577
6.5.2.2G.2.1Test Purpose  p. 1577
6.5.2.2G.2.2Test applicability  p. 1577
6.5.2.2G.2.3Minimum conformance requirements  p. 1577
6.5.2.2G.2.4Test description  p. 1577
6.5.2.2G.2.4.1 Initial conditions  p. 1577
6.5.2.2G.2.4.2Test procedure  p. 1578
6.5.2.2G.2.4.3Message contents  p. 1578
6.5.2.2G.2.5Test requirement  p. 1579
6.5.2.2G.3Carrier leakage for V2X Communication / Intra-band contiguous MCC operation  p. 1579
6.5.2.2G.3.1Test Purpose  p. 1579
6.5.2.2G.3.2Test applicability  p. 1579
6.5.2.2G.3.3Minimum conformance requirements  p. 1579
6.5.2.2G.3.4Test description  p. 1579
6.5.2.2G.3.4.1 Initial conditions  p. 1579
6.5.2.2G.3.4.2Test procedure  p. 1580
6.5.2.2G.3.4.3Message contents  p. 1580
6.5.2.2G.3.5Test requirement  p. 1582
6.5.2.3In-band emissions for non allocated RB  p. 1582
6.5.2.3.1Test Purpose  p. 1582
6.5.2.3.2Test applicability  p. 1582
6.5.2.3.3Minimum conformance requirements  p. 1582
6.5.2.3.4Test description  p. 1584
6.5.2.3.5Test requirement  p. 1587
6.5.2.3EIn-band emissions for non allocated RB for UE category 0  p. 1588
6.5.2.3E.1Test Purpose  p. 1588
6.5.2.3E.2Test applicability  p. 1588
6.5.2.3E.3Minimum conformance requirements  p. 1588
6.5.2.3E.4Test description  p. 1589
6.5.2.3E.5Test requirement  p. 1589
6.5.2.3EAIn-band emissions for non allocated RB for UE category M1  p. 1590
6.5.2.3EA.1Test Purpose  p. 1590
6.5.2.3EA.2Test applicability  p. 1590
6.5.2.3EA.3Minimum conformance requirements  p. 1590
6.5.2.3EA.4Test description  p. 1593
6.5.2.3EA.5Test requirement  p. 1595
6.5.2.3EBIn-band emissions for non allocated RB for UE category 1bis  p. 1597
6.5.2.3EB.1Test purpose  p. 1597
6.5.2.3EB.2Test applicability  p. 1597
6.5.2.3EB.3Minimum conformance requirements  p. 1597
6.5.2.3EB.4Test description  p. 1597
6.5.2.3EB.5Test requirement  p. 1598
6.5.2.3ECIn-band emissions for non allocated RB for UE category M2  p. 1598
6.5.2.3EC.1Test Purpose  p. 1598
6.5.2.3EC.2Test applicability  p. 1599
6.5.2.3EC.3Minimum conformance requirements  p. 1599
6.5.2.3EC.4Test description  p. 1600
6.5.2.3EC.5Test requirement  p. 1602
6.5.2.3FIn-band emissions for non allocated RB for category NB1 and NB2  p. 1603
6.5.2.3F.4Test description  p. 1604
6.5.2.3F.4.1Initial conditions  p. 1604
6.5.2.3F.4.2Test procedure  p. 1605
6.5.2.3F.4.3Message contents  p. 1605
6.5.2.3F.5Test requirement  p. 1606
6.5.2.3GIn-band emissions for non-allocated RB for V2X Communication  p. 1607
6.5.2.3G.1In-band emissions for non-allocated RB for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 1607
6.5.2.3G.1.1Test Purpose  p. 1607
6.5.2.3G.1.2Test applicability  p. 1607
6.5.2.3G.1.3Minimum conformance requirements  p. 1607
6.5.2.3G.1.4Test description  p. 1609
6.5.2.3G.1.4.1Initial conditions  p. 1609
6.5.2.3G.1.4.2Test procedure  p. 1610
6.5.2.3G.1.4.3Message contents  p. 1611
6.5.2.3G.1.5Test requirement  p. 1613
6.5.2.3G.2In-band emissions for non-allocated RB for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions  p. 1614
6.5.2.3G.3In-band emissions for non-allocated RB for V2X Communication / Intra-band contiguous MCC operation  p. 1622
6.5.2.3G.3.2Test Applicability  p. 1622
6.5.2.3G.3.3Minimum conformance requirements  p. 1622
6.5.2.3G.3.4.3Message Contents  p. 1625
6.5.2.3G.3.5Test Requirement  p. 1625
6.5.2.4EVM equalizer spectrum flatness  p. 1628
6.5.2.4.1Test Purpose  p. 1628
6.5.2.4.2Test applicability  p. 1628
6.5.2.4.3Minimum conformance requirements  p. 1628
6.5.2.4.4Test description  p. 1629
6.5.2.4.5Test requirement  p. 1630
6.5.2.4EEVM equalizer spectrum flatness for UE category 0  p. 1631
6.5.2.4E.1Test Purpose  p. 1631
6.5.2.4E.2Test applicability  p. 1631
6.5.2.4E.3Minimum conformance requirements  p. 1631
6.5.2.4E.4Test description  p. 1631
6.5.2.4E.5Test requirement  p. 1632
6.5.2.4EAEVM equalizer spectrum flatness for UE category M1  p. 1633
6.5.2.4EA.1Test Purpose  p. 1633
6.5.2.4EA.2Test applicability  p. 1633
6.5.2.4EA.3Minimum conformance requirements  p. 1633
6.5.2.4EA.4Test description  p. 1633
6.5.2.4EA.5Test requirement  p. 1634
6.5.2.4EBEVM equalizer spectrum flatness for UE category 1bis  p. 1635
6.5.2.4EB.1Test purpose  p. 1635
6.5.2.4EB.2Test applicability  p. 1635
6.5.2.4EB.3Minimum conformance requirements  p. 1635
6.5.2.4EB.4Test description  p. 1636
6.5.2.4EB.5Test requirement  p. 1636
6.5.2.4ECEVM equalizer spectrum flatness for UE category M2  p. 1637
6.5.2.4EC.1Test Purpose  p. 1637
6.5.2.4EC.2Test applicability  p. 1637
6.5.2.4EC.3Minimum conformance requirements  p. 1637
6.5.2.4EC.4Test description  p. 1637
6.5.2.4EC.5Test requirement  p. 1638
6.5.2.4GEVM equalizer spectrum flatness for V2X transmission  p. 1638
6.5.2.4G.1EVM equalizer spectrum flatness for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 1638
6.5.2.4G.1.1Test Purpose  p. 1638
6.5.2.4G.1.2Test applicability  p. 1639
6.5.2.4G.1.3Minimum conformance requirements  p. 1639
6.5.2.4G.1.4Test description  p. 1640
6.5.2.4G.1.4.1Initial conditions  p. 1640
6.5.2.4G.1.4.2Test procedure  p. 1641
6.5.2.4G.1.4.3Message contents  p. 1641
6.5.2.4G.1.5Test requirement  p. 1643
6.5.2.4G.2Void  p. …
6.5.2.4G.3EVM equalizer spectrum flatness for V2X Communication / Intra-band contiguous multi-carrier operation  p. 1644
6.5.2.4G.3.2Test Applicability  p. 1644
6.5.2.4G.3.3Minimum conformance requirements  p. 1644
6.5.2.4G.3.4Test Description  p. 1644
6.5.2.4G.3.4.1Initial Conditions  p. 1644
6.5.2.4G.3.4.2Test Procedure  p. 1645
6.5.2.4G.3.4.3Message Contents  p. 1645
6.5.2.4G.3.5Test requirement  p. 1645
6.5.2ATransmit modulation for CA  p. 1646
6.5.2A.1Error Vector Magnitude (EVM) for CA  p. 1646
6.5.2A.1.0Minimum conformance requirements  p. 1646
6.5.2A.1.1Error Vector Magnitude (EVM) for CA (intra-band contiguous DL CA and UL CA)  p. 1647
6.5.2A.1.1_1EVM for CA (intra-band contiguous DL CA and UL CA) with UL 64QAM  p. 1650
6.5.2A.1.1_2EVM for CA (intra-band contiguous DL CA and UL CA) with UL 256QAM  p. 1651
6.5.2A.1.2Error Vector Magnitude (EVM) for CA (inter-band DL CA and UL CA)  p. 1653
6.5.2A.1.2_1Error Vector Magnitude (EVM) for CA (inter-band DL CA and UL CA) for UL 64QAM  p. 1658
6.5.2A.1.2_2Error Vector Magnitude (EVM) for CA (inter-band DL CA and UL CA) for UL 256QAM  p. 1661
6.5.2A.1.3Error Vector Magnitude (EVM) for CA (intra-band non-contiguous DL CA and UL CA)  p. 1663
6.5.2A.1.3_1Error Vector Magnitude (EVM) for CA (intra-band non-contiguous DL CA and UL CA) for UL 64QAM  p. 1665
6.5.2A.1.3_2Error Vector Magnitude (EVM) for CA (intra-band non-contiguous DL CA and UL CA) for UL 256QAM  p. 1668
6.5.2A.1.4Error Vector Magnitude (EVM) for CA (3UL CA)  p. 1670
6.5.2A.1.5Error Vector Magnitude (EVM) for CA (4UL CA)  p. 1674
6.5.2A.2Carrier leakage for CA  p. 1679
6.5.2A.2.0Minimum conformance requirements  p. 1679
6.5.2A.2.1Carrier leakage for CA (intra-band contiguous DL CA and UL CA)  p. 1680
6.5.2A.2.2Carrier leakage for CA (inter-band DL CA and UL CA)  p. 1682
6.5.2A.2.3Carrier leakage for CA (intra-band non-contiguous DL CA and UL CA)  p. 1685
6.5.2A.2.4Carrier leakage for CA (3UL CA)  p. 1687
6.5.2A.2.5Carrier leakage for CA (4UL CA)  p. 1691
6.5.2A.3In-band emissions for non allocated RB for CA  p. 1694
6.5.2A.3.0Minimum conformance requirements  p. 1694
6.5.2A.3.1In-band emissions for non allocated RB for CA (intra-band contiguous DL CA and UL CA)  p. 1696
6.5.2A.3.2In-band emissions for non allocated RB for CA (inter-band DL CA and UL CA)  p. 1702
6.5.2A.3.3In-band emissions for non allocated RB for CA (intra-band non-contiguous DL CA and UL CA)  p. 1707
6.5.2A.3.4In-band emissions for non allocated RB for CA (3UL CA)  p. 1710
6.5.2A.3.5In-band emissions for non allocated RB for CA (3UL CA)  p. 1716
6.5.2BTransmit modulation for UL- MIMO  p. 1722
6.5.2B.1Error Vector Magnitude (EVM) for UL- MIMO  p. 1722
6.5.2B.1.1Test Purpose  p. 1722
6.5.2B.1.2Test applicability  p. 1723
6.5.2B.1.3Minimum conformance requirements  p. 1723
6.5.2B.1.4Test description  p. 1723
6.5.2B.1.5Test requirement  p. 1725
6.5.2B.2Carrier leakage for UL-MIMO  p. 1726
6.5.2B.2.1Test Purpose  p. 1726
6.5.2B.2.2Test applicability  p. 1726
6.5.2B.2.3Minimum conformance requirements  p. 1726
6.5.2B.2.4Test description  p. 1726
6.5.2B.2.5Test requirement  p. 1727
6.5.2B.3In-band emissions for non allocated RB for UL-MIMO  p. 1728
6.5.2B.3.1Test Purpose  p. 1728
6.5.2B.3.2Test applicability  p. 1728
6.5.2B.3.3Minimum conformance requirements  p. 1728
6.5.2B.3.4Test description  p. 1729
6.5.2B.3.5Test requirement  p. 1731
6.5.2B.4EVM equalizer spectrum flatness for UL-MIMO  p. 1732
6.5.2B.4.1Test Purpose  p. 1732
6.5.2B.4.2Test applicability  p. 1732
6.5.2B.4.3Minimum conformance requirements  p. 1733
6.5.2B.4.4Test description  p. 1733
6.5.2B.4.5Test requirement  p. 1734
6.6Output RF spectrum emissions  p. 1735
6.6.1Occupied bandwidth  p. 1736
6.6.1.1Test purpose  p. 1736
6.6.1.2Test applicability  p. 1736
6.6.1.3Minimum conformance requirements  p. 1736
6.6.1.4Test description  p. 1736
6.6.1.4.1Initial conditions  p. 1736
6.6.1.4.2Test procedure  p. 1737
6.6.1.4.3Message contents  p. 1737
6.6.1.5Test requirement  p. 1737
6.6.1AOccupied bandwidth for CA  p. 1737
6.6.1A.0Minimum conformance requirements  p. 1737
6.6.1A.1Occupied bandwidth for CA (intra-band contiguous DL CA and UL CA)  p. 1738
6.6.1A.1.1Test purpose  p. 1738
6.6.1A.1.2Test applicability  p. 1738
6.6.1A.1.3Minimum conformance requirements  p. 1738
6.6.1A.1.4Test description  p. 1738
6.6.1A.1.5Test Requirements  p. 1740
6.6.1A.2Occupied bandwidth for CA (inter-band DL CA and UL CA)  p. 1740
6.6.1A.2.1Test purpose  p. 1740
6.6.1A.2.2Test applicability  p. 1740
6.6.1A.2.3Minimum conformance requirements  p. 1740
6.6.1A.2.4Test description  p. 1741
6.6.1A.2.5Test Requirements  p. 1743
6.6.1A.3Occupied bandwidth for CA (intra-band non-contiguous DL CA and UL CA)  p. 1743
6.6.1A.3.1Test purpose  p. 1743
6.6.1A.3.2Test applicability  p. 1743
6.6.1A.3.3Minimum conformance requirements  p. 1743
6.6.1A.3.4Test description  p. 1743
6.6.1A.3.5Test Requirements  p. 1745
6.6.1A.4Occupied bandwidth for CA (3DL CA and 3UL CA)  p. 1745
6.6.1A.4.1Test purpose  p. 1745
6.6.1A.4.2Test applicability  p. 1745
6.6.1A.4.3Minimum conformance requirements  p. 1745
6.6.1A.4.4Test description  p. 1745
6.6.1A.4.5Test Requirements  p. 1748
6.6.1A.5Occupied bandwidth for CA (4UL CA)  p. 1748
6.6.1A.5.1Test purpose  p. 1748
6.6.1A.5.2Test applicability  p. 1748
6.6.1A.5.3Minimum conformance requirements  p. 1748
6.6.1A.5.4Test description  p. 1748
6.6.1A.5.5Test Requirements  p. 1751
6.6.1BOccupied bandwidth for UL-MIMO  p. 1751
6.6.1B.1Test purpose  p. 1751
6.6.1B.2Test applicability  p. 1751
6.6.1B.3Minimum conformance requirements  p. 1751
6.6.1B.4Test description  p. 1752
6.6.1B.4.1Initial conditions  p. 1752
6.6.1B.4.2Test procedure  p. 1753
6.6.1B.4.3Message contents  p. 1753
6.6.1EOccupied bandwidth for UE category 0  p. 1753
6.6.1E.1Test purpose  p. 1753
6.6.1E.2Test applicability  p. 1753
6.6.1E.2aMinimum conformance requirements  p. 1753
6.6.1E.4Test description  p. 1754
6.6.1E.4.1Initial conditions  p. 1754
6.6.1E.4.2Test procedure  p. 1754
6.6.1E.4.3Message contents  p. 1754
6.6.1E.5Test requirement  p. 1754
6.6.1EAOccupied bandwidth for UE category M1  p. 1755
6.6.1EA.1Test purpose  p. 1755
6.6.1EA.2Test applicability  p. 1755
6.6.1EA.3Minimum conformance requirements  p. 1755
6.6.1EA.4Test description  p. 1755
6.6.1E.4A.1Initial conditions  p. 1755
6.6.1EA.4.2Test procedure  p. 1756
6.6.1EA.4.3Message contents  p. 1756
6.6.1EA.5Test requirement  p. 1756
6.6.1EBOccupied bandwidth for UE category 1bis  p. 1756
6.6.1EB.1Test purpose  p. 1756
6.6.1EB.2Test applicability  p. 1756
6.6.1EB.3Minimum conformance requirements  p. 1756
6.6.1EB.4Test description  p. 1757
6.6.1EB.4.1Initial conditions  p. 1757
6.6.1EB.4.2Test procedure  p. 1757
6.6.1EB.4.3Message contents  p. 1757
6.6.1EB.5Test requirement  p. 1757
6.6.1ECOccupied bandwidth for UE category M2  p. 1757
6.6.1EC.1Test purpose  p. 1757
6.6.1EC.2Test applicability  p. 1757
6.6.1EC.3Minimum conformance requirements  p. 1757
6.6.1EC.4Test description  p. 1757
6.6.1EC.4.1Initial conditions  p. 1757
6.6.1EC.4.2Test procedure  p. 1758
6.6.1EC.4.3Message contents  p. 1759
6.6.1EC.5Test requirement  p. 1759
6.6.1FOccupied bandwidth for category NB1 and NB2  p. 1759
6.6.1F.1Test purpose  p. 1759
6.6.1F.2Test applicability  p. 1759
6.6.1F.3Minimum conformance requirements  p. 1759
6.6.1F.4Test description  p. 1759
6.6.1F.4.1Initial conditions  p. 1759
6.6.1F.4.2Test procedure  p. 1760
6.6.1F.4.3Message contents  p. 1760
6.6.1F.5Test requirement  p. 1761
6.6.1GOccupied bandwidth for V2X Communication  p. 1761
6.6.1G.1Occupied bandwidth for V2X Communication / Non-concurrent with E-UTRA uplink transmission  p. 1761
6.6.1G.1.1Test purpose  p. 1761
6.6.1G.1.2Test applicability  p. 1761
6.6.1G.1.3Minimum conformance requirements  p. 1761
6.6.1G.1.4Test description  p. 1761
6.6.1G.1.4.1Initial conditions  p. 1761
6.6.1G.1.4.2Test procedure  p. 1762
6.6.1G.1.4.3Message contents  p. 1762
6.6.1G.1.5Test requirements  p. 1762
6.6.1G.2Occupied bandwidth for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions  p. 1762
6.6.1G.2.1Test purpose  p. 1762
6.6.1G.2.2Test applicability  p. 1762
6.6.1G.2.3Minimum conformance requirements  p. 1763
6.6.1G.2.4Test description  p. 1763
6.6.1G.2.4.1Initial conditions  p. 1763
6.6.1G.2.4.2Test procedure  p. 1763
6.6.1G.2.4.3Message contents  p. 1764
6.6.1G.2.5Test requirements  p. 1764
6.6.1G.3Occupied bandwidth for V2X Communication / Intra-band contiguous multi-carrier operation  p. 1764
6.6.1G.3.1Test purpose  p. 1764
6.6.1G.3.2Test applicability  p. 1764
6.6.1G.3.3Minimum conformance requirements  p. 1764
6.6.1G.3.4Test description  p. 1765
6.6.1G.3.4.1Initial conditions  p. 1765
6.6.1G.3.4.2Test procedure  p. 1765
6.6.1G.3.4.3Message contents  p. 1766
6.6.1G.3.5Test requirements  p. 1766
6.6.2Out of band emission  p. 1766
6.6.2.1Spectrum Emission Mask  p. 1766
6.6.2.1.1Test purpose  p. 1766
6.6.2.1.2Test applicability  p. 1766
6.6.2.1.3Minimum conformance requirements  p. 1766
6.6.2.1.4Test description  p. 1767
6.6.2.1.5Test requirements  p. 1769
6.6.2.1_1Spectrum Emission Mask for Multi-Cluster PUSCH  p. 1770
6.6.2.1_1.1Test purpose  p. 1770
6.6.2.1_1.2Test applicability  p. 1770
6.6.2.1_1.3Minimum conformance requirements  p. 1770
6.6.2.1_1.4Test description  p. 1771
6.6.2.1_1.5Test requirements  p. 1772
6.6.2.1ASpectrum emission mask for CA  p. 1773
6.6.2.1A.0Minimum conformance requirements  p. 1773
6.6.2.1A.1Spectrum emission mask for CA (intra-band contiguous DL CA and UL CA)  p. 1774
6.6.2.1A.2Spectrum emission mask for CA (inter-band DL CA and UL CA)  p. 1781
6.6.2.1A.3Spectrum emission mask for CA (intra-band non-contiguous DL CA and UL CA)  p. 1787
6.6.2.1A.4Spectrum emission mask for CA (3UL CA)  p. 1790
6.6.2.1A.5Spectrum Emission Mask for CA (4UL)  p. 1801
6.6.2.1BSpectrum Emission Mask for UL-MIMO  p. 1806
6.6.2.1B.1Test purpose  p. 1806
6.6.2.1B.2Test applicability  p. 1806
6.6.2.1B.3Minimum conformance requirements  p. 1806
6.6.2.1B.4Test description  p. 1806
6.6.2.1B.5Test requirements  p. 1808
6.6.2.1ESpectrum Emission Mask for UE category 0  p. 1809
6.6.2.1E.1Test purpose  p. 1809
6.6.2.1E.2Test applicability  p. 1809
6.6.2.1E.3Minimum conformance requirements  p. 1809
6.6.2.1E.4Test description  p. 1809
6.6.2.1E.5Test requirements  p. 1810
6.6.2.1EASpectrum Emission Mask for UE category M1  p. 1811
6.6.2.1EA.1Test purpose  p. 1811
6.6.2.1EA.2Test applicability  p. 1811
6.6.2.1EA.3Minimum conformance requirements  p. 1812
6.6.2.1EA.4Test description  p. 1812
6.6.2.1EA.5Test requirements  p. 1815
6.6.2.1EBSpectrum Emission Mask for UE category 1bis  p. 1816
6.6.2.1EB.1Test purpose  p. 1816
6.6.2.1EB.2Test applicability  p. 1816
6.6.2.1EB.3Minimum conformance requirements  p. 1816
6.6.2.1EB.4Test description  p. 1816
6.6.2.1EB.5Test requirements  p. 1817
6.6.2.1ECSpectrum Emission Mask for UE category M2  p. 1817
6.6.2.1EC.1Test purpose  p. 1817
6.6.2.1EC.2Test applicability  p. 1818
6.6.2.1EC.3Minimum conformance requirements  p. 1818
6.6.2.1EC.4Test description  p. 1818
6.6.2.1EC.5Test requirements  p. 1823
6.6.2.1FSpectrum Emission Mask for category NB1 and NB2  p. 1823
6.6.2.1F.4Test description  p. 1824
6.6.2.1F.5Test requirements  p. 1826
6.6.2.1GSpectrum Emission Mask for V2X Communication  p. 1826
6.6.2.1G.1Spectrum Emission Mask for V2X Communication Non-concurrent with E-UTRA uplink transmissions  p. 1826
6.6.2.1G.1.1Test purpose  p. 1826
6.6.2.1G.1.2Test applicability  p. 1826
6.6.2.1G.1.3Minimum conformance requirements  p. 1826
6.6.2.1G.1.4Test description  p. 1827
6.6.2.1G.1.4.1Initial conditions  p. 1827
6.6.2.1G.1.4.2Test procedure  p. 1828
6.6.2.1G.1.4.3Message contents  p. 1828
6.6.2.1G.1.5Test requirements  p. 1830
6.6.2.1G.2Spectrum Emission Mask for V2X Communication /Sidelink simultaneous with E-UTRA uplink transmissions  p. 1831
6.6.2.1G.2.1Test purpose  p. 1831
6.6.2.1G.2.2Test applicability  p. 1831
6.6.2.1G.2.3Minimum conformance requirements  p. 1831
6.6.2.1G.2.4Test description  p. 1831
6.6.2.1G.2.5Test requirements  p. 1833
6.6.2.1G.3Spectrum Emission Mask for V2X Communication / Intra-band contiguous MCC operation  p. 1834
6.6.2.1G.3.1Test purpose  p. 1834
6.6.2.1G.3.2Test Applicability  p. 1834
6.6.2.1G.3.3Minimum conformance requirements  p. 1835
6.6.2.1G.3.4Test Description  p. 1835
6.6.2.1G.3.4.1Initial conditions  p. 1835
6.6.2.1G.3.4.2Test procedure  p. 1835
6.6.2.1G.3.4.3Message Contents  p. 1836
6.6.2.1_sSpectrum Emission Mask for subslot/slot TTI  p. 1838
6.6.2.2Additional Spectrum Emission Mask  p. 1841
6.6.2.2.1Test purpose  p. 1841
6.6.2.2.2Test applicability  p. 1841
6.6.2.2.3Minimum conformance requirements  p. 1842
6.6.2.2.4Test description  p. 1844
6.6.2.2.5Test requirements  p. 1861
6.6.2.2_1Additional Spectrum Emission Mask for UL 64QAM  p. 1866
6.6.2.2_1.1Test purpose  p. 1866
6.6.2.2_1.2Test applicability  p. 1866
6.6.2.2_1.3Minimum conformance requirements  p. 1866
6.6.2.2_1.4Test description  p. 1866
6.6.2.2_1.5Test requirements  p. 1872
6.6.2.2_2Additional Spectrum Emission Mask for UL 256QAM  p. 1872
6.6.2.2_2.1Test purpose  p. 1872
6.6.2.2_2.2Test applicability  p. 1872
6.6.2.2_2.3Minimum conformance requirements  p. 1873
6.6.2.2_2.4Test description  p. 1873
6.6.2.2_2.5Test requirements  p. 1879
6.6.2.2_3Additional Spectrum Emission Mask with PUSCH frequency hopping  p. 1879
6.6.2.2AAdditional Spectrum Emission Mask for CA  p. 1885
6.6.2.2A.1Additional Spectrum Emission Mask for CA (intra-band contiguous DL CA and UL CA)  p. 1885
6.6.2.2A.1_1Additional Spectrum Emission Mask for CA (intra-band contiguous DL CA and UL CA) for UL 64QAM  p. 1888
6.6.2.2A.1_2Additional Spectrum Emission Mask for CA (intra-band contiguous DL CA and UL CA) for UL 256QAM  p. 1890
6.6.2.2A.2Additional Spectrum Emission Mask for CA (inter-band DL CA and UL CA)  p. 1891
6.6.2.2A.2_1Additional Spectrum Emission Mask for CA (inter-band DL CA and UL CA) for UL 64QAM  p. 1908
6.6.2.2A.2_2Additional Spectrum Emission Mask for CA (inter-band DL CA and UL CA) for UL 256QAM  p. 1918
6.6.2.2A.3Additional Spectrum Emission Mask for CA (intra-band non-contiguous DL CA and UL CA)  p. 1928
6.6.2.2A.4Additional Spectrum Emission Mask for CA (3UL CA)  p. 1932
6.6.2.2A.5Additional Spectrum Emission Mask for CA (4UL CA)  p. 1934
6.6.2.2BAdditional Spectrum Emission Mask for UL-MIMO  p. 1937
6.6.2.2B.1Test purpose  p. 1937
6.6.2.2B.2Test applicability  p. 1937
6.6.2.2B.3Minimum conformance requirements  p. 1937
6.6.2.2B.4Test description  p. 1937
6.6.2.2B.5Test requirements  p. 1946
6.6.2.2EAdditional Spectrum Emission Mask for UE category 0  p. 1946
6.6.2.2E.1Test purpose  p. 1946
6.6.2.2E.2Test applicability  p. 1947
6.6.2.2E.3Minimum conformance requirements  p. 1947
6.6.2.2E.4Test description  p. 1947
6.6.2.2E.5Test requirements  p. 1950
6.6.2.2EAAdditional Spectrum Emission Mask for UE category M1  p. 1954
6.6.2.2EA.1Test purpose  p. 1954
6.6.2.2EA.2Test applicability  p. 1954
6.6.2.2EA.3Minimum conformance requirements  p. 1954
6.6.2.2EA.4Test description  p. 1955
6.6.2.2EA.5Test requirements  p. 1960
6.6.2.2EBAdditional Spectrum Emission Mask for UE category 1bis  p. 1963
6.6.2.2EB.1Test purpose  p. 1963
6.6.2.2EB.2Test applicability  p. 1963
6.6.2.2EB.3Minimum conformance requirements  p. 1963
6.6.2.2EB.4Test description  p. 1963
6.6.2.2EB.5Test requirements  p. 1964
6.6.2.2ECAdditional Spectrum Emission Mask for UE category M2  p. 1968
6.6.2.2EC.1Test purpose  p. 1968
6.6.2.2EC.2Test applicability  p. 1968
6.6.2.2EC.3Minimum conformance requirements  p. 1968
6.6.2.2EC.4Test description  p. 1969
6.6.2.2EC.5Test requirements  p. 1972
6.6.2.2GAdditional Spectrum Emission Mask for V2X Communication  p. 1976
6.6.2.2G.0Minimum Requirements  p. 1976
6.6.2.2G.1Additional Spectrum Emission Mask for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 1977
6.6.2.2G.1.1Test purpose  p. 1977
6.6.2.2G.1.2Test applicability  p. 1977
6.6.2.2G.1.3Minimum conformance requirements  p. 1977
6.6.2.2G.1.4Test description  p. 1978
6.6.2.2G.1.4.1Initial conditions  p. 1978
6.6.2.2G.1.4.2Test procedure  p. 1978
6.6.2.2G.1.4.3Message contents  p. 1978
6.6.2.2G.1.5Test requirements  p. 1978
6.6.2.2G.2Additional Spectrum Emission Mask for V2X Communication / Sidelink simultaneous with E-UTRA uplink transmissions  p. 1979
6.6.2.2G.2.1Test purpose  p. 1979
6.6.2.2G.2.2Test applicability  p. 1979
6.6.2.2G.2.3Minimum conformance requirements  p. 1979
6.6.2.2G.2.4Test description  p. 1979
6.6.2.2G.2.4.1Initial conditions  p. 1979
6.6.2.2G.2.4.2Test procedure  p. 1980
6.6.2.2G.2.4.3Message contents  p. 1980
6.6.2.2G.2.5Test requirements  p. 1980
6.6.2.2_sAdditional Spectrum Emission Mask for subslot/slot TTI  p. 1982
6.6.2.3Adjacent Channel Leakage power Ratio  p. 2004
6.6.2.3.1Test purpose  p. 2004
6.6.2.3.2Test applicability  p. 2004
6.6.2.3.3Minimum conformance requirements  p. 2004
6.6.2.3.4Test description  p. 2005
6.6.2.3.5Test requirement  p. 2007
6.6.2.3_1Adjacent Channel Leakage power Ratio for HPUE  p. 2008
6.6.2.3_1.1Test purpose  p. 2008
6.6.2.3_1.2Test applicability  p. 2008
6.6.2.3_1.3Minimum conformance requirements  p. 2008
6.6.2.3_1.4Test description  p. 2010
6.6.2.3_1.5Test requirement  p. 2010
6.6.2.3_2Adjacent Channel Leakage power Ratio for Multi-Cluster PUSCH  p. 2011
6.6.2.3_2.1Test purpose  p. 2011
6.6.2.3_2.2Test applicability  p. 2011
6.6.2.3_2.3Minimum conformance requirements  p. 2011
6.6.2.3_2.4Test description  p. 2013
6.6.2.3_2.5Test requirement  p. 2014
6.6.2.3_3Adjacent Channel Leakage power Ratio for UL 64QAM  p. 2015
6.6.2.3_3.1Test purpose  p. 2015
6.6.2.3_3.2Test applicability  p. 2015
6.6.2.3_3.3Minimum conformance requirements  p. 2015
6.6.2.3_3.4Test description  p. 2015
6.6.2.3_3.5Test requirement  p. 2016
6.6.2.3_4Adjacent Channel Leakage power Ratio for Multi-Cluster PUSCH with UL 64QAM  p. 2017
6.6.2.3_4.1Test purpose  p. 2017
6.6.2.3_4.2Test applicability  p. 2018
6.6.2.3_4.3Minimum conformance requirements  p. 2018
6.6.2.3_4.4Test description  p. 2018
6.6.2.3_4.5Test requirement  p. 2019
6.6.2.3_5Adjacent Channel Leakage power Ratio for UL 256QAM  p. 2019
6.6.2.3_5.1Test purpose  p. 2019
6.6.2.3_5.2Test applicability  p. 2019
6.6.2.3_5.3Minimum conformance requirements  p. 2019
6.6.2.3_5.4Test description  p. 2019
6.6.2.3_5.5Test requirement  p. 2020
6.6.2.3_6Adjacent Channel Leakage power Ratio for Multi-Cluster PUSCH with UL 256QAM  p. 2021
6.6.2.3_6.1Test purpose  p. 2021
6.6.2.3_6.2Test applicability  p. 2021
6.6.2.3_6.3Minimum conformance requirements  p. 2021
6.6.2.3_6.4Test description  p. 2022
6.6.2.3_6.5Test requirement  p. 2023
6.6.2.3AAdjacent Channel Leakage power Ratio for CA  p. 2023
6.6.2.3A.0Minimum conformance requirements  p. 2023
6.6.2.3A.0.1Minimum requirement UTRA for CA  p. 2023
6.6.2.3A.0.2Minimum requirements for CA E-UTRA  p. 2025
6.6.2.3A.1Adjacent Channel Leakage power Ratio for CA (intra-band contiguous DL CA and UL CA)  p. 2026
6.6.2.3A.1_1Adjacent Channel Leakage power Ratio for CA (intra-band contiguous DL CA and UL CA) for UL 64QAM  p. 2031
6.6.2.3A.1_2Adjacent Channel Leakage power Ratio for CA (intra-band contiguous DL CA and UL CA) for UL 256QAM  p. 2035
6.6.2.3A.1_3Adjacent Channel Leakage power Ratio for CA (intra-band contiguous DL CA and UL CA) for HPUE  p. 2037
6.6.2.3A.2Adjacent Channel Leakage power Ratio for CA (inter-band DL CA and UL CA)  p. 2041
6.6.2.3A.2_1Adjacent Channel Leakage power Ratio for CA (inter-band DL CA and UL CA) for UL 64QAM  p. 2048
6.6.2.3A.2_2Adjacent Channel Leakage power Ratio for CA (inter-band DL CA and UL CA) for UL 256QAM  p. 2050
6.6.2.3A.3Adjacent Channel Leakage power Ratio for CA (intra-band non-contiguous DL CA and UL CA)  p. 2052
6.6.2.3A.3.1Test purpose  p. 2052
6.6.2.3A.3_1Adjacent Channel Leakage power Ratio for CA (intra-band non-contiguous DL CA and UL CA) for UL 64QAM  p. 2055
6.6.2.3A.3_2Adjacent Channel Leakage power Ratio for CA (intra-band non-contiguous DL CA and UL CA) for UL 256QAM  p. 2057
6.6.2.3A.4Adjacent Channel Leakage power Ratio for CA (3UL CA)  p. 2058
6.6.2.3A.5Adjacent Channel Leakage power Ratio for CA (4UL CA)  p. 2067
6.6.2.3BAdjacent Channel Leakage power Ratio for UL-MIMO  p. 2070
6.6.2.3B.1Test purpose  p. 2070
6.6.2.3B.2Test applicability  p. 2070
6.6.2.3B.3Minimum conformance requirements  p. 2070
6.6.2.3B.4Test description  p. 2072
6.6.2.3B.5Test requirement  p. 2074
6.6.2.3EAdjacent Channel Leakage power Ratio for UE category 0  p. 2075
6.6.2.3E.1Test purpose  p. 2075
6.6.2.3E.2Test applicability  p. 2075
6.6.2.3E.3Minimum conformance requirements  p. 2075
6.6.2.3E.4Test description  p. 2075
6.6.2.3E.5Test requirement  p. 2076
6.6.2.3EAAdjacent Channel Leakage power Ratio for UE category M1  p. 2077
6.6.2.3EA.1Test purpose  p. 2077
6.6.2.3EA.2Test applicability  p. 2077
6.6.2.3EA.3Minimum conformance requirements  p. 2078
6.6.2.3EA.4Test description  p. 2079
6.6.2.3EA.5Test requirement  p. 2082
6.6.2.3EBAdjacent Channel Leakage power Ratio for UE category 1bis  p. 2083
6.6.2.3EB.1Test purpose  p. 2083
6.6.2.3EB.2Test applicability  p. 2083
6.6.2.3EB.3Minimum conformance requirements  p. 2083
6.6.2.3EB.4Test description  p. 2083
6.6.2.3EB.5Test requirement  p. 2084
6.6.2.3ECAdjacent Channel Leakage power Ratio for UE category M2  p. 2085
6.6.2.3EC.1Test purpose  p. 2085
6.6.2.3EC.2Test applicability  p. 2085
6.6.2.3EC.3Minimum conformance requirements  p. 2085
6.6.2.3EC.4Test description  p. 2086
6.6.2.3EC.5Test requirement  p. 2091
6.6.2.3FAdjacent Channel Leakage power Ratio for category NB1 and NB2  p. 2092
6.6.2.3F.4Test description  p. 2093
6.6.2.3F.5Test requirement  p. 2094
6.6.2.3FAAdjacent Channel Leakage power Ratio for category NB1 and NB2/Power Class 6  p. 2095
6.6.2.3FA.1Test purpose  p. 2095
6.6.2.3FA.2Test applicability  p. 2095
6.6.2.3FA.3Minimum conformance requirements  p. 2095
6.6.2.3FA.4Test description  p. 2095
6.6.2.3FA.5Test requirement  p. 2096
6.6.2.3GAdjacent Channel Leakage power Ratio for V2X Communication  p. 2097
6.6.2.3G.1Adjacent Channel Leakage power Ratio for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 2097
6.6.2.3G.1.1Test purpose  p. 2097
6.6.2.3G.1.2Test applicability  p. 2097
6.6.2.3G.1.3Minimum conformance requirements  p. 2097
6.6.2.3G.1.4Test description  p. 2097
6.6.2.3G.1.4.1Initial conditions  p. 2097
6.6.2.3G.1.4.2Test procedure  p. 2098
6.6.2.3G.1.4.3Message contents  p. 2098
6.6.2.3G.1.5Test requirements  p. 2099
6.6.2.3G.2Adjacent Channel Leakage power Ratio for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions  p. 2099
6.6.2.3G.2.1Test purpose  p. 2099
6.6.2.3G.2.2Test applicability  p. 2099
6.6.2.3G.2.3Minimum conformance requirements  p. 2099
6.6.2.3G.2.4Test description  p. 2100
6.6.2.3G.2.4.1Initial conditions  p. 2100
6.6.2.3G.2.4.2Test procedure  p. 2101
6.6.2.3G.2.4.3Message contents  p. 2102
6.6.2.3G.2.5Test requirements  p. 2102
6.6.2.3G.3Adjacent Channel Leakage power Ratio for V2X Communication / Intra-band contiguous multi-carrier operation  p. 2103
6.6.2.3G.3.1Test purpose  p. 2103
6.6.2.3G.3.2Test applicability  p. 2103
6.6.2.3G.3.3Minimum conformance requirements  p. 2103
6.6.2.3G.3.4Test description  p. 2103
6.6.2.3G.3.4.1Initial conditions  p. 2103
6.6.2.3G.3.4.2Test procedure  p. 2104
6.6.2.3G.3.4.3Message contents  p. 2104
6.6.2.3G.3.5Test requirements  p. 2104
6.6.2.3_sAdjacent Channel Leakage power Ratio for subslot/slot TTI  p. 2105
6.6.2.4Void  p. …
6.6.3Spurious emissions  p. 2110
6.6.3.1Transmitter Spurious emissions  p. 2110
6.6.3.1.1Test purpose  p. 2110
6.6.3.1.2Test applicability  p. 2110
6.6.3.1.3Minimum conformance requirements  p. 2110
6.6.3.1.4Test description  p. 2111
6.6.3.1.5Test requirement  p. 2112
6.6.3.1_1Transmitter Spurious emissions for Multi-Cluster PUSCH  p. 2113
6.6.3.1_1.1Test purpose  p. 2113
6.6.3.1_1.2Test applicability  p. 2113
6.6.3.1_1.3Minimum conformance requirements  p. 2113
6.6.3.1_1.4Test description  p. 2114
6.6.3.1_1.5Test requirement  p. 2115
6.6.3.1ATransmitter Spurious emissions for CA  p. 2116
6.6.3.1A.0Minimum conformance requirements  p. 2116
6.6.3.1A.1Transmitter Spurious emissions for CA (intra-band contiguous DL CA and UL CA)  p. 2117
6.6.3.1A.2Transmitter Spurious emissions for CA (inter-band DL CA and UL CA)  p. 2121
6.6.3.1A.3Transmitter Spurious emissions for CA (intra-band non-contiguous DL CA and UL CA)  p. 2134
6.6.3.1A.4Transmitter Spurious emissions for CA (3UL CA)  p. 2136
6.6.3.1A.4.1Transmitter Spurious emissions for CA (intra-band contiguous 3DL CA and 3UL CA)  p. 2136
6.6.3.1A.4.1.1Test purpose  p. 2136
6.6.3.1A.4.1.2Test applicability  p. 2136
6.6.3.1A.4.1.3Minimum conformance requirements  p. 2136
6.6.3.1A.4.1.4Test description  p. 2136
6.6.3.1A.4.1.4.1Initial conditions  p. 2136
6.6.3.1A.4.1.4.2Test procedure  p. 2138
6.6.3.1A.4.1.4.3Message contents  p. 2138
6.6.3.1A.4.1.5Test Requirements  p. 2138
6.6.3.1A.4.2Transmitter Spurious emissions for CA (inter-band 3DL CA and 3UL CA)  p. 2138
6.6.3.1A.4.2.1Test purpose  p. 2138
6.6.3.1A.4.2.2Test applicability  p. 2139
6.6.3.1A.4.2.3Minimum conformance requirements  p. 2139
6.6.3.1A.4.2.4Test description  p. 2139
6.6.3.1A.4.2.4.1Initial conditions  p. 2139
6.6.3.1A.4.2.4.2Test procedure  p. 2142
6.6.3.1A.4.2.4.3Message contents  p. 2143
6.6.3.1A.4.2.5Test Requirements  p. 2143
6.6.3.1A.4.3Transmitter Spurious emissions for CA (3UL CA) (intra-band non-contiguous 3DL CA and 3UL CA)  p. 2143
6.6.3.1A.4.3.1Test purpose  p. 2143
6.6.3.1A.4.3.2Test applicability  p. 2143
6.6.3.1A.4.3.3Minimum conformance requirements  p. 2143
6.6.3.1A.4.3.4Test description  p. 2143
6.6.3.1A.4.3.4.1Initial conditions  p. 2143
6.6.3.1A.4.3.4.2Test procedure  p. 2144
6.6.3.1A.4.3.4.3Message contents  p. 2145
6.6.3.1A.4.3.5Test requirement  p. 2145
6.6.3.1A.5Transmitter Spurious emissions for CA (4UL CA)  p. 2145
6.6.3.2Spurious emission band UE co-existence  p. 2147
6.6.3.2.1Test purpose  p. 2147
6.6.3.2.2Test applicability  p. 2147
6.6.3.2.3Minimum conformance requirements  p. 2147
6.6.3.2.4Test description  p. 2219
6.6.3.2.5Test requirement  p. 2224
6.6.3.2_1Void  p. …
6.6.3.2ASpurious emission band UE co-existence for CA  p. 2229
6.6.3.2A.0Minimum conformance requirements  p. 2229
6.6.3.2A.1Spurious emission band UE co-existence for CA (intra-band contiguous DL CA and UL CA)  p. 2288
6.6.3.2A.2Spurious emission band UE co-existence for CA (inter-band DL CA and UL CA)  p. 2291
6.6.3.2A.3Spurious emission band UE co-existence for CA (intra-band non-contiguous DL CA and UL CA)  p. 2308
6.6.3.2A.4Spurious emission band UE co-existence for CA (3UL CA)  p. 2310
6.6.3.2A.5Spurious emission band UE co-existence for CA (4UL CA)  p. 2313
6.6.3.3Additional spurious emissions  p. 2314
6.6.3.3.1Test purpose  p. 2315
6.6.3.3.2Test applicability  p. 2315
6.6.3.3.3Minimum conformance requirements  p. 2315
6.6.3.3.4Test description  p. 2327
6.6.3.3.5Test requirement  p. 2374
6.6.3.3_1Additional spurious emissions for UL 64QAM  p. 2385
6.6.3.3_1.1Test purpose  p. 2385
6.6.3.3_1.2Test applicability  p. 2386
6.6.3.3_1.3Minimum conformance requirements  p. 2386
6.6.3.3_1.4Test description  p. 2386
6.6.3.3_1.5Test requirement  p. 2402
6.6.3.3_2Additional spurious emissions for UL 256QAM  p. 2402
6.6.3.3_2.1Test purpose  p. 2402
6.6.3.3_2.2Test applicability  p. 2402
6.6.3.3_2.3Minimum conformance requirements  p. 2403
6.6.3.3_2.4Test description  p. 2403
6.6.3.3_2.5Test requirement  p. 2416
6.6.3.3AAdditional spurious emissions for CA  p. 2416
6.6.3.3A.1Additional spurious emissions for CA (intra-band contiguous DL CA and UL CA)  p. 2416
6.6.3.3A.1.4Test description  p. 2419
6.6.3.3A.1.4.1Initial conditions  p. 2419
6.6.3.3A.1.4.2Test procedure  p. 2424
6.6.3.3A.1.4.3Message contents  p. 2425
6.6.3.3A.1.5Test requirement  p. 2426
6.6.3.3A.1_1Additional spurious emissions for CA (intra-band contiguous DL CA and UL CA) for UL 64QAM  p. 2429
6.6.3.3A.1_1.4Test description  p. 2430
6.6.3.3A.1_1.4.1Initial conditions  p. 2430
6.6.3.3A.1_1.4.2Test procedure  p. 2434
6.6.3.3A.1_1.4.3Message contents  p. 2435
6.6.3.3A.1_1.5Test requirement  p. 2435
6.6.3.3A.1_2Additional spurious emissions for CA (intra-band contiguous DL CA and UL CA) for UL 256QAM  p. 2435
6.6.3.3A.1_2.4Test description  p. 2435
6.6.3.3A.1_2.4.1Initial conditions  p. 2435
6.6.3.3A.1_2.4.2Test procedure  p. 2439
6.6.3.3A.1_2.4.3Message contents  p. 2439
6.6.3.3A.1_2.5Test requirement  p. 2440
6.6.3.3A.2Additional spurious emissions for CA (inter-band DL CA and UL CA)  p. 2440
6.6.3.3A.2.4Test description  p. 2440
6.6.3.3A.2.4.1Initial conditions  p. 2440
6.6.3.3A.2.4.2Test procedures  p. 2451
6.6.3.3A.2.4.3Message contents  p. 2451
6.6.3.3A.2.5Test requirement  p. 2451
6.6.3.3A.2_1Additional spurious emissions for CA (inter-band DL CA and UL CA) for UL 64QAM  p. 2451
6.6.3.3A.2_1.4Test description  p. 2452
6.6.3.3A.2_1.4.1Initial conditions  p. 2452
6.6.3.3A.2_1.4.2Test procedures  p. 2459
6.6.3.3A.2_1.4.3Message contents  p. 2459
6.6.3.3A.2_1.5Test requirement  p. 2459
6.6.3.3A.2_2Additional spurious emissions for CA (inter-band DL CA and UL CA) for UL 256QAM  p. 2459
6.6.3.3A.2_2.4Test description  p. 2459
6.6.3.3A.2_2.4.1Initial conditions  p. 2459
6.6.3.3A.2_2.4.2Test procedures  p. 2462
6.6.3.3A.2_2.4.3Message contents  p. 2463
6.6.3.3A.2_2.5Test requirement  p. 2463
6.6.3.3A.3-  p. 2463
6.6.3.3A.4Additional spurious emissions for CA (3UL CA)  p. 2463
6.6.3.3A.5Additional spurious emissions for CA (4UL CA)  p. 2466
6.6.3.3A.5.4Test description  p. 2466
6.6.3.3A.5.4.1Initial conditions  p. 2466
6.6.3.3A.5.4.2Test procedure  p. 2467
6.6.3.3A.5.4.3Message contents  p. 2468
6.6.3.3A.5.5Test requirement  p. 2468
6.6.3BSpurious emission for UL-MIMO  p. 2468
6.6.3B.1Transmitter Spurious emissions for UL-MIMO  p. 2468
6.6.3B.1.1Test purpose  p. 2468
6.6.3B.1.2Test applicability  p. 2468
6.6.3B.1.3Minimum conformance requirements  p. 2468
6.6.3B.1.4Test description  p. 2468
6.6.3B.1.5Test requirement  p. 2470
6.6.3B.2Spurious emission band UE co-existence for UL-MIMO  p. 2470
6.6.3B.2.1Test purpose  p. 2470
6.6.3B.2.2Test applicability  p. 2470
6.6.3B.2.3Minimum conformance requirements  p. 2470
6.6.3B.2.4Test description  p. 2470
6.6.3B.2.5Test requirement  p. 2472
6.6.3B.3Additional spurious emissions for UL-MIMO  p. 2477
6.6.3B.3.1Test purpose  p. 2477
6.6.3B.3.2Test applicability  p. 2477
6.6.3B.3.3Minimum conformance requirements  p. 2477
6.6.3B.3.4Test description  p. 2477
6.6.3B.3.5Test requirement  p. 2507
6.6.3ESpurious emission for UE category 0  p. 2507
6.6.3E.1Transmitter Spurious emissions for UE category 0  p. 2507
6.6.3E.1.1Test purpose  p. 2507
6.6.3E.1.2Test applicability  p. 2507
6.6.3E.1.3Minimum conformance requirements  p. 2507
6.6.3E.1.4Test description  p. 2507
6.6.3E.1.5Test requirement  p. 2508
6.6.3E.2Spurious emission band UE co-existence for UE category 0  p. 2509
6.6.3E.2.1Test purpose  p. 2509
6.6.3E.2.2Test applicability  p. 2509
6.6.3E.2.3Minimum conformance requirements  p. 2509
6.6.3E.2.4Test description  p. 2537
6.6.3E.2.5Test requirement  p. 2540
6.6.3E.3Additional spurious emissions for UE category 0  p. 2541
6.6.3E.3.1Test purpose  p. 2541
6.6.3E.3.2Test applicability  p. 2541
6.6.3E.3.3Minimum conformance requirements  p. 2542
6.6.3E.3.4Test description  p. 2542
6.6.3E.3.5Test requirement  p. 2543
6.6.3EASpurious emission for UE category M1  p. 2544
6.6.3EA.1Transmitter Spurious emissions for UE category M1  p. 2544
6.6.3EA.1.1Test purpose  p. 2544
6.6.3EA.1.2Test applicability  p. 2544
6.6.3EA.1.3Minimum conformance requirements  p. 2544
6.6.3EA.1.4Test description  p. 2544
6.6.3EA.1.5Test requirement  p. 2546
6.6.3EA.2Spurious emission band UE co-existence for UE category M1  p. 2546
6.6.3EA.2.1Test purpose  p. 2546
6.6.3EA.2.2Test applicability  p. 2546
6.6.3EA.2.3Minimum conformance requirements  p. 2546
6.6.3EA.2.4Test description  p. 2589
6.6.3EA.2.5Test requirement  p. 2593
6.6.3EA.3Additional spurious emissions for UE category M1  p. 2595
6.6.3EA.3.1Test purpose  p. 2595
6.6.3EA.3.2Test applicability  p. 2595
6.6.3EA.3.3Minimum conformance requirements  p. 2595
6.6.3EA.3.4Test description  p. 2599
6.6.3EA.3.5Test requirement  p. 2612
6.6.3EBSpurious emission for UE category 1bis  p. 2613
6.6.3EB.1Transmitter Spurious emissions for UE category 1bis  p. 2613
6.6.3EB.1.1Test purpose  p. 2613
6.6.3EB.1.2Test applicability  p. 2613
6.6.3EB.1.3Minimum conformance requirements  p. 2613
6.6.3EB.1.4Test description  p. 2613
6.6.3EB.1.5Test requirement  p. 2614
6.6.3EB.2Spurious emission band UE co-existence for UE category 1bis  p. 2614
6.6.3EB.2.1Test purpose  p. 2614
6.6.3EB.2.2Test applicability  p. 2614
6.6.3EB.2.3Minimum conformance requirements  p. 2614
6.6.3EB.2.4Test description  p. 2614
6.6.3EB.2.5Test requirement  p. 2615
6.6.3EB.3Additional spurious emissions for UE category 1bis  p. 2615
6.6.3EB.3.1Test purpose  p. 2615
6.6.3EB.3.2Test applicability  p. 2615
6.6.3EB.3.3Minimum conformance requirements  p. 2615
6.6.3EB.3.4Test description  p. 2615
6.6.3EB.3.5Test requirement  p. 2615
6.6.3ECSpurious emission for UE category M2  p. 2620
6.6.3EC.1Transmitter Spurious emissions for UE category M2  p. 2620
6.6.3EC.1.1Test purpose  p. 2620
6.6.3EC.1.2Test applicability  p. 2620
6.6.3EC.1.3Minimum conformance requirements  p. 2620
6.6.3EC.1.4Test description  p. 2620
6.6.3EC.1.5Test requirement  p. 2622
6.6.3EC.2Spurious emission band UE co-existence for UE category M2  p. 2622
6.6.3EC.2.1Test purpose  p. 2622
6.6.3EC.2.2Test applicability  p. 2622
6.6.3EC.2.3Minimum conformance requirements  p. 2623
6.6.3EC.2.4Test description  p. 2663
6.6.3EC.2.5Test requirement  p. 2666
6.6.3EC.3Additional spurious emissions for UE category M2  p. 2670
6.6.3FSpurious emission for category NB1 and NB2  p. 2675
6.6.3F.1Transmitter Spurious emissions for category NB1 and NB2  p. 2675
6.6.3F.1.4Test description  p. 2676
6.6.3F.1.5Test requirement  p. 2677
6.6.3F.2Spurious emission band UE co-existence for category NB1 and NB2  p. 2677
6.6.3F.2.4Test description  p. 2728
6.6.3F.2.5Test requirement  p. 2730
6.6.3GTransmitter Spurious emissions for V2X  p. 2732
6.6.3G.1Transmitter Spurious emissions for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 2732
6.6.3G.1.1Test purpose  p. 2732
6.6.3G.1.2Test applicability  p. 2732
6.6.3G.1.3Minimum conformance requirements  p. 2732
6.6.3G.1.4Test description  p. 2732
6.6.3G.1.4.1Initial conditions  p. 2732
6.6.3G.1.4.2Test procedure  p. 2733
6.6.3G.1.4.3Message contents  p. 2733
6.6.3G.1.5Test requirement  p. 2735
6.6.3G.1_1Spurious emission band UE co-existence for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 2735
6.6.3G.1_1.1Test purpose  p. 2735
6.6.3G.1_1.2Test applicability  p. 2736
6.6.3G.1_1.3Minimum conformance requirements  p. 2736
6.6.3G.1_1.4Test description  p. 2740
6.6.3G.1_1.4.1Initial conditions  p. 2740
6.6.3G.1_1.4.2Test procedure  p. 2741
6.6.3G.1_1.4.3Message contents  p. 2742
6.6.3G.1_1.5Test requirement  p. 2742
6.6.3G.2Spurious emission for V2X Communication / Sidelink simultaneous with E-UTRA uplink transmissions  p. 2743
6.6.3G.2.1Test purpose  p. 2743
6.6.3G.2.2Test applicability  p. 2743
6.6.3G.2.3Minimum conformance requirements  p. 2743
6.6.3G.2.4Test description  p. 2743
6.6.3G.2.4.1Initial conditions  p. 2743
6.6.3G.2.4.2Test procedure  p. 2747
6.6.3G.2.4.3Message contents  p. 2747
6.6.3G.2.5Test requirement  p. 2747
6.6.3G.2_1Spurious emission band UE co-existence for V2X Communication / Sidelink simultaneous with E-UTRA uplink transmissions  p. 2751
6.6.3G.2_1.1Test purpose  p. 2751
6.6.3G.2_1.2Test applicability  p. 2751
6.6.3G.2_1.3Minimum conformance requirements  p. 2751
6.6.3G.2_1.4Test description  p. 2753
6.6.3G.2_1.4.1Initial conditions  p. 2753
6.6.3G.2_1.4.2Test procedure  p. 2756
6.6.3G.2_1.4.3Message contents  p. 2756
6.6.3G.2_1.5Test requirement  p. 2756
6.6.3G.2_2Additional Spurious emission band UE co-existence for V2X Communication / Sidelink simultaneous with E-UTRA uplink transmissions  p. 2758
6.6.3G.3Spurious emission for V2X Communication / Intra-band contiguous MCC operation  p. 2758
6.6.3G.3.1Test purpose  p. 2758
6.6.3G.3.2Test applicability  p. 2758
6.6.3G.3.3Minimum conformance requirements  p. 2758
6.6.3G.3.4Test description  p. 2759
6.6.3G.3.4.1Initial conditions  p. 2759
6.6.3G.3.4.2Test procedure  p. 2759
6.6.3G.3.4.3Message contents  p. 2759
6.6.3G.3.5Test requirement  p. 2761
6.6.3G.3_1Spurious emission band UE co-existence for V2X Communication / Intra-band contiguous MCC operation  p. 2761
6.6.3G.3_1.1Test purpose  p. 2761
6.6.3G.3_1.2Test Applicability  p. 2761
6.6.3G.3_1.3Minimum conformance requirements  p. 2761
6.6.3G.3_1.4Test Description  p. 2762
6.6.3G.3_1.4.1Initial conditions  p. 2762
6.6.3G.3_1.4.2Test procedure  p. 2763
6.6.3G.3_1.4.3Message contents  p. 2763
6.6.3G.3_1.5Test requirement  p. 2763
6.7Transmit intermodulation  p. 2763
6.7.1Test purpose  p. 2763
6.7.2Test applicability  p. 2763
6.7.3Minimum conformance requirements  p. 2763
6.7.4Test description  p. 2764
6.7.4.1Initial conditions  p. 2764
6.7.4.2Test procedure  p. 2764
6.7.4.3Message contents  p. 2765
6.7.5Test requirement  p. 2765
6.7ATransmit intermodulation for CA  p. 2765
6.7A.0Minimum conformance requirements  p. 2765
6.7A.1Transmit intermodulation for CA (intra-band contiguous DL CA and UL CA)  p. 2766
6.7A.1.1Test purpose  p. 2766
6.7A.1.2Test applicability  p. 2766
6.7A.1.3Minimum conformance requirements  p. 2766
6.7A.1.4Test description  p. 2766
6.7A.1.4.1Initial conditions  p. 2766
6.7A.1.4.2Test procedure  p. 2767
6.7A.1.4.3Message contents  p. 2768
6.7A.1.5Test requirement  p. 2768
6.7A.2Transmit intermodulation for CA (inter-band DL CA and UL CA)  p. 2768
6.7A.2.1Test purpose  p. 2768
6.7A.2.2Test applicability  p. 2769
6.7A.2.3Minimum conformance requirements  p. 2769
6.7A.2.4Test description  p. 2769
6.7A.2.4.1Initial conditions  p. 2769
6.7A.2.4.2Test procedure  p. 2770
6.7A.2.4.3Message contents  p. 2771
6.7A.2.5Test requirement  p. 2771
6.7A.3-  p. 2772
6.7A.4Transmit intermodulation for CA (3DL CA and 3UL CA)  p. 2772
6.7A.4.1Test purpose  p. 2772
6.7A.4.2Test applicability  p. 2772
6.7A.4.3Minimum conformance requirements  p. 2772
6.7A.4.4Test description  p. 2772
6.7A.4.4.1Initial conditions  p. 2772
6.7A.4.4.2Test procedure  p. 2774
6.7A.4.4.3Message contents  p. 2775
6.7A.4.5Test requirement  p. 2775
6.7A.5Transmit intermodulation for CA (4UL CA)  p. 2776
6.7BTransmit intermodulation for UL-MIMO  p. 2779
6.7B.1Test purpose  p. 2779
6.7B.2Test applicability  p. 2779
6.7B.3Minimum conformance requirements  p. 2779
6.7B.4Test description  p. 2779
6.7B.4.1Initial conditions  p. 2779
6.7B.4.2Test procedure  p. 2780
6.7B.4.3Message contents  p. 2781
6.7ETransmit intermodulation for UE category 0  p. 2781
6.7E.1Test purpose  p. 2781
6.7E.2Test applicability  p. 2781
6.7E.3Minimum conformance requirements  p. 2781
6.7E.4Test description  p. 2781
6.7E.4.1Initial conditions  p. 2781
6.7E.4.2Test procedure  p. 2781
6.7E.4.3Message contents  p. 2781
6.7E.5Test requirement  p. 2781
6.7EATransmit intermodulation for UE category M1  p. 2782
6.7EA.1Test purpose  p. 2782
6.7EA.2Test applicability  p. 2782
6.7EA.3Minimum conformance requirements  p. 2782
6.7EA.4Test description  p. 2783
6.7EA.4.1Initial conditions  p. 2783
6.7EA.4.2Test procedure  p. 2783
6.7EA.4.3Message contents  p. 2784
6.7EA.5Test requirement  p. 2784
6.7EBTransmit intermodulation for UE category 1bis  p. 2784
6.7EB.1Test purpose  p. 2784
6.7EB.2Test applicability  p. 2784
6.7EB.3Minimum conformance requirements  p. 2784
6.7EB.4Test description  p. 2784
6.7EB.4.1Initial conditions  p. 2784
6.7EB.4.2Test procedure  p. 2785
6.7EB.4.3Message contents  p. 2785
6.7EB.5Test requirement  p. 2785
6.7ECTransmit intermodulation for UE category M2  p. 2785
6.7EC.1Test purpose  p. 2785
6.7EC.2Test applicability  p. 2785
6.7EC.3Minimum conformance requirements  p. 2785
6.7EC.4Test description  p. 2786
6.7EC.4.1Initial conditions  p. 2786
6.7EC.4.2Test procedure  p. 2787
6.7EC.4.3Message contents  p. 2787
6.7EC.5Test requirement  p. 2787
6.7FTransmit intermodulation for category NB1 and NB2  p. 2787
6.7F.4Test description  p. 2788
6.7F.4.1Initial conditions  p. 2788
6.7F.4.2Test procedure  p. 2789
6.7F.4.3Message contents  p. 2789
6.7F.5Test requirement  p. 2789
6.7GTransmit intermodulation for V2X Communication  p. 2790
6.7G.1Transmit intermodulation for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 2790
6.7G.1.1Test purpose  p. 2790
6.7G.1.2Test applicability  p. 2790
6.7G.1.3Minimum conformance requirements  p. 2790
6.7G.1.4Test description  p. 2790
6.7G.1.4.1Initial conditions  p. 2790
6.7G.1.4.2Test procedure  p. 2791
6.7G.1.4.3Message contents  p. 2791
6.7G.1.5Test requirements  p. 2791
6.7G.2Transmit intermodulation for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions  p. 2792
6.7G.2.1Test purpose  p. 2792
6.7G.2.2Test applicability  p. 2792
6.7G.2.3Minimum conformance requirements  p. 2792
6.7G.2.4Test description  p. 2792
6.7G.2.4.1Initial conditions  p. 2792
6.7G.2.4.2Test procedure  p. 2793
6.7G.2.4.3Message contents  p. 2794
6.7G.2.5Test requirements  p. 2794
6.7G.3Transmit intermodulation for V2X Communication / Intra-band contiguous multi-carrier operation  p. 2794
6.7G.3.1Test purpose  p. 2794
6.7G.3.2Test applicability.  p. 2794
6.7G.3.3Minimum conformance requirements  p. 2794
6.7G.3.4Test description  p. 2794
6.7G.3.4.1Initial conditions  p. 2794
6.7G.3.4.2Test procedure  p. 2795
6.7G.3.4.3Message contents  p. 2795
6.7G.3.5Test requirement  p. 2796
6.8Time alignment  p. 2796
6.8.1Void  p. …
6.8AVoid  p. …
6.8BTime alignment error for UL-MIMO  p. 2796
6.8B.1Test purpose  p. 2796
6.8B.2Test applicability  p. 2796
6.8B.3Minimum conformance requirements  p. 2796
6.8B.4Test description  p. 2797
6.8B.4.1Initial condition  p. 2797
6.8B.4.2Test procedure  p. 2797
6.8B.4.3Message contents  p. 2797
6.8B.5Test requirements  p. 2798
7Receiver Characteristics  p. 2799
7.1General  p. 2799
7.2Diversity characteristics  p. 2810
7.3Reference sensitivity level  p. 2810
7.3.1Test purpose  p. 2810
7.3.2Test applicability  p. 2810
7.3.3Minimum conformance requirements  p. 2810
7.3.4Test description  p. 2845
7.3.4.1Initial conditions  p. 2845
7.3.4.2Test procedure  p. 2846
7.3.4.3Message contents  p. 2846
7.3.5Test requirement  p. 2849
7.3_1Reference sensitivity level with 4 Rx antenna ports  p. 2855
7.3_1.1Test purpose  p. 2855
7.3_1.2Test applicability  p. 2855
7.3_1.3Minimum conformance requirements  p. 2855
7.3_1.4Test description  p. 2855
7.3_1.4.1Initial conditions  p. 2855
7.3_1.4.2Test procedure  p. 2856
7.3_1.4.3Message contents  p. 2856
7.3_1.5Test requirement  p. 2857
7.3AReference sensitivity level for CA  p. 2857
7.3A.0Minimum conformance requirements  p. 2857
7.3A.1Reference sensitivity level for CA (intra-band contiguous DL CA and UL CA)  p. 2948
7.3A.1.1Test purpose  p. 2948
7.3A.1.2Test applicability  p. 2949
7.3A.1.3Minimum conformance requirements  p. 2949
7.3A.1.4Test description  p. 2949
7.3A.1.4.1Initial conditions  p. 2949
7.3A.1.4.2Test procedure  p. 2951
7.3A.1.4.3Message contents  p. 2951
7.3A.1.5Test requirement  p. 2952
7.3A.2Reference sensitivity level for CA (intra-band contiguous DL CA without UL CA)  p. 2954
7.3A.2.1Test purpose  p. 2954
7.3A.2.2Test applicability  p. 2954
7.3A.2.3Minimum conformance requirements  p. 2954
7.3A.2.4Test description  p. 2954
7.3A.2.4.1Initial conditions  p. 2954
7.3A.2.4.2Test procedure  p. 2955
7.3A.2.4.3Message contents  p. 2956
7.3A.2.5Test requirement  p. 2956
7.3A.3Reference sensitivity level for CA (inter-band DL CA without UL CA)  p. 2958
7.3A.3.1Test purpose  p. 2958
7.3A.3.2Test applicability  p. 2958
7.3A.3.3Minimum conformance requirements  p. 2958
7.3A.3.4Test description  p. 2958
7.3A.3.4.1Initial conditions  p. 2958
7.3A.3.4.2Test procedure  p. 2975
7.3A.3.4.3Message contents  p. 2975
7.3A.3.5Test requirement  p. 2976
7.3A.4Reference sensitivity level for CA (intra-band non-contiguous DL CA without UL CA)  p. 2989
7.3A.4.1Test purpose  p. 2989
7.3A.4.2Test applicability  p. 2989
7.3A.4.3Minimum conformance requirements  p. 2990
7.3A.4.4Test description  p. 2990
7.3A.4.4.1Initial conditions  p. 2990
7.3A.4.4.2Test procedure  p. 2994
7.3A.4.4.3Message contents  p. 2994
7.3A.4.5Test requirement  p. 2995
7.3A.5Reference sensitivity level for 3DL CA  p. 2998
7.3A.5.1Test purpose  p. 2999
7.3A.5.2Test applicability  p. 2999
7.3A.5.3Minimum conformance requirements  p. 2999
7.3A.5.4Test description  p. 2999
7.3A.5.4.1Initial conditions  p. 2999
7.3A.5.4.2Test procedure  p. 3060
7.3A.5.4.3Message contents  p. 3061
7.3A.5.5Test requirement  p. 3061
7.3A.6Reference sensitivity level for CA (inter-band DL CA and UL CA)  p. 3095
7.3A.6.1Test purpose  p. 3095
7.3A.6.2Test applicability  p. 3095
7.3A.6.3Minimum conformance requirements  p. 3095
7.3A.6.4Test description  p. 3095
7.3A.6.4.1Initial conditions  p. 3095
7.3A.6.4.2Test procedure  p. 3099
7.3A.6.4.3Message contents  p. 3099
7.3A.6.5Test requirement  p. 3099
7.3A.7Reference sensitivity level for CA (intra-band non-contiguous DL CA and UL CA)  p. 3102
7.3A.7.1Test purpose  p. 3102
7.3A.7.2Test applicability  p. 3102
7.3A.7.3Minimum conformance requirements  p. 3102
7.3A.7.4Test description  p. 3102
7.3A.7.4.1Initial conditions  p. 3102
7.3A.7.4.2Test procedure  p. 3103
7.3A.7.4.3Message contents  p. 3103
7.3A.7.5Test requirement  p. 3103
7.3A.8-  p. 3104
7.3A.9Reference sensitivity level for 4DL CA  p. 3105
7.3A.9.1Test purpose  p. 3105
7.3A.9.2Test applicability  p. 3105
7.3A.9.3Minimum conformance requirements  p. 3105
7.3A.9.4Test description  p. 3105
7.3A.9.4.1Initial conditions  p. 3105
7.3A.9.4.2Test procedure  p. 3167
7.3A.9.4.3Message contents  p. 3167
7.3A.9.5Test requirement  p. 3167
7.3A.10Reference sensitivity level for 5DL CA  p. 3188
7.3A.10.1Test purpose  p. 3188
7.3A.10.2Test applicability  p. 3188
7.3A.10.3Minimum conformance requirements  p. 3189
7.3A.10.4Test description  p. 3189
7.3A.10.4.1Initial conditions  p. 3189
7.3A.10.4.2Test procedure  p. 3215
7.3A.10.4.3Message contents  p. 3215
7.3A.10.5Test requirement  p. 3215
7.3A.11Reference sensitivity level for 6DL CA  p. 3226
7.3A.11.1Test purpose  p. 3226
7.3A.11.2Test applicability  p. 3226
7.3A.11.3Minimum conformance requirements  p. 3226
7.3A.11.4Test description  p. 3226
7.3A.11.4.1Initial conditions  p. 3226
7.3A.11.4.2Test procedure  p. 3239
7.3A.11.4.3Message contents  p. 3239
7.3A.11.5Test requirement  p. 3239
7.3BReference sensitivity level for UL-MIMO  p. 3241
7.3B.1Test purpose  p. 3241
7.3B.2Test applicability  p. 3241
7.3B.3Minimum conformance requirements  p. 3241
7.3B.4Test description  p. 3241
7.3B.4.1Initial conditions  p. 3241
7.3B.4.2Test procedure  p. 3242
7.3B.4.3Message contents  p. 3243
7.3B.4.3.1Message contents exceptions (network signalled value "NS_01")  p. 3243
7.3B.4.3.2Message contents exceptions (network signalled value "NS_03")  p. 3243
7.3B.4.3.3Message contents exceptions (network signalled value "NS_06")  p. 3243
7.3B.4.3.4Message contents exceptions (network signalled value "NS_[09]")  p. 3243
7.3B.4.3.5Message contents exceptions (network signalled value "NS_62")  p. 3243
7.3B.5Test requirement  p. 3244
7.3C-  p. 3249
7.3DReference sensitivity level for ProSe  p. 3249
7.3D.0Minimum requirements (QPSK) for ProSe  p. 3249
7.3D.1Reference sensitivity level for ProSe Direct Discovery  p. 3250
7.3D.1.1Test purpose  p. 3250
7.3D.1.2Test applicability  p. 3250
7.3D.1.3Minimum conformance requirements  p. 3250
7.3D.1.4Test description  p. 3251
7.3D.1.4.1Initial conditions  p. 3251
7.3D.1.4.2Test procedure  p. 3251
7.3D.1.4.3Message contents  p. 3252
7.3D.1.5Test requirements  p. 3253
7.3D.2Reference sensitivity level for ProSe Direct Communication  p. 3253
7.3D.2.1Test purpose  p. 3253
7.3D.2.2Test applicability  p. 3253
7.3D.2.3Minimum conformance requirements  p. 3253
7.3D.2.4Test description  p. 3254
7.3D.2.4.1Initial conditions  p. 3254
7.3D.2.4.2Test procedure  p. 3254
7.3D.2.4.3Message contents  p. 3254
7.3D.2.5Test requirements  p. 3254
7.3EReference sensitivity level for UE category 0  p. 3254
7.3EAReference sensitivity level for UE category M1  p. 3257
7.3EA.1Test purpose  p. 3257
7.3EA.2Test applicability  p. 3257
7.3EA.3Minimum conformance requirements  p. 3257
7.3EA.4Test description  p. 3261
7.3EA.4.1Initial conditions  p. 3261
7.3EA.4.2Test procedure  p. 3262
7.3EA.4.3Message contents  p. 3262
7.3EA.4.3.1Message contents exceptions (network signalled value "NS_01")  p. 3262
7.3EA.4.3.2Message contents exceptions (network signalled value "NS_03")  p. 3262
7.3EA.4.3.3Message contents exceptions (network signalled value "NS_06")  p. 3262
7.3EA.4.3.4Message contents exceptions (network signalled value "NS_09")  p. 3263
7.3EA.4.3.5Message contents exceptions (network signalled value "NS_08")  p. 3263
7.3EA.5Test requirement  p. 3263
7.3EBReference sensitivity level for UE category 1bis  p. 3265
7.3EB.1Test purpose  p. 3265
7.3EB.2Test applicability  p. 3265
7.3EB.3Minimum conformance requirements  p. 3266
7.3EB.4Test description  p. 3267
7.3EB.4.1Initial conditions  p. 3267
7.3EB.4.2Test procedure  p. 3268
7.3EB.4.3Message contents  p. 3269
7.3EB.5Test requirement  p. 3269
7.3ECReference sensitivity level for UE category M2  p. 3270
7.3EC.1Test purpose  p. 3270
7.3EC.2Test applicability  p. 3270
7.3EC.3Minimum conformance requirements  p. 3270
7.3EC.4Test description  p. 3274
7.3EC.4.1Initial conditions  p. 3274
7.3EC.4.2Test procedure  p. 3275
7.3EC.4.3Message contents  p. 3275
7.3EC.5Test requirement  p. 3275
7.3FReference sensitivity level for category NB1 and NB2  p. 3277
7.3F.1Reference sensitivity level without repetitions for category NB1 and NB2  p. 3277
7.3F.1.4Test description  p. 3278
7.3F.1.4.1Initial conditions  p. 3278
7.3F.1.4.2Test Procedure  p. 3278
7.3F.1.4.3Message contents  p. 3279
7.3F.1.5Test requirement  p. 3279
7.3F.2Void  p. …
7.3GReference sensitivity level for V2X Communication  p. 3279
7.3G.0Minimum conformance requirements  p. 3279
7.3G.1Reference sensitivity level for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 3281
7.3G.1.1Test purpose  p. 3281
7.3G.1.2Test applicability  p. 3282
7.3G.1.3Minimum conformance requirements  p. 3282
7.3G.1.4Test description  p. 3282
7.3G.1.4.1Initial conditions  p. 3282
7.3G.1.4.2Test procedure  p. 3282
7.3G.1.4.3Message contents  p. 3283
7.3G.1.5Test requirements  p. 3283
7.3G.2Reference sensitivity level for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions  p. 3283
7.3G.2.1Test purpose  p. 3283
7.3G.2.2Test applicability  p. 3283
7.3G.2.3Minimum conformance requirements  p. 3283
7.3G.2.4Test description  p. 3283
7.3G.2.4.1Initial conditions  p. 3283
7.3G.2.4.2Test procedure  p. 3284
7.3G.2.4.3Message contents  p. 3285
7.3G.2.5Test requirements  p. 3285
7.3G.3Reference sensitivity level for V2X Communication / Intra-band contiguous multi-carrier operation  p. 3285
7.3G.3.1Test purpose  p. 3285
7.3G.3.2Test applicability  p. 3285
7.3G.3.3Minimum conformance requirements  p. 3285
7.3G.3.4.1Initial conditions  p. 3286
7.3G.3.4.2Test procedure  p. 3286
7.3G.3.4.3Message contents  p. 3286
7.3G.3.5Test requirements  p. 3287
7.3H-  p. 3287
7.3H.1Reference sensitivity requirements for LTE based 5G terrestrial broadcast  p. 3287
7.3H.1.1Test purpose  p. 3287
7.3H.1.2Test applicability  p. 3287
7.3H.1.3Minimum conformance requirements  p. 3287
7.3H.1.4Test description  p. 3287
7.3H.1.5Test requirement  p. 3288
7.4Maximum input level  p. 3288
7.4.1Test purpose  p. 3288
7.4.2Test applicability  p. 3288
7.4.3Minimum conformance requirements  p. 3288
7.4.4Test description  p. 3288
7.4.4.1Initial conditions  p. 3288
7.4.4.2Test procedure  p. 3290
7.4.4.3Message contents  p. 3290
7.4.5Test requirement  p. 3290
7.4_1Maximum input level with 4 Rx antenna ports  p. 3291
7.4_1.1Test purpose  p. 3291
7.4_1.2Test applicability  p. 3291
7.4_1.3Minimum conformance requirements  p. 3291
7.4_1.4Test description  p. 3291
7.4_1.4.1Initial conditions  p. 3291
7.4_1.4.2Test procedure  p. 3292
7.4_1.4.3Message contents  p. 3292
7.4_1.5Test requirement  p. 3292
7.4_HMaximum input level for 256QAM in DL  p. 3293
7.4_H.1Test purpose  p. 3293
7.4_H.2Test applicability  p. 3293
7.4_H.3Minimum conformance requirements  p. 3293
7.4_H.4Test description  p. 3293
7.4_H.4.1Initial conditions  p. 3293
7.4_H.4.2Test procedure  p. 3294
7.4_H.4.3Message contents  p. 3294
7.4_H.5Test requirement  p. 3294
7.4AMaximum input level for CA  p. 3295
7.4A.1Maximum input level for CA (intra-band contiguous DL CA and UL CA)  p. 3296
7.4A.1.1Test purpose  p. 3296
7.4A.1.2Test applicability  p. 3296
7.4A.1.3Minimum conformance requirements  p. 3297
7.4A.1.4Test description  p. 3297
7.4A.1.4.1Initial conditions  p. 3297
7.4A.1.4.2Test procedure  p. 3299
7.4A.1.4.3Message contents  p. 3299
7.4A.1.5Test requirement  p. 3300
7.4A.1_HMaximum input level for CA (intra-band contiguous DL CA and UL CA) for 256QAM in DL  p. 3301
7.4A.1_H.1Test purpose  p. 3301
7.4A.1_H.2Test applicability  p. 3301
7.4A.1_H.3Minimum conformance requirements  p. 3301
7.4A.1_H.4Test description  p. 3301
7.4A.1_H.4.1Initial conditions  p. 3301
7.4A.1_H.4.2Test procedure  p. 3302
7.4A.1_H.4.3Message contents  p. 3302
7.4A.1_H.5Test requirement  p. 3302
7.4A.2Maximum input level for CA (intra-band contiguous DL CA without UL CA)  p. 3302
7.4A.2.1Test purpose  p. 3302
7.4A.2.2Test applicability  p. 3302
7.4A.2.3Minimum conformance requirements  p. 3302
7.4A.2.4Test description  p. 3302
7.4A.2.4.1Initial conditions  p. 3302
7.4A.2.4.2Test procedure  p. 3306
7.4A.2.4.3Message contents  p. 3306
7.4A.2.5Test requirement  p. 3306
7.4A.2_HMaximum input level for CA (intra-band contiguous DL CA without UL CA) for 256QAM in DL  p. 3307
7.4A.2_H.1Test purpose  p. 3307
7.4A.2_H.2Test applicability  p. 3307
7.4A.2_H.3Minimum conformance requirements  p. 3307
7.4A.2_H.4Test description  p. 3307
7.4A.2_H.4.1Initial conditions  p. 3307
7.4A.2_H.4.2Test procedure  p. 3307
7.4A.2_H.4.3Message contents  p. 3307
7.4A.2_H.5Test requirement  p. 3307
7.4A.3Maximum input level for CA (inter-band DL CA without UL CA)  p. 3308
7.4A.3.4Test description  p. 3308
7.4A.3.4.1Initial conditions  p. 3308
7.4A.3.4.2Test procedure  p. 3310
7.4A.3.4.3Message contents  p. 3310
7.4A.3.5Test requirement  p. 3310
7.4A.3_HMaximum input level for CA (inter-band DL CA without UL CA) for 256QAM in DL  p. 3310
7.4A.3_H.4Test description  p. 3311
7.4A.3_H.4.1Initial conditions  p. 3311
7.4A.3_H.4.2Test procedure  p. 3311
7.4A.3_H.4.3Message contents  p. 3311
7.4A.3_H.5Test requirement  p. 3311
7.4A.4Maximum input level for CA (intra band non-contiguous DL CA without UL CA)  p. 3311
7.4A.4.4Test description  p. 3312
7.4A.4.4.1Initial conditions  p. 3312
7.4A.4.4.2Test procedure  p. 3312
7.4A.4.4.3Message contents  p. 3312
7.4A.4.5Test requirement  p. 3312
7.4A.4_HMaximum input level for CA (intra band non-contiguous DL CA without UL CA) for 256QAM in DL  p. 3313
7.4A.4_H.4Test description  p. 3313
7.4A.4_H.4.1Initial conditions  p. 3313
7.4A.4_H.4.2Test procedure  p. 3313
7.4A.4_H.4.3Message contents  p. 3314
7.4A.4_H.5Test requirement  p. 3314
7.4A.5Maximum input level for 3DL CA  p. 3314
7.4A.5.1Test purpose  p. 3314
7.4A.5.2Test applicability  p. 3314
7.4A.5.3Minimum conformance requirements  p. 3314
7.4A.5.4Test description  p. 3315
7.4A.5.4.1Initial conditions  p. 3315
7.4A.5.4.2Test procedure  p. 3321
7.4A.5.4.3Message contents  p. 3322
7.4A.5.5Test requirement  p. 3322
7.4A.5_HMaximum input level for 3DL CA for 256QAM in DL  p. 3323
7.4A.5_H.1Test purpose  p. 3323
7.4A.5_H.2Test applicability  p. 3323
7.4A.5_H.3Minimum conformance requirements  p. 3323
7.4A.5_H.4Test description  p. 3323
7.4A.5_H.4.1Initial conditions  p. 3323
7.4A.5_H.4.2Test procedure  p. 3324
7.4A.5_H.4.3Message contents  p. 3325
7.4A.5_H.5Test requirement  p. 3325
7.4A.6-  p. 3326
7.4A.7Maximum input level for 4DL CA  p. 3326
7.4A.7.1Test purpose  p. 3326
7.4A.7.2Test applicability  p. 3326
7.4A.7.3Minimum conformance requirements  p. 3326
7.4A.7.4Test description  p. 3326
7.4A.7.4.1Initial conditions  p. 3326
7.4A.7.4.2Test procedure  p. 3337
7.4A.7.4.3Message contents  p. 3339
7.4A.7.5Test requirement  p. 3339
7.4A.7_H Maximum input level for 4DL CA for 256QAM in DL  p. 3339
7.4A.7_H.1Test purpose  p. 3339
7.4A.7_H.2Test applicability  p. 3339
7.4A.7_H.3Minimum conformance requirements  p. 3340
7.4A.7_H.4Test description  p. 3340
7.4A.7_H.4.1Initial conditions  p. 3340
7.4A.7_H.4.2Test procedure  p. 3348
7.4A.7_H.4.3Message contents  p. 3350
7.4A.7_H.5Test requirement  p. 3350
7.4A.8Maximum input level for 5DL CA  p. 3350
7.4A.8.1Test purpose  p. 3350
7.4A.8.2Test applicability  p. 3351
7.4A.8.3Minimum conformance requirements  p. 3351
7.4A.8.4Test description  p. 3351
7.4A.8.4.1Initial conditions  p. 3351
7.4A.8.4.2Test procedure  p. 3360
7.4A.8.4.3Message contents  p. 3362
7.4A.8.5Test requirement  p. 3362
7.4A.8_HMaximum input level for 5DL CA for 256QAM in DL  p. 3363
7.4A.8_H.1Test purpose  p. 3363
7.4A.8_H.2Test applicability  p. 3363
7.4A.8_H.3Minimum conformance requirements  p. 3363
7.4A.8_H.4Test description  p. 3363
7.4A.8_H.4.1Initial conditions  p. 3363
7.4A.8_H.4.2Test procedure  p. 3373
7.4A.8_H.4.3Message contents  p. 3376
7.4A.8_H.5Test requirement  p. 3376
7.4A.9Maximum input level for 6DL CA  p. 3377
7.4A.9.1Test purpose  p. 3377
7.4A.9.2Test applicability  p. 3377
7.4A.9.3Minimum conformance requirements  p. 3377
7.4A.9.4Test description  p. 3378
7.4A.9.4.1Initial conditions  p. 3378
7.4A.9.4.2Test procedure  p. 3387
7.4A.9.4.3Message contents  p. 3389
7.4A.9.5Test requirement  p. 3389
7.4A.9_HMaximum input level for DL CA for 256QAM in DL  p. 3390
7.4A.9_H.1Test purpose  p. 3390
7.4A.9_H.2Test applicability  p. 3390
7.4A.9_H.3Minimum conformance requirements  p. 3390
7.4A.9_H.4Test description  p. 3390
7.4A.9_H.4.1Initial conditions  p. 3390
7.4A.9_H.4.2Test procedure  p. 3401
7.4A.9_H.4.3Message contents  p. 3404
7.4A.9_H.5Test requirement  p. 3404
7.4BMaximum input level for UL-MIMO  p. 3405
7.4B.1Test purpose  p. 3405
7.4B.2Test applicability  p. 3405
7.4B.3Minimum conformance requirements  p. 3405
7.4B.4Test description  p. 3406
7.4B.4.1Initial conditions  p. 3406
7.4B.4.2Test procedure  p. 3406
7.4B.4.3Message contents  p. 3407
7.4B.5Test requirement  p. 3407
7.4C-  p. 3407
7.4DMaximum input level for ProSe  p. 3407
7.4D.0Minimum conformance requirements  p. 3407
7.4D.1Maximum input level for ProSe Direct Discovery  p. 3408
7.4D.1.1Test purpose  p. 3408
7.4D.1.2Test applicability  p. 3408
7.4D.1.3Minimum conformance requirements  p. 3408
7.4D.1.4Test description  p. 3408
7.4D.1.4.1Initial conditions  p. 3408
7.4D.1.4.2Test procedure  p. 3409
7.4D.1.4.3Message contents  p. 3410
7.4D.1.5Test requirement  p. 3410
7.4D.2Maximum input level for ProSe Direct Communication  p. 3411
7.4D.2.1Test purpose  p. 3411
7.4D.2.2Test applicability  p. 3411
7.4D.2.3Minimum conformance requirements  p. 3411
7.4D.2.4Test description  p. 3411
7.4D.2.4.1Initial conditions  p. 3411
7.4D.2.4.2Test procedure  p. 3411
7.4D.2.4.3Message contents  p. 3411
7.4D.2.5Test requirements  p. 3411
7.4EMaximum input level for UE category 0  p. 3411
7.4E.1Test purpose  p. 3411
7.4E.2Test applicability  p. 3411
7.4E.3Minimum conformance requirements  p. 3411
7.4E.4Test description  p. 3411
7.4E.4.1Initial conditions  p. 3411
7.4E.4.2Test procedure  p. 3412
7.4E.4.3Message contents  p. 3412
7.4E.5Test requirement  p. 3412
7.4EAMaximum input level for UE category M1  p. 3413
7.4EA.1Test purpose  p. 3413
7.4EA.2Test applicability  p. 3413
7.4EA.3Minimum conformance requirements  p. 3413
7.4EA.4Test description  p. 3413
7.4EA.4.1Initial conditions  p. 3413
7.4EA.4.2Test procedure  p. 3414
7.4EA.4.3Message contents  p. 3414
7.4EA.5Test requirement  p. 3414
7.4EBMaximum input level for UE Category 1bis  p. 3415
7.4EB.1Test purpose  p. 3415
7.4EB.2Test applicability  p. 3415
7.4EB.3Minimum conformance requirements  p. 3415
7.4EB.4Test description  p. 3415
7.4EB.4.1Initial conditions  p. 3415
7.4EB.4.2Test procedure  p. 3415
7.4EB.4.3Message contents  p. 3415
7.4EB.5Test requirement  p. 3415
7.4ECMaximum input level for UE category M2  p. 3416
7.4EC.1Test purpose  p. 3416
7.4EC.2Test applicability  p. 3416
7.4EC.3Minimum conformance requirements  p. 3416
7.4EC.4Test description  p. 3416
7.4EC.4.1Initial conditions  p. 3416
7.4EC.4.2Test procedure  p. 3416
7.4EC.4.3Message contents  p. 3416
7.4EC.5Test requirement  p. 3416
7.4FMaximum input level for category NB1 and NB2  p. 3417
7.4GMaximum input level for V2X Communication  p. 3418
7.4G.1Maximum input level for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 3418
7.4G.1.1Test purpose  p. 3418
7.4G.1.2Test applicability  p. 3418
7.4G.1.3Minimum conformance requirements  p. 3418
7.4G.1.4Test description  p. 3419
7.4G.1.4.1Initial conditions  p. 3419
7.4G.1.4.2Test procedure  p. 3419
7.4G.1.4.3Message contents  p. 3419
7.4G.1.5Test requirements  p. 3420
7.4G.2Maximum input level for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions  p. 3420
7.4G.2.1Test purpose  p. 3420
7.4G.2.2Test applicability  p. 3420
7.4G.2.3Minimum conformance requirements  p. 3420
7.4G.2.4Test description  p. 3420
7.4G.2.4.1Initial conditions  p. 3420
7.4G.2.4.2Test procedure  p. 3421
7.4G.2.4.3Message contents  p. 3422
7.4G.2.5Test requirements  p. 3422
7.4G.3Maximum input level for V2X Communication / Intra-band contiguous multi-carrier operation  p. 3422
7.4G.3.1Test purpose  p. 3422
7.4G.3.2Test applicability  p. 3422
7.4G.3.3Minimum conformance requirements  p. 3422
7.4G.3.4Test description  p. 3423
7.4G.3.4.1Initial conditions  p. 3423
7.4G.3.4.2Test procedure  p. 3423
7.4G.3.4.3Message contents  p. 3424
7.4G.3.5Test requirements  p. 3424
7.4H-  p. 3424
7.4H.1Minimum input level for LTE based 5G terrestrial broadcast  p. 3424
7.4H.1.1Test purpose  p. 3424
7.4H.1.2Test applicability  p. 3424
7.4H.1.3Minimum conformance requirements  p. 3424
7.4H.1.4Test description  p. 3424
7.4H.1.5Test requirement  p. 3425
7.5Adjacent Channel Selectivity (ACS)  p. 3426
7.5.1Test purpose  p. 3426
7.5.2Test applicability  p. 3426
7.5.3Minimum conformance requirements  p. 3426
7.5.4Test description  p. 3427
7.5.4.1Initial conditions  p. 3427
7.5.4.2Test procedure  p. 3428
7.5.4.3Message contents  p. 3429
7.5.5Test requirement  p. 3429
7.5_1Adjacent Channel Selectivity (ACS) with 4 Rx antenna ports  p. 3430
7.5_1.1Test purpose  p. 3430
7.5_1.2Test applicability  p. 3430
7.5_1.3Minimum conformance requirements  p. 3430
7.5_1.4Test description  p. 3430
7.5.4_1.1Initial conditions  p. 3430
7.5_1.4.2Test procedure  p. 3431
7.5_1.4.3Message contents  p. 3431
7.5_1.5Test requirement  p. 3431
7.5AAdjacent Channel Selectivity (ACS) for CA  p. 3432
7.5A.1Adjacent Channel Selectivity (ACS) for CA (intra-band contiguous DL CA and UL CA)  p. 3436
7.5A.1.1Test purpose  p. 3436
7.5A.1.2Test applicability  p. 3436
7.5A.1.3Minimum conformance requirements  p. 3436
7.5A.1.4Test description  p. 3436
7.5A.1.4.1Initial conditions  p. 3436
7.5A.1.4.2Test procedure  p. 3438
7.5A.1.4.3Message contents  p. 3439
7.5A.1.5Test Requirements  p. 3440
7.5A.2Adjacent Channel Selectivity (ACS) for CA (intra-band contiguous DL CA without UL CA)  p. 3441
7.5A.2.4Test description  p. 3441
7.5A.2.4.1Initial conditions  p. 3441
7.5A.2.4.2Test procedure  p. 3442
7.5A.2.4.3Message contents  p. 3443
7.5A.2.5Test Requirements  p. 3443
7.5A.3Adjacent Channel Selectivity (ACS) for CA (inter-band DL CA without UL CA)  p. 3444
7.5A.3.4Test description  p. 3445
7.5A.3.4.1Initial conditions  p. 3445
7.5A.3.4.2Test procedure  p. 3446
7.5A.3.4.3Message contents  p. 3447
7.5A.3.5Test Requirements  p. 3447
7.5A.4Adjacent Channel Selectivity (ACS) for CA (intra-band non-contiguous DL CA without UL CA)  p. 3449
7.5A.4.4Test description  p. 3449
7.5A.4.4.1Initial conditions  p. 3449
7.5A.4.4.2Test procedure  p. 3450
7.5A.4.4.3Message contents  p. 3450
7.5A.4.5Test requirement  p. 3451
7.5A.5Adjacent Channel Selectivity (ACS) for 3DL CA  p. 3451
7.5A.5.1Test purpose  p. 3451
7.5A.5.2Test applicability  p. 3452
7.5A.5.3Minimum conformance requirements  p. 3452
7.5A.5.4Test description  p. 3452
7.5A.5.4.1Initial conditions  p. 3452
7.5A.5.4.2Test procedure  p. 3457
7.5A.5.4.3Message contents  p. 3459
7.5A.5.5Test requirement  p. 3459
7.5A.6-  p. 3463
7.5A.7Adjacent Channel Selectivity (ACS) for 4DL CA  p. 3463
7.5A.7.1Test purpose  p. 3463
7.5A.7.2Test applicability  p. 3463
7.5A.7.3Minimum conformance requirements  p. 3464
7.5A.7.4Test description  p. 3464
7.5A.7.4.1Initial conditions  p. 3464
7.5A.7.4.2Test procedure  p. 3473
7.5A.7.4.3Message contents  p. 3475
7.5A.7.5Test requirement  p. 3475
7.5A.8Adjacent Channel Selectivity (ACS) for 5DL CA  p. 3479
7.5A.8.1Test purpose  p. 3479
7.5A.8.2Test applicability  p. 3479
7.5A.8.3Minimum conformance requirements  p. 3479
7.5A.8.4Test description  p. 3479
7.5A.8.4.1Initial conditions  p. 3479
7.5A.8.4.2Test procedure  p. 3488
7.5A.8.4.3Message contents  p. 3493
7.5A.8.5Test requirement  p. 3494
7.5A.9Adjacent Channel Selectivity (ACS) for 6DL CA  p. 3497
7.5A.9.1Test purpose  p. 3497
7.5A.9.2Test applicability  p. 3498
7.5A.9.3Minimum conformance requirements  p. 3498
7.5A.9.4Test description  p. 3498
7.5A.9.4.1Initial conditions  p. 3498
7.5A.9.4.2Test procedure  p. 3513
7.5A.9.4.3Message contents  p. 3519
7.5A.9.5Test requirement  p. 3519
7.5BAdjacent Channel Selectivity (ACS) for UL-MIMO  p. 3522
7.5B.1Test purpose  p. 3522
7.5B.2Test applicability  p. 3523
7.5B.3Minimum conformance requirements  p. 3523
7.5B.4Test description  p. 3523
7.5B.4.1Initial conditions  p. 3523
7.5B.4.2Test procedure  p. 3524
7.5B.4.3Message contents  p. 3524
7.5B.5Test requirement  p. 3525
7.5DAdjacent Channel Selectivity (ACS) for ProSe  p. 3526
7.5D.0Minimum conformance requirements  p. 3526
7.5D.1Adjacent Channel Selectivity (ACS) for ProSe Direct Discovery  p. 3527
7.5D.1.1Test Purpose  p. 3527
7.5D.1.2Test Applicability  p. 3527
7.5D.1.3Minimum Conformance Requirements  p. 3527
7.5D.1.4Test Description  p. 3527
7.5D.1.4.1Initial Conditions  p. 3527
7.5D.1.4.2Test Procedure  p. 3528
7.5D.1.4.3Message Contents  p. 3529
7.5D.1.5Test Requirement  p. 3530
7.5D.2Adjacent Channel Selectivity (ACS) for ProSe Direct Communication  p. 3531
7.5D.2.1Test Purpose  p. 3531
7.5D.2.2Test Applicability  p. 3531
7.5D.2.3Minimum Conformance Requirements  p. 3531
7.5D.2.4Test Description  p. 3531
7.5D.2.4.1Initial Conditions  p. 3531
7.5D.2.4.2Test Procedure  p. 3531
7.5D.2.4.3Message Contents  p. 3531
7.5D.2.5Test Requirement  p. 3531
7.5EAdjacent Channel Selectivity (ACS) for category 0  p. 3531
7.5E.1Test purpose  p. 3531
7.5E.2Test applicability  p. 3532
7.5E.3Minimum conformance requirements  p. 3532
7.5E.4Test description  p. 3532
7.5E.4.1Initial conditions  p. 3532
7.5E.4.2Test procedure  p. 3532
7.5E.4.3Message contents  p. 3532
7.5E.5Test requirement  p. 3533
7.5EAAdjacent Channel Selectivity (ACS) for UE category M1  p. 3533
7.5EA.1Test purpose  p. 3533
7.5EA.2Test applicability  p. 3534
7.5EA.3Minimum conformance requirements  p. 3534
7.5EA.4Test description  p. 3535
7.5EA.4.1Initial conditions  p. 3535
7.5EA.4.2Test procedure  p. 3536
7.5EA.4.3Message contents  p. 3536
7.5EA.5Test requirement  p. 3537
7.5EBAdjacent Channel Selectivity (ACS) for UE Category 1bis  p. 3538
7.5EB.1Test purpose  p. 3538
7.5EB.2Test applicability  p. 3538
7.5EB.3Minimum conformance requirements  p. 3538
7.5EB.4Test description  p. 3538
7.5EB.4.1Initial conditions  p. 3538
7.5EB.4.2Test procedure  p. 3538
7.5EB.4.3Message contents  p. 3538
7.5EB.5Test requirement  p. 3538
7.5ECAdjacent Channel Selectivity (ACS) for UE category M2  p. 3539
7.5EC.1Test purpose  p. 3539
7.5EC.2Test applicability  p. 3539
7.5EC.3Minimum conformance requirements  p. 3539
7.5EC.4Test description  p. 3541
7.5EC.4.1Initial conditions  p. 3541
7.5EC.4.2Test procedure  p. 3541
7.5EC.4.3Message contents  p. 3541
7.5EC.5Test requirement  p. 3542
7.5FAdjacent Channel Selectivity (ACS) for category NB1 and NB2  p. 3542
7.5GAdjacent Channel Selectivity (ACS) for V2X Communication  p. 3545
7.5G.1Adjacent channel selectivity (ACS) for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 3545
7.5G.1.1Test Purpose  p. 3545
7.5G.1.2Test Applicability  p. 3545
7.5G.1.3Minimum Conformance Requirements  p. 3545
7.5G.1.4Test Description  p. 3546
7.5G.1.4.1Initial Conditions  p. 3546
7.5G.1.4.2Test Procedure  p. 3547
7.5G.1.4.3Message Contents  p. 3547
7.5G.1.5Test Requirement  p. 3547
7.5G.2Adjacent channel selectivity (ACS) for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions  p. 3548
7.5G.2.1Test Purpose  p. 3548
7.5G.2.2Test Applicability  p. 3548
7.5G.2.3Minimum Conformance Requirements  p. 3548
7.5G.2.4Test Description  p. 3549
7.5G.2.4.1Initial Conditions  p. 3549
7.5G.2.4.2Test Procedure  p. 3550
7.5G.2.4.3Message Contents  p. 3551
7.5G.2.5Test Requirement  p. 3551
7.5G.3Adjacent channel selectivity (ACS) for V2X Communication / Intra-band contiguous multi-carrier operation  p. 3552
7.5G.3.1Test Purpose  p. 3552
7.5G.3.2Test Applicability  p. 3552
7.5G.3.3Minimum Conformance Requirements  p. 3552
7.5G.3.4Test Description  p. 3553
7.5G.3.4.1Initial Conditions  p. 3553
7.5G.3.4.2Test Procedure  p. 3554
7.5G.3.4.3Message Contents  p. 3554
7.5G.3.5Test Requirement  p. 3554
7.5H-  p. 3555
7.5H.1Adjacent channel selectivity for LTE based 5G terrestrial broadcast  p. 3555
7.5H.1.1Test purpose  p. 3555
7.5H.1.2Test applicability  p. 3556
7.5H.1.3Minimum conformance requirements  p. 3556
7.5H.1.4Test description  p. 3556
7.5H.1.5Test requirement  p. 3557
7.6Blocking characteristics  p. 3557
7.6.1In-band blocking  p. 3557
7.6.1.1Test Purpose  p. 3557
7.6.1.2Test Applicability  p. 3557
7.6.1.3Minimum Conformance Requirements  p. 3557
7.6.1.4Test Description  p. 3558
7.6.1.4.1Initial Conditions  p. 3558
7.6.1.4.2Test Procedure  p. 3559
7.6.1.4.3Message Contents  p. 3560
7.6.1.5Test Requirement  p. 3561
7.6.1_1In-band blocking with 4 Rx antenna ports  p. 3562
7.6.1_1.1Test Purpose  p. 3562
7.6.1_1.2Test Applicability  p. 3562
7.6.1_1.3Minimum Conformance Requirements  p. 3562
7.6.1_1.4Test Description  p. 3562
7.6.1_1.4.1Initial Conditions  p. 3562
7.6.1_1.4.2Test Procedure  p. 3563
7.6.1_1.4.3Message Contents  p. 3563
7.6.1_1.5Test Requirement  p. 3563
7.6.1AIn-band blocking for CA  p. 3564
7.6.1A.0Minimum conformance requirements  p. 3564
7.6.1A.1In-band blocking for CA (intra-band contiguous DL CA and UL CA)  p. 3567
7.6.1A.1.1Test Purpose  p. 3567
7.6.1A.1.2Test Applicability  p. 3567
7.6.1A.1.3Minimum Conformance Requirements  p. 3567
7.6.1A.1.4Test Description  p. 3567
7.6.1A.1.5Test Requirement  p. 3571
7.6.1A.2In-band blocking for CA (intra-band contiguous DL CA without UL CA)  p. 3572
7.6.1A.2.4Test Description  p. 3572
7.6.1A.2.4.1Initial Conditions  p. 3572
7.6.1A.2.4.2Test Procedure  p. 3573
7.6.1A.2.4.3Message Contents  p. 3574
7.6.1A.2.5Test Requirement  p. 3574
7.6.1A.3In-band blocking for CA (inter-band DL CA without UL CA)  p. 3575
7.6.1A.3.4Test Description  p. 3575
7.6.1A.3.4.1Initial Conditions  p. 3575
7.6.1A.3.4.2Test Procedure  p. 3577
7.6.1A.3.4.3Message Contents  p. 3577
7.6.1A.3.5Test Requirement  p. 3577
7.6.1A.4In-band blocking for CA (intra-band non-contiguous DL CA without UL CA)  p. 3579
7.6.1A.4.4Test description  p. 3580
7.6.1A.4.4.1Initial Conditions  p. 3580
7.6.1A.4.4.2Test Procedure  p. 3580
7.6.1A.4.4.3Message Contents  p. 3581
7.6.1A.4.5Test Requirement  p. 3581
7.6.1A.5In-band blocking for 3DL CA  p. 3582
7.6.1A.5.1Test Purpose  p. 3582
7.6.1A.5.2Test Applicability  p. 3582
7.6.1A.5.4Test Description  p. 3582
7.6.1A.5.4.1Initial Conditions  p. 3582
7.6.1A.5.4.2Test Procedure  p. 3587
7.6.1A.5.4.3Message Contents  p. 3589
7.6.1A.5.5Test Requirement  p. 3590
7.6.1A.6-  p. 3593
7.6.1A.7In-band blocking for 4DL CA  p. 3593
7.6.1A.7.1Test Purpose  p. 3593
7.6.1A.7.2Test Applicability  p. 3594
7.6.1A.7.3Minimum Conformance Requirements  p. 3594
7.6.1A.7.4Test Description  p. 3594
7.6.1A.7.4.1Initial Conditions  p. 3594
7.6.1A.7.4.2Test Procedure  p. 3604
7.6.1A.7.4.3Message Contents  p. 3607
7.6.1A.7.5Test Requirement  p. 3607
7.6.1A.8In-band blocking for 5DL CA  p. 3610
7.6.1A.8.1Test Purpose  p. 3610
7.6.1A.8.2Test Applicability  p. 3610
7.6.1A.8.3Minimum Conformance Requirements  p. 3610
7.6.1A.8.4Test Description  p. 3610
7.6.1A.8.4.1Initial Conditions  p. 3610
7.6.1A.8.4.2Test Procedure  p. 3620
7.6.1A.8.4.3Message Contents  p. 3623
7.6.1A.8.5Test Requirement  p. 3623
7.6.1A.9In-band blocking for 6DL CA  p. 3627
7.6.1A.9.1Test Purpose  p. 3627
7.6.1A.9.2Test Applicability  p. 3627
7.6.1A.9.3Minimum Conformance Requirements  p. 3627
7.6.1A.9.4Test Description  p. 3627
7.6.1A.9.4.1Initial Conditions  p. 3627
7.6.1A.9.4.2Test Procedure  p. 3640
7.6.1A.9.4.3Message Contents  p. 3644
7.6.1A.9.5Test Requirement  p. 3644
7.6.1A.10In-band blocking for 7DL CA  p. 3648
7.6.1A.10.1Test Purpose  p. 3648
7.6.1A.10.2Test Applicability  p. 3648
7.6.1A.10.3Minimum Conformance Requirements  p. 3648
7.6.1A.10.4Test Description  p. 3648
7.6.1A.10.4.1Initial Conditions  p. 3648
7.6.1A.10.4.2Test Procedure  p. 3652
7.6.1BIn-band blocking for UL-MIMO  p. 3658
7.6.1B.1Test Purpose  p. 3658
7.6.1B.2Test Applicability  p. 3659
7.6.1B.3Minimum Conformance Requirements  p. 3659
7.6.1B.4Test Description  p. 3659
7.6.1B.4.1Initial Conditions  p. 3659
7.6.1B.4.2Test Procedure  p. 3660
7.6.1B.4.3Message Contents  p. 3661
7.6.1B.5Test Requirement  p. 3661
7.6.1DIn-band blocking for ProSe  p. 3662
7.6.1D.0Minimum conformance requirements  p. 3662
7.6.1D.1In-band blocking for ProSe Direct Discovery  p. 3663
7.6.1D.1.1Test Purpose  p. 3664
7.6.1D.1.2Test Applicability  p. 3664
7.6.1D.1.3Minimum Conformance Requirements  p. 3664
7.6.1D.1.4Test Description  p. 3664
7.6.1D.1.5Test Requirement  p. 3666
7.6.1D.2In-band blocking for ProSe Direct Communication  p. 3667
7.6.1D.2.1Test Purpose  p. 3667
7.6.1D.2.2Test Applicability  p. 3667
7.6.1D.2.3Minimum Conformance Requirements  p. 3667
7.6.1D.2.4Test Description  p. 3667
7.6.1D.2.5Test Requirement  p. 3667
7.6.1EIn-band blocking for UE category 0  p. 3668
7.6.1E.1Test Purpose  p. 3668
7.6.1E.2Test Applicability  p. 3668
7.6.1E.3Minimum Conformance Requirements  p. 3668
7.6.1E.4Test Description  p. 3668
7.6.1E.4.1Initial Conditions  p. 3668
7.6.1E.4.2Test Procedure  p. 3669
7.6.1E.4.3Message Contents  p. 3669
7.6.1E.5Test Requirement  p. 3669
7.6.1EAIn-band blocking for UE category M1  p. 3670
7.6.1EA.1Test Purpose  p. 3670
7.6.1EA.2Test Applicability  p. 3670
7.6.1EA.3Minimum Conformance Requirements  p. 3670
7.6.1EA.4Test Description  p. 3671
7.6.1EA.4.1Initial Conditions  p. 3671
7.6.1EA.4.2Test Procedure  p. 3672
7.6.1EA.4.3Message Contents  p. 3672
7.6.1EA.5Test Requirement  p. 3673
7.6.1EBIn-band blocking for UE Category 1bis  p. 3673
7.6.1EB.1Test Purpose  p. 3673
7.6.1EB.2Test Applicability  p. 3673
7.6.1EB.3Minimum Conformance Requirements  p. 3673
7.6.1EB.4Test Description  p. 3674
7.6.1EB.4.2Test Procedure  p. 3674
7.6.1EB.4.3Message Contents  p. 3674
7.6.1EB.5Test Requirement  p. 3674
7.6.1ECIn-band blocking for UE category M2  p. 3675
7.6.1EC.1Test purpose  p. 3675
7.6.1EC.2Test applicability  p. 3675
7.6.1EC.3Minimum conformance requirements  p. 3675
7.6.1EC.4Test description  p. 3676
7.6.1EC.4.1Initial conditions  p. 3676
7.6.1EC.4.2Test procedure  p. 3676
7.6.1EC.4.3Message contents  p. 3676
7.6.1EC.5Test requirement  p. 3676
7.6.1FIn-band blocking for category NB1 and NB2  p. 3677
7.6.1GIn-band blocking for V2X Communication  p. 3679
7.6.1G.1In-band blocking for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 3679
7.6.1G.1.1Test Purpose  p. 3679
7.6.1G.1.2Test Applicability  p. 3679
7.6.1G.1.3Minimum Conformance Requirements  p. 3679
7.6.1G.1.4Test Description  p. 3680
7.6.1G.1.5Test Requirement  p. 3681
7.6.1G.2In-band blocking for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions  p. 3682
7.6.1G.2.1Test Purpose  p. 3682
7.6.1G.2.2Test Applicability  p. 3682
7.6.1G.2.3Minimum Conformance Requirements  p. 3682
7.6.1G.2.4Test Description  p. 3683
7.6.1G.2.4.1Initial conditions  p. 3683
7.6.1G.2.4.2Test procedure  p. 3684
7.6.1G.2.4.3Message contents  p. 3685
7.6.1G.2.5Test Requirement  p. 3685
7.6.1G.3In-band blocking for V2X Communication / Intra-band contiguous multi-carrier operation  p. 3685
7.6.1G.3.1Test Purpose  p. 3685
7.6.1G.3.2Test Applicability  p. 3685
7.6.1G.3.3Minimum Conformance Requirements  p. 3686
7.6.1G.3.4Test Description  p. 3686
7.6.1G.3.4.1Initial conditions  p. 3686
7.6.1G.3.4.2Test procedure  p. 3687
7.6.1G.3.4.3Message contents  p. 3687
7.6.1G.3.5Test Requirement  p. 3687
7.6.2Out-of-band blocking  p. 3688
7.6.2.1Test Purpose  p. 3688
7.6.2.2Test Applicability  p. 3688
7.6.2.3Minimum Conformance Requirements  p. 3688
7.6.2.4Test Description  p. 3689
7.6.2.4.1Initial Conditions  p. 3689
7.6.2.4.2Test Procedure  p. 3691
7.6.2.4.3Message Contents  p. 3691
7.6.2.5Test Requirement  p. 3691
7.6.2_1Out-of-band blocking with 4 Rx antenna ports  p. 3692
7.6.2_1.1Test Purpose  p. 3692
7.6.2_1.2Test Applicability  p. 3692
7.6.2_1.3Minimum Conformance Requirements  p. 3693
7.6.2_1.4Test Description  p. 3693
7.6.2_1.4.1Initial Conditions  p. 3693
7.6.2_1.4.2Test Procedure  p. 3693
7.6.2_1.4.3Message Contents  p. 3693
7.6.2_1.5Test Requirement  p. 3693
7.6.2AOut-of-band blocking for CA  p. 3694
7.6.2A.0Minimum conformance requirements  p. 3694
7.6.2A.1Out-of-band blocking for CA (intra-band contiguous DL CA and UL CA)  p. 3697
7.6.2A.1.1Test Purpose  p. 3697
7.6.2A.1.2Test Applicability  p. 3697
7.6.2A.1.3Minimum Conformance Requirements  p. 3697
7.6.2A.1.4Test Description  p. 3698
7.6.2A.1.5Test Requirement  p. 3700
7.6.2A.2Out-of-band blocking for CA (intra-band contiguous DL CA without UL CA)  p. 3701
7.6.2A.2.4Test Description  p. 3701
7.6.2A.2.4.1Initial Conditions  p. 3701
7.6.2A.2.4.2Test Procedure  p. 3702
7.6.2A.2.4.3Message Contents  p. 3703
7.6.2A.2.5Test Requirement  p. 3703
7.6.2A.3Out-of-band blocking for CA (inter-band DL CA without UL CA)  p. 3703
7.6.2A.3.4Test Description  p. 3704
7.6.2A.3.4.1Initial Conditions  p. 3704
7.6.2A.3.4.2Test Procedure  p. 3707
7.6.2A.3.4.3Message Contents  p. 3707
7.6.2A.3.5Test Requirement  p. 3707
7.6.2A.4Out-of-band blocking for CA (intra-band non-contiguous DL CA without UL CA)  p. 3709
7.6.2A.4.4Test description  p. 3709
7.6.2A.4.4.1Initial Conditions  p. 3709
7.6.2A.4.4.2Test Procedure  p. 3710
7.6.2A.4.4.3Message Contents  p. 3710
7.6.2A.4.5Test Requirement  p. 3710
7.6.2A.5Out-of-band blocking for 3DL CA  p. 3711
7.6.2A.5.1Test Purpose  p. 3711
7.6.2A.5.2Test Applicability  p. 3711
7.6.2A.5.3Minimum Conformance Requirements  p. 3711
7.6.2A.5.4Test Description  p. 3712
7.6.2A.5.4.1Initial Conditions  p. 3712
7.6.2A.5.4.2Test Procedure  p. 3717
7.6.2A.5.4.3Message Contents  p. 3718
7.6.2A.5.5Test Requirement  p. 3719
7.6.2A.6-  p. 3721
7.6.2A.7Out-of-band blocking for 4DL CA  p. 3721
7.6.2A.7.1Test Purpose  p. 3721
7.6.2A.7.2Test Applicability  p. 3721
7.6.2A.7.3Minimum Conformance Requirements  p. 3721
7.6.2A.7.4Test Description  p. 3721
7.6.2A.7.4.1Initial Conditions  p. 3721
7.6.2A.7.4.2Test Procedure  p. 3730
7.6.2A.7.4.3Message Contents  p. 3731
7.6.2A.7.5Test Requirement  p. 3731
7.6.2A.8Out-of-band blocking for 5DL CA  p. 3734
7.6.2A.8.1Test Purpose  p. 3734
7.6.2A.8.2Test Applicability  p. 3734
7.6.2A.8.3Minimum Conformance Requirements  p. 3734
7.6.2A.8.4Test Description  p. 3734
7.6.2A.8.4.1Initial Conditions  p. 3734
7.6.2A.8.4.2Test Procedure  p. 3742
7.6.2A.8.4.3Message Contents  p. 3745
7.6.2A.8.5Test Requirement  p. 3745
7.6.2A.9Out-of-band blocking for 6DL CA  p. 3747
7.6.2A.9.1Test Purpose  p. 3747
7.6.2A.9.2Test Applicability  p. 3747
7.6.2A.9.3Minimum Conformance Requirements  p. 3747
7.6.2A.9.4Test Description  p. 3747
7.6.2A.9.4.1Initial Conditions  p. 3747
7.6.2A.9.4.2Test Procedure  p. 3766
7.6.2A.9.4.3Message Contents  p. 3770
7.6.2A.9.5Test Requirement  p. 3770
7.6.2A.10Out-of-band blocking for 7DL CA  p. 3773
7.6.2A.10.1Test Purpose  p. 3773
7.6.2A.10.2Test Applicability  p. 3773
7.6.2A.10.3Minimum Conformance Requirements  p. 3773
7.6.2A.10.4Test Description  p. 3773
7.6.2A.10.4.1Initial Conditions  p. 3773
7.6.2A.10.4.2Test Procedure  p. 3777
7.6.2A.10.4.3Message Contents  p. 3778
7.6.2A.10.5Test Requirement  p. 3779
7.6.2BOut-of-band blocking for UL-MIMO  p. 3781
7.6.2B.1Test Purpose  p. 3781
7.6.2B.2Test Applicability  p. 3781
7.6.2B.3Minimum Conformance Requirements  p. 3781
7.6.2B.4Test Description  p. 3781
7.6.2B.4.1Initial Conditions  p. 3781
7.6.2B.4.2Test Procedure  p. 3782
7.6.2B.4.3Message Contents  p. 3783
7.6.2B.5Test Requirement  p. 3783
7.6.2DOut-of-band blocking for ProSe  p. 3784
7.6.2D.0Minimum conformance requirements  p. 3784
7.6.2D.1Out-of-band blocking for ProSe Direct Discovery  p. 3785
7.6.2D.1.1Test Purpose  p. 3785
7.6.2D.1.2Test Applicability  p. 3785
7.6.2D.1.3Minimum Conformance Requirements  p. 3785
7.6.2D.1.4Test Description  p. 3785
7.6.2D.1.5Test Requirement  p. 3788
7.6.2D.2Out-of-band blocking for Prose Direct Communication  p. 3788
7.6.2D.2.1Test Purpose  p. 3788
7.6.2D.2.2Test Applicability  p. 3788
7.6.2D.2.3Minimum Conformance Requirements  p. 3788
7.6.2D.2.4Test Description  p. 3788
7.6.2D.2.5Test Requirement  p. 3788
7.6.2EOut-of-band blocking for UE category 0  p. 3789
7.6.2E.1Test Purpose  p. 3789
7.6.2E.2Test Applicability  p. 3789
7.6.2E.3Minimum Conformance Requirements  p. 3789
7.6.2E.4Test Description  p. 3789
7.6.2E.4.1Initial Conditions  p. 3789
7.6.2E.4.2Test Procedure  p. 3790
7.6.2E.4.3Message Contents  p. 3790
7.6.2E.5Test Requirement  p. 3790
7.6.2EAOut-of-band blocking for UE category M1  p. 3791
7.6.2EA.1Test Purpose  p. 3791
7.6.2EA.2Test Applicability  p. 3791
7.6.2EA.3Minimum Conformance Requirements  p. 3791
7.6.2EA.4Test Description  p. 3791
7.6.2EA.4.1Initial Conditions  p. 3791
7.6.2EA.4.2Test Procedure  p. 3792
7.6.2EA.4.3Message Contents  p. 3792
7.6.2EA.5Test Requirement  p. 3793
7.6.2EBOut-of-band blocking for UE category 1bis  p. 3794
7.6.2EB.1Test Purpose  p. 3794
7.6.2EB.2Test Applicability  p. 3794
7.6.2EB.3Minimum Conformance Requirements  p. 3794
7.6.2EB.4Test Description  p. 3794
7.6.2EB.4.1Initial Conditions  p. 3794
7.6.2EB.4.2Test Procedure  p. 3794
7.6.2EB.4.3Message Contents  p. 3794
7.6.2EB.5Test Requirement  p. 3794
7.6.2ECOut-of-band blocking for UE category M2  p. 3795
7.6.2EC.1Test Purpose  p. 3795
7.6.2EC.2Test Applicability  p. 3795
7.6.2EC.3Minimum Conformance Requirements  p. 3795
7.6.2EC.4Test Description  p. 3795
7.6.2EC.4.1Initial Conditions  p. 3795
7.6.2EC.4.2Test Procedure  p. 3796
7.6.2EC.4.3Message Contents  p. 3796
7.6.2EC.5Test Requirement  p. 3796
7.6.2GOut-of-band blocking for V2X Communication  p. 3797
7.6.2G.1Out-of-band blocking for V2X Communication/ Non-concurrent with E-UTRA uplink transmissions  p. 3797
7.6.2G.1.1Test Purpose  p. 3797
7.6.2G.1.2Test Applicability  p. 3797
7.6.2G.1.3Minimum Conformance Requirements  p. 3797
7.6.2G.1.4Test Description  p. 3798
7.6.2G.1.5Test Requirement  p. 3799
7.6.2G.2Out-of-band blocking for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions  p. 3799
7.6.2G.2.1Test Purpose  p. 3799
7.6.2G.2.2Test Applicability  p. 3799
7.6.2G.2.3Minimum Conformance Requirements  p. 3799
7.6.2G.2.4Test Description  p. 3800
7.6.2G.2.4.1Initial conditions  p. 3800
7.6.2G.2.4.2Test procedure  p. 3801
7.6.2G.2.4.3Message contents  p. 3802
7.6.2G.2.5Test Requirement  p. 3802
7.6.2G.3Out-of-band blocking for V2X Communication / Intra-band contiguous multi-carrier operation  p. 3802
7.6.2G.3.1Test Purpose  p. 3802
7.6.2G.3.2Test Applicability  p. 3802
7.6.2G.3.3Minimum Conformance Requirements  p. 3802
7.6.2G.3.4Test Description  p. 3803
7.6.2G.3.4.1Initial conditions  p. 3803
7.6.2G.3.4.2Test procedure  p. 3804
7.6.2G.3.4.3Message contents  p. 3804
7.6.2G.3.5Test Requirement  p. 3804
7.6.2FOut-of-band blocking for category NB1 and NB2  p. 3804
7.6.3Narrow band blocking  p. 3807
7.6.3.1Test Purpose  p. 3807
7.6.3.2Test Applicability  p. 3807
7.6.3.3Minimum Conformance Requirements  p. 3807
7.6.3.4Test Description  p. 3808
7.6.3.4.1Initial Conditions  p. 3808
7.6.3.4.2Test Procedure  p. 3809
7.6.3.4.3Message Contents  p. 3809
7.6.3.5Test Requirement  p. 3809
7.6.3_1Narrow band blocking with 4 Rx antenna ports  p. 3810
7.6.3_1.1Test Purpose  p. 3810
7.6.3_1.2Test Applicability  p. 3810
7.6.3_1.3Minimum Conformance Requirements  p. 3810
7.6.3_1.4Test Description  p. 3810
7.6.3_1.4.1Initial Conditions  p. 3810
7.6.3_1.4.2Test Procedure  p. 3811
7.6.3_1.4.3Message Contents  p. 3811
7.6.3_1.5Test Requirement  p. 3811
7.6.3ANarrow band blocking for CA  p. 3812
7.6.3A.0Minimum conformance requirements  p. 3812
7.6.3A.1Narrow band blocking for CA (intra-band contiguous DL CA and UL CA)  p. 3813
7.6.3A.1.1Test Purpose  p. 3813
7.6.3A.1.2Test Applicability  p. 3813
7.6.3A.1.3Minimum Conformance Requirements  p. 3813
7.6.3A.1.4Test Description  p. 3813
7.6.3A.1.5Test Requirement  p. 3816
7.6.3A.2Narrow band blocking for CA (intra-band contiguous DL CA without UL CA)  p. 3816
7.6.3A.2.4Test Description  p. 3817
7.6.3A.2.4.1Initial Conditions  p. 3817
7.6.3A.2.4.2Test Procedure  p. 3818
7.6.3A.2.4.3Message Contents  p. 3819
7.6.3A.2.5Test Requirement  p. 3819
7.6.3A.3Narrow band blocking for CA (inter-band DL CA without UL CA)  p. 3820
7.6.3A.3.4Test Description  p. 3820
7.6.3A.3.4.1Initial Conditions  p. 3820
7.6.3A.3.4.2Test Procedure  p. 3822
7.6.3A.3.4.3Message Contents  p. 3822
7.6.3A.3.5Test Requirement  p. 3822
7.6.3A.4Narrow band blocking for CA (intra-band non-contiguous DL CA without UL CA)  p. 3823
7.6.3A.4.4Test description  p. 3823
7.6.3A.4.4.1Initial Conditions  p. 3823
7.6.3A.4.4.2Test Procedure  p. 3823
7.6.3A.4.4.3Message Contents  p. 3824
7.6.3A.4.5Test Requirement  p. 3824
7.6.3A.5Narrow band blocking for 3DL CA  p. 3824
7.6.3A.5.1Test Purpose  p. 3824
7.6.3A.5.2Test Applicability  p. 3824
7.6.3A.5.3Minimum Conformance Requirements  p. 3824
7.6.3A.5.4Test Description  p. 3825
7.6.3A.5.4.1Initial Conditions  p. 3825
7.6.3A.5.4.2Test Procedure  p. 3830
7.6.3A.5.4.3Message Contents  p. 3831
7.6.3A.5.5Test Requirement  p. 3831
7.6.3A.6-  p. 3832
7.6.3A.7Narrow band blocking for 4DL CA  p. 3832
7.6.3A.7.1Test Purpose  p. 3832
7.6.3A.7.2Test Applicability  p. 3832
7.6.3A.7.3Minimum Conformance Requirements  p. 3832
7.6.3A.7.4Test Description  p. 3833
7.6.3A.7.4.1Initial Conditions  p. 3833
7.6.3A.7.4.2Test Procedure  p. 3842
7.6.3A.7.4.3Message Contents  p. 3843
7.6.3A.7.5Test Requirement  p. 3844
7.6.3A.8Narrow band blocking for 5DL CA  p. 3844
7.6.3A.8.1Test Purpose  p. 3844
7.6.3A.8.2Test Applicability  p. 3844
7.6.3A.8.3Minimum Conformance Requirements  p. 3844
7.6.3A.8.4Test Description  p. 3845
7.6.3A.8.4.1Initial Conditions  p. 3845
7.6.3A.8.4.2Test Procedure  p. 3853
7.6.3A.8.4.3Message Contents  p. 3856
7.6.3A.8.5Test Requirement  p. 3856
7.6.3A.9Narrow band blocking for 6DL CA  p. 3857
7.6.3A.9.1Test Purpose  p. 3857
7.6.3A.9.2Test Applicability  p. 3857
7.6.3A.9.3Minimum Conformance Requirements  p. 3857
7.6.3A.9.4Test Description  p. 3857
7.6.3A.9.4.1Initial Conditions  p. 3857
7.6.3A.9.4.2Test Procedure  p. 3876
7.6.3A.9.4.3Message Contents  p. 3880
7.6.3A.9.5Test Requirement  p. 3880
7.6.3A.10Narrow band blocking for 7DL CA  p. 3882
7.6.3A.10.1Test Purpose  p. 3882
7.6.3A.10.2Test Applicability  p. 3882
7.6.3A.10.3Minimum Conformance Requirements  p. 3882
7.6.3A.10.4Test Description  p. 3882
7.6.3A.10.4.1Initial Conditions  p. 3882
7.6.3BNarrow band blocking for UL-MIMO  p. 3887
7.6.3B.1Test Purpose  p. 3887
7.6.3B.2Test Applicability  p. 3887
7.6.3B.3Minimum Conformance Requirements  p. 3887
7.6.3B.4Test Description  p. 3887
7.6.3B.4.1Initial Conditions  p. 3887
7.6.3B.4.2Test Procedure  p. 3888
7.6.3B.4.3Message Contents  p. 3889
7.6.3B.5Test Requirement  p. 3889
7.6.3DNarrow band blocking for ProSe  p. 3889
7.6.3D.0Minimum conformance requirements  p. 3889
7.6.3D.1Narrow band blocking for ProSe Direct Discovery  p. 3890
7.6.3D.1.1Test Purpose  p. 3890
7.6.3D.1.2Test Applicability  p. 3890
7.6.3D.1.3Minimum Conformance Requirements  p. 3890
7.6.3D.1.4Test Description  p. 3891
7.6.3D.1.5Test Requirement  p. 3893
7.6.3D.2Narrow band blocking for ProSe Direct Communication  p. 3893
7.6.3D.2.1Test Purpose  p. 3893
7.6.3D.2.2Test Applicability  p. 3893
7.6.3D.2.3Minimum Conformance Requirements  p. 3894
7.6.3D.2.4Test Description  p. 3894
7.6.3D.2.5Test Requirement  p. 3894
7.6.3ENarrow band blocking for UE category 0  p. 3894
7.6.3E.1Test Purpose  p. 3894
7.6.3E.2Test Applicability  p. 3894
7.6.3E.3Minimum Conformance Requirements  p. 3894
7.6.3E.4Test Description  p. 3894
7.6.3E.4.1Initial Conditions  p. 3894
7.6.3E.4.2Test Procedure  p. 3895
7.6.3E.4.3Message Contents  p. 3895
7.6.3E.5Test Requirement  p. 3895
7.6.3EANarrow band blocking for UE Category M1  p. 3896
7.6.3EA.1Test Purpose  p. 3896
7.6.3EA.2Test Applicability  p. 3896
7.6.3EA.3Minimum Conformance Requirements  p. 3896
7.6.3EA.4Test Description  p. 3896
7.6.3EA.4.1Initial Conditions  p. 3896
7.6.3EA.4.2Test Procedure  p. 3897
7.6.3EA.4.3Message Contents  p. 3897
7.6.3EA.5Test Requirement  p. 3898
7.6.3EBNarrow band blocking for UE category 1bis  p. 3898
7.6.3EB.1Test Purpose  p. 3898
7.6.3EB.2Test Applicability  p. 3898
7.6.3EB.3Minimum Conformance Requirements  p. 3898
7.6.3EB.4Test Description  p. 3898
7.6.3EB.4.1Initial Conditions  p. 3898
7.6.3EB.4.2Test Procedure  p. 3899
7.6.3EB.4.3Message Contents  p. 3899
7.6.3EB.5Test Requirement  p. 3899
7.6.3ECNarrow band blocking for UE category M2  p. 3899
7.6.3EC.1Test purpose  p. 3899
7.6.3EC.2Test applicability  p. 3899
7.6.3EC.3Minimum conformance requirements  p. 3899
7.6.3EC.4Test description  p. 3900
7.6.3EC.4.1Initial conditions  p. 3900
7.6.3EC.4.2Test procedure  p. 3900
7.6.3EC.4.3Message contents  p. 3900
7.6.3EC.5Test requirement  p. 3900
7.7Spurious response  p. 3901
7.7.1Test Purpose  p. 3901
7.7.2Test Applicability  p. 3901
7.7.3Minimum Conformance Requirements  p. 3901
7.7.4Test Description  p. 3901
7.7.4.1Initial Conditions  p. 3901
7.7.4.2Test Procedure  p. 3901
7.7.4.3Message Contents  p. 3902
7.7.5Test Requirement  p. 3902
7.7_1Spurious response with 4 Rx antenna ports  p. 3903
7.7_1.1Test Purpose  p. 3903
7.7_1.2Test Applicability  p. 3903
7.7_1.3Minimum Conformance Requirements  p. 3903
7.7_1.4Test Description  p. 3903
7.7_1.4.1Initial Conditions  p. 3903
7.7_1.4.2Test Procedure  p. 3903
7.7_1.4.3Message Contents  p. 3903
7.7_1.5Test Requirement  p. 3903
7.7ASpurious response for CA  p. 3904
7.7A.0Minimum conformance requirements  p. 3904
7.7A.1Spurious response for CA (intra-band contiguous DL CA and UL CA)  p. 3905
7.7A.1.1Test Purpose  p. 3905
7.7A.1.2Test Applicability  p. 3905
7.7A.1.3Minimum Conformance Requirements  p. 3905
7.7A.1.4Test Description  p. 3906
7.7A.1.4.1Initial Conditions  p. 3906
7.7A.1.4.2Test Procedure  p. 3906
7.7A.1.4.3Message Contents  p. 3906
7.7A.1.5Test Requirement  p. 3907
7.7A.2Spurious response for CA (intra-band contiguous DL CA without UL CA)  p. 3908
7.7A.2.4Test Description  p. 3908
7.7A.2.4.1Initial Conditions  p. 3908
7.7A.2.4.2Test Procedure  p. 3908
7.7A.2.4.3Message Contents  p. 3908
7.7A.2.5Test Requirement  p. 3908
7.7A.3Spurious response for CA (inter-band DL CA without UL CA)  p. 3909
7.7A.3.4Test Description  p. 3909
7.7A.3.4.1Initial Conditions  p. 3909
7.7A.3.4.2Test Procedure  p. 3909
7.7A.3.4.3Message Contents  p. 3909
7.7A.3.5Test Requirement  p. 3910
7.7A.4Spurious response for CA (intra-band non-contiguous DL CA without UL CA)  p. 3910
7.7A.4.4Test Description  p. 3910
7.7A.4.4.1Initial Conditions  p. 3910
7.7A.4.4.2Test Procedure  p. 3910
7.7A.4.4.3Message Contents  p. 3911
7.7A.4.5Test Requirement  p. 3911
7.7A.5Spurious response for 3DL CA  p. 3912
7.7A.5.1Test Purpose  p. 3912
7.7A.5.2Test Applicability  p. 3912
7.7A.5.3Minimum Conformance Requirements  p. 3912
7.7A.5.4Test Description  p. 3912
7.7A.5.4.1Initial Conditions  p. 3912
7.7A.5.4.2Test Procedure  p. 3912
7.7A.5.4.3Message Contents  p. 3912
7.7A.5.5Test Requirement  p. 3912
7.7A.6-  p. 3913
7.7A.7Spurious response for 4DL CA  p. 3913
7.7A.7.1Test Purpose  p. 3913
7.7A.7.2Test Applicability  p. 3913
7.7A.7.3Minimum Conformance Requirements  p. 3913
7.7A.7.4Test Description  p. 3913
7.7A.7.4.1Initial Conditions  p. 3913
7.7A.7.4.2Test Procedure  p. 3914
7.7A.7.4.3Message Contents  p. 3914
7.7A.7.5Test Requirement  p. 3914
7.7A.8Spurious response for 5DL CA  p. 3915
7.7A.8.1Test Purpose  p. 3915
7.7A.8.2Test Applicability  p. 3915
7.7A.8.3Minimum Conformance Requirements  p. 3915
7.7A.8.4Test Description  p. 3915
7.7A.8.4.1Initial Conditions  p. 3915
7.7A.8.4.2Test Procedure  p. 3915
7.7A.8.4.3Message Contents  p. 3916
7.7A.8.5Test Requirement  p. 3916
7.7A.9Spurious response for 6DL CA  p. 3916
7.7A.9.1Test Purpose  p. 3916
7.7A.9.2Test Applicability  p. 3916
7.7A.9.3Minimum Conformance Requirements  p. 3916
7.7A.9.4Test Description  p. 3917
7.7A.9.4.1Initial Conditions  p. 3917
7.7A.9.4.2Test Procedure  p. 3917
7.7A.9.4.3Message Contents  p. 3917
7.7A.9.5Test Requirement  p. 3917
7.7A.10Spurious response for 7DL CA  p. 3918
7.7A.10.1Test Purpose  p. 3918
7.7A.10.2Test Applicability  p. 3918
7.7A.10.3Minimum Conformance Requirements  p. 3918
7.7A.10.4Test Description  p. 3918
7.7A.10.4.1Initial Conditions  p. 3918
7.7A.10.4.2Test Procedure  p. 3918
7.7A.10.4.3Message Contents  p. 3919
7.7A.10.5Test Requirement  p. 3919
7.7BSpurious response for UL-MIMO  p. 3920
7.7B.1Test Purpose  p. 3920
7.7B.2Test Applicability  p. 3920
7.7B.3Minimum Conformance Requirements  p. 3920
7.7B.4Test Description  p. 3920
7.7B.4.1Initial Conditions  p. 3920
7.7B.4.2Test Procedure  p. 3920
7.7B.4.3Message Contents  p. 3920
7.7B.5Test Requirement  p. 3921
7.7DSpurious response for ProSe  p. 3921
7.7D.0Minimum conformance requirements  p. 3921
7.7D.1Spurious response for ProSe Direct Discovery  p. 3922
7.7D.1.1Test Purpose  p. 3922
7.7D.1.2Test Applicability  p. 3922
7.7D.1.3Minimum Conformance Requirements  p. 3922
7.7D.1.4Test Description  p. 3922
7.7D.1.4.1Initial Conditions  p. 3922
7.7D.1.4.2Test Procedure  p. 3923
7.7D.1.4.3Message Contents  p. 3923
7.7D.1.5Test Requirement  p. 3924
7.7D.2Spurious response for ProSe Direct Communication  p. 3924
7.7D.2.1Test Purpose  p. 3925
7.7D.2.2Test Applicability  p. 3925
7.7D.2.3Minimum Conformance Requirements  p. 3925
7.7D.2.4Test Description  p. 3925
7.7D.2.4.1Initial Conditions  p. 3925
7.7D.2.4.2Test Procedure  p. 3925
7.7D.2.4.3Message Contents  p. 3925
7.7D.2.5Test Requirement  p. 3925
7.7ESpurious response for UE category 0  p. 3925
7.7E.1Test Purpose  p. 3925
7.7E.2Test Applicability  p. 3925
7.7E.3Minimum Conformance Requirements  p. 3925
7.7E.4Test Description  p. 3925
7.7E.4.1Initial Conditions  p. 3925
7.7E.4.2Test Procedure  p. 3926
7.7E.4.3Message Contents  p. 3926
7.7E.5Test Requirement  p. 3926
7.7EASpurious response for UE category M1  p. 3926
7.7EA.1Test Purpose  p. 3926
7.7EA.2Test Applicability  p. 3926
7.7EA.3Minimum Conformance Requirements  p. 3926
7.7EA.4Test Description  p. 3927
7.7EA.4.1Initial Conditions  p. 3927
7.7EA.4.2Test Procedure  p. 3927
7.7EA.4.3Message Contents  p. 3927
7.7EA.5Test Requirement  p. 3928
7.7EBSpurious response for UE Category 1bis  p. 3928
7.7EB.1Test Purpose  p. 3928
7.7EB.2Test Applicability  p. 3928
7.7EB.3Minimum Conformance Requirements  p. 3928
7.7EB.4Test Description  p. 3929
7.7EB.4.1Initial Conditions  p. 3929
7.7EB.4.2Test Procedure  p. 3929
7.7EB.4.3Message Contents  p. 3929
7.7EB.5Test Requirement  p. 3929
7.7ECSpurious response for UE category M2  p. 3929
7.7EC.1Test Purpose  p. 3929
7.7EC.2Test Applicability  p. 3929
7.7EC.3Minimum Conformance Requirements  p. 3929
7.7EC.4Test Description  p. 3930
7.7EC.4.1Initial Conditions  p. 3930
7.7EC.4.2Test Procedure  p. 3930
7.7EC.4.3Message Contents  p. 3930
7.7EC.5Test Requirement  p. 3930
7.7FSpurious response for category NB1 and NB2  p. 3931
7.7GSpurious response for V2X Communication  p. 3932
7.7G.1Spurious response for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 3932
7.7G.1.1Test Purpose  p. 3932
7.7G.1.2Test Applicability  p. 3932
7.7G.1.3Minimum Conformance Requirements  p. 3933
7.7G.1.4Test Description  p. 3933
7.7G.1.4.1Initial Conditions  p. 3933
7.7G.1.4.2Test Procedure  p. 3933
7.7G.1.4.3Message Contents  p. 3933
7.7G.1.5Test Requirement  p. 3933
7.7G.2Spurious response for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions  p. 3934
7.7G.2.1Test Purpose  p. 3934
7.7G.2.2Test applicability  p. 3934
7.7G.2.3Minimum conformance requirements  p. 3934
7.7G.2.4Test description  p. 3934
7.7G.2.4.1Initial conditions  p. 3934
7.7G.2.4.2Test Procedure  p. 3934
7.7G.2.4.3Message Contents  p. 3935
7.7G.2.5Test Requirement  p. 3935
7.7G.3Spurious response for V2X Communication / Intra-band contiguous multi-carrier operation  p. 3935
7.7G.3.1Test Purpose  p. 3935
7.7G.3.2Test applicability  p. 3935
7.7G.3.3Minimum conformance requirements  p. 3935
7.7G.3.4Test description  p. 3936
7.7G.3.4.1Initial conditions  p. 3936
7.7G.3.4.2Test Procedure  p. 3936
7.7G.3.4.3Message Contents  p. 3936
7.7G.3.5Test Requirement  p. 3936
7.8Intermodulation characteristics  p. 3937
7.8.1Wide band Intermodulation  p. 3937
7.8.1.1Test purpose  p. 3937
7.8.1.2Test applicability  p. 3937
7.8.1.3Minimum conformance requirements  p. 3937
7.8.1.4Test description  p. 3938
7.8.1.4.1Initial condition  p. 3938
7.8.1.4.2Test procedure  p. 3939
7.8.1.4.3Message contents  p. 3940
7.8.1.5Test requirements  p. 3940
7.8.1_1Wide band Intermodulation with 4 Rx antenna ports  p. 3941
7.8.1_1.1Test purpose  p. 3941
7.8.1_1.2Test applicability  p. 3941
7.8.1_1.3Minimum conformance requirements  p. 3941
7.8.1_1.4Test description  p. 3941
7.8.1_1.4.1Initial condition  p. 3941
7.8.1_1.4.2Test procedure  p. 3942
7.8.1_1.4.3Message contents  p. 3942
7.8.1_1.5Test requirements  p. 3942
7.8.1AWide band Intermodulation for CA  p. 3943
7.8.1A.0Minimum conformance requirements  p. 3943
7.8.1A.1Wideband intermodulation for CA (intra-band contiguous DL CA and UL CA)  p. 3946
7.8.1A.1.1Test purpose  p. 3946
7.8.1A.1.2Test applicability  p. 3946
7.8.1A.1.3Minimum conformance requirements  p. 3946
7.8.1A.1.4Test description  p. 3946
7.8.1A.1.4.1Initial condition  p. 3946
7.8.1A.1.4.2Test procedure  p. 3947
7.8.1A.1.4.3Message contents  p. 3948
7.8.1A.1.5Test requirements  p. 3949
7.8.1A.2Wideband intermodulation for CA (intra-band contiguous DL CA without UL CA)  p. 3950
7.8.1A.2.4Test description  p. 3950
7.8.1A.2.4.1Initial condition  p. 3950
7.8.1A.2.4.2Test procedure  p. 3952
7.8.1A.2.4.3Message contents  p. 3952
7.8.1A.2.5Test requirements  p. 3952
7.8.1A.3Wideband intermodulation for CA (inter-band DL CA without UL CA)  p. 3953
7.8.1A.3.4Test description  p. 3953
7.8.1A.3.4.1Initial condition  p. 3953
7.8.1A.3.4.2Test procedure  p. 3956
7.8.1A.3.4.3Message contents  p. 3956
7.8.1A.3.5Test requirements  p. 3956
7.8.1A.4Wideband intermodulation for CA (intra band non-contiguous DL CA without UL CA)  p. 3958
7.8.1A.4.4Test description  p. 3958
7.8.1A.4.4.1Initial condition  p. 3958
7.8.1A.4.4.2Test procedure  p. 3959
7.8.1A.4.4.3Message contents  p. 3959
7.8.1A.4.5Test requirements  p. 3959
7.8.1A.5Wideband intermodulation for 3DL CA  p. 3960
7.8.1A.5.1Test purpose  p. 3960
7.8.1A.5.2Test applicability  p. 3960
7.8.1A.5.3Minimum conformance requirements  p. 3960
7.8.1A.5.4Test description  p. 3960
7.8.1A.5.5Test requirement  p. 3966
7.8.1A.6-  p. 3969
7.8.1A.7Wideband intermodulation for 4DL CA  p. 3969
7.8.1A.7.1Test purpose  p. 3969
7.8.1A.7.2Test applicability  p. 3969
7.8.1A.7.3Minimum conformance requirements  p. 3969
7.8.1A.7.4Test description  p. 3969
7.8.1A.7.5Test requirement  p. 3980
7.8.1A.8Wideband intermodulation for 5DL CA  p. 3981
7.8.1A.8.1Test purpose  p. 3981
7.8.1A.8.2Test applicability  p. 3981
7.8.1A.8.3Minimum conformance requirements  p. 3981
7.8.1A.8.4Test description  p. 3981
7.8.1A.8.5Test requirement  p. 3991
7.8.1A.9Wideband intermodulation for 6DL CA  p. 3993
7.8.1A.9.1Test purpose  p. 3993
7.8.1A.9.2Test applicability  p. 3993
7.8.1A.9.3Minimum conformance requirements  p. 3993
7.8.1A.9.4Test description  p. 3993
7.8.1A.9.5Test requirement  p. 4014
7.8.1BWide band Intermodulation for UL-MIMO  p. 4016
7.8.1B.1Test purpose  p. 4016
7.8.1B.2Test applicability  p. 4016
7.8.1B.3Minimum conformance requirements  p. 4016
7.8.1B.4Test description  p. 4016
7.8.1B.4.1Initial condition  p. 4016
7.8.1B.4.2Test procedure  p. 4017
7.8.1B.4.3Message contents  p. 4018
7.8.1B.5Test requirements  p. 4018
7.8.1C-  p. 4019
7.8.1DWide band intermodulation for ProSe  p. 4019
7.8.1D.0Minimum conformance requirements  p. 4019
7.8.1D.1Wide band intermodulation for ProSe Direct Discovery  p. 4019
7.8.1D.1.1Test Purpose  p. 4020
7.8.1D.1.2Test Applicability  p. 4020
7.8.1D.1.3Minimum Conformance Requirements  p. 4020
7.8.1D.1.4Test Description  p. 4020
7.8.1D.1.5Test Requirement  p. 4022
7.8.1D.2Wide band intermodulation for ProSe Direct Communication  p. 4023
7.8.1D.2.1Test Purpose  p. 4023
7.8.1D.2.2Test Applicability  p. 4023
7.8.1D.2.3Minimum Conformance Requirements  p. 4023
7.8.1D.2.4Test Description  p. 4023
7.8.1D.2.5Test Requirement  p. 4023
7.8.1EWide band Intermodulation for UE category 0  p. 4023
7.8.1E.1Test purpose  p. 4023
7.8.1E.2Test applicability  p. 4023
7.8.1E.3Minimum conformance requirements  p. 4023
7.8.1E.4Test description  p. 4023
7.8.1E.4.1Initial condition  p. 4023
7.8.1E.4.2Test procedure  p. 4024
7.8.1E.4.3Message contents  p. 4024
7.8.1E.5Test requirements  p. 4024
7.8.1EAWide band Intermodulation for UE category M1  p. 4025
7.8.1EA.1Test purpose  p. 4025
7.8.1EA.2Test applicability  p. 4025
7.8.1EA.3Minimum conformance requirements  p. 4025
7.8.1EA.4Test description  p. 4026
7.8.1EA.4.1Initial condition  p. 4026
7.8.1EA.4.2Test procedure  p. 4027
7.8.1EA.4.3Message contents  p. 4027
7.8.1EA.5Test requirements  p. 4027
7.8.1EBWide band Intermodulation for UE category 1bis  p. 4028
7.8.1EB.1Test purpose  p. 4028
7.8.1EB.2Test applicability  p. 4028
7.8.1EB.3Minimum conformance requirements  p. 4028
7.8.1EB.4Test description  p. 4028
7.8.1EB.4.1Initial condition  p. 4028
7.8.1EB.4.2Test procedure  p. 4028
7.8.1EB.4.3Message contents  p. 4028
7.8.1EB.5Test requirements  p. 4028
7.8.1ECWide band intermodulation for UE category M2  p. 4029
7.8.1EC.1Test purpose  p. 4029
7.8.1EC.2Test applicability  p. 4029
7.8.1EC.3Minimum conformance requirements  p. 4029
7.8.1EC.4Test description  p. 4030
7.8.1EC.4.1Initial conditions  p. 4030
7.8.1EC.4.2Test procedure  p. 4030
7.8.1EC.4.3Message contents  p. 4031
7.8.1EC.5Test requirement  p. 4031
7.8.1FWide band Intermodulation for category NB1 and NB2  p. 4031
7.8.1GWide band Intermodulation for V2X Communication  p. 4033
7.8.1G.1Wide band Intermodulation for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 4033
7.8.1G.1.1Test Purpose  p. 4033
7.8.1G.1.2Test Applicability  p. 4033
7.8.1G.1.3Minimum Conformance Requirements  p. 4033
7.8.1G.1.4Test Description  p. 4034
7.8.1G.1.4.1Initial Conditions  p. 4034
7.8.1G.1.4.2Test Procedure  p. 4034
7.8.1G.1.4.3Message Contents  p. 4035
7.8.1G.1.5Test Requirement  p. 4035
7.8.1G.2Wide band Intermodulation for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions  p. 4035
7.8.1G.2.1Test Purpose  p. 4035
7.8.1G.2.2Test Applicability  p. 4035
7.8.1G.2.3Minimum Conformance Requirements  p. 4035
7.8.1G.2.4Test Description  p. 4036
7.8.1G.2.4.1Initial Conditions  p. 4036
7.8.1G.2.4.2Test Procedure  p. 4037
7.8.1G.2.4.3Message Contents  p. 4038
7.8.1G.2.5Test Requirement  p. 4038
7.8.1G.3Wide band Intermodulation for V2X Communication / Intra-band contiguous multi-carrier operation  p. 4038
7.8.1G.3.1Test Purpose  p. 4038
7.8.1G.3.2Test Applicability  p. 4038
7.8.1G.3.3Minimum Conformance Requirements  p. 4038
7.8.1G.3.4Test Description  p. 4039
7.8.1G.3.4.1Initial Conditions  p. 4039
7.8.1G.3.4.2Test Procedure  p. 4040
7.8.1G.3.4.3Message Contents  p. 4040
7.8.1G.3.5Test Requirement  p. 4040
7.8.2Void  p. …
7.9Spurious emissions  p. 4040
7.9.1Test Purpose  p. 4040
7.9.2Test Applicability  p. 4041
7.9.3Minimum Conformance Requirements  p. 4041
7.9.4Test Description  p. 4041
7.9.4.1Initial Conditions  p. 4041
7.9.4.2Test Procedure  p. 4042
7.9.4.3Message Contents  p. 4042
7.9.5Test Requirement  p. 4042
7.9_1Spurious emissions with 4 Rx antenna ports  p. 4042
7.9_1.1Test Purpose  p. 4042
7.9_1.2Test Applicability  p. 4042
7.9_1.3Minimum Conformance Requirements  p. 4042
7.9_1.4Test Description  p. 4042
7.9_1.4.1Initial Conditions  p. 4042
7.9_1.4.2Test Procedure  p. 4043
7.9_1.4.3Message Contents  p. 4043
7.9_1.5Test Requirement  p. 4043
7.9ASpurious emissions for CA  p. 4043
7.9A.1Test Purpose  p. 4043
7.9A.2Test Applicability  p. 4044
7.9A.3Minimum Conformance Requirements  p. 4044
7.9A.4Test Description  p. 4044
7.9A.4.1Initial Conditions  p. 4044
7.9A.4.2Test Procedure  p. 4045
7.9A.4.3Message Contents  p. 4046
7.9A.5Test Requirement  p. 4046
7.9ESpurious emissions for UE category 0  p. 4046
7.9E.1Test Purpose  p. 4046
7.9E.2Test Applicability  p. 4046
7.9E.3Minimum Conformance Requirements  p. 4046
7.9E.4Test Description  p. 4046
7.9E.4.1Initial Conditions  p. 4046
7.9E.4.2Test Procedure  p. 4047
7.9E.4.3Message Contents  p. 4047
7.9E.5Test Requirement  p. 4047
7.9EASpurious emissions for UE category M1  p. 4047
7.9EA.1Test Purpose  p. 4047
7.9EA.2Test Applicability  p. 4047
7.9EA.3Minimum Conformance Requirements  p. 4048
7.9EA.4Test Description  p. 4048
7.9EA.4.1Initial Conditions  p. 4048
7.9EA.4.2Test Procedure  p. 4049
7.9EA.4.3Message Contents  p. 4049
7.9EA.5Test Requirement  p. 4049
7.9EBSpurious emissions for UE Category 1bis  p. 4049
7.9EB.1Test Purpose  p. 4049
7.9EB.2Test Applicability  p. 4049
7.9EB.3Minimum Conformance Requirements  p. 4049
7.9EB.4Test Description  p. 4049
7.9EB.4.1Initial Conditions  p. 4049
7.9EB.4.2Test Procedure  p. 4049
7.9EB.4.3Message Contents  p. 4049
7.9EB.5Test Requirement  p. 4050
7.9ECSpurious emissions for UE category M2  p. 4050
7.9EC.1Test Purpose  p. 4050
7.9EC.2Test Applicability  p. 4050
7.9EC.3Minimum Conformance Requirements  p. 4050
7.9EC.4Test Description  p. 4050
7.9EC.4.1Initial Conditions  p. 4050
7.9EC.4.2Test Procedure  p. 4051
7.9EC.4.3Message Contents  p. 4051
7.9EC.5Test Requirement  p. 4051
7.9FSpurious emissions for Category NB1  p. 4051
7.9GSpurious emissions for V2X Communication  p. 4053
7.9G.1Spurious emissions for V2X Communication / Non-concurrent with E-UTRA uplink transmissions  p. 4053
7.9G.1.1Test Purpose  p. 4053
7.9G.1.2Test Applicability  p. 4053
7.9G.1.3Minimum Conformance Requirements  p. 4053
7.9G.1.4Test Description  p. 4054
7.9G.1.4.1Initial Conditions  p. 4054
7.9G.1.4.2Test Procedure  p. 4054
7.9G.1.4.3Message Contents  p. 4054
7.9G.1.5Test Requirement  p. 4055
7.10Void  p. …
7.10AReceiver image for CA  p. 4055
7.10GReceiver image for V2X  p. 4055
8Performance Requirement  p. 4056
8.1General  p. 4056
8.1.1Receiver antenna capability  p. 4056
8.1.1.1Simultaneous unicast and MBMS operations  p. 4057
8.1.1.2Dual-antenna receiver capability in idle mode  p. 4057
8.1.2Applicability of requirements  p. 4057
8.1.2.1Applicability of requirements for different channel bandwidths  p. 4057
8.1.2.2Definition of CA capability  p. 4057
8.1.2.2ADefinition of dual connectivity capability  p. 4063
8.1.2.3Applicability and test rules for different CA configurations and bandwidth combination sets  p. 4063
8.1.2.3AApplicability and test rules for different dual connectivity configuration and bandwidth combination set  p. 4066
8.1.2.3BApplicability and test rules for different TDD-FDD CA configurations and bandwidth combination sets  p. 4066
8.1.2.3DApplicability and test rules for different CA with LAA SCell(s) configurations and bandwidth combination sets  p. 4068
8.1.2.4Test coverage for different number of component carriers  p. 4069
8.1.2.6Applicability of performance requirements for 4Rx capable UEs  p. 4070
8.1.2.6.1Applicability rule and antenna connection for single carrier tests with 2Rx  p. 4070
8.1.2.6.2Applicability rule and antenna connection for CA and DC tests with 2Rx  p. 4072
8.1.2.6.3Applicability rule and antenna connection for single carrier tests with 4Rx  p. 4072
8.1.2.6.4Applicability rule for 256QAM tests  p. 4072
8.1.2.6.5Applicability rule and antenna connection for CA and DC tests with 4Rx  p. 4073
8.1.2.6.6Applicability rule for Type C with 4Rx  p. 4076
8.1.2.7Applicability of Enhanced Downlink Control Channel Performance Requirements  p. 4076
8.1.2.8-  p. 4077
8.1.2.8AApplicability of performance requirements for UE supporting coverage enhancement  p. 4077
8.2Demodulation of PDSCH (Cell-Specific Reference Symbols)  p. 4078
8.2.1FDD (Fixed Reference Channel)  p. 4078
8.2.1.1FDD PDSCH Single Antenna Port Performance (Cell-Specific Reference Symbols)  p. 4079
8.2.1.1.1FDD PDSCH Single Antenna Port Performance  p. 4079
8.2.1.1.1_1FDD PDSCH Single Antenna Port Performance (Release 9 and forward)  p. 4083
8.2.1.1.1_2FDD PDSCH Single Antenna Port Performance (Release 10 and forward)  p. 4085
8.2.1.1.1_AFDD PDSCH Single Antenna Port Performance for CA  p. 4087
8.2.1.1.1_A.1FDD PDSCH Single Antenna Port Performance for CA (2DL CA)  p. 4087
8.2.1.1.1_A.2FDD PDSCH Single Antenna Port Performance for CA (3DL CA)  p. 4090
8.2.1.1.1_A.3Void  p. …
8.2.1.1.1_A.4FDD PDSCH Single Antenna Port Performance for CA (4DL CA)  p. 4094
8.2.1.1.1_A.5FDD PDSCH Single Antenna Port Performance for CA (5 DL CA)  p. 4098
8.2.1.1.1_A.6FDD PDSCH Single Antenna Port Performance for CA (6 DL CA)  p. 4102
8.2.1.1.1_A.7FDD PDSCH Single Antenna Port Performance for CA (7 DL CA)  p. 4105
8.2.1.1.2FDD PDSCH Single Antenna Port Performance with 1 PRB in presence of MBSFN  p. 4108
8.2.1.2FDD PDSCH Transmit Diversity Performance (Cell-Specific Reference Symbols)  p. 4110
8.2.1.2.1FDD PDSCH Transmit Diversity 2x2  p. 4110
8.2.1.2.1_1FDD PDSCH Transmit Diversity 2x2 (Release 9 and forward)  p. 4113
8.2.1.2.2FDD PDSCH Transmit Diversity 4x2  p. 4114
8.2.1.2.2_1FDD PDSCH Transmit Diversity 4x2 (Release 9 and forward)  p. 4116
8.2.1.2.3-  p. 4117
8.2.1.2.3_CFDD PDSCH Transmit diversity 2x2 for eICIC  p. 4117
8.2.1.2.3_C.1FDD PDSCH Transmit diversity 2x2 for eICIC (non-MBSFN ABS)  p. 4117
8.2.1.2.3_D-  p. 4122
8.2.1.2.3_EFDD PDSCH Transmit diversity 2x2 for feICIC  p. 4122
8.2.1.2.3_E.1FDD PDSCH Transmit diversity 2x2 for feICIC (non-MBSFN ABS)  p. 4122
8.2.1.2.4FDD PDSCH Transmit Diversity 2x2 with TM3 Interference Model - Enhanced Performance Requirement Type A  p. 4128
8.2.1.2.5FDD PDSCH Transmit Diversity 2x2 with TM2 Interference Model - Enhanced Performance Requirement Type B  p. 4132
8.2.1.2.6FDD PDSCH Transmit Diversity 2x2 with TM9 Interference Model - Enhanced Performance Requirement Type B  p. 4135
8.2.1.3FDD PDSCH Open Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols)  p. 4139
8.2.1.3.1FDD PDSCH Open Loop Spatial Multiplexing 2x2  p. 4139
8.2.1.3.1_1FDD PDSCH Open Loop Spatial Multiplexing 2x2 (Release 11 and forward)  p. 4141
8.2.1.3.1_AFDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA  p. 4143
8.2.1.3.1_A.1FDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA (2DL CA)  p. 4143
8.2.1.3.1_A.2FDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA (3DL CA)  p. 4147
8.2.1.3.1_A.3FDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA (4DL CA)  p. 4151
8.2.1.3.1_A.4FDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA (5DL CA)  p. 4155
8.2.1.3.1_A.5FDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA (6DL CA)  p. 4159
8.2.1.3.1_A.6FDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA (7DL CA)  p. 4163
8.2.1.3.1AFDD Soft buffer management test  p. 4166
8.2.1.3.1A_A.1FDD PDSCH Soft buffer management test for CA (2 DL CA)  p. 4166
8.2.1.3.1A_A.2Void  p. …
8.2.1.3.1BFDD PDSCH Open Loop Spatial Multiplexing 2x2 - Enhanced Performance Requirement Type C  p. 4170
8.2.1.3.2FDD PDSCH Open Loop Spatial Multiplexing 4x2  p. 4176
8.2.1.3.3_CFDD PDSCH Open Loop Spatial Multiplexing 2x2 for eICIC  p. 4178
8.2.1.3.3_C.1FDD PDSCH Open Loop Spatial Multiplexing 2x2 for eICIC (non-MBSFN ABS)  p. 4178
8.2.1.3.3_C.2FDD PDSCH Open Loop Spatial Multiplexing 2x2 for eICIC (MBSFN ABS)  p. 4184
8.2.1.3.3_D-  p. 4190
8.2.1.3.3_EFDD PDSCH Open Loop Spatial Multiplexing 2x2 for feICIC  p. 4190
8.2.1.3.3_E.1FDD PDSCH Open Loop Spatial Multiplexing 2x2 for feICIC (demodulation subframe overlaps with aggressor cell ABS and CRS assistance information are configured, non-MBSFN ABS)  p. 4190
8.2.1.4FDD PDSCH Closed Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols)  p. 4197
8.2.1.4.1FDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 2x2  p. 4197
8.2.1.4.1_1FDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 2x2 (Release 9 and forward)  p. 4201
8.2.1.4.1_A_to_D-  p. 4203
8.2.1.4.1_EFDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 2x2 for feICIC  p. 4203
8.2.1.4.1_E.1FDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 2x2 for feICIC (non-MBSFN ABS)  p. 4203
8.2.1.4.1_HFDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 2x2 for 256QAM in DL  p. 4210
8.2.1.4.2AFDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 2x2 - Enhanced Performance Requirement Type C  p. 4213
8.2.1.4.2FDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 4x2  p. 4215
8.2.1.4.2_1FDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 4x2 (Release 9 and forward)  p. 4220
8.2.1.4.2_AFDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA  p. 4221
8.2.1.4.2_A.1FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA (2DL CA)  p. 4221
8.2.1.4.2_A.2FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA (3DL CA)  p. 4227
8.2.1.4.2_A.3FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA (4DL CA)  p. 4233
8.2.1.4.2_A.4FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA (5DL CA)  p. 4237
8.2.1.4.2_A.5FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA (6DL CA)  p. 4240
8.2.1.4.2_A.6FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA (7DL CA)  p. 4243
8.2.1.4.3FDD PDSCH Closed Loop Single Layer Spatial Multiplexing 2x2 with TM4 Interference Model - Enhanced Performance Requirement Type A  p. 4246
8.2.1.4.3AFDD PDSCH Closed Loop Multi-Layer Spatial Multiplexing 4x2 for Dual Connectivity  p. 4251
8.2.1.4.4FDD PDSCH Closed Loop Single Layer Spatial Multiplexing 2x2 with TM4 Interference Model - Enhanced Performance Requirement Type B  p. 4255
8.2.1.5-  p. 4259
8.2.1.6-  p. 4259
8.2.1.7Carrier aggregation with power imbalance  p. 4259
8.2.1.7_A.1FDD Carrier aggregation with power imbalance (intra-band contiguous DL CA)  p. 4259
8.2.1.8FFS  p. 4262
8.2.1.9FDD PDSCH performance in HST-SFN scenario  p. 4262
8.2.1.10Intra-band contiguous carrier aggregation with minimum channel spacing (3DL CA)  p. 4264
8.2.1.10.5Test requirement  p. 4266
8.2.2TDD (Fixed Reference Channel)  p. 4266
8.2.2.1TDD PDSCH Single Antenna Port Performance (Cell-Specific Reference Symbols)  p. 4268
8.2.2.1.1TDD PDSCH Single Antenna Port Performance  p. 4268
8.2.2.1.1_1TDD PDSCH Single Antenna Port Performance (Release 9 and forward)  p. 4271
8.2.2.1.1_2TDD PDSCH Single Antenna Port Performance (Release 10 and forward)  p. 4273
8.2.2.1.1_ATDD PDSCH Single Antenna Port Performance for CA  p. 4275
8.2.2.1.1_A.1TDD PDSCH Single Antenna Port Performance for CA (2DL CA)  p. 4275
8.2.2.1.1_A.2TDD PDSCH Single Antenna Port Performance for CA (3DL CA)  p. 4278
8.2.2.1.1_A.3TDD PDSCH Single Antenna Port Performance for CA (4DL CA)  p. 4281
8.2.2.1.1_A.4TDD PDSCH Single Antenna Port Performance for CA (5DL CA)  p. 4283
8.2.2.1.1_A.5TDD PDSCH Single Antenna Port Performance for CA (6DL CA)  p. 4286
8.2.2.1.1_A.6TDD PDSCH Single Antenna Port Performance for CA (7DL CA)  p. 4288
8.2.2.1.2TDD PDSCH Single Antenna Port Performance with 1 PRB in the presence of MBSFN  p. 4291
8.2.2.2TDD PDSCH Transmit Diversity Performance (Cell-Specific Reference Symbols)  p. 4293
8.2.2.2.1TDD PDSCH Transmit Diversity 2x2  p. 4293
8.2.2.2.1_1TDD PDSCH Transmit Diversity 2x2 (Release 9 and forward)  p. 4295
8.2.2.2.2TDD PDSCH Transmit Diversity 4x2  p. 4296
8.2.2.2.2_1TDD PDSCH Transmit Diversity 4x2 (Release 9 and forward)  p. 4298
8.2.2.2.3_CTDD PDSCH Transmit diversity 2x2 for eICIC  p. 4299
8.2.2.2.3_C.1TDD PDSCH Transmit diversity 2x2 for eICIC (non-MBSFN ABS)  p. 4299
8.2.2.2.3_D-  p. 4304
8.2.2.2.3_ETDD PDSCH Transmit diversity 2x2 for feICIC  p. 4304
8.2.2.2.3_E.1TDD PDSCH Transmit diversity 2x2 for feICIC (non-MBSFN ABS)  p. 4304
8.2.2.2.4TDD PDSCH Transmit Diversity 2x2 with TM3 Interference Model - Enhanced Performance Requirement Type A  p. 4310
8.2.2.2.5TDD PDSCH Transmit Diversity 2x2 for eIMTA(when EIMTA-MainConfigServCell-r12 is configured)  p. 4315
8.2.2.2.6TDD PDSCH Transmit Diversity 2x2 with TM2 Interference Model - Enhanced Performance Requirement Type B  p. 4317
8.2.2.2.7TDD PDSCH Transmit Diversity 2x2 with TM9 Interference Model - Enhanced Performance Requirement Type B  p. 4321
8.2.2.3TDD PDSCH Open Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols)  p. 4325
8.2.2.3.1TDD PDSCH Open Loop Spatial Multiplexing 2x2  p. 4325
8.2.2.3.1_1TDD PDSCH Open Loop Spatial Multiplexing 2x2 (Release 11 and forward)  p. 4327
8.2.2.3.1_ATDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA  p. 4328
8.2.2.3.1_A.1TDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA (2DL CA)  p. 4328
8.2.2.3.1_A.2TDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA (3DL CA)  p. 4332
8.2.2.3.1_A.3TDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA (4DL CA)  p. 4336
8.2.2.3.1_A.4TDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA (5DL CA)  p. 4339
8.2.2.3.1_A.5TDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA (6DL CA)  p. 4342
8.2.2.3.1_A.6TDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA (7DL CA)  p. 4344
8.2.2.3.1ATDD Soft buffer management test  p. 4345
8.2.2.3.1A_A.1TDD PDSCH Soft buffer management test for CA (2 DL CA)  p. 4345
8.2.2.3.1A_A.2Void  p. …
8.2.2.3.1A_A.3Void  p. …
8.2.2.3.1BTDD PDSCH Open Loop Spatial Multiplexing 2x2 - Enhanced Performance Requirement Type C  p. 4348
8.2.2.3.1B.1Test purpose  p. 4348
8.2.2.3.1B.2Test applicability  p. 4348
8.2.2.3.1B.3Minimum conformance requirements  p. 4348
8.2.2.3.1B.4Test description  p. 4349
8.2.2.3.1B.5Test requirement  p. 4350
8.2.2.3.1C.1Test purpose  p. 4350
8.2.2.3.1C.2Test applicability  p. 4350
8.2.2.3.1C.3Minimum conformance requirements  p. 4351
8.2.2.3.1C.4Test description  p. 4351
8.2.2.3.1C.4.1Initial conditions  p. 4351 Initial conditions
8.2.2.3.1C.4.2Test procedure  p. 4352
8.2.2.3.1C.4.3Message contents  p. 4352
8.2.2.3.1C.5Test requirement  p. 4352
8.2.2.3.2TDD PDSCH Open Loop Spatial Multiplexing 4x2  p. 4353
8.2.2.3.3_CTDD PDSCH Open Loop Spatial Multiplexing 2x2 for eICIC  p. 4356
8.2.2.3.3_C.1TDD PDSCH Open Loop Spatial Multiplexing 2x2 for eICIC (non-MBSFN ABS)  p. 4356
8.2.2.3.3_C.2TDD PDSCH Open Loop Spatial Multiplexing 2x2 for eICIC (MBSFN ABS)  p. 4362
8.2.2.3.3_D-  p. 4368
8.2.2.3.3_ETDD PDSCH Open Loop Spatial Multiplexing 2x2 for feICIC  p. 4368
8.2.2.3.3_E.1TDD PDSCH Open Loop Spatial Multiplexing 2x2 for feICIC (demodulation subframe overlaps with aggressor cell ABS and CRS assistance information are configured, non-MBSFN ABS)  p. 4368
8.2.2.4TDD PDSCH Closed Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols)  p. 4375
8.2.2.4.1TDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 2x2  p. 4375
8.2.2.4.1_1TDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 2x2 (Release 9 and forward)  p. 4379
8.2.2.4.1_A_to_D-  p. 4381
8.2.2.4.1_ETDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 2x2 for feICIC  p. 4381
8.2.2.4.1_E.1TDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 2x2 for feICIC (non-MBSFN ABS)  p. 4381
8.2.2.4.1_HTDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 2x2 for 256QAM in DL  p. 4389
8.2.2.4.2TDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 4x2  p. 4392
8.2.2.4.2_1TDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 4x2 (Release 9 and forward)  p. 4397
8.2.2.4.2_ATDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA  p. 4398
8.2.2.4.2_A.1TDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA (2DL CA)  p. 4398
8.2.2.4.2_A.2TDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA (3DL CA)  p. 4403
8.2.2.4.2_A.3TDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA (4DL CA)  p. 4409
8.2.2.4.2_A.4TDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA (5DL CA)  p. 4414
8.2.2.4.2ATDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 2x2 - Enhanced Performance Requirement Type C  p. 4418
8.2.2.4.3TDD PDSCH Closed Loop Single Layer Spatial Multiplexing 2x2 with TM4 Interference Model - Enhanced Performance Requirement Type A  p. 4421
8.2.2.4.4TDD PDSCH Closed Loop Multi-Layer Spatial Multiplexing 4x2 for Dual Connectivity  p. 4426
8.2.2.4.5TDD PDSCH Closed Loop Single Layer Spatial Multiplexing 2x2 with TM4 Interference Model - Enhanced Performance Requirement Type B  p. 4430
8.2.2.5-  p. 4435
8.2.2.6-  p. 4435
8.2.2.7Carrier aggregation with power imbalance  p. 4435
8.2.2.7_A.1TDD Carrier aggregation with power imbalance (intra-band contiguous DL CA)  p. 4435
8.2.2.8Intra-band contiguous carrier aggregation with minimum channel spacing  p. 4438
8.2.2.8.1Intra-band contiguous carrier aggregation with minimum channel spacing (2DL CA)  p. 4438
8.2.2.8.2Intra-band contiguous carrier aggregation with minimum channel spacing (3DL CA)  p. 4440
8.2.2.9TDD PDSCH HST-SFN performance in HST-SFN scenario  p. 4442
8.2.3TDD FDD CA (Fixed Reference Channel)  p. 4444
8.2.3.1TDD FDD CA PDSCH Single Antenna Port Performance  p. 4445
8.2.3.1.1-  p. 4445
8.2.3.1.1.1TDD FDD CA PDSCH Single Antenna Port Performance for FDD PCell (2DL CA)  p. 4445
8.2.3.1.1.2TDD FDD CA PDSCH Single Antenna Port Performance for FDD PCell (3DL CA)  p. 4450
8.2.3.1.1.3TDD FDD CA PDSCH Single Antenna Port Performance for FDD PCell (4DL CA)  p. 4454
8.2.3.1.1.4TDD FDD CA PDSCH Single Antenna Port Performance for FDD PCell (5DL CA)  p. 4458
8.2.3.1.1.5TDD FDD CA PDSCH Single Antenna Port Performance for FDD PCell (6DL CA)  p. 4462
8.2.3.1.1.6TDD FDD CA PDSCH Single Antenna Port Performance for FDD PCell (7DL CA)  p. 4466
8.2.3.1.2.1TDD FDD CA PDSCH Single Antenna Port Performance for TDD PCell (2DL CA)  p. 4469
8.2.3.1.2.2TDD FDD CA PDSCH Single Antenna Port Performance for TDD PCell (3DL CA)  p. 4473
8.2.3.1.2.3TDD FDD CA PDSCH Single Antenna Port Performance for TDD PCell (4DL CA)  p. 4477
8.2.3.1.2.4TDD FDD CA PDSCH Single Antenna Port Performance for TDD PCell (5DL CA)  p. 4481
8.2.3.1.2.5TDD FDD CA PDSCH Single Antenna Port Performance for TDD PCell (6DL CA)  p. 4485
8.2.3.1.2.6TDD FDD CA PDSCH Single Antenna Port Performance for TDD PCell (7DL CA)  p. 4489
8.2.3.2TDD FDD CA PDSCH Open Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols)  p. 4492
8.2.3.2.1TDD FDD CA PDSCH Open Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols) for FDD PCell  p. 4492
8.2.3.2.1.1TDD FDD CA PDSCH Open Loop Spatial Multiplexing 2x2 for FDD PCell (2DL CA)  p. 4492
8.2.3.2.1.2TDD FDD CA PDSCH Open Loop Spatial Multiplexing 2x2 for FDD PCell (3DL CA)  p. 4497
8.2.3.2.1ATDD FDD CA PDSCH Soft buffer management test for FDD PCell (2DL CA)  p. 4500
8.2.3.2.1.3TDD FDD CA PDSCH Open Loop Spatial Multiplexing 2x2 for FDD PCell (4DL CA)  p. 4504
8.2.3.2.1.4TDD FDD CA PDSCH Open Loop Spatial Multiplexing 2x2 for FDD PCell (5DL CA)  p. 4507
8.2.3.2.1.5TDD FDD CA PDSCH Open Loop Spatial Multiplexing 2x2 for FDD PCell (6DL CA)  p. 4510
8.2.3.2.1.6TDD FDD CA PDSCH Open Loop Spatial Multiplexing 2x2 for FDD PCell (7DL CA)  p. 4513
8.2.3.2.2TDD FDD CA PDSCH Open Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols) for TDD PCell  p. 4516
8.2.3.2.2.1TDD FDD CA PDSCH Open Loop Spatial Multiplexing 2x2 for TDD PCell (2DL CA)  p. 4516
8.2.3.2.2.2TDD FDD CA PDSCH Open Loop Spatial Multiplexing 2x2 for TDD PCell (3DL CA)  p. 4521
8.2.3.2.2.3TDD FDD CA PDSCH Open Loop Spatial Multiplexing 2x2 for TDD PCell (4DL CA)  p. 4524
8.2.3.2.2.4TDD FDD CA PDSCH Open Loop Spatial Multiplexing 2x2 for TDD PCell (5DL CA)  p. 4528
8.2.3.2.2.5TDD FDD CA PDSCH Open Loop Spatial Multiplexing 2x2 for TDD PCell (6DL CA)  p. 4531
8.2.3.2.2.6TDD FDD CA PDSCH Open Loop Spatial Multiplexing 2x2 for TDD PCell (7DL CA)  p. 4534
8.2.3.2.2ATDD FDD CA PDSCH Soft buffer management test for TDD PCell (2DL CA)  p. 4537
8.2.3.3TDD FDD CA PDSCH Closed Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols)  p. 4542
8.2.3.3.1TDD FDD CA PDSCH Closed Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols) for FDD PCell  p. 4542
8.2.3.3.1.1TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for FDD PCell (2DL CA)  p. 4542
8.2.3.3.1.2TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for FDD PCell (3DL CA)  p. 4548
8.2.3.3.1.3TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for FDD PCell (4DL CA)  p. 4552
8.2.3.3.1.4TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for FDD PCell (5DL CA)  p. 4556
8.2.3.3.1.5TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for FDD PCell (6DL CA)  p. 4559
8.2.3.3.1.6TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for FDD PCell (7DL CA)  p. 4562
8.2.3.3.2TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for TDD PCell  p. 4565
8.2.3.3.2.1TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for TDD PCell (2DL CA)  p. 4565
8.2.3.3.2.2TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for TDD PCell (3DL CA)  p. 4572
8.2.3.3.2.3TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for TDD PCell (4DL CA)  p. 4574
8.2.3.3.2.4TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for TDD PCell (5DL CA)  p. 4578
8.2.3.3.2.5TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for TDD PCell (6DL CA)  p. 4582
8.2.3.3.2.6TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for TDD PCell (7DL CA)  p. 4585
8.2.4LAA  p. 4588
8.2.4.1LAA PDSCH CA Closed-Loop Spatial Multiplexing Performance  p. 4588
8.2.4.1.1LAA PDSCH CA Closed Loop Spatial Multiplexing Performance with 4 Tx Antenna port and with FDD as Pcell (FDD single carrier)  p. 4588
8.2.4.1.1.1Test purpose  p. 4588
8.2.4.1.1.2Test applicability  p. 4588
8.2.4.1.1.3Minimum conformance requirements  p. 4588
8.2.4.1.1.4Test description  p. 4591
8.2.4.1.1.5Test requirement  p. 4595
8.2.4.1.2LAA PDSCH CA Closed Loop Spatial Multiplexing Performance with 4 Tx Antenna port and with TDD as Pcell (TDD single carrier)  p. 4596
8.2.4.1.2.1Test purpose  p. 4596
8.2.4.1.2.2Test applicability  p. 4596
8.2.4.1.2.3Minimum conformance requirements  p. 4596
8.2.4.1.2.4Test description  p. 4599
8.2.4.1.2.5Test requirement  p. 4603
8.3Demodulation of PDSCH (User-Specific Reference Symbols)  p. 4604
8.3.1FDD  p. 4604
8.3.1.1FDD PDSCH Single-layer Spatial Multiplexing Performance (UE-Specific Reference Symbols)  p. 4605
8.3.1.1.1_DFDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 without a simultaneous transmission for eDL-MIMO  p. 4605
8.3.1.1.1_D.1Test purpose  p. 4605
8.3.1.1.1_D.2Test applicability  p. 4605
8.3.1.1.1_D.3Minimum conformance requirements  p. 4605
8.3.1.1.1_D.4Test description  p. 4606
8.3.1.1.1_D.5Test requirement  p. 4608
8.3.1.1.1_HFDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 without a simultaneous transmission for eDL-MIMO for 256QAM in DL  p. 4609
8.3.1.1.1_H.1Test purpose  p. 4609
8.3.1.1.1_H.2Test applicability  p. 4609
8.3.1.1.1_H.3Minimum conformance requirements  p. 4609
8.3.1.1.1_H.4Test description  p. 4609
8.3.1.1.2_DFDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 with a simultaneous transmission for eDL-MIMO  p. 4610
8.3.1.1.2_D.1Test purpose  p. 4610
8.3.1.1.2_D.2Test applicability  p. 4610
8.3.1.1.2_D.3Minimum conformance requirements  p. 4610
8.3.1.1.2_D.4Test description  p. 4612
8.3.1.1.3FDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 with TM9 Interference Model - Enhanced Performance Requirement Type A  p. 4615
8.3.1.1.3.1Test purpose  p. 4615
8.3.1.1.3.2Test applicability  p. 4615
8.3.1.1.3.3Minimum conformance requirements  p. 4615
8.3.1.1.3.4Test description  p. 4617
8.3.1.1.4FDD PDSCH Closed Loop Single Layer Spatial Multiplexing on antenna ports 7 or 8 with TM9 Interference Model - Enhanced Performance Requirement Type B  p. 4622
8.3.1.1.5FDD PDSCH Closed Loop Single-layer Spatial Multiplexing on antenna ports 7 or 8 with CRS Interference Model - Enhanced Performance Requirement Type B  p. 4628
8.3.1.1.6FDD PDSCH Closed Loop Single-layer Spatial Multiplexing on antenna ports 7 or 8 with TM3 interference model - Enhanced Performance Requirement Type B  p. 4631
8.3.1.1.7FDD PDSCH Closed Loop Single-layer Spatial Multiplexing on antenna ports 7 or 8 with TM10 serving cell configuration and TM9 interference model - Enhanced Performance Requirement Type B  p. 4635
8.3.1.1.7.1Test purpose  p. 4636
8.3.1.1.7.2Test applicability  p. 4636
8.3.1.1.7.3Minimum conformance requirements  p. 4636
8.3.1.1.7.4Test description  p. 4638
8.3.1.1.8-  p. 4642
8.3.1.1.9FDD PDSCH Single-layer Spatial Multiplexing for FD-MIMO  p. 4642
8.3.1.1.9.1Test purpose  p. 4642
8.3.1.1.9.2Test applicability  p. 4642
8.3.1.1.9.3Minimum conformance requirements  p. 4642
8.3.1.1.9.4Test description  p. 4644
8.3.1.1.9.5Test requirement  p. 4646
8.3.1.1.10FDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 without a simultaneous transmission for eFD-MIMO  p. 4647
8.3.1.1.10.1Test purpose  p. 4647
8.3.1.1.10.2Test applicability  p. 4647
8.3.1.1.10.3Minimum conformance requirements  p. 4647
8.3.1.1.10.4Test description  p. 4649
8.3.1.1.10_D.5Test requirement  p. 4650
8.3.1.2FDD PDSCH Dual-layer Spatial Multiplexing Performance (UE-Specific Reference Symbols)  p. 4650
8.3.1.2.1_DFDD PDSCH Dual-layer Spatial Multiplexing for eDL-MIMO  p. 4650
8.3.1.2.1_D.1Test purpose  p. 4650
8.3.1.2.1_D.2Test applicability  p. 4650
8.3.1.2.1_D.3Minimum conformance requirements  p. 4650
8.3.1.2.1_D.4Test description  p. 4651
8.3.1.2.1_D.4.2Test procedure  p. 4652
8.3.1.2.1_D.4.3Message contents  p. 4652
8.3.1.2.1_D.5Test requirement  p. 4653
8.3.1.2.1_D_1FDD PDSCH Dual-layer Spatial Multiplexing for eDL-MIMO (Release 11 and forward)  p. 4654
8.3.1.2.1_D_1.1Test purpose  p. 4654
8.3.1.2.1_D_1.2Test applicability  p. 4654
8.3.1.2.1_D_1.3Minimum conformance requirements  p. 4654
8.3.1.2.1_D_1.4Test description  p. 4655
8.3.1.2.1_D_1.4.2Test procedure  p. 4656
8.3.1.2.1_D_1.4.3Message contents  p. 4656
8.3.1.2.1_D_1.5Test requirement  p. 4657
8.3.1.2.2FDD PDSCH Dual-layer Spatial Multiplexing - Enhanced Performance Requirement Type C  p. 4659
8.3.1.2.2.1Test purpose  p. 4659
8.3.1.2.2.2Test applicability  p. 4659
8.3.1.2.2.3Minimum conformance requirements  p. 4659
8.3.1.2.2.4Test description  p. 4660
8.3.1.2.2.4.1Initial conditions  p. 4660
8.3.1.2.2.4.2Test procedure  p. 4661
8.3.1.2.2.4.3Message contents  p. 4661
8.3.1.2.2.5Test requirement  p. 4662
8.3.1.3FDD PDSCH Performance with DCI format 2D and non Quasi Co-located Antenna Ports  p. 4663
8.3.1.3.1_FFDD PDSCH Performance with DCI format 2D, non Quasi Co-located Antenna Ports, Same Cell ID and single NZP CSI-RS resource for CoMP  p. 4663
8.3.1.3.1_F.1Test purpose  p. 4663
8.3.1.3.1_F.2Test applicability  p. 4663
8.3.1.3.1_F.3Minimum conformance requirements  p. 4663
8.3.1.3.1_F.4Test description  p. 4665
8.3.1.3.1_F.4.1Initial conditions  p. 4665
8.3.1.3.1_F.4.2Test procedure  p. 4665
8.3.1.3.1_F.4.3Message contents  p. 4666
8.3.1.3.1_F.5Test requirement  p. 4667
8.3.1.3.2_FFDD PDSCH Performance with DCI format 2D, non Quasi Co-located Antenna Ports, Same Cell ID and multiple NZP CSI-RS resources for CoMP  p. 4668
8.3.1.3.2_F.1Test purpose  p. 4668
8.3.1.3.2_F.2Test applicability  p. 4668
8.3.1.3.2_F.3Minimum conformance requirements  p. 4668
8.3.1.3.2_F.4Test description  p. 4670
8.3.1.3.2_F.4.1Initial conditions  p. 4670
8.3.1.3.2_F.4.2Test procedure  p. 4670
8.3.1.3.2_F.4.3Message contents  p. 4671
8.3.1.3.2_F.5Test requirements  p. 4673
8.3.1.3.3_FFDD PDSCH Performance with DCI format 2D, non Quasi Co-located Antenna Ports, Different Cell ID, Colliding CRS and single NZP CSI-RS resource for CoMP  p. 4674
8.3.1.3.3_F.1Test purpose  p. 4674
8.3.1.3.3_F.2Test applicability  p. 4674
8.3.1.3.3_F.3Minimum conformance requirements  p. 4674
8.3.1.3.3_F.4Test description  p. 4676
8.3.1.3.3_F.4.1Initial conditions  p. 4676
8.3.1.3.3_F.4.2Test procedure  p. 4676
8.3.1.3.3_F.4.3Message contents  p. 4676
8.3.1.3.3_F.5Test requirements  p. 4678
8.3.2TDD  p. 4678
8.3.2.1TDD PDSCH Single-layer Spatial Multiplexing Performance (UE-Specific Reference Symbols)  p. 4679
8.3.2.1.1TDD PDSCH Single-layer Spatial Multiplexing on antenna port 5 (Release 8 and forward)  p. 4679
8.3.2.1.1_1TDD PDSCH Single-layer Spatial Multiplexing on antenna port 5 (Release 9 and forward)  p. 4682
8.3.2.1.2TDD PDSCH Single-layer Spatial Multiplexing on antenna port 7 or 8 without a simultaneous transmission  p. 4684
8.3.2.1.2_DTDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 without a simultaneous transmission for eDL-MIMO  p. 4686
8.3.2.1.2_HTDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 without a simultaneous transmission for eDL-MIMO for 256QAM in DL  p. 4691
8.3.2.1.3TDD PDSCH Single-layer Spatial Multiplexing on antenna port 7 or 8 with a simultaneous transmission  p. 4693
8.3.2.1.3_DTDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 with a simultaneous transmission for eDL-MIMO  p. 4695
8.3.2.1.4TDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 with TM9 Interference Model - Enhanced Performance Requirement Type A  p. 4700
8.3.2.1.4.1Test purpose  p. 4700
8.3.2.1.4.2Test applicability  p. 4700
8.3.2.1.4.3Minimum conformance requirements  p. 4700
8.3.2.1.4.4Test description  p. 4702
8.3.2.1.4.5Test requirement  p. 4705
8.3.2.1.5TDD PDSCH Closed Loop Single-layer Spatial Multiplexing on antenna ports 7 or 8 with TM9 Interference Model - Enhanced Performance Requirement Type B  p. 4707
8.3.2.1.6TDD PDSCH Closed Loop Single-layer Spatial Multiplexing on antenna ports 7 or 8 with CRS Interference Model - Enhanced Performance Requirement Type B  p. 4713
8.3.2.1.7TDD PDSCH Closed Loop Single-layer Spatial Multiplexing on antenna ports 7 or 8 with TM3 Interference Model - Enhanced Performance Requirement Type B  p. 4717
8.3.2.1.8TDD PDSCH Closed Loop Single-layer Spatial Multiplexing on antenna ports 7 or 8 with TM10 serving cell configuration and TM9 interference model - Enhanced Performance Requirement Type B  p. 4722
8.3.2.1.8.1Test purpose  p. 4722
8.3.2.1.8.2Test applicability  p. 4722
8.3.2.1.8.3Minimum conformance requirements  p. 4722
8.3.2.1.8.4Test description  p. 4724
8.3.2.1.9-  p. 4728
8.3.2.1.10TDD PDSCH Single-layer Spatial Multiplexing for FD-MIMO  p. 4728
8.3.2.1.10.1Test purpose  p. 4728
8.3.2.1.10.2Test applicability  p. 4728
8.3.2.1.10.3Minimum conformance requirements  p. 4728
8.3.2.1.10.4Test description  p. 4730
8.3.2.1.10.5Test requirement  p. 4732
8.3.2.1.11TDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 without a simultaneous transmission for eFD-MIMO  p. 4733
8.3.2.2TDD PDSCH Dual-layer Spatial Multiplexing Performance (UE-Specific Reference Symbols)  p. 4736
8.3.2.2.1TDD PDSCH Dual-layer Spatial Multiplexing  p. 4736
8.3.2.2.1_DTDD PDSCH Dual-layer Spatial Multiplexing for eDL-MIMO  p. 4739
8.3.2.2.1_D.1Test purpose  p. 4739
8.3.2.2.1_D.2Test applicability  p. 4739
8.3.2.2.1_D.3Minimum conformance requirements  p. 4739
8.3.2.2.1_D.4Test description  p. 4740
8.3.2.2.1_D.4.2Test procedure  p. 4741
8.3.2.2.1_D.4.3Message contents  p. 4741
8.3.2.2.1_D.5Test requirement  p. 4742
8.3.2.2.1_D_1TDD PDSCH Dual-layer Spatial Multiplexing for eDL-MIMO (Release 11 and forward)  p. 4743
8.3.2.2.1_D_1.1Test purpose  p. 4743
8.3.2.2.1_D_1.2Test applicability  p. 4743
8.3.2.2.1_D_1.3Minimum conformance requirements  p. 4743
8.3.2.2.1_D_1.4Test description  p. 4744
8.3.2.2.1_D_1.4.2Test procedure  p. 4745
8.3.2.2.1_D_1.4.3Message contents  p. 4745
8.3.2.2.1_D_1.5Test requirement  p. 4746
8.3.2.2.2TDD PDSCH Dual-layer Spatial Multiplexing - Enhanced Performance Requirement Type C  p. 4748
8.3.2.2.2.1Test purpose  p. 4748
8.3.2.2.2.2Test applicability  p. 4748
8.3.2.2.2.3Minimum conformance requirements  p. 4748
8.3.2.2.2.4Test description  p. 4749
8.3.2.2.2.4.1Initial conditions  p. 4749
8.3.2.2.2.4.2Test procedure  p. 4750
8.3.2.1.2.4.3Message contents  p. 4750
8.3.2.2.2.5Test requirement  p. 4750
8.3.2.3Dual-Layer Spatial Multiplexing (with multiple CSI-RS configurations)  p. 4751
8.3.2.4TDD PDSCH Performance with DCI format 2D and non Quasi Co-located Antenna Ports  p. 4751
8.3.2.4.1_FTDD PDSCH Performance with DCI format 2D, non Quasi Co-located Antenna Ports, Same Cell ID and single NZP CSI-RS resource for CoMP  p. 4751
8.3.2.4.1_F.1Test purpose  p. 4751
8.3.2.4.1_F.2Test applicability  p. 4751
8.3.2.4.1_F.3Minimum conformance requirements  p. 4751
8.3.2.4.1_F.4Test description  p. 4753
8.3.2.4.1_F.4.1Initial conditions  p. 4753
8.3.2.4.1_F.4.2Test procedure  p. 4753
8.3.2.4.1_F.4.3Message contents  p. 4754
8.3.2.4.1_F.5Test requirement  p. 4755
8.3.2.4.2_FTDD PDSCH Performance with DCI format 2D, non Quasi Co-located Antenna Ports, Same Cell ID and multiple NZP CSI-RS resources for CoMP  p. 4756
8.3.2.4.2_F.1Test purpose  p. 4756
8.3.2.4.2_F.2Test applicability  p. 4756
8.3.2.4.2_F.3Minimum conformance requirements  p. 4756
8.3.2.4.2_F.4Test description  p. 4758
8.3.2.4.2_F.4.1Initial conditions  p. 4758
8.3.2.4.2_F.4.2Test procedure  p. 4758
8.3.2.4.2_F.4.3Message contents  p. 4759
8.3.2.4.2_F.5Test requirements  p. 4761
8.3.2.4.3_FTDD PDSCH Performance with DCI format 2D, non Quasi Co-located Antenna Ports, Different Cell ID, Colliding CRS and single NZP CSI-RS resource for CoMP  p. 4762
8.3.2.4.3_F.1Test purpose  p. 4762
8.3.2.4.3_F.2Test applicability  p. 4762
8.3.2.4.3_F.3Minimum conformance requirements  p. 4762
8.3.2.4.3_F.4Test description  p. 4764
8.3.2.4.3_F.4.1Initial conditions  p. 4764
8.3.2.4.3_F.4.2Test procedure  p. 4764
8.3.2.4.3_F.4.3Message contents  p. 4764
8.3.2.4.3_F.5Test requirements  p. 4766
8.3.3LAA  p. 4767
8.3.3.1Dual-Layer Spatial Multiplexing with DM-RS  p. 4767
8.3.3.1.1LAA Dual-Layer Spatial Multiplexing with DM-RS with FDD as PCell  p. 4767
8.3.3.1.1.1Test purpose  p. 4767
8.3.3.1.1.2Test applicability  p. 4767
8.3.3.1.1.3Minimum conformance requirements  p. 4767
8.3.3.1.1.4Test description  p. 4770
8.3.3.1.1.4.1Initial conditions  p. 4770
8.3.3.1.1.4.2Test procedure  p. 4771
8.3.3.1.1.4.3Message contents  p. 4771
8.3.3.1.1.5Test Requirements  p. 4773
8.3.3.1.2LAA Dual-Layer Spatial Multiplexing with DM-RS with TDD as PCell  p. 4774
8.3.3.1.2.1Test purpose  p. 4774
8.3.3.1.2.2Test applicability  p. 4774
8.3.3.1.2.3Minimum conformance requirements  p. 4774
8.3.3.1.2.4Test description  p. 4777
8.3.3.1.2.4.1Initial conditions  p. 4777
8.3.3.1.2.4.2Test procedure  p. 4778
8.3.3.1.2.4.3Message contents  p. 4778
8.3.3.1.2.5Test Requirements  p. 4780
8.4Demodulation of PCFICH/PDCCH  p. 4781
8.4.1FDD  p. 4781
8.4.1.1FDD PCFICH/PDCCH Single-antenna Port Performance  p. 4781
8.4.1.1.1Test purpose  p. 4781
8.4.1.1.2Test applicability  p. 4781
8.4.1.1.3Minimum conformance requirements  p. 4781
8.4.1.1.4Test description  p. 4782
8.4.1.1.5Test requirement  p. 4783
8.4.1.2FDD PCFICH/PDCCH Transmit Diversity Performance  p. 4783
8.4.1.2.1FDD PCFICH/PDCCH Transmit Diversity 2x2  p. 4783
8.4.1.2.1_1FDD PCFICH/PDCCH Transmit Diversity 2x2 (Release 9 and forward)  p. 4785
8.4.1.2.2FDD PCFICH/PDCCH Transmit Diversity 4x2  p. 4788
8.4.1.2.2_1FDD PCFICH/PDCCH Transmit Diversity 4x2 (Release 9 and forward)  p. 4790
8.4.1.2.3-  p. 4793
8.4.1.2.3_CFDD PCFICH/PDCCH Transmit Diversity 2x2 for eICIC  p. 4793
8.4.1.2.3_C.1FDD PCFICH/PDCCH Transmit Diversity 2x2 for eICIC (non-MBSFN ABS)  p. 4793
8.4.1.2.3_C.2FDD PCFICH/PDCCH Transmit Diversity 2x2 for eICIC (MBSFN ABS)  p. 4798
8.4.1.2.3_D-  p. 4804
8.4.1.2.3_EFDD PCFICH/PDCCH Transmit Diversity 2x2 for feICIC  p. 4804
8.4.1.2.3_E.1FDD PCFICH/PDCCH Transmit Diversity 2x2 for feICIC (non-MBSFN ABS)  p. 4804
8.4.1.2.3_E.2FDD PCFICH/PDCCH Transmit Diversity 2x2 for feICIC (MBSFN ABS)  p. 4810
8.4.1.2.4-  p. 4816
8.4.1.2.5FDD Enhanced Downlink Control Channel Performance Requirement Type A for PCFICH/PDCCH, 2 Tx Antenna Port under Asynchronous Network  p. 4816
8.4.1.2.6FDD Enhanced Downlink Control Channel Performance Requirement Type A for PCFICH/PDCCH, 2 Tx Antenna Port with Non-Colliding CRS Dominant Interferer  p. 4820
8.4.1.2.7FDD Enhanced Downlink Control Channel Performance Requirement Type B for PCFICH/PDCCH, 2 Tx Antenna Port with Colliding CRS Dominant Interferer  p. 4824
8.4.1.2.8FDD Enhanced Downlink Control Channel Performance Requirement Type B for PCFICH/PDCCH, 2 Tx Antenna Port with Non-Colliding CRS Dominant Interferer  p. 4828
8.4.2TDD  p. 4832
8.4.2.1TDD PCFICH/PDCCH Single-antenna Port Performance  p. 4832
8.4.2.1.1Test purpose  p. 4832
8.4.2.1.2Test applicability  p. 4832
8.4.2.1.3Minimum conformance requirements  p. 4833
8.4.2.1.4Test description  p. 4833
8.4.2.1.5Test requirement  p. 4834
8.4.2.2TDD PCFICH/PDCCH Transmit Diversity Performance  p. 4835
8.4.2.2.1TDD PCFICH/PDCCH Transmit Diversity 2x2  p. 4835
8.4.2.2.1_1TDD PCFICH/PDCCH Transmit Diversity 2x2 (Release 9 and forward)  p. 4837
8.4.2.2.2TDD PCFICH/PDCCH Transmit Diversity 4x2  p. 4840
8.4.2.2.2_1TDD PCFICH/PDCCH Transmit Diversity 4x2 (Release 9 and forward)  p. 4842
8.4.2.2.3_CTDD PCFICH/PDCCH Transmit Diversity 2x2 for eICIC  p. 4845
8.4.2.2.3_C.1TDD PCFICH/PDCCH Transmit Diversity 2x2 for eICIC (non-MBSFN ABS)  p. 4845
8.4.2.2.3_C.2TDD PCFICH/PDCCH Transmit Diversity 2x2 for eICIC (MBSFN ABS)  p. 4852
8.4.2.2.3_D-  p. 4858
8.4.2.2.3_ETDD PCFICH/PDCCH Transmit Diversity 2x2 for feICIC  p. 4858
8.4.2.2.3_E.1TDD PCFICH/PDCCH Transmit Diversity 2x2 for feICIC (non-MBSFN ABS)  p. 4858
8.4.2.2.3_E.2TDD PCFICH/PDCCH Transmit Diversity 2x2 for feICIC (MBSFN ABS)  p. 4864
8.4.2.2.4-  p. 4871
8.4.2.2.5TDD Enhanced Downlink Control Channel Performance Requirement Type A for PCFICH/PDCCH, 2 Tx Antenna Port with Colliding CRS Dominant Interferer  p. 4871
8.4.2.2.6TDD Enhanced Downlink Control Channel Performance Requirement Type A for PCFICH/PDCCH, 2 Tx Antenna Port with Non-Colliding CRS Dominant Interferer  p. 4875
8.4.2.2.7TDD Enhanced Downlink Control Channel Performance Requirement Type B for PCFICH/PDCCH, 2 Tx Antenna Port with Colliding CRS Dominant Interferer  p. 4880
8.4.2.2.8TDD Enhanced Downlink Control Channel Performance Requirement Type B for PCFICH/PDCCH, 2 Tx Antenna Port with Non-Colliding CRS Dominant Interferer  p. 4884
8.4.3LAA  p. 4888
8.4.3.1Transmit Diversity Performance  p. 4888
8.4.3.1.1LAA PCFICH/PDCCH Transmit Diversity 2x2 with FDD as Pcell  p. 4888
8.4.3.1.2LAA PCFICH/PDCCH Transmit Diversity 2x2 with TDD as Pcell  p. 4892
8.5Demodulation of PHICH  p. 4896
8.5.1FDD  p. 4896
8.5.1.1FDD PHICH Single-antenna Port Performance  p. 4896
8.5.1.1.1Test purpose  p. 4896
8.5.1.1.2Test applicability  p. 4896
8.5.1.1.3Minimum conformance requirements  p. 4896
8.5.1.1.4Test description  p. 4897
8.5.1.1.5Test requirement  p. 4898
8.5.1.2FDD PHICH Transmit Diversity Performance  p. 4899
8.5.1.2.1FDD PHICH Transmit Diversity 2x2  p. 4899
8.5.1.2.1_1FDD PHICH Transmit Diversity 2x2 (Release 9 and forward)  p. 4902
8.5.1.2.2FDD PHICH Transmit Diversity 4x2  p. 4904
8.5.1.2.2_1FDD PHICH Transmit Diversity 4x2 (Release 9 and forward)  p. 4907
8.5.1.2.3-  p. 4909
8.5.1.2.3_A-  p. 4909
8.5.1.2.3_B-  p. 4909
8.5.1.2.3_CFDD PHICH Transmit Diversity 2x2 for eICIC  p. 4909
8.5.1.2.3_C.1FDD PHICH Transmit Diversity 2x2 for eICIC (non-MBSFN ABS)  p. 4909
8.5.1.2.3_D-  p. 4915
8.5.1.2.3_EFDD PHICH Transmit Diversity 2x2 for feICIC  p. 4915
8.5.1.2.3_E.1FDD PHICH Transmit Diversity 2x2 for feICIC (non-MBSFN ABS)  p. 4915
8.5.1.2.4-  p. 4922
8.5.1.2.5FDD Enhanced Downlink Control Channel Performance Requirement Type A for PHICH- 2 Tx Antenna Ports under Asynchronous Network  p. 4922
8.5.1.2.6FDD Enhanced Downlink Control Channel Performance Requirement Type A for PHICH - 2 Tx Antenna Ports with Non-Colliding CRS Dominant Interferer  p. 4926
8.5.1.2.7FDD Enhanced Downlink Control Channel Performance Requirement Type B for PHICH - 2 Tx Antenna Ports with Colliding CRS Dominant Interferer  p. 4930
8.5.1.2.8FDD Enhanced Downlink Control Channel Performance Requirement Type B for PHICH - 2 Tx Antenna Ports with Non-Colliding CRS Dominant Interferer  p. 4934
8.5.2TDD  p. 4938
8.5.2.1TDD PHICH Single-antenna Port Performance  p. 4938
8.5.2.1.1Test purpose  p. 4938
8.5.2.1.2Test applicability  p. 4938
8.5.2.1.3Minimum conformance requirements  p. 4938
8.5.2.1.4Test description  p. 4939
8.5.2.1.5Test requirement  p. 4941
8.5.2.2TDD PHICH Transmit Diversity Performance  p. 4941
8.5.2.2.1TDD PHICH Transmit Diversity 2x2  p. 4941
8.5.2.2.1_1TDD PHICH Transmit Diversity 2x2 (Release 9 and forward)  p. 4944
8.5.2.2.2TDD PHICH Transmit Diversity 4x2  p. 4947
8.5.2.2.2_1TDD PHICH Transmit Diversity 4x2 (Release 9 and forward)  p. 4950
8.5.2.2.3-  p. 4953
8.5.2.2.3_A-  p. 4953
8.5.2.2.3_B-  p. 4953
8.5.2.2.3_CTDD PHICH Transmit Diversity 2x2 for eICIC  p. 4953
8.5.2.2.3_C.1TDD PHICH Transmit Diversity 2x2 for eICIC (non-MBSFN ABS)  p. 4953
8.5.2.2.3_D-  p. 4959
8.5.2.2.3_ETDD PHICH Transmit Diversity 2x2 for feICIC  p. 4959
8.5.2.2.3_E.1TDD PHICH Transmit Diversity 2x2 for feICIC (non-MBSFN ABS)  p. 4959
8.5.2.2.4-  p. 4966
8.5.2.2.5TDD Enhanced Downlink Control Channel Performance Requirement Type A for PHICH- 2 Tx Antenna Ports with Colliding CRS Dominant Interferer  p. 4966
8.5.2.2.6TDD Enhanced Downlink Control Channel Performance Requirement Type A for PHICH - 2 Tx Antenna Ports with Non-Colliding CRS Dominant Interferer  p. 4969
8.5.2.2.7TDD Enhanced Downlink Control Channel Performance Requirement Type B for PHICH- 2 Tx Antenna Ports with Colliding CRS Dominant Interferer  p. 4973
8.5.2.2.8TDD Enhanced Downlink Control Channel Performance Requirement Type B for PHICH- 2 Tx Antenna Ports with Non-Colliding CRS Dominant Interferer  p. 4977
8.6Demodulation of PBCH  p. 4981
8.7Sustained downlink data rate provided by lower layers  p. 4981
8.7.1FDD  p. 4981
8.7.1.1FDD sustained data rate performance  p. 4982
8.7.1.1.1Test purpose  p. 4982
8.7.1.1.2Test applicability  p. 4983
8.7.1.1.3Minimum requirements  p. 4983
8.7.1.1.4Test description  p. 4984
8.7.1.1.5Test requirement  p. 4986
8.7.1.1_1FDD sustained data rate performance (Rel 10 and forward)  p. 4987
8.7.1.1_1.1Test purpose  p. 4987
8.7.1.1_1.2Test applicability  p. 4987
8.7.1.1_1.3Minimum requirements  p. 4987
8.7.1.1_1.4Test description  p. 4988
8.7.1.1_1.5Test requirement  p. 4988
8.7.1.1_2FDD sustained data rate performance for UE category 1bis  p. 4989
8.7.1.1_AFDD sustained data rate performance for CA  p. 4991
8.7.1.1_A.1FDD Sustained data rate performance for CA (2DL CA)  p. 4991
8.7.1.1_A.2FDD Sustained data rate performance for CA (3DL CA)  p. 4998
8.7.1.1_A.3Void  p. …
8.7.1.1_A.4FDD Sustained data rate performance for CA (4DL CA)  p. 5006
8.7.1.1_A.5FDD Sustained data rate performance for CA (5DL CA)  p. 5013
8.7.1.1_A.6FDD Sustained data rate performance for CA (6DL CA)  p. 5020
8.7.1.1_A.6.4-  p. 5021
8.7.1.1_A.6.4.1Initial conditions  p. 5021
8.7.1.1_A.6.4.2Test procedure  p. 5022
8.7.1.1_A.6.4.3Message contents  p. 5022
8.7.1.1_A.6.5Test Requirements  p. 5024
8.7.1.1_A.7FDD Sustained data rate performance for CA (7DL CA)  p. 5024
8.7.1.1_HFDD sustained data rate performance for 256QAM in DL  p. 5029
8.7.1.1_H.1FDD sustained data rate performance for 256QAM in DL (Single Carrier)  p. 5029
8.7.1.1_H.1.1Test purpose  p. 5029
8.7.1.1_H.1.2Test applicability  p. 5029
8.7.1.1_H.1.3Minimum requirements  p. 5029
8.7.1.1_H.1.4Test description  p. 5030
8.7.1.1_H.1.5Test requirement  p. 5031
8.7.1.1_H.2FDD Sustained data rate performance for CA (2DL CA) for 256QAM in DL  p. 5032
8.7.1.1_H.3FDD Sustained data rate performance for CA for 256QAM in DL (3DL CA)  p. 5035
8.7.1.1_H.4FDD Sustained data rate performance for CA (4DL CA) for 256QAM in DL  p. 5041
8.7.1.1_H.5FDD Sustained data rate performance for CA (5DL CA) for 256QAM in DL  p. 5047
8.7.1.1_H.7FDD Sustained data rate performance for CA (7DL CA) for 256QAM in DL  p. 5053
8.7.2TDD  p. 5056
8.7.2.1TDD sustained data rate performance  p. 5057
8.7.2.1.1Test purpose  p. 5057
8.7.2.1.2Test applicability  p. 5057
8.7.2.1.3Minimum requirements  p. 5057
8.7.2.1.4Test description  p. 5059
8.7.2.1.5Test requirement  p. 5061
8.7.2.1_1TDD sustained data rate performance (Rel 10 and forward)  p. 5062
8.7.2.1_1.1Test purpose  p. 5062
8.7.2.1_1.2Test applicability  p. 5062
8.7.2.1_1.3Minimum requirements  p. 5062
8.7.2.1_1.4Test description  p. 5062
8.7.2.1_1.5Test requirement  p. 5063
8.7.2.1_2TDD sustained data rate performance for UE category 1bis  p. 5064
8.7.2.1_ATDD sustained data rate performance for CA  p. 5066
8.7.2.1_A.1TDD sustained data rate performance for CA (2DL CA)  p. 5066
8.7.2.1_A.2TDD Sustained data rate performance for CA (3DL CA)  p. 5071
8.7.2.1_A.3TDD Sustained data rate performance for CA (4DL CA)  p. 5077
8.7.2.1_A.4Void  p. …
8.7.2.1_A.5TDD Sustained data rate performance for CA (5DL CA)  p. 5083
8.7.2.1_A.5.1Test purpose  p. 5083
8.7.2.1_A.5.2Test applicability  p. 5083
8.7.2.1_A.5.3Minimum conformance requirements  p. 5083
8.7.2.1_A.5.4Test description  p. 5084
8.7.2.1_A.5.4.1Initial conditions  p. 5084
8.7.2.1_A.5.4.2Test procedure  p. 5085
8.7.2.1_A.5.4.3Message contents  p. 5086
8.7.2.1_A.5.5Test requirement  p. 5087
8.7.2.1_A.6TDD Sustained data rate performance for CA (6DL CA)  p. 5088
8.7.2.1_A.6.1Test purpose  p. 5088
8.7.2.1_A.6.2Test applicability  p. 5088
8.7.2.1_A.6.3Minimum conformance requirements  p. 5088
8.7.2.1_A.6.4Test description  p. 5089
8.7.2.1_A.6.4.1Initial conditions  p. 5089
8.7.2.1_A.6.4.2Test procedure  p. 5090
8.7.2.1_A.6.4.3Message contents  p. 5090
8.7.2.1_A.6.5Test requirement  p. 5092
8.7.2.1_A.7TDD Sustained data rate performance for CA (7DL CA)  p. 5093
8.7.2.1_A.7.1Test purpose  p. 5093
8.7.2.1_A.7.2Test applicability  p. 5093
8.7.2.1_A.7.3Minimum conformance requirements  p. 5093
8.7.2.1_A.7.4Test description  p. 5094
8.7.2.1_A.7.4.1Initial conditions  p. 5094
8.7.2.1_A.7.4.2Test procedure  p. 5095
8.7.2.1_A.7.4.3Message contents  p. 5095
8.7.2.1_A.7.5Test requirement  p. 5097
8.7.2.1_HTDD sustained data rate performance for 256QAM in DL  p. 5098
8.7.2.1_H.1TDD sustained data rate performance for 256QAM in DL (Single Carrier)  p. 5098
8.7.2.1_H.2TDD sustained data rate performance for CA (2DL CA) for 256QAM in DL  p. 5101
8.7.2.1_H.3TDD Sustained data rate performance for CA (3DL CA) for 256QAM in DL  p. 5103
8.7.2.1_H.4TDD Sustained data rate performance for CA (4DL CA) for 256QAM in DL  p. 5106
8.7.2.1_H.5TDD Sustained data rate performance for CA (5DL CA) for 256QAM in DL  p. 5109
8.7.2.1_H.6TDD Sustained data rate performance for CA (6DL CA) for 256QAM in DL  p. 5112
8.7.2.1_H.7TDD Sustained data rate performance for CA (7DL CA) for 256QAM in DL  p. 5115
8.7.3FDD (EPDCCH scheduling)  p. 5117
8.7.3.1FDD sustained data rate performance for EPDCCH scheduling  p. 5118
8.7.4TDD (EPDCCH scheduling)  p. 5124
8.7.4.1TDD sustained data rate performance for EPDCCH scheduling  p. 5125
8.7.5TDD FDD CA Sustained data rate performance  p. 5130
8.7.5.1TDD FDD CA Sustained data rate performance for FDD PCell  p. 5132
8.7.5.1.1TDD FDD CA Sustained data rate performance for FDD PCell (2DL CA)  p. 5132
8.7.5.1.1.1Test purpose  p. 5132
8.7.5.1.1.2Test applicability  p. 5132
8.7.5.1.1.3Minimum requirements  p. 5132
8.7.5.1.1.4Test description  p. 5133
8.7.5.1.1.5Test requirement  p. 5136
8.7.5.1.2TDD FDD CA Sustained data rate performance for FDD PCell (3DL CA)  p. 5137
8.7.5.1.2.1Test purpose  p. 5137
8.7.5.1.2.2Test applicability  p. 5137
8.7.5.1.2.3Minimum requirements  p. 5137
8.7.5.1.2.4Test description  p. 5138
8.7.5.1.2.5Test requirement  p. 5143
8.7.5.1.3TDD FDD CA Sustained data rate performance for FDD PCell (4DL CA)  p. 5144
8.7.5.1.3.1Test purpose  p. 5144
8.7.5.1.3.2Test applicability  p. 5144
8.7.5.1.3.3Minimum requirements  p. 5144
8.7.5.1.3.4Test description  p. 5146
8.7.5.1.3.5Test requirement  p. 5151
8.7.5.1.4TDD FDD CA Sustained data rate performance for FDD PCell (5DL CA)  p. 5153
8.7.5.1.5TDD FDD CA Sustained data rate performance for FDD PCell (6DL CA)  p. 5158
8.7.5.1.6TDD FDD CA Sustained data rate performance for FDD PCell (7DL CA)  p. 5163
8.7.5.1_HTDD FDD CA Sustained data rate performance for FDD PCell for 256QAM in DL  p. 5168
8.7.5.1_H.1TDD FDD CA Sustained data rate performance for FDD PCell (2DL CA) for 256QAM in DL  p. 5168
8.7.5.1_H.1.1Test purpose  p. 5168
8.7.5.1_H.1.2Test applicability  p. 5168
8.7.5.1_H.1.3Minimum requirements  p. 5168
8.7.5.1_H.1.4Test description  p. 5168
8.7.5.1_H.1.5Test requirement  p. 5169
8.7.5.1_H.2TDD FDD CA Sustained data rate performance for FDD PCell (3DL CA) for 256QAM in DL  p. 5170
8.7.5.1_H.2.1Test purpose  p. 5170
8.7.5.1_H.2.2Test applicability  p. 5170
8.7.5.1_H.2.3Minimum requirements  p. 5170
8.7.5.1_H.2.4Test description  p. 5171
8.7.5.1_H.2.5Test requirement  p. 5173
8.7.5.1_H.3TDD FDD CA Sustained data rate performance for FDD PCell (4DL CA) for 256QAM in DL  p. 5174
8.7.5.1_H.3.1Test purpose  p. 5174
8.7.5.1_H.3.2Test applicability  p. 5174
8.7.5.1_H.3.3Minimum requirements  p. 5174
8.7.5.1_H.3.4Test description  p. 5175
8.7.5.1_H.3.5Test requirement  p. 5178
8.7.5.1_H.4TDD FDD CA Sustained data rate performance for FDD PCell (5DL CA) for 256QAM in DL  p. 5179
8.7.5.1_H.4.1Test purpose  p. 5179
8.7.5.1_H.4.2Test applicability  p. 5179
8.7.5.1_H.4.3Minimum requirements  p. 5179
8.7.5.1_H.4.4Test description  p. 5180
8.7.5.1_H.4.5Test requirement  p. 5181
8.7.5.1_H.5TDD FDD CA Sustained data rate performance for FDD PCell (6DL CA) for 256QAM in DL  p. 5182
8.7.5.1_H.5.1Test purpose  p. 5182
8.7.5.1_H.5.2Test applicability  p. 5182
8.7.5.1_H.5.3Minimum conformance requirements  p. 5182
8.7.5.1_H.5.4Test description  p. 5183
8.7.5.1_H.5.5Test Requirements  p. 5184
8.7.5.2TDD FDD CA Sustained data rate performance for TDD PCell  p. 5185
8.7.5.2.1TDD FDD CA Sustained data rate performance for TDD PCell (2DL CA)  p. 5185
8.7.5.2.1.1Test purpose  p. 5185
8.7.5.2.1.2Test applicability  p. 5185
8.7.5.2.1.3Minimum requirements  p. 5185
8.7.5.2.1.4Test description  p. 5186
8.7.5.2.1.5Test requirement  p. 5189
8.7.5.2.2TDD FDD CA Sustained data rate performance for TDD PCell (3DL CA)  p. 5190
8.7.5.2.2.1Test purpose  p. 5190
8.7.5.2.2.2Test applicability  p. 5190
8.7.5.2.2.3Minimum requirements  p. 5190
8.7.5.2.2.4Test description  p. 5192
8.7.5.2.2.5Test requirement  p. 5196
8.7.5.2.3TDD FDD CA Sustained data rate performance for TDD PCell (4DL CA)  p. 5197
8.7.5.2.3.1Test purpose  p. 5197
8.7.5.2.3.2Test applicability  p. 5197
8.7.5.2.3.3Minimum requirements  p. 5197
8.7.5.2.3.4Test description  p. 5200
8.7.5.2.3.5Test requirement  p. 5205
8.7.5.2.4-  p. 5207
8.7.5.2.5TDD FDD CA Sustained data rate performance for TDD PCell (6DL CA)  p. 5207
8.7.5.2.5.1Test purpose  p. 5207
8.7.5.2.5.2Test applicability  p. 5207
8.7.5.2.5.3Minimum conformance requirements  p. 5207
8.7.5.2.5.4.1Initial conditions  p. 5208
8.7.5.2.5.4.2Test procedure  p. 5209
8.7.5.2.5.4.3Message contents  p. 5209
8.7.5.2.6TDD FDD CA Sustained data rate performance for TDD PCell (7DL CA)  p. 5211
8.7.5.2_H.4TDD FDD CA Sustained data rate performance for TDD PCell (5DL CA) for 256QAM in DL  p. 5216
8.7.5.2_H.4.1Test purpose  p. 5216
8.7.5.2_H.4.2Test applicability  p. 5216
8.7.5.2_H.4.3Minimum conformance requirements  p. 5217
8.7.5.2_H.4.4Test description  p. 5217
8.7.5.2_H.4.5Test requirement  p. 5218
8.7.5.2_H.5TDD FDD CA Sustained data rate performance for TDD PCell (6DL CA) for 256QAM in DL  p. 5219
8.7.5.2_H.5.1Test purpose  p. 5219
8.7.5.2_H.5.2Test applicability  p. 5219
8.7.5.2_H.5.3Minimum conformance requirements  p. 5219
8.7.5.2_H.5.4Test description  p. 5220
8.7.5.2_H.5.5Test Requirements  p. 5221
8.7.5.2_HTDD FDD CA Sustained data rate performance for TDD PCell for 256QAM in DL  p. 5222
8.7.5.2_H.1TDD FDD CA Sustained data rate performance for TDD PCell (2DL CA) for 256QAM in DL  p. 5222
8.7.5.2_H.1.1Test purpose  p. 5222
8.7.5.2_H.1.2Test applicability  p. 5222
8.7.5.2_H.1.3Minimum requirements  p. 5222
8.7.5.2_H.1.4Test description  p. 5223
8.7.5.2_H.1.5Test requirement  p. 5224
8.7.5.2_H.2TDD FDD CA Sustained data rate performance for TDD PCell (3DL CA) for 256QAM in DL  p. 5225
8.7.5.2_H.2.1Test purpose  p. 5225
8.7.5.2_H.2.2Test applicability  p. 5225
8.7.5.2_H.2.3Minimum requirements  p. 5225
8.7.5.2_H.2.4Test description  p. 5226
8.7.5.2_H.2.5Test requirement  p. 5228
8.7.5.2_H.3TDD FDD CA Sustained data rate performance for TDD PCell (4DL CA) for 256QAM in DL  p. 5229
8.7.5.2_H.3.1Test purpose  p. 5229
8.7.5.2_H.3.2Test applicability  p. 5229
8.7.5.2_H.3.3Minimum requirements  p. 5230
8.7.5.2_H.3.4Test description  p. 5231
8.7.5.2_H.3.5Test requirement  p. 5235
8.7.5.2.4aTDD FDD CA Sustained data rate performance for TDD PCell (5DL CA)  p. 5236
8.7.5.2.4.1Test purpose  p. 5236
8.7.5.2.4.2Test applicability  p. 5236
8.7.5.2.4.3Minimum requirements  p. 5236
8.7.5.2.4.4Test description  p. 5238
8.7.5.2.4.5Test requirement  p. 5241
8.7.6FDD (Dual Connectivity)  p. 5242
8.7.6.1FDD sustained data rate performance for Dual Connectivity 64QAM  p. 5243
8.7.6.1.1Test purpose  p. 5243
8.7.6.1.2Test applicability  p. 5243
8.7.6.1.3Minimum conformance requirements  p. 5243
8.7.6.1.4Test description  p. 5245
8.7.6.1.4.1Initial conditions  p. 5245
8.7.6.1.4.2Test procedure  p. 5246
8.7.6.1.4.3Message contents  p. 5246
8.7.6.1.5Test requirement  p. 5248
8.7.6.2FDD sustained data rate performance for Dual Connectivity 256QAM  p. 5249
8.7.6.2.1Test purpose  p. 5249
8.7.6.2.2Test applicability  p. 5249
8.7.6.2.3Minimum conformance requirements  p. 5249
8.7.6.2.4Test description  p. 5251
8.7.6.2.5Test requirement  p. 5253
8.7.7TDD (Dual Connectivity)  p. 5254
8.7.7.1TDD sustained data rate performance for Dual Connectivity 64QAM  p. 5255
8.7.7.1.1Test purpose  p. 5255
8.7.7.1.2Test applicability  p. 5255
8.7.7.1.3Minimum conformance requirements  p. 5255
8.7.7.1.4Test description  p. 5257
8.7.7.1.4.1Initial conditions  p. 5257
8.7.7.1.4.2Test procedure  p. 5257
8.7.7.1.4.3Message contents  p. 5258
8.7.7.1.5Test requirement  p. 5259
8.7.7.2TDD sustained data rate performance for Dual Connectivity 256QAM  p. 5260
8.7.7.2.1Test purpose  p. 5260
8.7.7.2.2Test applicability  p. 5260
8.7.7.2.3Minimum conformance requirements  p. 5260
8.7.7.2.4Test description  p. 5262
8.7.7.2.5Test requirement  p. 5264
8.7.8-  p. 5265
8.7.9FDD sustained data rate performance (4 layer MIMO)  p. 5265
8.7.9.1Minimum conformance requirements  p. 5265
8.7.9.2FDD sustained data rate performance for 4 layer MIMO (single carrier)  p. 5267
8.7.9.2.1Test purpose  p. 5267
8.7.9.2.2Test applicability  p. 5267
8.7.9.2.3Minimum conformance requirements  p. 5267
8.7.9.2.4Test description  p. 5267
8.7.9.2.5Test requirement  p. 5271
8.7.9.3FDD sustained data rate performance for 4 layer MIMO (2DL CA)  p. 5271
8.7.9.3.1Test purpose  p. 5271
8.7.9.3.2Test applicability  p. 5272
8.7.9.3.3Minimum conformance requirements  p. 5272
8.7.9.3.4Test description  p. 5272
8.7.9.3.5Test requirement  p. 5276
8.7.9.4FDD sustained data rate performance for 4 layer MIMO (3DL CA)  p. 5276
8.7.9.4.1Test purpose  p. 5277
8.7.9.4.2Test applicability  p. 5277
8.7.9.4.3Minimum conformance requirements  p. 5277
8.7.9.4.4Test description  p. 5277
8.7.9.4.5Test requirement  p. 5283
8.7.9.5FDD sustained data rate performance for 4 layer MIMO (4DL CA)  p. 5283
8.7.9.5.1Test purpose  p. 5284
8.7.9.5.2Test applicability  p. 5284
8.7.9.5.3Minimum conformance requirements  p. 5284
8.7.9.5.4Test description  p. 5284
8.7.9.5.5Test requirement  p. 5292
8.7.9.6FDD sustained data rate performance for 4 layer MIMO (5DL CA)  p. 5292
8.7.9.6.1Test purpose  p. 5293
8.7.9.6.2Test applicability  p. 5293
8.7.9.6.3Minimum conformance requirements  p. 5293
8.7.9.6.4Test description  p. 5293
8.7.9.6.5Test requirement  p. 5299
8.7.10TDD sustained data rate performance (4 layer MIMO)  p. 5299
8.7.10.1Minimum conformance requirements  p. 5299
8.7.10.2TDD sustained data rate performance for 4 layer MIMO (single carrier)  p. 5301
8.7.10.2.1Test purpose  p. 5301
8.7.10.2.2Test applicability  p. 5301
8.7.10.2.3Minimum conformance requirements  p. 5301
8.7.10.2.4Test description  p. 5301
8.7.10.2.5Test requirement  p. 5305
8.7.10.3TDD sustained data rate performance for 4 layer MIMO (2DL CA)  p. 5305
8.7.10.3.1Test purpose  p. 5305
8.7.10.3.2Test applicability  p. 5305
8.7.10.3.3Minimum conformance requirements  p. 5306
8.7.10.3.4Test description  p. 5306
8.7.10.3.5Test requirement  p. 5310
8.7.10.4TDD sustained data rate performance for 4 layer MIMO (3DL CA)  p. 5310
8.7.10.4.1Test purpose  p. 5310
8.7.10.4.2Test applicability  p. 5310
8.7.10.4.3Minimum conformance requirements  p. 5310
8.7.10.4.4Test description  p. 5311
8.7.10.4.5Test requirement  p. 5315
8.7.10.5TDD sustained data rate performance for 4 layer MIMO (4DL CA)  p. 5315
8.7.10.5.1Test purpose  p. 5315
8.7.10.5.2Test applicability  p. 5315
8.7.10.5.3Minimum conformance requirements  p. 5315
8.7.10.5.4Test description  p. 5315
8.7.10.5.5Test requirement  p. 5320
8.7.10.6TDD sustained data rate performance for 4 layer MIMO (5DL CA)  p. 5320
8.7.10.6.1Test purpose  p. 5320
8.7.10.6.2Test applicability  p. 5320
8.7.10.6.3Minimum conformance requirements  p. 5320
8.7.10.6.4Test description  p. 5320
8.7.10.6.5Test requirement  p. 5325
8.7.11TDD FDD CA Sustained data rate performance (4 layer MIMO)  p. 5325
8.7.11.1Minimum conformance requirements  p. 5325
8.7.11.2TDD FDD CA sustained data rate performance for 4 layer MIMO (2DL CA)  p. 5327
8.7.11.2.1Test purpose  p. 5327
8.7.11.2.2Test applicability  p. 5327
8.7.11.2.3Minimum conformance requirements  p. 5328
8.7.11.2.4Test description  p. 5328
8.7.11.2.5Test requirement  p. 5332
8.7.11.3TDD FDD CA sustained data rate performance for 4 layer MIMO (3DL CA)  p. 5332
8.7.11.3.1Test purpose  p. 5332
8.7.11.3.2Test applicability  p. 5332
8.7.11.3.3Minimum conformance requirements  p. 5332
8.7.11.3.4Test description  p. 5332
8.7.11.3.5Test requirement  p. 5342
8.7.11.4TDD FDD CA sustained data rate performance for 4 layer MIMO (4DL CA)  p. 5342
8.7.11.4.1Test purpose  p. 5342
8.7.11.4.2Test applicability  p. 5342
8.7.11.4.3Minimum conformance requirements  p. 5342
8.7.11.4.4Test description  p. 5342
8.7.11.4.5Test requirement  p. 5355
8.7.11.5TDD FDD CA sustained data rate performance for 4 layer MIMO (5DL CA)  p. 5355
8.7.11.5.1Test purpose  p. 5355
8.7.11.5.2Test applicability  p. 5355
8.7.11.5.3Minimum conformance requirements  p. 5355
8.7.11.5.4Test description  p. 5355
8.7.11.5.5Test requirement  p. 5367
8.7.12LAA Sustained data rate performance  p. 5368
8.7.12.1FDD CA in unlicensed bands  p. 5368
8.7.12.1.1Minimum conformance requirements (FDD CA in unlicensed bands)  p. 5368
8.7.12.1.2LAA sustained data rate performance with FDD as Pcell with 2DL CA  p. 5369
8.7.12.1.2.1LAA sustained data rate performance with FDD PCell with 2DL CA (2Rx)  p. 5369
8.7.12.1.2.1.1Test purpose  p. 5369
8.7.12.1.2.1.2Test applicability  p. 5369
8.7.12.1.2.1.3Minimum requirements  p. 5370
8.7.12.1.2.1.4Test description  p. 5370
8.7.12.1.2.1.5Test requirement  p. 5373
8.7.12.1.2.2LAA sustained data rate performance with FDD PCell for 4 layer MIMO (2DL CA)  p. 5373
8.7.12.1.2.2.1Test purpose  p. 5373
8.7.12.1.2.2.2Test applicability  p. 5373
8.7.12.1.2.2.3Minimum requirements  p. 5373
8.7.12.1.2.2.4Test description  p. 5374
8.7.12.1.2.2.5Test requirement  p. 5378
8.7.12.2TDD CA in unlicensed bands  p. 5379
8.7.12.2.1Minimum conformance requirements (TDD CA in unlicensed bands)  p. 5379
8.7.12.2.2LAA sustained data rate performance with TDD as Pcell with 2DL CA  p. 5380
8.7.12.2.2.1LAA sustained data rate performance with TDD PCell with 2DL CA (2Rx)  p. 5380
8.7.12.2.2.1.1Test purpose  p. 5380
8.7.12.2.2.1.2Test applicability  p. 5380
8.7.12.2.2.1.3Minimum requirements  p. 5381
8.7.12.2.2.1.4Test description  p. 5381
8.7.12.2.2.1.4.1Initial conditions  p. 5381
8.7.12.2.2.1.5Test requirement  p. 5384
8.7.12.2.2.2LAA sustained data rate performance with TDD PCell for 4 layer MIMO (2DL CA)  p. 5384
8.7.12.2.2.2.1Test purpose  p. 5384
8.7.12.2.2.2.2Test applicability  p. 5384
8.7.12.2.2.2.3Minimum requirements  p. 5384
8.7.12.2.2.2.4Test description  p. 5385
8.7.12.2.2.2.5Test requirement  p. 5389
8.8Demodulation of EPDCCH  p. 5390
8.8.1Distributed Transmission  p. 5390
8.8.1.1FDD distributed EPDCCH performance  p. 5390
8.8.1.1.1Test purpose  p. 5390
8.8.1.1.2Test applicability  p. 5390
8.8.1.1.3Minimum conformance requirements  p. 5390
8.8.1.1.4Test description  p. 5391
8.8.1.1.5Test requirement  p. 5392
8.8.1.2TDD distributed EPDCCH performance  p. 5392
8.8.1.2.1Test purpose  p. 5392
8.8.1.2.2Test applicability  p. 5392
8.8.1.2.3Minimum conformance requirements  p. 5392
8.8.1.2.4Test description  p. 5393
8.8.1.2.5Test requirement  p. 5394
8.8.2Localized Transmission with TM9  p. 5395
8.8.2.1FDD localized EPDCCH performance with TM9  p. 5395
8.8.2.1.1Test purpose  p. 5395
8.8.2.1.2Test applicability  p. 5395
8.8.2.1.3Minimum conformance requirements  p. 5395
8.8.2.1.4Test description  p. 5397
8.8.2.1.5Test requirement  p. 5398
8.8.2.2TDD localized EPDCCH performance with TM9  p. 5398
8.8.2.2.1Test purpose  p. 5398
8.8.2.2.2Test applicability  p. 5398
8.8.2.2.3Minimum conformance requirements  p. 5398
8.8.2.2.4Test description  p. 5400
8.8.2.2.5Test requirement  p. 5401
8.8.3Localized transmission with TM10 Type B quasi co-location type  p. 5401
8.8.3.1FDD localized EPDCCH transmission with TM10 Type B quasi co-location type  p. 5401
8.8.3.1.1Test purpose  p. 5401
8.8.3.1.2Test applicability  p. 5401
8.8.3.1.3Minimum conformance requirements  p. 5401
8.8.3.1.4Test description  p. 5403
8.8.3.1.5Test requirement  p. 5406
8.8.3.2TDD localized EPDCCH transmission with TM10 Type B quasi co-location type  p. 5406
8.8.3.2.1Test purpose  p. 5406
8.8.3.2.2Test applicability  p. 5406
8.8.3.2.3Minimum conformance requirements  p. 5406
8.8.3.2.4Test description  p. 5408
8.8.3.2.5Test requirement  p. 5411
8.8.4-  p. 5411
8.8.4.1FDD Enhanced Downlink Control Channel Performance Requirement Type A for EDPCCH - Localized Transmission with CRS Interference Model  p. 5411
8.8.4.2TDD Enhanced Downlink Control Channel Performance Requirement Type A for EDPCCH - Localized Transmission with CRS Interference Model  p. 5415
8.8.5-  p. 5421
8.8.5.1TDD Enhanced Downlink Control Channel Performance Requirement Type A for EDPCCH - Distributed Transmission with TM9 Interference Model  p. 5421
8.8.6-  p. 5425
8.8.6.1FDD Enhanced Downlink Control Channel Performance Requirement Type A for EDPCCH- Distributed Transmission with TM3 Interference Model  p. 5425
8.9Demodulation (Single receiver antenna)  p. 5428
8.9.1PDSCH  p. 5428
8.9.1.1FDD and half-duplex FDD (Fixed Reference Channel)  p. 5428
8.9.1.1.1FDD PDSCH Transmit Diversity 2x1 for UE category 0  p. 5429
8.9.1.1.1_1FDD PDSCH Transmit Diversity 2x1 for UE category 1bis  p. 5431
8.9.1.1.2FDD closed-loop spatial multiplexing performance (Cell-Specific Reference Symbols)  p. 5433
8.9.1.1.2_1FDD PDSCH Closed Loop Single Layer Spatial Multiplexing 4x1 for UE Category 1bis  p. 5435
8.9.1.1.3FDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 for UE category 0  p. 5438
8.9.1.1.3_1FDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 for UE category 1bis  p. 5441
8.9.1.2TDD (Fixed Reference Channel)  p. 5443
8.9.1.2.1TDD PDSCH Transmit Diversity for UE category 0  p. 5443
8.9.1.2.1_1TDD PDSCH Transmit Diversity for UE category 1bis  p. 5445
8.9.1.2.2TDD closed-loop spatial multiplexing performance (Cell-Specific Reference Symbols)  p. 5447
8.9.1.2.2_1TDD PDSCH Closed Loop Single Layer Spatial Multiplexing 4x1 for UE Category 1bis  p. 5450
8.9.1.2.3TDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 for UE category 0)  p. 5453
8.9.1.2.3_1TDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 for UE category 1bis  p. 5454
8.9.2PHICH  p. 5458
8.9.2.1FDD and half-duplex FDD  p. 5458
8.9.2.1.1FDD PHICH Transmit Diversity for UE category 0  p. 5458
8.9.2.1.1.1Test purpose  p. 5458
8.9.2.1.1.2Test applicability  p. 5458
8.9.2.1.1.3Minimum conformance requirements  p. 5458
8.9.2.1.1.4Test description  p. 5459
8.9.2.1.1.4.1Initial conditions  p. 5459
8.9.2.1.1.4.2Test procedure  p. 5459
8.9.2.1.1.4.3Message contents  p. 5459
8.9.2.1.1.5Test requirement  p. 5460
8.9.2.1.1_1FDD PHICH Transmit Diversity for UE category 1bis  p. 5460
8.9.2.1.1_1.1Test purpose  p. 5460
8.9.2.1.1_1.2Test applicability  p. 5460
8.9.2.1.1_1.3Minimum conformance requirements  p. 5460
8.9.2.1.1_1.4Test description  p. 5460
8.9.2.1.1_1.4.1Initial conditions  p. 5460
8.9.2.1.1_1.4.2Test procedure  p. 5460
8.9.2.1.1_1.4.3Message contents  p. 5460
8.9.2.1.1_1.5Test requirement  p. 5461
8.9.2.2.1TDD PHICH Transmit Diversity for UE category 0  p. 5461
8.9.2.2.1.1Test purpose  p. 5461
8.9.2.2.1.2Test applicability  p. 5461
8.9.2.2.1.3Minimum conformance requirements  p. 5461
8.9.2.2.1.4Test description  p. 5462
8.9.2.2.1.4.1Initial conditions  p. 5462
8.9.2.2.1.4.2Test procedure  p. 5463
8.9.2.2.1.4.3Message contents  p. 5463
8.9.2.2.1.5Test requirement  p. 5463
8.9.2.2.1_1TDD PHICH Transmit Diversity for UE category 1bis  p. 5463
8.10Demodulation (4 receiver antenna ports)  p. 5464
8.10.1PDSCH  p. 5464
8.10.1.1FDD (Fixed Reference Channel)  p. 5464
8.10.1.1.1FDD PDSCH Transmit Diversity 2x4  p. 5464
8.10.1.1.2FDD PDSCH Open Loop Spatial Multiplexing 2x4  p. 5466
8.10.1.1.3FDD PDSCH Closed Loop Single Layer Spatial Multiplexing 2x4 with TM4 Interference Model - Enhanced Performance Requirement Type A  p. 5469
8.10.1.1.4FDD PDSCH Closed Loop Spatial Multiplexing 4x4  p. 5473
8.10.1.1.5FDD PDSCH Single-layer Spatial Multiplexing 2x4 on antenna ports 7 or 8 with TM9 interference model - Enhanced Performance Requirement Type A  p. 5476
8.10.1.1.6FDD Dual-Layer Spatial Multiplexing 2x4 (User-Specific Reference Symbols)  p. 5484
8.10.1.1.7FDD Open-loop spatial multiplexing, 3 Layer Multiplexing with 4 Tx Antenna Ports  p. 5490
8.10.1.1.8FDD Closed-loop spatial multiplexing performance, 4 Layers spatial multiplexing 4 Tx antennas  p. 5493
8.10.1.1.9FDD 4 Layer Spatial Multiplexing (User-Specific Reference Symbols)  p. 5496
8.10.1.1.9.1Test purpose  p. 5496
8.10.1.1.9.2Test applicability  p. 5496
8.10.1.1.9.3Minimum conformance requirements  p. 5496
8.10.1.1.9.4Test description  p. 5498
8.10.1.1.9.4.2Test procedure  p. 5498
8.10.1.1.9.4.3Message contents  p. 5498
8.10.1.1.9.5Test requirement  p. 5501
8.10.1.2TDD (Fixed Reference Channel)  p. 5501
8.10.1.2.1TDD PDSCH Transmit Diversity 2x4  p. 5501
8.10.1.2.2TDD PDSCH Open Loop Spatial Multiplexing 2x4  p. 5503
8.10.1.2.3TDD PDSCH Closed Loop Single Layer Spatial Multiplexing 2x4 with TM4 Interference Model - Enhanced Performance Requirement Type A  p. 5505
8.10.1.2.4TDD PDSCH Closed Loop Spatial Multiplexing 4x4  p. 5510
8.10.1.2.5TDD PDSCH Single-layer Spatial Multiplexing 2x4 on antenna ports 7 or 8 with TM9 interference model - Enhanced Performance Requirement Type A  p. 5513
8.10.1.2.6TDD Dual-Layer Spatial Multiplexing 2x4 (User-Specific Reference Symbols)  p. 5520
8.10.1.2.6.1Test purpose  p. 5520
8.10.1.2.6.2Test applicability  p. 5520
8.10.1.2.6.3Minimum conformance requirements  p. 5520
8.10.1.2.6.4Test description  p. 5522
8.10.1.2.6.4.2Test procedure  p. 5522
8.10.1.2.6.4.3Message contents  p. 5522
8.10.1.2.6.5Test requirement  p. 5523
8.10.1.2.7TDD Open-loop spatial multiplexing, 3 Layer Multiplexing with 4 Tx Antenna Ports  p. 5525
8.10.1.2.8TDD Closed-loop spatial multiplexing performance, 4 Layers spatial multiplexing 4 Tx antennas  p. 5528
8.10.1.2.9TDD 4 Layer Spatial Multiplexing (User-Specific Reference Symbols)  p. 5531
8.10.1.2.9.1Test purpose  p. 5531
8.10.1.2.9.2Test applicability  p. 5532
8.10.1.2.9.3Minimum conformance requirements  p. 5532
8.10.1.2.9.4Test description  p. 5533
8.10.1.2.9.4.2Test procedure  p. 5533
8.10.1.2.9.4.3Message contents  p. 5533
8.10.1.2.9.5Test requirement  p. 5536
8.10.2PCFICH/PDCCH  p. 5536
8.10.2.1FDD  p. 5536
8.10.2.1.1FDD PCFICH/PDCCH Single-antenna Port Performance 1x4  p. 5536
8.10.2.1.1.1Test purpose  p. 5536
8.10.2.1.1.2Test applicability  p. 5536
8.10.2.1.1.3Minimum conformance requirements  p. 5536
8.10.2.1.1.4Test description  p. 5537
8.10.2.1.1.4.1Initial conditions  p. 5537
8.10.2.1.1.4.2Test procedure  p. 5537
8.10.2.1.1.4.3Message contents  p. 5538
8.10.2.1.1.5Test requirement  p. 5538
8.10.2.1.2FDD PCFICH/PDCCH Transmit Diversity 2x4  p. 5538
8.10.2.1.2.1Test purpose  p. 5538
8.10.2.1.2.2Test applicability  p. 5538
8.10.2.1.2.3Minimum conformance requirements  p. 5538
8.10.2.1.2.4Test description  p. 5539
8.10.2.1.2.4.1Initial conditions  p. 5539
8.10.2.1.2.4.2Test procedure  p. 5539
8.10.2.1.2.4.3Message contents  p. 5540
8.10.2.1.2.5Test requirement  p. 5540
8.10.2.1.3FDD PCFICH/PDCCH Transmit Diversity 4x4  p. 5540
8.10.2.1.3.1Test purpose  p. 5540
8.10.2.1.3.2Test applicability  p. 5540
8.10.2.1.3.3Minimum conformance requirements  p. 5541
8.10.2.1.3.4Test description  p. 5541
8.10.2.1.3.4.1Initial conditions  p. 5541
8.10.2.1.3.4.2Test procedure  p. 5542
8.10.2.1.3.4.3Message contents  p. 5542
8.10.2.1.3.5Test requirement  p. 5542
8.10.2.2TDD  p. 5543
8.10.2.2.1TDD PCFICH/PDCCH Single-antenna Port Performance 1x4  p. 5543
8.10.2.2.1.1Test purpose  p. 5543
8.10.2.2.1.2Test applicability  p. 5543
8.10.2.2.1.3Minimum conformance requirements  p. 5543
8.10.2.2.1.4Test description  p. 5544
8.10.2.2.1.4.1Initial conditions  p. 5544
8.10.2.2.1.4.2Test procedure  p. 5544
8.10.2.2.1.4.3Message contents  p. 5544
8.10.2.2.1.5Test requirement  p. 5544
8.10.2.2.2TDD PCFICH/PDCCH Transmit Diversity 2x4  p. 5545
8.10.2.2.2.1Test purpose  p. 5545
8.10.2.2.2.2Test applicability  p. 5545
8.10.2.2.2.3Minimum conformance requirements  p. 5545
8.10.2.2.2.4Test description  p. 5546
8.10.2.2.2.4.1Initial conditions  p. 5546
8.10.2.2.2.4.2Test procedure  p. 5546
8.10.2.2.2.4.3Message contents  p. 5546
8.10.2.2.2.5Test requirement  p. 5547
8.10.2.2.3TDD PCFICH/PDCCH Transmit Diversity 4x4  p. 5547
8.10.2.2.3.1Test purpose  p. 5547
8.10.2.2.3.2Test applicability  p. 5547
8.10.2.2.3.3Minimum conformance requirements  p. 5547
8.10.2.2.3.4Test description  p. 5548
8.10.2.2.3.4.1Initial conditions  p. 5548
8.10.2.2.3.4.2Test procedure  p. 5549
8.10.2.2.3.4.3Message contents  p. 5549
8.10.2.2.3.5Test requirement  p. 5550
8.10.3PHICH  p. 5550
8.10.3.1FDD  p. 5550
8.10.3.1.1FDD PHICH Single-antenna Port Performance 1x4  p. 5550
8.10.3.1.2FDD PHICH Transmit Diversity 2x4  p. 5552
8.10.3.1.3FDD PHICH Transmit Diversity 4x4  p. 5555
8.10.3.2TDD  p. 5557
8.10.3.2.1TDD PHICH Single-antenna Port Performance 1x4  p. 5557
8.10.3.2.2TDD PHICH Transmit Diversity 2x4  p. 5560
8.10.3.2.3TDD PHICH Transmit Diversity 4x4  p. 5562
8.10.4ePDCCH  p. 5565
8.10.4.1Distributed Transmission with 4Rx  p. 5565
8.10.4.1.1FDD distributed EPDCCH performance 2x4  p. 5565
8.10.4.1.1.1Test purpose  p. 5565
8.10.4.1.1.2Test applicability  p. 5565
8.10.4.1.1.3Minimum conformance requirements  p. 5565
8.10.4.1.1.4Test description  p. 5566
8.10.4.1.1.5Test requirement  p. 5567
8.10.4.1.2TDD distributed EPDCCH performance 2x4  p. 5567
8.10.4.1.2.1Test purpose  p. 5567
8.10.4.1.2.2Test applicability  p. 5567
8.10.4.1.2.3Minimum conformance requirements  p. 5568
8.10.4.1.2.4Test description  p. 5569
8.10.4.1.2.5Test requirement  p. 5570
8.10.4.2Localized Transmission with TM9 2x4  p. 5570
8.10.4.2.1FDD localized EPDCCH performance with TM9 2x4  p. 5570
8.10.4.2.1.1Test purpose  p. 5570
8.10.4.2.1.2Test applicability  p. 5570
8.10.4.2.1.3Minimum conformance requirements  p. 5570
8.10.4.2.1.4Test description  p. 5572
8.10.4.2.1.5Test requirement  p. 5573
8.10.4.2.2TDD localized EPDCCH performance with TM9 2x4  p. 5573
8.10.4.2.2.1Test purpose  p. 5573
8.10.4.2.2.2Test applicability  p. 5573
8.10.4.2.2.3Minimum conformance requirements  p. 5573
8.10.4.2.2.4Test description  p. 5575
8.10.4.2.2.5Test requirement  p. 5576
8.11Demodulation (UE supporting coverage enhancement)  p. 5576
8.11.1PDSCH  p. 5576
8.11.1.1FDD and half-duplex FDD (Fixed Reference Channel)  p. 5576
8.11.1.1.1FDD and half-duplex FDD Closed-loop spatial multiplexing performance for UE supporting CE  p. 5577
8.11.1.1.2FDD and half-duplex FDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 for UE supporting CE  p. 5581
8.11.1.1.3Transmit diversity performance (Cell-Specific Reference Symbols)  p. 5586
8.11.1.1.3.1FDD and half-duplex FDD PDSCH Transmit Diversity 2x1 for UE category M1  p. 5586
8.11.1.1.3.1_1FDD and half-duplex FDD PDSCH Transmit Diversity 2x1 for UE category M1 (CEmodeB)  p. 5591
8.11.1.1.3.2FDD and half-duplex FDD PDSCH Transmit Diversity 2x1 for UE category M2  p. 5592
8.11.1.1.3.2_1FDD and half-duplex FDD PDSCH Transmit Diversity 2x1 for UE category M2 (CEmodeB)  p. 5595
8.11.1.2TDD (Fixed Reference Channel)  p. 5596
8.11.1.2.1TDD Closed-loop spatial multiplexing performance for CE UE in CE Mode A (Cell-Specific Reference Symbols)  p. 5597
8.11.1.2.2TDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 for CE UE in CE Mode A  p. 5600
8.11.1.2.3Transmit diversity performance (Cell-Specific Reference Symbols)  p. 5603
8.11.1.2.3.1TDD PDSCH Transmit Diversity for UE category M1  p. 5603
8.11.1.2.3.1_1TDD PDSCH Transmit Diversity for UE category M1 (CEModeB)  p. 5607
8.11.1.2.3.2TDD PDSCH 2 Tx Antenna Port supporting wideband transmission for UE category M2  p. 5608
8.11.1.2.3.2_1TDD PDSCH 2 Tx Antenna Port supporting wideband transmission for UE category M2 (CEModeB)  p. 5611
8.11.2MPDCCH  p. 5612
8.11.2.1FDD and HD-FDD  p. 5612
8.11.2.1.1FDD and HD-FDD demodulation of MPDCCH in CE Mode A  p. 5612
8.11.2.1.1.1Test purpose  p. 5612
8.11.2.1.1.2Test applicability  p. 5612
8.11.2.1.1.3Minimum conformance requirements  p. 5612
8.11.2.1.1.4Test description  p. 5613
8.11.2.1.1.5Test requirement  p. 5615
8.11.2.1.2FDD and half-duplex FDD demodulation of MPDCCH in CE Mode B  p. 5615
8.11.2.1.2.1Test purpose  p. 5615
8.11.2.1.2.2Test applicability  p. 5615
8.11.2.1.2.3Minimum conformance requirements  p. 5615
8.11.2.1.2.4Test description  p. 5616
8.11.2.1.2.5Test requirement  p. 5618
8.11.2.2TDD  p. 5618
8.11.2.2.1TDD demodulation of MPDCCH in CE Mode A  p. 5618
8.11.2.2.1.1Test purpose  p. 5618
8.11.2.2.1.2Test applicability  p. 5618
8.11.2.2.1.3Minimum conformance requirements  p. 5618
8.11.2.2.1.4Test description  p. 5620
8.11.2.2.1.5Test requirement  p. 5621
8.11.2.2.2TDD demodulation of MPDCCH in CE Mode B  p. 5621
8.11.2.2.2.1Test purpose  p. 5621
8.11.2.2.2.2Test applicability  p. 5621
8.11.2.2.2.3Minimum conformance requirements  p. 5621
8.11.2.2.2.4Test description  p. 5623
8.11.2.2.2.5Test requirement  p. 5624
8.11.3Demodulation of PBCH (enhanced coverage)  p. 5625
8.12Demodulation of Narrowband IoT  p. 5625
8.12.1NPDSCH  p. 5625
8.12.1.1Half-duplex FDD  p. 5625
8.12.1.1.1Demodulation of NPDSCH (Cell-Specific Reference Symbols) in In-band mode for category NB1 and NB2  p. 5626
8.12.1.1.2Demodulation of NPDSCH (Cell-Specific Reference Symbols) in standalone and Guard-band mode for category NB1 and NB2  p. 5629
8.12.1.1.3Demodulation of NPDSCH (Cell-Specific Reference Symbols) in standalone for NB2  p. 5631
8.12.2NPDCCH  p. 5633
8.12.2.1Half-duplex FDD  p. 5633
8.12.2.1.1Demodulation of NPDCCH single-antenna performance for category NB1 and NB2  p. 5635
8.12.2.1.2Demodulation of NPDCCH Transmit diversity performance for category NB1 and NB2  p. 5637
8.13Demodulation of PDSCH CA and DC (4 receiver antenna ports)  p. 5640
8.13.1FDD (CA and DC)  p. 5640
8.13.1.1Closed Loop Multi Layer Spatial Multiplexing  p. 5640
8.13.1.1.1Closed Loop Multi Layer Spatial Multiplexing 4x4 for CA  p. 5640
8.13.1.1.1.1Minimum Requirement  p. 5640
8.13.1.1.1.2FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 (2DL CA)  p. 5643
8.13.1.1.1.3FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 (3DL CA)  p. 5648
8.13.1.1.1.4FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 (4DL CA)  p. 5653
8.13.1.1.1.5FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 (5DL CA)  p. 5655
8.13.1.1.2-  p. 5658
8.13.1.1.3FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 with 256QAM (2DL CA)  p. 5658
8.13.1.1.4FDD PDSCH Closed Loop Four-Layer Spatial Multiplexing for CA (2DL CA)  p. 5664
8.13.1.2Dual-Layer Spatial Multiplexing (User-Specific Reference Symbols)  p. 5669
8.13.1.2.2FDD Dual-Layer Spatial Multiplexing 2x4 (User-Specific Reference Symbols) (2DL CA)  p. 5673
8.13.1.2.2.1Test purpose  p. 5673
8.13.1.2.2.2Test applicability  p. 5674
8.13.1.2.2.3Minimum conformance requirements  p. 5674
8.13.1.2.2.4Test description  p. 5674
8.13.1.2.2.5Test requirement  p. 5676
8.13.1.2.3FDD Dual-Layer Spatial Multiplexing 2x4 (User-Specific Reference Symbols) (3DL CA)  p. 5677
8.13.1.2.3.1Test purpose  p. 5677
8.13.1.2.3.2Test applicability  p. 5677
8.13.1.2.3.3Minimum conformance requirements  p. 5677
8.13.1.2.3.4Test description  p. 5678
8.13.1.2.3.5Test requirement  p. 5678
8.13.1.2.4FDD Dual-Layer Spatial Multiplexing 2x4 (User-Specific Reference Symbols) (4DL CA)  p. 5680
8.13.1.2.4.1Test purpose  p. 5680
8.13.1.2.4.2Test applicability  p. 5680
8.13.1.2.4.3Minimum conformance requirements  p. 5680
8.13.1.2.4.4Test description  p. 5680
8.13.1.2.4.5Test requirement  p. 5680
8.13.1.2.5FDD Dual-Layer Spatial Multiplexing 2x4 (User-Specific Reference Symbols) (5DL CA)  p. 5682
8.13.1.2.5.1Test purpose  p. 5682
8.13.1.2.5.2Test applicability  p. 5682
8.13.1.2.5.3Minimum conformance requirements  p. 5682
8.13.1.2.5.4Test description  p. 5682
8.13.1.2.5.5Test requirement  p. 5683
8.13.1.3Enhanced Performance Requirements Type A Closed-loop spatial multiplexing  p. 5684
8.13.1.3.1FDD PDSCH Closed Loop Single Layer Spatial Multiplexing 2x4 with TM4 Interference Model - Enhanced Performance Requirement Type A (2DL CA)  p. 5684
8.13.1.4Enhanced Performance Requirement Type A - Single-layer Spatial Multiplexing (User-Specific Reference Symbols)  p. 5690
8.13.1.4.1FDD PDSCH Single-layer Spatial Multiplexing 2x4 on antenna ports 7 or 8 with TM9 Interference Model - Enhanced Performance Requirement Type A (2DL CA)  p. 5690
8.13.2TDD (CA and DC)  p. 5700
8.13.2.1Closed Loop Multi Layer Spatial Multiplexing  p. 5700
8.13.2.1.1Closed Loop Multi Layer Spatial Multiplexing 4x4 for CA  p. 5700
8.13.2.1.1.1Minimum Requirement  p. 5700
8.13.2.1.1.2TDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for CA (2DL CA)  p. 5702
8.13.2.1.1.3TDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for CA (3DL CA)  p. 5706
8.13.2.1.1.4TDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for CA (4DL CA)  p. 5710
8.13.2.1.1.5TDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for CA (5DL CA)  p. 5714
8.13.2.1.3TDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 with 256QAM (2DL CA)  p. 5718
8.13.2.1.3.1Test purpose  p. 5718
8.13.2.1.3.2Test applicability  p. 5719
8.13.2.1.3.3Minimum conformance requirements  p. 5719
8.13.2.1.3.4Test description  p. 5720
8.13.2.1.3.5Test requirement  p. 5724
8.13.2.1.4TDD PDSCH Closed Loop Four-Layer Spatial Multiplexing for CA (2DL CA)  p. 5724
8.13.2.1.4.1Test purpose  p. 5724
8.13.2.1.4.2Test applicability  p. 5725
8.13.2.1.4.3Minimum conformance requirements  p. 5725
8.13.2.1.4.4Test description  p. 5726
8.13.2.1.4.5Test requirement  p. 5729
8.13.2.2Dual-Layer Spatial Multiplexing (User-Specific Reference Symbols)  p. 5730
8.13.2.2.1Minimum Requirement  p. 5730
8.13.2.2.2TDD Dual-Layer Spatial Multiplexing 2x4 (User-Specific Reference Symbols) (2DL CA)  p. 5732
8.13.2.2.2.1Test purpose  p. 5732
8.13.2.2.2.2Test applicability  p. 5732
8.13.2.2.2.3Minimum conformance requirements  p. 5732
8.13.2.2.2.4Test description  p. 5732
8.13.2.2.2.5Test requirement  p. 5734
8.13.2.2.3TDD Dual-Layer Spatial Multiplexing 2x4 (User-Specific Reference Symbols) (3DL CA)  p. 5735
8.13.2.2.3.1Test purpose  p. 5735
8.13.2.2.3.2Test applicability  p. 5735
8.13.2.2.3.3Minimum conformance requirements  p. 5735
8.13.2.2.3.4Test description  p. 5735
8.13.2.2.3.5Test requirement  p. 5736
8.13.2.2.4TDD Dual-Layer Spatial Multiplexing 2x4 (User-Specific Reference Symbols) (4DL CA)  p. 5737
8.13.2.2.4.1Test purpose  p. 5737
8.13.2.2.4.2Test applicability  p. 5737
8.13.2.2.4.3Minimum conformance requirements  p. 5737
8.13.2.2.4.4Test description  p. 5737
8.13.2.2.4.5Test requirement  p. 5738
8.13.2.2.5TDD Dual-Layer Spatial Multiplexing 2x4 (User-Specific Reference Symbols) (5DL CA)  p. 5739
8.13.2.2.5.1Test purpose  p. 5739
8.13.2.2.5.2Test applicability  p. 5739
8.13.2.2.5.3Minimum conformance requirements  p. 5739
8.13.2.2.5.4Test description  p. 5739
8.13.2.2.5.5Test requirement  p. 5740
8.13.2.3Enhanced Performance Requirements Type A Closed-loop spatial multiplexing  p. 5741
8.13.2.3.1TDD PDSCH Closed Loop Single Layer Spatial Multiplexing 2x4 with TM4 Interference Model - Enhanced Performance Requirement Type A (2DL CA)  p. 5741
8.13.2.4Enhanced Performance Requirement Type A - Single-layer Spatial Multiplexing (User-Specific Reference Symbols)  p. 5747
8.13.2.4.1TDD PDSCH Single-layer Spatial Multiplexing 2x4 on antenna ports 7 or 8 with TM9 Interference Model - Enhanced Performance Requirement Type A (2DL CA)  p. 5747
8.13.3TDD-FDD (CA and DC)  p. 5755
8.13.3.1Closed Loop Multi Layer Spatial Multiplexing  p. 5755
8.13.3.1.1Closed Loop Multi Layer Spatial Multiplexing 4x4 for FDD PCell  p. 5755
8.13.3.1.1.1Minimum Requirement  p. 5755
8.13.3.1.1.2TDD-FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for FDD PCell (2DL CA)  p. 5759
8.13.3.1.1.3TDD-FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for FDD PCell (3DL CA)  p. 5764
8.13.3.1.1.4TDD-FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for FDD PCell (4DL CA)  p. 5768
8.13.3.1.1.5TDD-FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for FDD PCell (5DL CA)  p. 5771
8.13.3.1.2Closed Loop Multi Layer Spatial Multiplexing 4x4 for TDD PCell  p. 5774
8.13.3.1.2.1Minimum Requirement  p. 5774
8.13.3.1.2.2TDD-FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for TDD PCell (2DL CA)  p. 5778
8.13.3.1.2.3TDD-FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for TDD PCell (3DL CA)  p. 5782
8.13.3.1.2.4TDD-FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for TDD PCell (4DL CA)  p. 5785
8.13.3.1.2.5TDD-FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for TDD PCell (5DL CA)  p. 5788
8.13.3.2Dual-Layer Spatial Multiplexing (User-Specific Reference Symbols)  p. 5791
8.13.3.2.1Minimum Requirement Dual-Layer Spatial Multiplexing 2 Tx Antenna Port for FDD PCell  p. 5791
8.13.3.2.2Minimum Requirement Dual-Layer Spatial Multiplexing 2 Tx Antenna Port for TDD PCell  p. 5795
8.13.3.2.3TDD-FDD CA Dual-Layer Spatial Multiplexing 2x4 for FDD PCell (User-Specific Reference Symbols) (2DL CA)  p. 5798
8.13.3.2.3.1Test purpose  p. 5798
8.13.3.2.3.2Test applicability  p. 5798
8.13.3.2.3.3Minimum conformance requirements  p. 5798
8.13.3.2.3.4Test description  p. 5798
8.13.3.2.3.5Test requirement  p. 5801
8.13.3.2.4TDD-FDD CA Dual-Layer Spatial Multiplexing 2x4 for FDD PCell (User-Specific Reference Symbols) (3DL CA)  p. 5802
8.13.3.2.4.1Test purpose  p. 5802
8.13.3.2.4.2Test applicability  p. 5803
8.13.3.2.4.3Minimum conformance requirements  p. 5803
8.13.3.2.4.4Test description  p. 5803
8.13.3.2.4.5Test requirement  p. 5804
8.13.3.2.5TDD-FDD CA Dual-Layer Spatial Multiplexing 2x4 for FDD PCell (User-Specific Reference Symbols) (4DL CA)  p. 5805
8.13.3.2.5.1Test purpose  p. 5805
8.13.3.2.5.2Test applicability  p. 5805
8.13.3.2.5.3Minimum conformance requirements  p. 5805
8.13.3.2.5.4Test description  p. 5805
8.13.3.2.5.5Test requirement  p. 5806
8.13.3.2.6TDD-FDD CA Dual-Layer Spatial Multiplexing 2x4 for FDD PCell (User-Specific Reference Symbols) (5DL CA)  p. 5808
8.13.3.2.6.1Test purpose  p. 5808
8.13.3.2.6.2Test applicability  p. 5808
8.13.3.2.6.3Minimum conformance requirements  p. 5808
8.13.3.2.6.4Test description  p. 5808
8.13.3.2.6.5Test requirement  p. 5809
8.13.3.2.7TDD-FDD CA Dual-Layer Spatial Multiplexing 2x4 for TDD PCell (User-Specific Reference Symbols) (2DL CA)  p. 5811
8.13.3.2.7.1Test purpose  p. 5811
8.13.3.2.7.2Test applicability  p. 5811
8.13.3.2.7.3Minimum conformance requirements  p. 5811
8.13.3.2.7.4Test description  p. 5811
8.13.3.2.7.5Test requirement  p. 5813
8.13.3.2.8TDD-FDD CA Dual-Layer Spatial Multiplexing 2x4 for TDD PCell (User-Specific Reference Symbols) (3DL CA)  p. 5815
8.13.3.2.8.1Test purpose  p. 5815
8.13.3.2.8.2Test applicability  p. 5815
8.13.3.2.8.3Minimum conformance requirements  p. 5815
8.13.3.2.8.4Test description  p. 5815
8.13.3.2.8.5Test requirement  p. 5816
8.13.3.2.9TDD-FDD CA Dual-Layer Spatial Multiplexing 2x4 for TDD PCell (User-Specific Reference Symbols) (4DL CA)  p. 5817
8.13.3.2.9.1Test purpose  p. 5817
8.13.3.2.9.2Test applicability  p. 5817
8.13.3.2.9.3Minimum conformance requirements  p. 5817
8.13.3.2.9.4Test description  p. 5817
8.13.3.2.9.5Test requirement  p. 5818
8.13.3.2.10TDD-FDD CA Dual-Layer Spatial Multiplexing 2x4 for TDD PCell (User-Specific Reference Symbols) (5DL CA)  p. 5820
8.13.3.2.10.1Test purpose  p. 5820
8.13.3.2.10.2Test applicability  p. 5820
8.13.3.2.10.3Minimum conformance requirements  p. 5820
8.13.3.2.10.4Test description  p. 5820
8.13.3.2.10.5Test requirement  p. 5821
8.13.3.3Enhanced Performance Requirements Type A Closed-loop spatial multiplexing  p. 5823
8.13.3.3.1TDD-FDD CA PDSCH Closed Loop Single Layer Spatial Multiplexing 2x4 with TM4 Interference Model-Enhanced Performance Requirement Type A for FDD Pcell (2DL CA)  p. 5823
8.13.3.3.2TDD-FDD CA PDSCH Closed Loop Single Layer Spatial Multiplexing 2x4 with TM4 Interference Model-Enhanced Performance Requirement Type A for TDD Pcell (2DL CA)  p. 5830
8.13.3.4Enhanced Performance Requirements Type A - Single-layer Spatial Multiplexing (User-Specific Reference Symbols)  p. 5837
8.13.3.4.1TDD-FDD CA PDSCH Single-layer Spatial Multiplexing 2x4 on antenna ports 7 or 8 with TM9 Interference Model-Enhanced Performance Requirement Type A for FDD Pcell (2DL CA)  p. 5837
8.13.3.4.2TDD-FDD CA PDSCH Single-layer Spatial Multiplexing 2x4 on antenna ports 7 or 8 with TM9 Interference Model-Enhanced Performance Requirement Type A for TDD Pcell (2DL CA)  p. 5847
8.13.3.5-  p. 5858
8.13.3.6Closed-loop spatial multiplexing performance 4Tx Antenna Port with 256QAM  p. 5858
8.13.3.6.1TDD-FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 with 256QAM for FDD PCell (2DL CA)  p. 5858
8.13.3.6.2TDD-FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 with 256QAM for TDD PCell (2DL CA)  p. 5864
8.13.3.7Closed-loop spatial multiplexing performance 4Tx Antenna Port with Four layers  p. 5870
8.13.3.7.1TDD-FDD CA PDSCH Closed Loop Four-Layer Spatial Multiplexing for FDD PCell (2DL CA)  p. 5870
8.13.3.7.1.1Test purpose  p. 5870
8.13.3.7.1.2Test applicability  p. 5870
8.13.3.7.1.3Minimum conformance requirements  p. 5870
8.13.3.7.1.4Test description  p. 5872
8.13.3.7.1.5Test requirement  p. 5875
8.13.3.7.2TDD-FDD CA PDSCH Closed Loop Four-Layer Spatial Multiplexing for TDD PCell (2DL CA)  p. 5876
8.13.3.7.2.1Test purpose  p. 5876
8.13.3.7.2.2Test applicability  p. 5876
8.13.3.7.2.3Minimum conformance requirements  p. 5876
8.13.3.7.2.4Test description  p. 5878
8.13.3.7.2.5Test requirement  p. 5881
8.14Demodulation (UE supporting Short TTI)  p. 5882
8.14.1Slot-PDSCH and Subslot-PDSCH  p. 5882
8.14.1.1FDD (Fixed Reference Channel)  p. 5882
8.14.1.1.1FDD slot/subslot-PDSCH Open Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols)  p. 5883
8.14.1.1.2FDD slot/subslot-PDSCH Closed Loop Spatial Multiplexing Performance (User-Specific Reference Signals)  p. 5888
8.14.1.2TDD (Fixed Reference Channel)  p. 5894
8.14.1.2.1TDD slot-PDSCH Open Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols)  p. 5895
8.14.1.2.2TDD slot-PDSCH Closed Loop Spatial Multiplexing Performance (User-Specific Reference Signals)  p. 5899
8.14.2SPDCCH  p. 5904
8.14.2.1FDD SPDCCH Transmit diversity performance  p. 5904
8.14.2.2TDD SPDCCH Transmit diversity performance  p. 5910
9Reporting of Channel State Information  p. 5917
9.1General  p. 5917
9.1.1Applicability of requirements  p. 5917
9.1.1.1Applicability of requirements for different channel bandwidths  p. 5917
9.1.1.2Applicability and test rules for different CA configurations and bandwidth combination sets  p. 5917
9.1.1.2AApplicability and test rules for different TDD-FDD CA configurations and bandwidth combination sets  p. 5918
9.1.1.3Test coverage for different number of component carriers  p. 5919
9.1.1.4Applicability of performance requirements for 4Rx capable UEs  p. 5919
9.1.1.4.1Applicability rule and antenna connection for single carrier tests with 2Rx  p. 5919
9.1.1.4.2Applicability rule and antenna connection for CA tests with 2Rx  p. 5921
9.1.1.4.3Applicability rule and antenna connection for single carrier tests with 4Rx  p. 5922
9.1.1.5Applicability of requirements for UEs supporting coverage enhancement  p. 5922
9.2CQI Reporting under AWGN conditions  p. 5922
9.2.1CQI Reporting under AWGN conditions - PUCCH 1-0 (Cell-Specific Reference Symbols)  p. 5922
9.2.1.1FDD CQI Reporting under AWGN conditions - PUCCH 1-0  p. 5922
9.2.1.1.1Test purpose  p. 5922
9.2.1.1.2Test applicability  p. 5922
9.2.1.1.3Minimum conformance requirements  p. 5922
9.2.1.1.4Test description  p. 5924
9.2.1.1.5Test requirement  p. 5925
9.2.1.2TDD CQI Reporting under AWGN conditions - PUCCH 1-0  p. 5926
9.2.1.2.1Test purpose  p. 5926
9.2.1.2.2Test applicability  p. 5926
9.2.1.2.3Minimum conformance requirements  p. 5926
9.2.1.2.4Test description  p. 5927
9.2.1.2.5Test requirement  p. 5929
9.2.1.3-  p. 5929
9.2.1.3_CFDD CQI Reporting under AWGN conditions - PUCCH 1-0 for eICIC  p. 5929
9.2.1.3_C.1FDD CQI Reporting under AWGN conditions - PUCCH 1-0 for eICIC (non-MBSFN ABS)  p. 5929
9.2.1.4-  p. 5934
9.2.1.4_CTDD CQI Reporting under AWGN conditions - PUCCH 1-0 for eICIC  p. 5934
9.2.1.4_C.1TDD CQI Reporting under AWGN conditions - PUCCH 1-0 for eICIC (non-MBSFN ABS)  p. 5934
9.2.1.5-  p. 5941
9.2.1.5_EFDD CQI Reporting under AWGN conditions - PUCCH 1-0 for feICIC  p. 5941
9.2.1.5_E.1FDD CQI Reporting under AWGN conditions - PUCCH 1-0 for feICIC (non-MBSFN ABS)  p. 5941
9.2.1.5_E.1.1Test purpose  p. 5941
9.2.1.5_E.1.2Test applicability  p. 5941
9.2.1.5_E.1.3Minimum conformance requirements  p. 5941
9.2.1.5_E.1.4Test description  p. 5943
9.2.1.5_E.1.5Test requirement  p. 5947
9.2.1.6-  p. 5948
9.2.1.6_ETDD CQI Reporting under AWGN conditions - PUCCH 1-0 for feICIC  p. 5948
9.2.1.6_E.1TDD CQI Reporting under AWGN conditions - PUCCH 1-0 for feICIC (non-MBSFN ABS)  p. 5948
9.2.1.6_E.1.1Test purpose  p. 5948
9.2.1.6_E.1.2Test applicability  p. 5948
9.2.1.6_E.1.3Minimum conformance requirements  p. 5948
9.2.1.6_E.1.4Test description  p. 5950
9.2.1.6_E.1.5Test requirement  p. 5956
9.2.1.7FDD CQI Reporting under AWGN conditions - PUCCH 1-0 for 256QAM in DL  p. 5956
9.2.1.7.1Test purpose  p. 5956
9.2.1.7.2Test applicability  p. 5956
9.2.1.7.3Minimum conformance requirements  p. 5956
9.2.1.7.4Test description  p. 5957
9.2.1.7.5Test requirement  p. 5959
9.2.1.8TDD CQI Reporting under AWGN conditions - PUCCH 1-0 for 256QAM in DL  p. 5959
9.2.1.8.1Test purpose  p. 5959
9.2.1.8.2Test applicability  p. 5959
9.2.1.8.3Minimum conformance requirements  p. 5959
9.2.1.8.4Test description  p. 5960
9.2.1.8.5Test requirement  p. 5962
9.2.2CQI Reporting under AWGN conditions - PUCCH 1-1 (Cell-Specific Reference Symbols)  p. 5962
9.2.2.1FDD CQI Reporting under AWGN conditions - PUCCH 1-1  p. 5962
9.2.2.1.1Test purpose  p. 5962
9.2.2.1.2Test applicability  p. 5963
9.2.2.1.3Minimum conformance requirements  p. 5963
9.2.2.1.4Test description  p. 5964
9.2.2.1.5Test requirement  p. 5966
9.2.2.1_D.5Test requirement  p. 5967
9.2.2.2TDD CQI Reporting under AWGN conditions - PUCCH 1-1  p. 5967
9.2.2.2.1Test purpose  p. 5967
9.2.2.2.2Test applicability  p. 5967
9.2.2.2.3Minimum conformance requirements  p. 5967
9.2.2.2.4Test description  p. 5968
9.2.2.2.5Test requirement  p. 5971
9.2.3CQI Reporting under AWGN conditions - PUCCH 1-1 (CSI Reference Symbols)  p. 5972
9.2.3.1_DFDD CQI Reporting under AWGN conditions - PUCCH 1-1 for eDL-MIMO  p. 5972
9.2.3.1_D.1Test purpose  p. 5972
9.2.3.1_D.2Test applicability  p. 5972
9.2.3.1_D.3Minimum conformance requirements  p. 5972
9.2.3.1_D.4Test description  p. 5973
9.2.3.1_D.5Test requirement  p. 5976
9.2.3.2_DTDD CQI Reporting under AWGN conditions - PUCCH 1-1 for eDL-MIMO  p. 5977
9.2.3.2_D.1Test purpose  p. 5977
9.2.3.2_D.2Test applicability  p. 5977
9.2.3.2_D.3Minimum conformance requirements  p. 5977
9.2.3.2_D.4Test description  p. 5978
9.2.3.2_D.5Test requirement  p. 5982
9.2.4CQI Reporting under AWGN conditions - Single CSI Process  p. 5982
9.2.4.1AFDD CQI Reporting under AWGN conditions - Single CSI Process With interferenceMeasRestriction configured  p. 5982
9.2.4.1A.1Test purpose  p. 5982
9.2.4.1A.2Test applicability  p. 5983
9.2.4.1A.3Minimum conformance requirements  p. 5983
9.2.4.1A.4Test description  p. 5985
9.2.4.1A.5Test requirement  p. 5990
9.2.4.1_FFDD CQI Reporting under AWGN conditions - Single CSI Process for CoMP  p. 5991
9.2.4.1_F.1Test purpose  p. 5991
9.2.4.1_F.2Test applicability  p. 5991
9.2.4.1_F.3Minimum conformance requirements  p. 5991
9.2.4.1_F.4Test description  p. 5993
9.2.4.1_F.5Test requirement  p. 5997
9.2.4.2ATDD CQI Reporting under AWGN conditions - Single CSI Process With interferenceMeasRestriction configured  p. 5998
9.2.4.2A.1Test purpose  p. 5998
9.2.4.2A.2Test applicability  p. 5998
9.2.4.2A.3Minimum conformance requirements  p. 5998
9.2.4.2A.4Test description  p. 6000
9.2.4.2A.5Test requirement  p. 6005
9.2.4.2_FTDD CQI Reporting under AWGN conditions - Single CSI Process for CoMP  p. 6006
9.2.4.2_F.1Test purpose  p. 6006
9.2.4.2_F.2Test applicability  p. 6006
9.2.4.2_F.3Minimum conformance requirements  p. 6006
9.2.4.2_F.4Test description  p. 6008
9.2.4.2_F.5Test requirement  p. 6013
9.2.5TDD CQI Reporting under AWGN conditions - PUCCH 1-1 (when csi-SubframeSet -r12 and EIMTA-MainConfigServCell-r12 are configured)  p. 6014
9.2.5.1Test purpose  p. 6014
9.2.5.2Test applicability  p. 6014
9.2.5.3Minimum conformance requirements  p. 6014
9.2.5.4Test description  p. 6016
9.2.5.5Test requirement  p. 6021
9.2.6CQI Reporting under AWGN Conditions-PUSCH 3-0 - LAA (Cell-Specific Reference Symbols)  p. 6021
9.2.6.1LAA CQI Reporting under AWGN Conditions with Frame Structure Type 3 with FDD as Pcell (PUSCH 3-0)  p. 6021
9.2.6.1.1Test purpose  p. 6021
9.2.6.1.2Test applicability  p. 6022
9.2.6.1.3Minimum conformance requirements  p. 6022
9.2.6.1.4Test description  p. 6024
9.2.6.1.5Test requirement  p. 6028
9.2.6.2LAA CQI Reporting under AWGN Conditions with Frame Structure Type 3 with TDD as Pcell (PUSCH 3-0)  p. 6029
9.2.6.2.1Test purpose  p. 6029
9.2.6.2.2Test applicability  p. 6029
9.2.6.2.3Minimum conformance requirements  p. 6029
9.2.6.2.4Test description  p. 6031
9.2.6.2.5Test requirement  p. 6035
9.2.7CQI Reporting under AWGN Conditions-PUSCH 3-1 - LAA  p. 6036
9.2.7.1LAA CQI Reporting under AWGN Conditions with Frame Structure Type 3 with FDD as Pcell (PUSCH 3-1)  p. 6036
9.2.7.1.1Test purpose  p. 6036
9.2.7.1.2Test applicability  p. 6036
9.2.7.1.3Minimum conformance requirements  p. 6036
9.2.7.1.4Test description  p. 6039
9.2.7.1.5Test requirement  p. 6043
9.2.7.2LAA CQI Reporting under AWGN Conditions with Frame Structure Type 3 with TDD as Pcell (PUSCH 3-1)  p. 6043
9.2.7.2.1Test purpose  p. 6043
9.2.7.2.2Test applicability  p. 6043
9.2.7.2.3Minimum conformance requirements  p. 6043
9.2.7.2.4Test description  p. 6046
9.2.7.2.5Test requirement  p. 6050
9.3CQI Reporting under fading conditions  p. 6051
9.3.1Frequency-selective scheduling mode  p. 6051
9.3.1.1CQI Reporting under fading conditions - PUSCH 3-0 (Cell-Specific Reference Symbols)  p. 6051
9.3.1.1.1FDD CQI Reporting under fading conditions - PUSCH 3-0  p. 6051
9.3.1.1.2TDD CQI Reporting under fading conditions - PUSCH 3-0  p. 6055
9.3.1.1.3_4-  p. 6059
9.3.1.1.5TDD CQI Reporting under fading conditions - PUCCH 3-0 (when csi-SubframeSet -r12 is configured)  p. 6059
9.3.1.1.5.1Test purpose  p. 6059
9.3.1.1.5.2Test applicability  p. 6060
9.3.1.1.5.3Minimum conformance requirements  p. 6060
9.3.1.1.5.4Test description  p. 6062
9.3.1.1.5.5Test requirement  p. 6065
9.3.1.2CQI Reporting under fading conditions - PUSCH 3-1 (CSI Reference Symbols)  p. 6067
9.3.1.2.1_DFDD CQI Reporting under fading conditions - PUSCH 3-1 for eDL MIMO  p. 6067
9.3.1.2.2_DTDD CQI Reporting under fading conditions - PUSCH 3-1 for eDL MIMO  p. 6072
9.3.1.2.3FDD CQI Reporting under fading conditions - PUSCH 3-1 for 256QAM in DL  p. 6079
9.3.1.2.4TDD CQI Reporting under fading conditions - PUSCH 3-1 for 256QAM in DL  p. 6083
9.3.1.2.5-  p. 6089
9.3.1.2.6TDD CQI Reporting under fading conditions - PUCCH 3-1 (when csi-SubframeSet -r12 is configured with one CSI process)  p. 6089
9.3.1.2.6.1Test purpose  p. 6089
9.3.1.2.6.2Test applicability  p. 6089
9.3.1.2.6.3Minimum conformance requirements  p. 6089
9.3.1.2.6.4Test description  p. 6091
9.3.1.2.6.5Test requirement  p. 6094
9.3.1.3CQI Reporting under fading conditions - PUSCH 3-0 (Cell-Specific Reference Symbols)  p. 6096
9.3.1.3.1-  p. 6096
9.3.1.3.1_EFDD CQI Reporting under fading conditions - PUSCH 3-0 for feICIC  p. 6096
9.3.1.3.1_E.1FDD CQI Reporting under fading conditions - PUSCH 3-0 for feICIC (non-MBSFN ABS)  p. 6096
9.3.1.3.2-  p. 6101
9.3.1.3.2_ETDD CQI Reporting under fading conditions - PUSCH 3-0 for feICIC  p. 6101
9.3.1.3.2_E.1TDD CQI Reporting under fading conditions - PUSCH 3-0 for feICIC (non-MBSFN ABS)  p. 6101
9.3.2Frequency non-selective scheduling mode  p. 6108
9.3.2.1CQI Reporting under fading conditions - PUCCH 1-0 (Cell-Specific Reference Symbols)  p. 6108
9.3.2.1.1FDD CQI Reporting under fading conditions - PUCCH 1-0  p. 6108
9.3.2.1.1_1FDD CQI Reporting under fading conditions - PUCCH 1-0 (Release 9 and forward)  p. 6113
9.3.2.1.2TDD CQI Reporting under fading conditions - PUCCH 1-0  p. 6114
9.3.2.2CQI Reporting under fading conditions - PUCCH 1-1 (CSI Reference Symbols)  p. 6119
9.3.2.2.1_DFDD CQI Reporting under fading conditions - PUCCH 1-1 for eDL-MIMO  p. 6119
9.3.2.2.1_D.1Test purpose  p. 6119
9.3.2.2.1_D.2Test applicability  p. 6119
9.3.2.2.1_D.3Minimum conformance requirements  p. 6119
9.3.2.2.1_D.4Test description  p. 6120
9.3.2.2.1_D.4.2Test procedure  p. 6121
9.3.2.2.1_D.4.3Message contents  p. 6122
9.3.2.2.1_D.5Test requirement  p. 6124
9.2.3.1AFDD CQI Reporting under AWGN conditions - PUCCH 1-1 for FD-MIMO (With channelMeasRestriction configured)  p. 6125
9.2.3.2ATDD CQI Reporting under AWGN conditions - PUCCH 1-1 for FD-MIMO (With channelMeasRestriction configured)  p. 6131
9.3.2.2.2_DTDD CQI Reporting under fading conditions - PUCCH 1-1 for eDL-MIMO  p. 6139
9.3.2.2.2_D.1Test purpose  p. 6139
9.3.2.2.2_D.2Test applicability  p. 6139
9.3.2.2.2_D.3Minimum conformance requirements  p. 6139
9.3.2.2.2_D.4Test description  p. 6141
9.3.2.2.2_D.4.2Test procedure  p. 6141
9.3.2.2.2_D.4.3Message contents  p. 6142
9.3.3Frequency-selective interference  p. 6146
9.3.3.1CQI Reporting under fading conditions and frequency-selective interference - PUSCH 3-0 (Cell-Specific Reference Symbols)  p. 6146
9.3.3.1.1FDD CQI Reporting under fading conditions and frequency-selective interference - PUSCH 3-0  p. 6146
9.3.3.1.2TDD CQI Reporting under fading conditions and frequency-selective interference - PUSCH 3-0  p. 6149
9.3.4UE-selected subband CQI  p. 6152
9.3.4.1CQI Reporting under fading conditions - PUSCH 2-0 (Cell-Specific Reference Symbols)  p. 6153
9.3.4.1.1FDD CQI Reporting under fading conditions - PUSCH 2-0  p. 6153
9.3.4.1.2TDD CQI Reporting under fading conditions - PUSCH 2-0  p. 6157
9.3.4.2CQI Reporting under fading conditions - PUCCH 2-0 (Cell-Specific Reference Symbols)  p. 6161
9.3.4.2.1FDD CQI Reporting under fading conditions - PUCCH 2-0  p. 6161
9.3.4.2.2TDD CQI Reporting under fading conditions - PUCCH 2-0  p. 6166
9.3.5Additional requirements for enhanced receiver Type A  p. 6172
9.3.5.1PUCCH 1-0 (Cell-Specific Reference Symbol)  p. 6172
9.3.5.1.1FDD CQI Reporting under fading conditions - PUCCH 1-0 - Enhanced Performance Requirement Type A  p. 6172
9.3.5.1.2TDD CQI Reporting under fading conditions - PUCCH 1-0 - Enhanced Performance Requirement Type A  p. 6177
9.3.5.2PUCCH 1-1 (CSI Reference Symbol)  p. 6182
9.3.5.2.1FDD CQI Reporting under fading conditions - PUCCH 1-1 - Enhanced Performance Requirement Type A  p. 6182
9.3.5.2.2TDD CQI Reporting under fading conditions - PUCCH 1-1 - Enhanced Performance Requirement Type A  p. 6188
9.3.6CQI Reporting under fading conditions (With multiple CSI processes)  p. 6195
9.3.6.1_FFDD CQI Reporting under fading conditions with CSI processes for CoMP  p. 6195
9.3.6.1_F.1FDD CQI Reporting under fading conditions with Single CSI process for CoMP  p. 6195
9.3.6.1_F.1.1Test purpose  p. 6195
9.3.6.1_F.1.2Test applicability  p. 6195
9.3.6.1_F.1.3Minimum conformance requirements  p. 6195
9.3.6.1_F.1.4Test description  p. 6199
9.3.6.1_F.1.4.1Initial conditions  p. 6199
9.3.6.1_F.1.4.2Test procedure  p. 6199
9.3.6.1_F.1.4.3Message contents  p. 6200
9.3.6.1_F.1.5Test requirement  p. 6202
9.3.6.1_F.2FDD CQI Reporting under fading conditions with Three CSI processes for CoMP  p. 6205
9.3.6.1_F.2.1Test purpose  p. 6205
9.3.6.1_F.2.2Test applicability  p. 6205
9.3.6.1_F.2.3Minimum conformance requirements  p. 6205
9.3.6.1_F.2.4Test description  p. 6205
9.3.6.1_F.2.4.1Initial conditions  p. 6205
9.3.6.1_F.2.4.2Test procedure  p. 6205
9.3.6.1_F.2.4.3Message contents  p. 6206
9.3.6.1_F.2.5Test requirement  p. 6209
9.3.6.1_F.3FDD CQI Reporting under fading conditions with Four CSI processes for CoMP  p. 6210
9.3.6.1_F.3.1Test purpose  p. 6210
9.3.6.1_F.3.2Test applicability  p. 6210
9.3.6.1_F.3.3Minimum conformance requirements  p. 6210
9.3.6.1_F.3.4Test description  p. 6210
9.3.6.1_F.3.4.1Initial conditions  p. 6210
9.3.6.1_F.3.4.2Test procedure  p. 6210
9.3.6.1_F.3.4.3Message contents  p. 6211
9.3.6.1_F.3.5Test requirement  p. 6214
9.3.6.2_FTDD CQI Reporting under fading conditions with CSI processes for CoMP  p. 6215
9.3.6.2_F.1TDD CQI Reporting under fading conditions with Single CSI process for CoMP  p. 6215
9.3.6.2_F.1.1Test purpose  p. 6215
9.3.6.2_F.1.2Test applicability  p. 6215
9.3.6.2_F.1.3Minimum conformance requirements  p. 6215
9.3.6.2_F.1.4Test description  p. 6218
9.3.6.2_F.1.4.1Initial conditions  p. 6218
9.3.6.2_F.1.4.2Test procedure  p. 6218
9.3.6.2_F.1.4.3Message contents  p. 6219
9.3.6.2_F.1.5Test requirement  p. 6221
9.3.6.2_F.2TDD CQI Reporting under fading conditions with Three CSI processes for CoMP  p. 6224
9.3.6.2_F.2.1Test purpose  p. 6224
9.3.6.2_F.2.2Test applicability  p. 6224
9.3.6.2_F.2.3Minimum conformance requirements  p. 6224
9.3.6.2_F.2.4Test description  p. 6224
9.3.6.2_F.2.4.1Initial conditions  p. 6224
9.3.6.2_F.2.4.2Test procedure  p. 6224
9.3.6.2_F.2.4.3Message contents  p. 6225
9.3.6.2_F.2.5Test requirement  p. 6228
9.3.6.2_F.3TDD CQI Reporting under fading conditions with Four CSI processes for CoMP  p. 6229
9.3.6.2_F.3.1Test purpose  p. 6229
9.3.6.2_F.3.2Test applicability  p. 6229
9.3.6.2_F.3.3Minimum conformance requirements  p. 6229
9.3.6.2_F.3.4Test description  p. 6229
9.3.6.2_F.3.4.1Initial conditions  p. 6229
9.3.6.2_F.3.4.2Test procedure  p. 6229
9.3.6.2_F.3.4.3Message contents  p. 6230
9.3.6.2_F.3.5Test requirement  p. 6233
9.3.7PUSCH 3-2 for eDL MIMO Enhancement  p. 6234
9.3.7.1FDD CQI Reporting under fading conditions - PUSCH 3-2 for eDL MIMO Enhancement  p. 6234
9.3.7.1.1Test purpose  p. 6234
9.3.7.1.2Test applicability  p. 6234
9.3.7.1.3Minimum conformance requirements  p. 6234
9.3.7.1.4Test description  p. 6235
9.3.7.1.5Test requirement  p. 6239
9.3.7.2TDD CQI Reporting under fading conditions - PUSCH 3-2 for eDL MIMO Enhancement  p. 6240
9.3.7.2.1Test purpose  p. 6240
9.3.7.2.2Test applicability  p. 6241
9.3.7.2.3Minimum conformance requirements  p. 6241
9.3.7.2.4Test description  p. 6242
9.3.7.2.5Test requirement  p. 6247
9.3.8Additional requirements for enhanced receiver Type B  p. 6248
9.3.8.1PUCCH 1-1 (Cell-Specific Reference Symbols)  p. 6248
9.3.8.1.1FDD CQI Reporting under fading conditions - PUCCH 1-1 (Cell-Specific Reference Symbols) TM4 - Enhanced Receiver Type B  p. 6248
9.3.8.1.2TDD CQI Reporting under fading conditions - PUCCH 1-1 (Cell-Specific Reference Symbols) TM4 - Enhanced Receiver Type B  p. 6252
9.3.8.2PUCCH 1-1 (CSI Reference Symbols)  p. 6258
9.3.8.2.1FDD CQI Reporting under fading conditions - PUCCH 1-1 (CSI Reference Symbol) TM9 - Enhanced Receiver Type B  p. 6258
9.3.8.2.2TDD CQI Reporting under fading conditions - PUCCH 1-1 (CSI Reference Symbol) TM9 - Enhanced Receiver Type B  p. 6264
9.3.8.3CSI process  p. 6270
9.3.8.3.1FDD CQI Reporting under fading conditions - PUCCH 1-1 (CSI Reference Symbol) TM10 with TM9 interference - Enhanced Receiver Type B  p. 6270
9.3.8.3.2TDD CQI Reporting under fading conditions - PUCCH 1-1 (CSI Reference Symbol) TM10 with TM9 interference - Enhanced Receiver Type B  p. 6277
9.4Reporting of Precoding Matrix Indicator (PMI)  p. 6284
9.4.1Single PMI  p. 6285
9.4.1.1PMI Reporting - PUSCH 3-1 (Single PMI) (Cell-Specific Reference Symbols)  p. 6285
9.4.1.1.1FDD PMI Reporting - PUSCH 3-1 (Single PMI)  p. 6285
9.4.1.1.2TDD PMI Reporting - PUSCH 3-1 (Single PMI)  p. 6288
9.4.1.2PMI Reporting - PUCCH 2-1 (Single PMI) (Cell-Specific Reference Symbols)  p. 6291
9.4.1.2.1FDD PMI Reporting - PUCCH 2-1 (Single PMI)  p. 6291
9.4.1.2.2TDD PMI Reporting - PUCCH 2-1 (Single PMI)  p. 6295
9.4.1.3PMI Reporting - PUSCH 3-1 (Single PMI) (CSI Reference Symbols)  p. 6299
9.4.1.3.1-  p. 6299
9.4.1.3.1_DFDD Reporting of PMI - PUSCH 3-1 (Single PMI) for eDL MIMO  p. 6299
9.4.1.3.2_DTDD Reporting of PMI - PUSCH 3-1 (Single PMI) for eDL-MIMO  p. 6303
9.4.1.3.3FDD PMI Reporting with 12Tx Class A codebook - PUSCH 3-1 (Single PMI) for FD-MIMO  p. 6308
9.4.1.3.4TDD PMI Reporting with 12Tx Class A codebook - PUSCH 3-1 (Single PMI) for FD-MIMO  p. 6313
9.4.1.4PMI Reporting - PUCCH 1-1 (Single PMI) (CSI Reference Symbol)  p. 6315
9.4.1.4.1FDD PMI Reporting with 4Tx enhanced codebook - PUCCH 1-1 (Single PMI) for eDL MIMO Enhancement  p. 6315
9.4.1.4.2TDD PMI Reporting with 4Tx enhanced codebook - PUCCH 1-1 (Single PMI) for eDL MIMO Enhancement  p. 6321
9.4.1.4.3FDD PMI Reporting with Class B alternative codebook - PUCCH 1-1 for FD-MIMO  p. 6326
9.4.1.4.4TDD PMI Reporting with Class B alternative codebook - PUCCH 1-1 for FD-MIMO  p. 6331
9.4.2Multiple PMI  p. 6336
9.4.2.1PMI Reporting - PUSCH 1-2 (Multiple PMI) (Cell-Specific Reference Symbols)  p. 6336
9.4.2.1.1FDD PMI Reporting - PUSCH 1-2 (Multiple PMI)  p. 6336
9.4.2.1.1_1FDD PMI Reporting - PUSCH 1-2 (Multiple PMI) (Release 9 and forward)  p. 6339
9.4.2.1.2TDD PMI Reporting - PUSCH 1-2 (Multiple PMI)  p. 6342
9.4.2.1.2_1TDD PMI Reporting - PUSCH 1-2 (Multiple PMI) (Release 9 and forward)  p. 6345
9.4.2.2PMI Reporting - PUSCH 2-2 (Multiple PMI) (Cell-Specific Reference Symbols)  p. 6348
9.4.2.2.1FDD PMI Reporting - PUSCH 2-2 (Multiple PMI)  p. 6348
9.4.2.2.2TDD PMI Reporting - PUSCH 2-2 (Multiple PMI)  p. 6351
9.4.2.3PMI Reporting - PUSCH 1-2 (Multiple PMI) (CSI Reference Symbols)  p. 6354
9.4.2.3.1-  p. 6354
9.4.2.3.1_DFDD PMI Reporting - PUSCH 1-2 (Multiple PMI) for eDL-MIMO  p. 6354
9.4.2.3.2_DTDD PMI Reporting - PUSCH 1-2 (Multiple PMI) for eDL-MIMO  p. 6358
9.4.2.3.3FDD PMI Reporting with 4Tx enhanced codebook - PUSCH 1-2 (Multiple PMI) for eDL-MIMO Enhancement  p. 6364
9.4.2.3.4TDD PMI Reporting with 4Tx enhanced codebook - PUSCH 1-2 (Multiple PMI) for eDL-MIMO Enhancement  p. 6368
9.4.2.3.4.1Test purpose  p. 6368
9.4.2.3.4.2Test applicability  p. 6368
9.4.2.3.4.3Minimum conformance requirements  p. 6369
9.4.2.3.4.4.2Test procedure  p. 6371
9.4.2.3.5FDD PMI Reporting with Class A 16Tx codebook - PUSCH 1-2 (Multiple PMI) for FD-MIMO  p. 6374
9.4.2.3.6TDD PMI Reporting with Class A 16Tx codebook - PUSCH 1-2 (Multiple PMI) for FD-MIMO  p. 6379
9.5Reporting of Rank Indicator (RI)  p. 6382
9.5.1RI Reporting (Cell-Specific Reference Symbols)  p. 6383
9.5.1.1FDD RI Reporting- PUCCH 1-1  p. 6383
9.5.1.1.1Test purpose  p. 6383
9.5.1.1.2Test applicability  p. 6383
9.5.1.1.3Minimum conformance requirements  p. 6383
9.5.1.1.4Test description  p. 6385
9.5.1.1.5Test requirement  p. 6387
9.5.1.1_1FDD RI Reporting- PUCCH 1-1 (Release 10)  p. 6387
9.5.1.1_1.1Test purpose  p. 6387
9.5.1.1_1.2Test applicability  p. 6387
9.5.1.1_1.3Minimum conformance requirements  p. 6387
9.5.1.1_1.4Test description  p. 6388
9.5.1.1_1.5Test requirement  p. 6389
9.5.1.1_2FDD RI Reporting- PUCCH 1-1 (Release 11)  p. 6390
9.5.1.1_2.1Test purpose  p. 6390
9.5.1.1_2.2Test applicability  p. 6390
9.5.1.1_2.3Minimum conformance requirements  p. 6390
9.5.1.1_2.4Test description  p. 6391
9.5.1.1_2.5Test requirement  p. 6392
9.5.1.2TDD RI Reporting - PUSCH 3-1  p. 6392
9.5.1.2.1Test purpose  p. 6392
9.5.1.2.2Test applicability  p. 6392
9.5.1.2.3Minimum conformance requirements  p. 6392
9.5.1.2.4Test description  p. 6393
9.5.1.2.5Test requirement  p. 6396
9.5.1.2_1TDD RI Reporting - PUSCH 3-1 (Release 10)  p. 6396
9.5.1.2_1.1Test purpose  p. 6396
9.5.1.2_1.2Test applicability  p. 6396
9.5.1.2_1.3Minimum conformance requirements  p. 6396
9.5.1.2_1.4Test description  p. 6397
9.5.1.2_1.5Test requirement  p. 6398
9.5.1.2_2TDD RI Reporting - PUSCH 3-1 (Release 11)  p. 6398
9.5.1.2_2.1Test purpose  p. 6398
9.5.1.2_2.2Test applicability  p. 6399
9.5.1.2_2.3Minimum conformance requirements  p. 6399
9.5.1.2_2.4Test description  p. 6399
9.5.1.2_2.5Test requirement  p. 6400
9.5.2RI Reporting (CSI Reference Symbols)  p. 6400
9.5.2.1-  p. 6400
9.5.2.1_DFDD RI Reporting- PUCCH 1-1 for eDL-MIMO  p. 6400
9.5.2.1_D.1Test purpose  p. 6400
9.5.2.1_D.2Test applicability  p. 6400
9.5.2.1_D.3Minimum conformance requirements  p. 6400
9.5.2.1_D.4Test description  p. 6402
9.5.2.1_D.5Test requirement  p. 6405
9.5.2.2_DTDD RI Reporting- PUCCH 1-1 for eDL-MIMO  p. 6405
9.5.2.2_D.1Test purpose  p. 6405
9.5.2.2_D.2Test applicability  p. 6405
9.5.2.2_D.3Minimum conformance requirements  p. 6405
9.5.2.2_D.4Test description  p. 6407
9.5.2.2_D.5Test requirement  p. 6410
9.5.3RI Reporting (two CSI subframe sets are configured)  p. 6410
9.5.3.1_CFDD RI Reporting - PUCCH 1-0 for eICIC  p. 6410
9.5.3.1_C.1FDD RI Reporting - PUCCH 1-0 for eICIC (non-MBSFN ABS)  p. 6410
9.5.3.1_C.1.1Test purpose  p. 6410
9.5.3.1_C.1.2Test applicability  p. 6410
9.5.3.1_C.1.3Minimum conformance requirements  p. 6411
9.5.3.1_C.1.4Test description  p. 6413
9.5.3.1_C.1.4.1Initial conditions  p. 6413
9.5.3.1_C.1.4.2Test procedure  p. 6414
9.5.3.1_C.1.4.3Message contents  p. 6414
9.5.3.1_C.1.5Test requirement  p. 6416
9.5.3.2_CTDD RI Reporting - PUCCH 1-0 for eICIC  p. 6416
9.5.3.2_C.1TDD RI Reporting - PUCCH 1-0 for eICIC (non-MBSFN ABS)  p. 6416
9.5.3.2_C.1.1Test purpose  p. 6416
9.5.3.2_C.1.2Test applicability  p. 6417
9.5.3.2_C.1.3Minimum conformance requirements  p. 6417
9.5.3.2_C.1.4Test description  p. 6419
9.5.3.2_C.1.4.1Initial conditions  p. 6419
9.5.3.2_C.1.4.2Test procedure  p. 6420
9.5.3.2_C.1.4.3Message contents  p. 6420
9.5.3.2_C.1.5Test requirement  p. 6422
9.5.4RI Reporting (two CSI subframe sets and CRS assistance information are configured)  p. 6423
9.5.4.1_EFDD RI Reporting - PUCCH 1-0 for feICIC  p. 6423
9.5.4.1_E.1FDD RI Reporting - PUCCH 1-0 for feICIC (non-MBSFN ABS)  p. 6423
9.5.4.1_E.1.1Test purpose  p. 6423
9.5.4.1_E.1.2Test applicability  p. 6423
9.5.4.1_E.1.3Minimum conformance requirements  p. 6423
9.5.4.1_E.1.4Test description  p. 6425
9.5.4.1_E.1.4.1Initial conditions  p. 6425
9.5.4.1_E.1.4.2Test procedure  p. 6426
9.5.4.1_E.1.4.3Message contents  p. 6426
9.5.4.1_E.1.5Test requirement  p. 6429
9.5.4.2_ETDD RI Reporting - PUCCH 1-0 for feICIC  p. 6429
9.5.4.2_E.1TDD RI Reporting - PUCCH 1-0 for feICIC (non-MBSFN ABS)  p. 6429
9.5.4.2_E.1.1Test purpose  p. 6429
9.5.4.2_E.1.2Test applicability  p. 6429
9.5.4.2_E.1.3Minimum conformance requirements  p. 6429
9.5.4.2_E.1.4Test description  p. 6432
9.5.4.2_E.1.4.1Initial conditions  p. 6432
9.5.4.2_E.1.4.2Test procedure  p. 6433
9.5.4.2_E.1.4.3Message contents  p. 6433
9.5.4.2_E.1.5Test requirement  p. 6437
9.5.5RI Reporting (with CSI processes)  p. 6437
9.5.5.1_FFDD RI Reporting with CSI processes for CoMP  p. 6437
9.5.5.1_F.1FDD RI Reporting with Single CSI process for CoMP  p. 6437
9.5.5.1_F.1.1Test purpose  p. 6437
9.5.5.1_F.1.2Test applicability  p. 6437
9.5.5.1_F.1.3Minimum conformance requirements  p. 6437
9.5.5.1_F.1.4Test description  p. 6439
9.5.5.1_F.1.4.1Initial conditions  p. 6439
9.5.5.1_F.1.4.2Test procedure  p. 6440
9.5.5.1_F.1.4.3Message contents  p. 6440
9.5.5.1_F.1.5Test requirement  p. 6443
9.5.5.1_F.2FDD RI Reporting with Multiple CSI processes for CoMP  p. 6445
9.5.5.1_F.2.1Test purpose  p. 6445
9.5.5.1_F.2.2Test applicability  p. 6445
9.5.5.1_F.2.3Minimum conformance requirements  p. 6446
9.5.5.1_F.2.4Test description  p. 6446
9.5.5.1_F.2.4.1Initial conditions  p. 6446
9.5.5.1_F.2.4.2Test procedure  p. 6446
9.5.5.1_F.2.4.3Message contents  p. 6447
9.5.5.1_F.2.5Test requirement  p. 6449
9.5.5.2_FTDD RI Reporting with CSI processes for CoMP  p. 6449
9.5.5.2_F.1TDD RI Reporting with Single CSI process for CoMP  p. 6449
9.5.5.2_F.1.1Test purpose  p. 6449
9.5.5.2_F.1.2Test applicability  p. 6449
9.5.5.2_F.1.3Minimum conformance requirements  p. 6449
9.5.5.2_F.1.4Test description  p. 6452
9.5.5.2_F.1.4.1Initial conditions  p. 6452
9.5.5.2_F.1.4.2Test procedure  p. 6452
9.5.5.2_F.1.4.3Message contents  p. 6453
9.5.5.2_F.1.5Test requirement  p. 6455
9.5.5.2_F.2TDD RI Reporting with Multiple CSI processes for CoMP  p. 6457
9.5.5.2_F.2.1Test purpose  p. 6457
9.5.5.2_F.2.2Test applicability  p. 6457
9.5.5.2_F.2.3Minimum conformance requirements  p. 6457
9.5.5.2_F.2.4Test description  p. 6457
9.5.5.2_F.2.4.1Initial conditions  p. 6457
9.5.5.2_F.2.4.2Test procedure  p. 6458
9.5.5.2_F.2.4.3Message contents  p. 6458
9.5.5.2_F.2.5Test requirement  p. 6461
9.6Additional requirements for carrier aggregation  p. 6461
9.6.1Periodic reporting on multiple cells (Cell-Specific Reference Symbols)  p. 6461
9.6.1.1_AFDD CQI Reporting under AWGN conditions - PUCCH 1-0 for CA  p. 6461
9.6.1.1_A.1FDD CQI Reporting under AWGN conditions - PUCCH 1-0 for CA(2DL CA)  p. 6461
9.6.1.1_A.1.1Test purpose  p. 6461
9.6.1.1_A.1.2Test applicability  p. 6461
9.6.1.1_A.1.3Minimum conformance requirements  p. 6461
9.6.1.1_A.1.4Test description  p. 6462
9.6.1.1_A.1.4.1Initial conditions  p. 6462
9.6.1.1_A.1.4.2Test procedure  p. 6463
9.6.1.1_A.1.4.3Message contents  p. 6463
9.6.1.1_A.1.5Test requirement  p. 6466
9.6.1.1_A.2FDD CQI Reporting under AWGN conditions - PUCCH 1-0 for CA (3DL CA)  p. 6466
9.6.1.1_A.2.1Test purpose  p. 6466
9.6.1.1_A.2.2Test applicability  p. 6466
9.6.1.1_A.2.3Minimum conformance requirements  p. 6466
9.6.1.1_A.2.4Test description  p. 6467
9.6.1.1_A.2.4.1Initial conditions  p. 6467
9.6.1.1_A.2.4.2Test procedure  p. 6468
9.6.1.1_A.2.4.3Message contents  p. 6469
9.6.1.1_A.2.5Test requirement  p. 6471
9.6.1.1_A.3FDD CQI Reporting under AWGN conditions - PUCCH 1-0 for CA (4DL CA)  p. 6471
9.6.1.1_A.3.1Test purpose  p. 6471
9.6.1.1_A.3.2Test applicability  p. 6471
9.6.1.1_A.3.3Minimum conformance requirements  p. 6471
9.6.1.1_A.3.4Test description  p. 6472
9.6.1.1_A.3.4.1Initial conditions  p. 6472
9.6.1.1_A.3.4.2Test procedure  p. 6473
9.6.1.1_A.3.5Test requirement  p. 6476
9.6.1.1_A.4FDD CQI Reporting under AWGN conditions - PUCCH 1-0 for CA (5DL CA)  p. 6476
9.6.1.1_A.4.1Test purpose  p. 6476
9.6.1.1_A.4.2Test applicability  p. 6476
9.6.1.1_A.4.3Minimum conformance requirements  p. 6476
9.6.1.1_A.4.4Test description  p. 6478
9.6.1.1_A.4.4.1Initial conditions  p. 6478
9.6.1.1_A.4.4.2Test procedure  p. 6478
9.6.1.1_A.4.4.3Message contents  p. 6479
9.6.1.1_A.4.5Test requirement  p. 6481
9.6.1.1_A.5FDD CQI Reporting under AWGN conditions - PUCCH 1-0 for CA (6DL CA)  p. 6482
9.6.1.1_A.6FDD CQI Reporting under AWGN conditions - PUCCH 1-0 for CA (7DL CA)  p. 6487
9.6.1.2_ATDD CQI Reporting under AWGN conditions - PUCCH 1-0 for CA  p. 6492
9.6.1.2_A.1TDD CQI Reporting under AWGN conditions - PUCCH 1-0 for CA (2DL CA)  p. 6492
9.6.1.2_A.1.1Test purpose  p. 6492
9.6.1.2_A.1.2Test applicability  p. 6492
9.6.1.2_A.1.3Minimum conformance requirements  p. 6492
9.6.1.2_A.1.4Test description  p. 6493
9.6.1.2_A.1.4.1Initial conditions  p. 6493
9.6.1.2_A.1.4.2Test procedure  p. 6494
9.6.1.2_A.1.4.3Message contents  p. 6494
9.6.1.2_A.1.5Test requirement  p. 6497
9.6.1.2_A.2TDD CQI Reporting under AWGN conditions - PUCCH 1-0 for CA (3DL CA)  p. 6497
9.6.1.2_A.2.1Test purpose  p. 6497
9.6.1.2_A.2.2Test applicability  p. 6497
9.6.1.2_A.2.3Minimum conformance requirements  p. 6497
9.6.1.2_A.2.4Test description  p. 6498
9.6.1.2_A.2.4.1Initial conditions  p. 6498
9.6.1.2_A.2.4.2Test procedure  p. 6499
9.6.1.2_A.2.5Test requirement  p. 6502
9.6.1.2_A.3TDD CQI Reporting under AWGN conditions - PUCCH 1-0 for CA (4DL CA)  p. 6502
9.6.1.2_A.3.1Test purpose  p. 6502
9.6.1.2_A.3.2Test applicability  p. 6502
9.6.1.2_A.3.3Minimum conformance requirements  p. 6502
9.6.1.2_A.3.4Test description  p. 6503
9.6.1.2_A.3.4.1Initial conditions  p. 6503
9.6.1.2_A.3.4.2Test procedure  p. 6504
9.6.1.2_A.3.5Test requirement  p. 6507
9.6.1.2_A.4TDD CQI Reporting under AWGN conditions - PUCCH 1-0 for CA (5DL CA)  p. 6507
9.6.1.2_A.4.1Test purpose  p. 6507
9.6.1.2_A.4.2Test applicability  p. 6507
9.6.1.2_A.4.3Minimum conformance requirements  p. 6508
9.6.1.2_A.4.4Test description  p. 6509
9.6.1.2_A.4.4.1Initial conditions  p. 6509
9.6.1.2_A.4.4.2Test procedure  p. 6509
9.6.1.2_A.4.5Test requirement  p. 6512
9.6.1.2_A.6TDD CQI Reporting under AWGN conditions - PUCCH 1-0 for CA (7DL CA)  p. 6515
9.6.1.3TDD-FDD CA for FDD PCell  p. 6520
9.6.1.3.1TDD FDD CA CQI Reporting under AWGN conditions - PUCCH 1-0 for FDD PCell (2DL CA)  p. 6520
9.6.1.3.1.2Test applicability  p. 6520
9.6.1.3.1.3Minimum conformance requirements  p. 6521
9.6.1.3.1.4Test description  p. 6521
9.6.1.3.1.4.1Initial conditions  p. 6521
9.6.1.3.1.4.2Test procedure  p. 6522
9.6.1.3.1.4.3Message contents  p. 6522
9.6.1.3.1.5Test requirement  p. 6525
9.6.1.3.2TDD FDD CQI Reporting under AWGN conditions - PUCCH 1-0 for FDD PCell (3DL CA)  p. 6525
9.6.1.3.2.1Test purpose  p. 6525
9.6.1.3.2.2Test applicability  p. 6525
9.6.1.3.2.3Minimum conformance requirements  p. 6526
9.6.1.3.2.4Test description  p. 6527
9.6.1.3.2.4.1Initial conditions  p. 6527
9.6.1.3.2.4.2Test procedure  p. 6527
9.6.1.3.2.5Test requirement  p. 6531
9.6.1.3.3TDD FDD CQI Reporting under AWGN conditions - PUCCH 1-0 for FDD PCell (4DL CA)  p. 6531
9.6.1.3.3.1Test purpose  p. 6531
9.6.1.3.3.2Test applicability  p. 6531
9.6.1.3.3.3Minimum conformance requirements  p. 6532
9.6.1.3.3.4Test description  p. 6533
9.6.1.3.3.4.1Initial conditions  p. 6533
9.6.1.3.3.4.2Test procedure  p. 6534
9.6.1.3.3.5Test requirement  p. 6537
9.6.1.3.4TDD FDD CQI Reporting under AWGN conditions - PUCCH 1-0 for FDD PCell (5DL CA)  p. 6537
9.6.1.3.4.1Test purpose  p. 6537
9.6.1.3.4.2Test applicability  p. 6537
9.6.1.3.4.3Minimum conformance requirements  p. 6538
9.6.1.3.4.4Test description  p. 6539
9.6.1.3.4.4.1Initial conditions  p. 6539
9.6.1.3.4.4.2Test procedure  p. 6540
9.6.1.3.4.5Test requirement  p. 6542
9.6.1.4TDD-FDD CA for TDD PCell  p. 6543
9.6.1.4.1TDD FDD CA CQI Reporting under AWGN conditions - PUCCH 1-0 for TDD PCell (2DL CA)  p. 6543
9.6.1.4.1.2Test applicability  p. 6543
9.6.1.4.1.3Minimum conformance requirements  p. 6543
9.6.1.4.1.4Test description  p. 6544
9.6.1.4.1.4.1Initial conditions  p. 6544
9.6.1.4.1.4.2Test procedure  p. 6544
9.6.1.4.1.4.3Message contents  p. 6545
9.6.1.4.1.5Test requirement  p. 6548
9.6.1.4.2TDD FDD CQI Reporting under AWGN conditions - PUCCH 1-0 for TDD PCell (3DL CA)  p. 6548
9.6.1.4.2.1Test purpose  p. 6548
9.6.1.4.2.2Test applicability  p. 6548
9.6.1.4.2.3Minimum conformance requirements  p. 6549
9.6.1.4.2.4Test description  p. 6550
9.6.1.4.2.4.1Initial conditions  p. 6550
9.6.1.4.2.4.2Test procedure  p. 6550
9.6.1.4.2.5Test requirement  p. 6553
9.6.1.4.3TDD FDD CQI Reporting under AWGN conditions - PUCCH 1-0 for TDD PCell (4DL CA)  p. 6554
9.6.1.4.3.1Test purpose  p. 6554
9.6.1.4.3.2Test applicability  p. 6554
9.6.1.4.3.3Minimum conformance requirements  p. 6554
9.6.1.4.3.4Test description  p. 6555
9.6.1.4.3.4.1Initial conditions  p. 6555
9.6.1.4.3.4.2Test procedure  p. 6556
9.6.1.4.3.5Test requirement  p. 6559
9.6.1.4.4TDD FDD CQI Reporting under AWGN conditions - PUCCH 1-0 for TDD PCell (5DL CA)  p. 6560
9.6.1.4.4.1Test purpose  p. 6560
9.6.1.4.4.2Test applicability  p. 6560
9.6.1.4.4.3Minimum conformance requirements  p. 6560
9.6.1.4.4.4Test description  p. 6561
9.6.1.4.4.4.1Initial conditions  p. 6561
9.6.1.4.4.4.2Test procedure  p. 6562
9.6.1.4.4.5Test requirement  p. 6565
9.7CSI reporting for UE DL category 0  p. 6565
9.7.1CQI reporting definition under AWGN conditions  p. 6565
9.7.1.1FDD and Half duplex FDD CQI reporting definition under AWGN conditions for UE category 0  p. 6565
9.7.1.1.1Test purpose  p. 6565
9.7.1.1.2Test applicability  p. 6565
9.7.1.1.3Minimum conformance requirements  p. 6565
9.7.1.1.4Test description  p. 6566
9.7.1.1.5Test requirement  p. 6567
9.7_1.1.1FDD CQI reporting under AWGN conditions - PUCCH 1-0 for UE category 1bis  p. 6567
9.7_1.1.1.1Test purpose  p. 6567
9.7_1.1.1.2Test applicability  p. 6567
9.7_1.1.1.3Minimum conformance requirements  p. 6567
9.7_1.1.1.4Test description  p. 6568
9.7_1.1.1.5Test requirement  p. 6569
9.7_1.1.2TDD CQI reporting under AWGN conditions - PUCCH 1-0 for UE category 1bis  p. 6569
9.7_1.1.2.1Test purpose  p. 6569
9.7_1.1.2.2Test applicability  p. 6569
9.7_1.1.2.3Minimum conformance requirements  p. 6570
9.7_1.1.2.4Test description  p. 6570
9.7_1.1.2.5Test requirement  p. 6572
9.7_1.1.3FDD CQI reporting under fading conditions - PUSCH 3-0 for UE category 1bis  p. 6572
9.7_1.1.3.1Test purpose  p. 6572
9.7_1.1.3.2Test applicability  p. 6572
9.7_1.1.3.3Minimum conformance requirements  p. 6572
9.7_1.1.3.4Test description  p. 6573
9.7_1.1.3.5Test requirement  p. 6574
9.7_1.1.4TDD CQI reporting under fading conditions - PUSCH 3-0 for UE category 1bis  p. 6574
9.7_1.1.4.1Test purpose  p. 6574
9.7_1.1.4.2Test applicability  p. 6574
9.7_1.1.4.3Minimum conformance requirements  p. 6575
9.7_1.1.4.4Test description  p. 6576
9.7_1.1.4.5Test requirement  p. 6577
9.7.1.2TDD CQI reporting definition under AWGN conditions for UE category 0  p. 6577
9.7.1.2.1Test purpose  p. 6577
9.7.1.2.2Test applicability  p. 6577
9.7.1.2.3Minimum conformance requirements  p. 6577
9.7.1.2.4Test description  p. 6578
9.7.1.2.5Test requirement  p. 6579
9.7a_1.1.2TDD CQI reporting under AWGN conditions - PUCCH 1-0 for UE category 1bis  p. 6580
9.7a_1.1.2.1Test purpose  p. 6580
9.7a_1.1.2.2Test applicability  p. 6580
9.7a_1.1.2.3Minimum conformance requirements  p. 6580
9.7a_1.1.2.4Test description  p. 6581
9.7a_1.1.2.5Test requirement  p. 6582
9.7.2CQI reporting under fading conditions  p. 6582
9.7.2.1FDD and Half duplex FDD CQI reporting definition under fading conditions for UE category 0  p. 6582
9.7.2.1.1Test purpose  p. 6582
9.7.2.1.2Test applicability  p. 6582
9.7.2.1.3Minimum conformance requirements  p. 6582
9.7.2.1.4Test description  p. 6583
9.7.2.1.5Test requirement  p. 6585
9.7.2.2TDD CQI reporting definition under fading conditions for UE category 0  p. 6586
9.7.2.2.1Test purpose  p. 6586
9.7.2.2.2Test applicability  p. 6586
9.7.2.2.3Minimum conformance requirements  p. 6586
9.7.2.2.4Test description  p. 6587
9.7.2.2.5Test requirement  p. 6589
9.8CSI reporting (UE supporting coverage enhancement)  p. 6589
9.8.1CQI reporting definition under AWGN conditions  p. 6589
9.8.1.1FDD and Half duplex FDD CQI reporting definition under AWGN conditions for UE supporting coverage enhancement  p. 6589
9.8.1.1.4Test description  p. 6590
9.8.1.2TDD CQI reporting definition under AWGN conditions for UE supporting coverage enhancement  p. 6592
9.8.1.2.4Test description  p. 6594
9.8.2UE-selected subband CQI  p. 6596
9.8.2.1FDD and half-duplex FDD UE-selected subband CQI for UE supporting coverage enhancement  p. 6596
9.8.2.1.4Test description  p. 6598
9.8.2.2TDD UE-selected subband CQI for UE supporting coverage enhancement  p. 6600
9.8.2.2.4Test description  p. 6602
9.8.3CQI reporting definition for UE supporting 64QAM under AWGN  p. 6604
9.8.3.1FDD and Half duplex FDD CQI reporting definition under AWGN conditions for UE supporting coverage enhancement and 64QAM  p. 6604
9.8.3.1.4Test description  p. 6605
9.8.3.1.5Test requirement  p. 6607
9.8.3.2TDD CQI reporting definition under AWGN conditions for UE supporting coverage enhancement and 64QAM  p. 6607
9.8.3.2.4Test description  p. 6609
9.8.4CQI reporting definition for UE supporting alternative table under AWGN  p. 6611
9.8.4.1FDD and half duplex FDD CQI reporting under AWGN conditions for UE supporting coverage enhancement and alternative table  p. 6611
9.8.4.1.4Test description  p. 6612
9.8.4.2TDD CQI reporting definition under AWGN conditions for UE supporting coverage enhancement and alternative table  p. 6614
9.8.4.2.4Test description  p. 6616
9.9CSI reporting for 4Rx UE  p. 6618
9.9.1CQI Reporting under AWGN conditions  p. 6618
9.9.1.1CQI reporting under AWGN conditions - PUCCH 1-0 with Rank 1 (Cell-Specific Reference Symbols)  p. 6618
9.9.1.1.1FDD CQI Reporting under AWGN conditions - PUCCH 1-0 with Rank 1 1x4  p. 6618
9.9.1.1.2TDD CQI Reporting under AWGN conditions - PUCCH 1-0 with Rank 1 1x4  p. 6621
9.9.1.1.2.5Test requirement  p. 6624
9.9.1.2CQI reporting under AWGN conditions - PUCCH 1-1 with Rank 2 (CSI Reference Symbols)  p. 6625
9.9.1.2.1FDD CQI Reporting under AWGN conditions - PUCCH 1-1 with Rank 2 4x4  p. 6625
9.9.1.2.2TDD CQI Reporting under AWGN conditions - PUCCH 1-1 with Rank 2 8x4  p. 6630
9.9.1.3CQI Reporting under AWGN conditions - PUCCH 1-1 (Cell-Specific Reference Symbols)  p. 6635
9.9.1.3.1FDD CQI Reporting under AWGN conditions - PUCCH 1-1 with rank 4 4x4  p. 6635
9.9.1.3.2TDD CQI Reporting under AWGN conditions - PUCCH 1-1 with rank 4 4x4  p. 6640
9.9.1.4CQI reporting under AWGN conditions - PUCCH 1-1 with Rank 3 (CSI Reference Symbols)  p. 6644
9.9.1.4.1FDD CQI Reporting under AWGN conditions - PUCCH 1-1 with Rank 3 4x4  p. 6644
9.9.1.4.2TDD CQI Reporting under AWGN conditions - PUCCH 1-1 with Rank 3 4x4  p. 6650
9.9.2CQI Reporting under fading conditions  p. 6655
9.9.2.1CQI Reporting under fading conditions - PUCCH 1-0 (Cell-Specific Reference Symbols) for Enhanced Performance Requirement Type A  p. 6655
9.9.2.1.1FDD CQI Reporting under fading conditions - PUCCH 1-0 - Enhanced Performance Requirement Type A 1x4  p. 6655
9.9.2.1.2TDD CQI Reporting under fading conditions - PUCCH 1-0 - Enhanced Performance Requirement Type A 1x4  p. 6660
9.9.2.2CQI Reporting under fading conditions - PUCCH 1-1 (CSI Reference Symbol) for Enhanced Performance Requirement Type A  p. 6665
9.9.2.2.1FDD CQI Reporting under fading conditions - PUCCH 1-1 - Enhanced Performance Requirement Type A 2x4  p. 6665
9.9.2.2.2TDD CQI Reporting under fading conditions - PUCCH 1-1 - Enhanced Performance Requirement Type A 2x4  p. 6671
9.9.3Reporting of Precoding Matrix Indicator (PMI) for 4Rx UE  p. 6678
9.9.3.1PMI Reporting - PUSCH 3-1 (Single PMI) (Cell-Specific Reference Symbols)  p. 6678
9.9.3.1.1TDD PMI Reporting - PUSCH 3-1 (Single PMI) 8x4  p. 6678
9.9.4Reporting of Rank Indicator (RI)  p. 6683
9.9.4.1RI Reporting- PUCCH 1-1 4x4  p. 6683
9.9.4.1.1FDD RI Reporting- PUCCH 1-1 4x4  p. 6683
9.9.4.1.1.1Test purpose  p. 6683
9.9.4.1.1.2Test applicability  p. 6683
9.9.4.1.1.3Minimum conformance requirements  p. 6683
9.9.4.1.1.4Test description  p. 6685
9.9.4.1.1.5Test requirement  p. 6687
9.9.4.1.2TDD RI Reporting- PUSCH 3-1 4x4  p. 6687
9.9.4.1.2.1Test purpose  p. 6687
9.9.4.1.2.2Test applicability  p. 6687
9.9.4.1.2.3Minimum conformance requirements  p. 6687
9.9.4.1.2.4Test description  p. 6689
9.9.4.1.2.5Test requirement  p. 6691
9.9.4.2RI Reporting- PUCCH 1-1 for eDL-MIMO 4x4  p. 6691
9.9.4.2.1FDD RI Reporting- PUCCH 1-1 for eDL-MIMO 4x4  p. 6691
9.9.4.2.1.1Test purpose  p. 6691
9.9.4.2.1.2Test applicability  p. 6691
9.9.4.2.1.3Minimum conformance requirements  p. 6691
9.9.4.2.1.4Test description  p. 6693
9.9.4.2.1.5Test requirement  p. 6696
9.9.4.2.2TDD RI Reporting- PUCCH 1-1 for eDL-MIMO 4x4  p. 6696
9.9.4.2.2.1Test purpose  p. 6696
9.9.4.2.2.2Test applicability  p. 6696
9.9.4.2.2.3Minimum conformance requirements  p. 6696
9.9.4.2.2.4Test description  p. 6698
9.9.4.2.2.5Test requirement  p. 6701
9.10Reporting of CSI-RS Resource Indicator (CRI)  p. 6701
9.10.1CSI-RS Resource Indicator Reporting (PUSCH 3-1)  p. 6702
9.10.1.1FDD CSI-RS Resource Indicator Reporting - PUSCH 3-1  p. 6702
9.10.1.1.1Test purpose  p. 6702
9.10.1.1.2Test applicability  p. 6702
9.10.1.1.3Minimum conformance requirements  p. 6702
9.10.1.1.4Test description  p. 6704
9.10.1.1.5Test requirement  p. 6708
9.10.1.2TDD CSI-RS Resource Indicator Reporting - PUSCH 3-1  p. 6708
9.10.1.2.1Test purpose  p. 6708
9.10.1.2.2Test applicability  p. 6708
9.10.1.2.3Minimum conformance requirements  p. 6709
9.10.1.2.4Test description  p. 6710
9.10.1.2.5Test requirement  p. 6714
9.12CSI reporting (UE supporting Short TTI)  p. 6715
9.12.1CQI Reporting under fading conditions (Cell-Specific Reference Symbols)  p. 6715
9.12.1.1FDD CQI Reporting under fading conditions for slot/subslot TTI (Cell-Specific Reference Symbols)  p. 6715
9.12.1.1.1Test purpose  p. 6715
9.12.1.1.2Test applicability  p. 6715
9.12.1.1.3Minimum conformance requirements  p. 6715
9.12.1.1.5Test requirement  p. 6721
9.12.1.2TDD CQI Reporting under fading conditions for slot/subslot TTI (Cell-Specific Reference Symbols)  p. 6722
9.12.1.2.1Test purpose  p. 6722
9.12.1.2.2Test applicability  p. 6723
9.12.1.2.3Minimum conformance requirements  p. 6723
9.12.1.2.4Test description  p. 6724
9.12.1.2.5Test requirement  p. 6727
9.12.2CQI Reporting under fading conditions (CSI Reference Symbols)  p. 6727
9.12.2.1FDD CQI Reporting under fading conditions for slot/subslot TTI (CSI Reference Symbols)  p. 6727
9.12.2.1.1Test purpose  p. 6727
9.12.2.1.2Test applicability  p. 6727
9.12.2.1.3Minimum conformance requirements  p. 6727
9.12.2.1.4Test description  p. 6730
9.12.2.1.5Test requirement  p. 6734
9.12.2.2TDD CQI Reporting under fading conditions for slot/subslot TTI (CSI Reference Symbols)  p. 6737
9.12.2.2.1Test purpose  p. 6737
9.12.2.2.2Test applicability  p. 6737
9.12.2.2.3Minimum conformance requirements  p. 6737
9.12.2.2.4Test description  p. 6739
9.12.2.2.5Test requirement  p. 6744
10MBMS Performance  p. 6746
10.1FDD MBMS performance (Fixed Reference Channel)  p. 6746
10.1.1Test purpose  p. 6746
10.1.2Test applicability  p. 6746
10.1.3Minimum conformance requirements  p. 6746
10.1.4Test description  p. 6747
10.1.4.1Initial conditions  p. 6747
10.1.4.2Test procedure  p. 6747
10.1.4.3Message contents  p. 6748
10.1.5Test requirement  p. 6749
10.1_1FDD MBMS performance (Fixed Reference Channel) (Release 13 and forward)  p. 6750
10.1_1.1Test purpose  p. 6750
10.1_1.2Test applicability  p. 6750
10.1_1.3Minimum conformance requirements  p. 6750
10.1_1.4Test description  p. 6750
10.1_1.4.1Initial conditions  p. 6750
10.1_1.4.2Test procedure  p. 6750
10.1_1.4.3Message contents  p. 6750
10.1_1.5Test requirement  p. 6750
10.2TDD MBMS performance (Fixed Reference Channel)  p. 6751
10.2.1Test purpose  p. 6751
10.2.2Test applicability  p. 6751
10.2.3Minimum conformance requirements  p. 6751
10.2.4Test description  p. 6752
10.2.4.1Initial conditions  p. 6752
10.2.4.2Test procedure  p. 6753
10.2.4.3Message contents  p. 6753
10.2.5Test requirement  p. 6755
10.2a_1TDD MBMS performance (Fixed Reference Channel) (Release 13 and forward)  p. 6756
10.2a.1Test purpose  p. 6756
10.2a.2Test applicability  p. 6756
10.2a.3Minimum conformance requirements  p. 6756
10.2a.4Test description  p. 6756
10.2a.4.1Initial conditions  p. 6756
10.2a_1.4.2Test procedure  p. 6756
10.2a.4.3Message contents  p. 6757
10.2a_1.5Test requirement  p. 6757
10.3-  p. 6757
10.4FDD with 5G terrestrial broadcast  p. 6757
10.4.0Applicability of requirements  p. 6757
10.4.1Minimum requirement for PMCH decoding  p. 6757
10.4.1.1Minimum requirement with 0.37kHz subcarrier spacing  p. 6757
10.4.1.1.1Test purpose  p. 6759
10.4.1.1.2Test applicability  p. 6759
10.4.1.1.3Test description  p. 6759
10.4.1.1.4Message contents  p. 6760
10.4.1.1.5Test requirement  p. 6762
10.4.1.2Minimum requirement with 2.5kHz subcarrier spacing  p. 6763
10.4.1.2.1Test purpose  p. 6764
10.4.1.2.2Test applicability  p. 6764
10.4.1.2.3Test description  p. 6764
10.4.1.2.4Message contents  p. 6765
10.4.1.2.5Test requirement  p. 6767
10.4.2Minimum requirement for CAS detection  p. 6767
10.4.2.1 Minimum requirement for PBCH detection  p. 6767
10.4.2.1.1Test purpose  p. 6768
10.4.2.1.2Test applicability  p. 6768
10.4.2.1.3Test description  p. 6768
10.4.2.1.4Message contents  p. 6769
10.4.2.1.5Test requirement  p. 6771
11Performance Requirement (ProSe Direct Discovery)  p. 6771
11.1General  p. 6772
11.1.1Applicability of requirements  p. 6772
11.1.2Reference DRX configuration  p. 6772
11.2Demodulation of PSDCH (single link performance)  p. 6772
11.2.1FDD PSDCH Single Link Performance (ProSe Direct Discovery)  p. 6772
11.2.1.1Test Purpose  p. 6772
11.2.1.2Test Applicability  p. 6773
11.2.1.3Minimum Conformance Requirements  p. 6773
11.2.1.4Test Description  p. 6773
11.2.1.4.1Initial Conditions  p. 6773
11.2.1.4.2Test Procedure  p. 6774
11.2.1.4.3Message Contents  p. 6774
11.2.1.5Test Requirement  p. 6775
11.2.2TDD PSDCH Single Link Performance (ProSe Direct Discovery)  p. 6775
11.2.2.1Test Purpose  p. 6776
11.2.2.2Test Applicability  p. 6776
11.2.2.3Minimum Conformance Requirements  p. 6776
11.2.2.4Test Description  p. 6777
11.2.2.4.1Initial Conditions  p. 6777
11.2.2.4.2Test Procedure  p. 6777
11.2.2.4.3Message Contents  p. 6778
11.2.2.5Test Requirement  p. 6778
11.3Power imbalance performance with two links  p. 6779
11.3.1FDD Power imbalance performance with two links  p. 6779
11.3.1.1Test Purpose  p. 6779
11.3.1.2Test Applicability  p. 6779
11.3.1.3Minimum Conformance Requirements  p. 6779
11.3.1.4Test Description  p. 6780
11.3.1.5Test Requirement  p. 6780
11.3.2TDD Power imbalance performance with two links  p. 6780
11.3.2.1Test Purpose  p. 6780
11.3.2.2Test Applicability  p. 6780
11.3.2.3Minimum Conformance Requirements  p. 6781
11.3.2.4Test Description  p. 6782
11.3.2.5Test Requirement  p. 6782
11.4Multiple timing reference test  p. 6782
11.4.1FDD Multiple timing reference test  p. 6782
11.4.1.1Test Purpose  p. 6782
11.4.1.2Test Applicability  p. 6782
11.4.1.3Minimum Conformance Requirements  p. 6782
11.4.1.4Test Description  p. 6784
11.4.1.4.1Initial Conditions  p. 6784
11.4.1.4.2Test Procedure  p. 6784
11.4.1.4.3Message Contents  p. 6784
11.4.1.5Test Requirement  p. 6784
11.5Maximum Sidelink processes test  p. 6785
11.5.1FDD maximum Sidelink processes test (ProSe Direct Discovery)  p. 6785
11.5.1.1Test Purpose  p. 6785
11.5.1.2Test Applicability  p. 6785
11.5.1.3Minimum Conformance Requirements  p. 6785
11.5.1.4Test Description  p. 6787
11.5.1.4.1Initial Conditions  p. 6787
11.5.1.4.2Test Procedure  p. 6787
11.5.1.4.3Message Contents  p. 6788
11.5.1.5Test Requirement  p. 6788
11.5.2TDD maximum Sidelink processes test (ProSe Direct Discovery)  p. 6789
11.5.2.1Test Purpose  p. 6789
11.5.2.2Test Applicability  p. 6789
11.5.2.3Minimum Conformance Requirements  p. 6789
11.5.2.4Test Description  p. 6791
11.5.2.4.1Initial Conditions  p. 6791
11.5.2.4.2Test Procedure  p. 6791
11.5.2.4.3Message Contents  p. 6792
11.5.2.5Test Requirement  p. 6793
12Performance requirement (ProSe Direct Communication)  p. 6793
12.1General  p. 6793
12.1.1Applicability of requirements  p. 6793
12.1.2Reference DRX configuration  p. 6793
12.2Demodulation of PSSCH  p. 6793
12.2.1FDD PSSCH Single Link Performance for ProSe Direct communication  p. 6793
12.2.1.1Test Purpose  p. 6794
12.2.1.2Test Applicability  p. 6794
12.2.1.3Minimum Conformance Requirements  p. 6794
12.2.1.4Test Description  p. 6796
12.2.1.4.1Initial Conditions  p. 6796
12.2.1.4.2Test Procedure  p. 6796
12.2.1.4.3Message Contents  p. 6796
12.2.1.5Test Requirement  p. 6796
12.3Demodulation of PSCCH (single link performance)  p. 6796
12.4Demodulation of PSBCH (single link performance)  p. 6796
12.5Power imbalance performance with two links  p. 6797
12.5.1FDD Power imbalance performance with two links  p. 6797
12.5.1.1Test Purpose  p. 6797
12.5.1.2Test Applicability  p. 6797
12.5.1.3Minimum Conformance Requirements  p. 6797
12.5.1.4Test Description  p. 6799
12.5.1.4.1Initial Conditions  p. 6799
12.5.1.4.2Test Procedure  p. 6799
12.5.1.4.3Message Contents  p. 6799
12.5.1.5Test Requirement  p. 6799
12.6Multiple timing reference test  p. 6800
12.7Maximum Sidelink processes test  p. 6800
12.7.1FDD Maximum Sidelink Processes for ProSe Direct communication  p. 6800
12.7.1.1Test Purpose  p. 6800
12.7.1.2Test Applicability  p. 6800
12.7.1.3Minimum Conformance Requirements  p. 6800
12.7.1.4Test Description  p. 6801
12.7.1.4.1Initial Conditions  p. 6801
12.7.1.4.2Test Procedure  p. 6802
12.7.1.4.3Message Contents  p. 6802
12.7.1.5Test Requirement  p. 6802
13FFS  p. 6802
14Performance requirement (V2X Sidelink Communication)  p. 6802
14.1General  p. 6802
14.1.1Applicability of requirements  p. 6802
14.2Demodulation of PSSCH / Non-concurrent with E-UTRA uplink transmissions  p. 6803
14.2.1Test Purpose  p. 6803
14.2.2Test Applicability  p. 6803
14.2.3Minimum Conformance Requirements  p. 6803
14.2.4Test Description  p. 6804
14.2.5Test Requirements  p. 6805
14.3Demodulation of PSCCH / Non-concurrent with E-UTRA uplink transmissions  p. 6805
14.3.1Test Purpose  p. 6805
14.3.2Test Applicability  p. 6805
14.3.3Minimum Conformance Requirements  p. 6805
14.3.4Test Description  p. 6806
14.3.5Test Requirements  p. 6807
14.4Power imbalance performance with two links / Non-concurrent with E-UTRA uplink transmissions  p. 6808
14.4.1Test Purpose  p. 6808
14.4.2Test Applicability  p. 6808
14.4.3Minimum Conformance Requirements  p. 6808
14.4.4Test Description  p. 6809
14.4.5Test Requirements  p. 6810
14.5Demodulation of PSBCH  p. 6810
14.6Demodulation of PSSCH with eNB based synchronization  p. 6810
14.6.1Test Purpose  p. 6811
14.6.2Test Applicability  p. 6811
14.6.3Minimum Conformance Requirements  p. 6811
14.6.4Test Description  p. 6812
14.6.4.1Initial conditions  p. 6812
14.6.4.2Test procedure  p. 6812
14.6.4.3Message contents  p. 6812
14.6.5Test Requirements  p. 6813
14.7Soft buffer test  p. 6813
14.7.1Test Purpose  p. 6813
14.7.2Test Applicability  p. 6813
14.7.3Minimum Conformance Requirements  p. 6814
14.7.4Test Description  p. 6814
14.7.4.1Initial conditions  p. 6814
14.7.4.2Test procedure  p. 6815
14.7.4.3Message contents  p. 6815
14.7.5Test Requirements  p. 6815
14.8PSCCH/PSSCH decoding capability test / Non-concurrent with E-UTRA uplink transmissions  p. 6816
14.8.1Test Purpose  p. 6816
14.8.2Test Applicability  p. 6816
14.8.3Minimum Conformance Requirements  p. 6816
14.8.4Test Description  p. 6817
14.8.5Test Requirement  p. 6818
14.9Sustained downlink data rate with active sidelink  p. 6819
14.9.1Test Purpose  p. 6819
14.9.2Test Applicability  p. 6819
14.9.3Minimum Conformance Requirements  p. 6819
14.9.4Test Description  p. 6820
14.9.5Test Requirements  p. 6824
A(Normative)  Measurement Channels  p. 6826
A.1General  p. 6826
A.2UL reference measurement channels  p. 6827
A.2.1General  p. 6827
A.2.1.1Applicability and common parameters  p. 6827
A.2.1.2Determination of payload size  p. 6827
A.2.1.3Overview of UL reference measurement channels  p. 6828
A.2.2Reference measurement channels for FDD  p. 6844
A.2.2.1Full RB allocation  p. 6844
A.2.2.1.1QPSK  p. 6844
A.2.2.1.216-QAM  p. 6846
A.2.2.1.364-QAM  p. 6848
A.2.2.1.4256 QAM  p. 6848
A.2.2.2Partial RB allocation  p. 6848
A.2.2.2.1QPSK  p. 6849
A.2.2.2.216-QAM  p. 6852
A.2.2.2.364-QAM  p. 6855
A.2.2.2.4256 QAM  p. 6856
A.2.2.3Reference measurement channels for sustained downlink data rate provided by lower layers  p. 6857
A.2.2.4subPRB allocation  p. 6857
A.2.3Reference measurement channels for TDD  p. 6857
A.2.3.1Full RB allocation  p. 6858
A.2.3.1.1QPSK  p. 6858
A.2.3.1.216-QAM  p. 6860
A.2.3.1.364-QAM  p. 6863
A.2.3.1.4256 QAM  p. 6863
A.2.3.2Partial RB allocation  p. 6864
A.2.3.2.1QPSK  p. 6864
A.2.3.2.216-QAM  p. 6868
A.2.3.2.364-QAM  p. 6873
A.2.3.2.4256 QAM  p. 6874
A.2.3.3Reference measurement channels for sustained downlink data rate provided by lower layers  p. 6875
A.2.3.4subPRB allocation  p. 6875
A.2.4Reference measurement channels for category NB1  p. 6876
A.2.5Reference measurement channels for LAA  p. 6878
A.2.5.1Full RB allocation  p. 6878
A.2.5.1.1QPSK  p. 6878
A.2.5.1.216QAM  p. 6879
A.2.5.1.364QAM  p. 6879
A.2.5.2Partial RB allocation  p. 6879
A.2.5.2.1QPSK  p. 6880
A.2.5.2.216QAM  p. 6880
A.2.5.2.364QAM  p. 6881
A.3DL reference measurement channels  p. 6881
A.3.1General  p. 6881
A.3.1.1Overview of DL reference measurement channels  p. 6882
A.3.2Reference measurement channel for receiver characteristics  p. 6895
A.3.2ADownlink Reference measurement channel for TX characteristics  p. 6921
A.3.2BDownlink Reference measurement channel for ProSe testing  p. 6926
A.3.3Reference measurement channel for PDSCH performance requirements (FDD)  p. 6928
A.3.3.1Single-antenna transmission (Common Reference Symbols)  p. 6928
A.3.3.2Multi-antenna transmission (Common Reference Symbols)  p. 6934
A.3.3.2.1Two antenna ports  p. 6934
A.3.3.2.2Four antenna ports  p. 6940
A.3.3.3Reference Measurement Channel for UE-Specific Reference Symbols  p. 6942
A.3.3.3.0Two antenna ports (no CSI-RS)  p. 6942
A.3.3.3.1Two antenna port (CSI-RS)  p. 6944
A.3.3.3.2Four antenna ports (CSI-RS)  p. 6946
A.3.3.3.2AEight antenna ports (CSI-RS)  p. 6950
A.3.3.3.3Twelve antenna port (CSI-RS)  p. 6951
A.3.4Reference measurement channel for PDSCH performance requirements (TDD)  p. 6954
A.3.4.1Single-antenna transmission (Common Reference Symbols)  p. 6954
A.3.4.2Multi-antenna transmission (Common Reference Symbols)  p. 6961
A.3.4.2.1Two antenna ports  p. 6961
A.3.4.2.2Four antenna ports  p. 6970
A.3.4.3Reference Measurement Channels for UE-Specific Reference Symbols  p. 6974
A.3.4.3.3Two antenna ports (CSI-RS)  p. 6977
A.3.4.3.4Four antenna ports (CSI-RS)  p. 6981
A.3.4.3.5Eight antenna ports (CSI-RS)  p. 6984
A.3.4.3.6Twelve antenna ports (CSI-RS)  p. 6987
A.3.5Reference measurement channels for PDCCH/PCFICH performance requirements  p. 6989
A.3.5.1FDD  p. 6989
A.3.5.2TDD  p. 6990
A.3.5.3LAA  p. 6992
A.3.6Reference measurement channels for PHICH performance requirements  p. 6993
A.3.7[FFS]  p. 6994
A.3.8Reference measurement channels for MBMS performance requirements  p. 6994
A.3.8.1FDD  p. 6994
A.3.8.2TDD  p. 6995
A.3.9Reference measurement channels for sustained downlink data rate provided by lower layers  p. 6997
A.3.9.1FDD  p. 6997
A.3.9.2TDD  p. 7000
A.3.9.3FDD (EPDCCH scheduling)  p. 7007
A.3.9.4TDD (EPDCCH scheduling)  p. 7008
A.3.10Reference Measurement Channels for EPDCCH performance requirements  p. 7009
A.3.10.1FDD  p. 7009
A.3.10.2TDD  p. 7010
A.3.11Reference Measurement Channels for MPDCCH performance requirements  p. 7010
A.3.11.1FDD and half-duplex FDD  p. 7010
A.3.11.2TDD  p. 7011
A.3.12Reference measurement channels for NPDSCH performance requirements  p. 7012
A.3.15Reference Measurement Channels for LAA SCell with frame structure Type-3  p. 7016
A.3.15.1Multi-antenna transmission (Common Reference Symbols)  p. 7016
A.3.15.1.1Four antenna ports  p. 7016
A.3.15.2Reference Measurement Channel for UE-Specific Reference Symbols  p. 7017
A.3.15.2.1Two antenna ports (CSI-RS)  p. 7017
A.3.16Reference measurement channels for Slot-PDSCH and Subslot-PDSCH performance requirements  p. 7018
A.3.16.1FDD  p. 7018
A.3.16.2TDD  p. 7022
A.3.17Reference measurement channels for SPDCCH performance requirements  p. 7023
A.3.17.1FDD  p. 7023
A.3.17.2TDD  p. 7023
A.3.18Reference Measurement Channels for LTE based 5G broadcast PMCH receiver requirements  p. 7024
A.3.18.1SDO  p. 7024
A.4CQI reference measurement channels  p. 7026
A.4.1Additional CSI reference measurement channels  p. 7035
A.5OFDMA Channel Noise Generator (OCNG)  p. 7037
A.5.1OCNG Patterns for FDD  p. 7037
A.5.1.1OCNG FDD pattern 1: One sided dynamic OCNG FDD pattern  p. 7037
A.5.1.2OCNG FDD pattern 2: Two sided dynamic OCNG FDD pattern  p. 7038
A.5.1.3OCNG FDD pattern 3: 49 RB OCNG allocation with MBSFN in 10 MHz  p. 7039
A.5.1.4OCNG FDD pattern 4: One sided dynamic OCNG FDD pattern for MBMS transmission  p. 7039
A.5.1.5OCNG FDD pattern 5: One sided dynamic 16QAM modulated OCNG FDD pattern  p. 7040
A.5.1.6OCNG FDD pattern 6: dynamic OCNG FDD pattern when user data is in 2 non-contiguous blocks  p. 7041
A.5.1.8OCNG FDD pattern 8: One sided dynamic OCNG FDD pattern for TM10 transmission  p. 7042
A.5.2OCNG Patterns for TDD  p. 7042
A.5.2.1OCNG TDD pattern 1: One sided dynamic OCNG TDD pattern  p. 7043
A.5.2.2OCNG TDD pattern 2: Two sided dynamic OCNG TDD pattern  p. 7043
A.5.2.3OCNG TDD pattern 3: 49 RB OCNG allocation with MBSFN in 10 MHz  p. 7044
A.5.2.4OCNG TDD pattern 4: One sided dynamic OCNG TDD pattern for MBMS transmission  p. 7045
A.5.2.5OCNG TDD pattern 5: One sided dynamic 16QAM modulated OCNG TDD pattern  p. 7045
A.5.2.6OCNG TDD pattern 6: dynamic OCNG TDD pattern when user data is in 2 non-contiguous blocks  p. 7046
A.5.2.8OCNG TDD pattern 8: One sided dynamic OCNG TDD pattern for TM10 transmission  p. 7047
A.5.3OCNG Patterns for Narrowband IoT  p. 7048
A.5.3.1Narrowband IoT OCNG pattern 1  p. 7048
A.5.4OCNG Patterns for frame structure type  p. 7049
A.5.4.1OCNG FS3 pattern 1: One sided dynamic OCNG frame structure type 3 pattern  p. 7049
A.5.4.2OCNG FS3 pattern 2: Two sided dynamic OCNG frame structure 3 pattern  p. 7050
A.6Sidelink reference measurement channels  p. 7051
A.6.1General  p. 7051
A.6.2Reference measurement channel for receiver characteristics  p. 7051
A.6.3Reference measurement channels for PSDCH performance requirements  p. 7053
A.6.4Reference measurement channels for PSCCH performance requirements  p. 7053
A.6.5Reference measurement channels for PSSCH performance requirements  p. 7054
A.6.6Reference measurement channels for PSBCH performance requirements  p. 7054
A.7Sidelink reference resource pool configurations  p. 7055
A.7.1Reference resource pool configurations for ProSe Direct Discovery demodulation tests  p. 7055
A.7.1.1FDD  p. 7055
A.7.1.2TDD  p. 7057
A.7.2Reference resource pool configurations for ProSe Direct Communication demodulation tests  p. 7059
A.7.2.1FDD  p. 7059
A.8V2X reference measurement channels  p. 7064
A.8.1General  p. 7064
A.8.2Reference measurement channel for receiver characteristics  p. 7065
A.8.3Reference measurement channel for transmitter characteristics  p. 7065
A.8.4Reference measurement for PSCCH performance requirements  p. 7067
A.8.5Reference measurement for PSSCH performance requirements  p. 7068
A.8.6Reference measurement for PSBCH performance requirements  p. 7068
A.9V2X reference resource pool configurations  p. 7069
B(Normative)  Propagation Conditions  p. 7072
B.0No interference  p. 7072
B.1Static propagation condition  p. 7072
B.1.1Definition of Additive White Gaussian Noise (AWGN) Interferer  p. 7073
B.2Multi-path fading Propagation Conditions  p. 7073
B.2.1Delay profiles  p. 7073
B.2.2Combinations of channel model parameters  p. 7074
B.2.3MIMO Channel Correlation Matrices  p. 7074
B.2.3.1Definition of MIMO Correlation Matrices  p. 7075
B.2.3.2MIMO Correlation Matrices at High, Medium and Low Level  p. 7076
B.2.3AMIMO Channel Correlation Matrices using cross polarized antennas  p. 7078
B.2.3A.1Definition of MIMO Correlation Matrices using cross polarized antennas  p. 7079
B.2.3A.2Spatial Correlation Matrices using cross polarized antennas at eNB and UE sides  p. 7079
B.2.3A.2.1Spatial Correlation Matrices at eNB side  p. 7079
B.2.3A.2.2Spatial Correlation Matrices at UE side  p. 7080
B.2.3A.3MIMO Correlation Matrices using cross polarized antennas  p. 7080
B.2.3A.4Beam steering approach  p. 7081
B.2.4Propagation conditions for CQI tests  p. 7082
B.2.5FFS  p. 7082
B.2.6MBSFN Propagation Channel Profile  p. 7082
B.2.6.2Subcarrier spacing 1.25kHz  p. 7083
B.2.6.3Subcarrier spacing 0.37kHz  p. 7084
B.2.6.4Subcarrier spacing 2.5kHz  p. 7085
B.3High speed train scenario  p. 7085
B.3AHST-SFN scenario  p. 7086
B.4Beamforming Model  p. 7090
B.4.1Single-layer random beamforming (Antenna port 5, 7 or 8)  p. 7090
B.4.2Dual-layer random beamforming (antenna ports 7 and 8)  p. 7091
B.4.3Generic beamforming model (antenna ports 7-14)  p. 7091
B.4.4Random beamforming for EPDCCH distributed transmission (Antenna port 107 and 109)  p. 7092
B.4.5Random beamforming for EPDCCH localized transmission (Antenna port 107, 108, 109 or 110)  p. 7092
B.4.6Beamforming model for CRI test  p. 7092
B.5Interference models for enhanced performance requirements Type-A  p. 7094
B.5.1Dominant interferer proportion  p. 7094
B.5.2Transmission mode 3 interference model  p. 7094
B.5.3Transmission mode 4 interference model  p. 7095
B.5.4Transmission mode 9 interference model  p. 7095
B.6Interference models for enhanced performance requirements Type-B  p. 7095
B.6.1Transmission mode 2 interference model  p. 7095
B.6.2Transmission mode 3 interference model  p. 7096
B.6.3Transmission mode 4 interference model  p. 7096
B.6.4Transmission mode 9 interference model  p. 7097
B.6.5CRS interference model  p. 7097
B.6.6Random interference model  p. 7097
B.7FFS  p. 7098
B.8Burst transmission models for Frame structure type 3  p. 7098
B.8.1Burst transmission model for one LAA SCell  p. 7098
C(Normative)  Downlink Physical Channels  p. 7100
C.0Downlink signal levels  p. 7100
C.1General  p. 7100
C.2Set-up  p. 7106
C.3Connection  p. 7109
C.3.0Measurement of Transmitter Characteristics  p. 7110
C.3.1Measurement of Receiver Characteristics  p. 7111
C.3.2Measurement of Performance requirements  p. 7113
C.3.3Aggressor cell power allocation for Measurement of Performance Requirements when ABS is Configured  p. 7115
C.3.4Power Allocation for Measurement of Performance Requirements when Quasi Co-location Type B: same Cell ID  p. 7116
C.3.5Simplified CA testing method  p. 7116
D(Normative)  Characteristics of the Interfering Signal  p. 7118
D.1General  p. 7118
D.2Interference signals  p. 7118
E(Normative)  Global In-Channel TX-Test  p. 7119
E.1General  p. 7119
E.2Signals and results  p. 7119
E.2.1Basic principle  p. 7119
E.2.2Output signal of the TX under test  p. 7119
E.2.3Reference signal  p. 7120
E.2.4Measurement results  p. 7120
E.2.5Measurement points  p. 7120
E.3Signal processing  p. 7121
E.3.1Pre FFT minimization process  p. 7121
E.3.2Timing of the FFT window  p. 7121
E.3.3Post FFT equalisation  p. 7122
E.4Derivation of the results  p. 7123
E.4.1EVM  p. 7123
E.4.2Averaged EVM  p. 7124
E.4.3In-band emissions measurement  p. 7124
E.4.4EVM equalizer spectrum flatness  p. 7126
E.4.5Frequency error and Carrier leakage  p. 7127
E.4.6EVM of Demodulation reference symbols (EVMDMRS)  p. 7127
E.4.6.11st average for EVM DMRS  p. 7128
E.4.6.2Final average for EVM DMRS  p. 7128
E.5EVM and inband emissions for PUCCH  p. 7128
E.5.1Basic principle  p. 7128
E.5.2Output signal of the TX under test  p. 7128
E.5.3Reference signal  p. 7128
E.5.4Measurement results  p. 7128
E.5.5Measurement points  p. 7129
E.5.6Pre FFT minimization process  p. 7129
E.5.7Timing of the FFT window  p. 7129
E.5.8Post FFT equalisation  p. 7129
E.5.9Derivation of the results  p. 7130
E.5.9.1EVMPUCCH  p. 7130
E.5.9.2Averaged EVMPUCCH  p. 7131
E.5.9.3In-band emissions measurement  p. 7131
E.6EVM for PRACH  p. 7132
E.6.1Basic principle  p. 7132
E.6.2Output signal of the TX under test  p. 7132
E.6.3Reference signal  p. 7132
E.6.4Measurement results  p. 7133
E.6.5Measurement points  p. 7133
E.6.6Pre FFT minimization process  p. 7133
E.6.7Timing of the FFT window  p. 7133
E.6.8Post FFT equalisation  p. 7134
E.6.9Derivation of the results  p. 7134
E.6.9.1EVMPRACH  p. 7134
E.6.9.2Averaged EVMPRACH  p. 7135
E.7EVM with exclusion period  p. 7135
E.7.1General  p. 7135
E.7.2The model  p. 7135
E.7.3Illustration  p. 7136
E.7.4Formula  p. 7139
E.8EVM for category NB1  p. 7140
E.8.1Averaged EVM  p. 7140
E.8.2EVM of Demodulation reference symbols (EVMDMRS)  p. 7140
E.8.3EVM for NPRACH  p. 7140
E.8.4Window length for category NB1  p. 7140
E.9EVM for V2X communication  p. 7140
E.9.1EVM for PSSCH and PSCCH  p. 7140
E.9.2EVM for PSBCH  p. 7140
F(Normative)  Measurement uncertainties and Test Tolerances  p. 7141
F.1Acceptable uncertainty of Test System (normative)  p. 7141
F.1.1Measurement of test environments  p. 7141
F.1.2Measurement of transmitter  p. 7142
F.1.3Measurement of receiver  p. 7168
F.1.4Measurement of performance requirements  p. 7191
F.1.5Measurement of Channel State Information reporting  p. 7239
F.2Interpretation of measurement results (normative)  p. 7254
F.3Test Tolerance and Derivation of Test Requirements (informative)  p. 7254
F.3.1Measurement of test environments  p. 7254
F.3.2Measurement of transmitter  p. 7255
F.3.3Measurement of receiver  p. 7316
F.3.4Measurement of performance requirements  p. 7342
F.3.5Measurement of Channel State Information reporting  p. 7373
G(Normative)  Statistical Testing  p. 7386
G.1General  p. 7386
G.2Statistical testing of receiver characteristics  p. 7386
G.2.1General  p. 7386
G.2.2Mapping throughput to error ratio  p. 7386
G.2.3Design of the test  p. 7387
G.2.4Numerical definition of the pass fail limits  p. 7388
G.2.5Pass fail decision rules  p. 7389
G.2.6Test conditions for receiver tests  p. 7390
G.2AStatistical testing of receiver characteristics with CA  p. 7392
G.2A.1General  p. 7392
G.2A.2Mapping throughput to error ratio  p. 7392
G.2A.3-  p. 7393
G.2A.4Pass fail limits  p. 7393
G.2A.5Void  p. …
G.2A.6Test conditions for receiver tests with CA  p. 7394
G.3Statistical testing of Performance Requirements with throughput  p. 7394
G.3.1General  p. 7394
G.3.2Mapping throughput to error ratio  p. 7395
G.3.3Design of the test  p. 7395
G.3.4Pass Fail limit  p. 7395
G.3.5Minimum Test time  p. 7396
G.3.6Test conditions for receiver performance tests  p. 7421
G.3AStatistical testing of Performance Requirements with throughput for CA/DC/LAA  p. 7427
G.3A.1General  p. 7427
G.3A.2Mapping throughput to error ratio  p. 7427
G.3A.3Design of the test  p. 7427
G.3A.4Pass Fail limit  p. 7428
G.3A.5Minimum test time  p. 7428
G.3A.6Test conditions  p. 7484
G.4Statistical testing of Performance Requirements with probability of misdetection  p. 7489
G.4.1General  p. 7489
G.4.2Mapping the UE reaction to error ratio  p. 7489
G.4.3Design of the test  p. 7489
G.4.4Numerical definition of the pass fail limits  p. 7490
G.4.5Pass fail decision rules  p. 7491
G.4.6Minimum Test time  p. 7492
G.4.7Test conditions for receiver performance tests  p. 7499
G.5Measuring throughput ratio  p. 7500
G.5.1General  p. 7500
G.5.2Establishing SNR  p. 7500
G.5.3Measuring T-put  p. 7500
G.5.4Number of samples for throughput ratios  p. 7500
G.6Statistical testing of MBMS Performance  p. 7508
G.6.1General  p. 7508
G.6.2Mapping of MBMS Packet ratio to BLER  p. 7508
G.6.3Design of the test  p. 7508
G.6.4Test time for MBMS performance tests  p. 7509
G.7Theory to derive the numbers in Table G.2.4-1 (Informative)  p. 7509
G.7.1Error Ratio (ER)  p. 7509
G.7.2Test Design  p. 7509
G.7.3Confidence level  p. 7510
G.7.4Introduction: Supplier Risk versus Customer Risk  p. 7510
G.7.5Supplier Risk versus Customer Risk  p. 7510
G.7.6Introduction: Standard test versus early decision concept  p. 7511
G.7.7Standard test versus early decision concept  p. 7511
G.7.8Selectivity  p. 7511
G.7.9Design of the test  p. 7512
G.7.10Simulation to derive the pass fail limits in Table G.2.4-1  p. 7513
G.8Statistical Testing of V2V and V2X Performance Requirements - Non concurrent with E-UTRA  p. 7514
G.8.1General  p. 7514
G.8.2Test Method for Performance Test Cases  p. 7514
G.8.3Test Time for V2V and V2X Performance Requirements with Throughput  p. 7516
G.8.4Test Time for V2V and V2X Performance Requirements with Probability of Miss-Detection  p. 7517
H(Normative)  Uplink Physical Channels  p. 7519
H.0Uplink Signal Levels  p. 7519
H.0.1Uplink Signal Levels for NB1  p. 7519
H.1General  p. 7519
H.1.1General for NB1  p. 7521
H.2Set-up  p. 7521
H.2.1Set-up for NB1  p. 7521
H.3Connection  p. 7521
H.3.0Measurement of Transmitter Characteristics  p. 7521
H.3.1Measurement of Receiver Characteristics  p. 7522
H.3.2Measurement of Performance Requirements  p. 7522
H.4Connection for NB1  p. 7522
H.4.0Measurement of Transmitter Characteristics  p. 7522
H.4.1Measurement of Receiver Characteristics  p. 7522
H.4.2Measurement of Performance Requirements  p. 7522
IHandling requirements and tests for different releases and UE capabilities  p. 7523
I.1General Considerations  p. 7523
I.2Concrete scenarios  p. 7524
I.2.1Tests for minimum requirements varying between releases, without introduction of new features  p. 7524
I.2.2Tests for CA (Carrier aggregation)  p. 7525
I.2.2.1CA Tx tests (Chapter 6)  p. 7525
I.2.2.2CA Rx tests (Chapter 7)  p. 7526
I.2.2.3CA Performance tests (Chapter 8)  p. 7526
I.2.3Tests for UL-MIMO (Uplink Multiple Antenna Transmission)  p. 7527
I.2.3.1UL-MIMO Tx tests (Chapter 6)  p. 7527
I.2.3.2UL-MIMO Rx tests (Chapter 7)  p. 7528
I.2.4Tests for eDL-MIMO (Enhanced Downlink Multiple Antenna Transmission)  p. 7528
I.2.4.1eDL MIMO Performance tests (Chapter 8)  p. 7528
I.2.4.2eDL MIMO CSI tests (Chapter 9)  p. 7528
I.2.5Tests for eICIC (Enhanced Intercarrier Interference Cancellation / Coordination)  p. 7529
I.2.5.1eICIC Performance tests (Chapter 8)  p. 7529
I.2.5.2eICIC CSI tests (Chapter 9)  p. 7530
I.2.6Tests for feICIC (Further Enhanced Non CA-based ICIC for LTE)  p. 7530
I.2.6.1feICIC Performance tests (Chapter 8)  p. 7530
I.2.6.2feICIC CSI tests (Chapter 9)  p. 7530
I.2.7Tests for DL ComP (Downlink Coordinated Multipoint Transmission)  p. 7531
I.2.7.1CoMP Performance tests (Chapter 8)  p. 7531
I.2.7.2CoMP CSI tests (Chapter 9)  p. 7531
I.2.8Tests for Further eDL-MIMO (Enhanced Downlink Multiple Antenna Transmission) Enhancement for LTE-A  p. 7531
I.2.8.1eDL MIMO Enhancement CSI tests (Chapter 9)  p. 7531
I.2.9Tests for UE category 0  p. 7532
I.2.9.1UE category 0 Tx tests (Chapter 6)  p. 7532
I.2.9.2UE category 0 Rx tests (Chapter 7)  p. 7533
I.2.9.3UE category 0 Performance tests (Chapter 8)  p. 7533
I.2.9.4UE category 0 CSI tests (Chapter 9)  p. 7533
I.2.9ATests for UE category M1  p. 7533
I.2.9A.1UE category M1 Tx tests (Chapter 6)  p. 7533
I.2.9A.2UE category M1 Rx tests (Chapter 7)  p. 7534
I.2.9A.3UE category M1 Performance tests (Chapter 8)  p. 7534
I.2.9A.4UE category M1 CSI tests (Chapter 9)  p. 7535
I.2.9BTests for UE category M2  p. 7535
I.2.9B.1UE category M2 Tx tests (Chapter 6)  p. 7535
I.2.9B.2UE category M2 Rx tests (Chapter 7)  p. 7535
I.2.9B.3UE category M2 Performance tests (Chapter 8)  p. 7535
I.2.9B.4UE category M2 CSI tests (Chapter 9)  p. 7536
I.2.10Tests for SCE-L1 (Small Cell Enhancements-Physical layer)  p. 7536
I.2.10.1SCE-L1 Receiver tests (Chapter 7)  p. 7536
I.2.10.2SCE-L1 Performance tests (Chapter 8)  p. 7537
I.2.10.3SCE-L1 CSI tests (Chapter 9)  p. 7537
I.2.11Tests for ProSe  p. 7539
I.2.11.1ProSe Tx tests (Chapter 6)  p. 7539
I.2.11.2ProSe Rx tests (Chapter 7)  p. 7539
I.2.11.3ProSe Performance tests (Chapter 8)  p. 7539
I.2.11.4ProSe CSI tests (Chapter 9)  p. 7539
I.2.12Tests for 4 Rx antenna ports  p. 7540
I.2.12.14 Rx antenna ports Rx tests (Chapter 7)  p. 7540
I.2.12.24 Rx antenna ports Performance tests (Chapter 8)  p. 7540
I.2.12.34 Rx antenna ports CSI tests (Chapter 9)  p. 7540
J(Normative)  Modified MPR behaviour  p. 7541
J.1Indication of modified MPR behaviour  p. 7541
K(Normative)  NB-IoT Test Frequencies  p. 7542
K.1NB-IoT Test frequencies for TRx Tests  p. 7542
K.1.1Test frequencies selection criteria 1  p. 7542
K.1.2Test frequencies selection criteria 2  p. 7542
K.1.3Test frequencies selection criteria 3  p. 7543
K.2NB-IoT Test frequencies for Demodulation Tests  p. 7543
K.2.1Test frequencies selection criteria 1  p. 7543
$Change history  p. 7544

Top