Tech-invite3GPPspaceIETFspace
959493929190898887868584838281807978777675747372717069686766656463626160595857565554535251504948474645444342414039383736353433323130292827262524232221201918171615141312111009080706050403020100
in Index   Prev   Next

RFC 4550

Internet Email to Support Diverse Service Environments (Lemonade) Profile

Pages: 23
Obsoleted by:  5550

ToP   noToC   RFC4550 - Page 1
Network Working Group                                            S. Maes
Request for Comments: 4550                                        Oracle
Category: Standards Track                                    A. Melnikov
                                                              Isode Ltd.
                                                               June 2006


         Internet Email to Support Diverse Service Environments
                           (Lemonade) Profile

Status of This Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (2006).

Abstract

This document describes a profile (a set of required extensions, restrictions, and usage modes) of the IMAP and mail submission protocols. This profile allows clients (especially those that are constrained in memory, bandwidth, processing power, or other areas) to efficiently use IMAP and Submission to access and submit mail. This includes the ability to forward received mail without needing to download and upload the mail, to optimize submission, and to efficiently resynchronize in case of loss of connectivity with the server. The Internet Email to Support Diverse Service Environments (Lemonade) profile relies upon extensions to IMAP and Mail Submission protocols; specifically, the URLAUTH and CATENATE IMAP protocol (RFC 3501) extensions and the BURL extension to the SUBMIT protocol (RFC 4409).
ToP   noToC   RFC4550 - Page 2

Table of Contents

1. Introduction ....................................................3 1.1. Conventions Used in This Document ..........................3 2. Forward without Download ........................................3 2.1. Motivations ................................................3 2.2. Message Sending Overview ...................................4 2.3. Traditional Strategy .......................................4 2.4. Step-by-Step Description ...................................5 2.4.1. Message Assembly Using IMAP CATENATE Extension ......6 2.4.2. Message Assembly Using SMTP CHUNKING and BURL Extensions ....................................10 2.5. Normative Statements Related to Forward without Download ..14 2.6. Security Considerations for "pawn-tickets" ................14 2.7. The fcc Problem ...........................................15 2.8. Registration of $Forwarded IMAP Keyword ...................15 3. Message Submission .............................................15 3.1. Pipelining ................................................16 3.2. DSN Support ...............................................16 3.3. Message Size Declaration ..................................16 3.4. Enhanced Status Code Support ..............................16 3.5. TLS .......................................................16 4. Quick Resynchronization ........................................16 5. Additional IMAP Extensions .....................................17 6. Summary of the Required IMAP and SMTP Extensions ...............17 7. Future work ....................................................18 8. Security Considerations ........................................18 8.1. Confidentiality Protection of Submitted Messages ..........19 8.2. TLS .......................................................19 9. References .....................................................20 9.1. Normative References ......................................20 9.2. Informative References ....................................21 10. Acknowledgements ..............................................21
ToP   noToC   RFC4550 - Page 3

1. Introduction

Lemonade provides enhancements to Internet email to support diverse service environments. This document describes the Lemonade profile, which includes: - "forward without download", which describes exchanges between Lemonade clients and servers to allow new email messages to be submitted incorporating content that resides on locations external to the client. - Quick mailbox resynchronization using [CONDSTORE]. - Several IMAP and SMTP extensions that save bandwidth and/or number of round-trips required to send/receive data. The organization of this document is as follows. Section 2 describes "forward without download". Section 3 describes additional SMTP extensions that must be supported by all Lemonade Submission servers. Section 4 describes IMAP quick resynchronization.

1.1. Conventions Used in This Document

In examples, "M:", "I:", and "S:" indicate lines sent by the client messaging user agent, IMAP e-mail server, and SMTP submit server, respectively. The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. All examples in this document are optimized for Lemonade use and might not represent examples of proper protocol usage for a general use Submit/IMAP client. In particular, examples assume that Lemonade Submit and IMAP servers support all Lemonade extensions described in this document, so they don't show how to deal with absence of an extension.

2. Forward without Download

2.1. Motivations

The advent of client/server email using the [RFC3501], [RFC2821], and [SUBMIT] protocols has changed what formerly were local disk operations into repetitive network data transmissions.
ToP   noToC   RFC4550 - Page 4
   Lemonade "forward without download" makes use of the [BURL] SUBMIT
   extension to enable access to external sources during the submission
   of a message.  In combination with the IMAP [URLAUTH] extension,
   inclusion of message parts or even entire messages from the IMAP mail
   store is possible with a minimal trust relationship between the IMAP
   and SMTP SUBMIT servers.

   Lemonade "forward without download" has the advantage of maintaining
   one submission protocol, and thus avoids the risk of having multiple
   parallel and possibly divergent mechanisms for submission.  The
   client can use Submit/SMTP [SUBMIT] extensions without these being
   added to IMAP.  Furthermore, by keeping the details of message
   submission in the SMTP SUBMIT server, Lemonade "forward without
   download" can work with other message retrieval protocols such as
   Post Office Protocol (POP), Network News Transfer Protocol (NNTP), or
   whatever else may be designed in the future.

2.2. Message Sending Overview

The act of sending an email message can be thought of as involving multiple steps: initiation of a new draft, draft editing, message assembly, and message submission. Initiation of a new draft and draft editing takes place in the Mail User Agent (MUA). Frequently, users choose to save more complex messages on an [RFC3501] server (via the APPEND command with the \Draft flag) for later recall by the MUA and resumption of the editing process. Message assembly is the process of producing a complete message from the final revision of the draft and external sources. At assembly time, external data is retrieved and inserted in the message. Message submission is the process of inserting the assembled message into the [RFC2821] infrastructure, typically using the [SUBMIT] protocol.

2.3. Traditional Strategy

Traditionally, messages are initiated, edited, and assembled entirely within an MUA, although drafts may be saved to an [RFC3501] server and later retrieved from the server. The completed text is then transmitted to a Message Submission Agent (MSA) for delivery.
ToP   noToC   RFC4550 - Page 5
   There is often no clear boundary between the editing and assembly
   process.  If a message is forwarded, its content is often retrieved
   immediately and inserted into the message text.  Similarly, when
   external content is inserted or attached, the content is usually
   retrieved immediately and made part of the draft.

   As a consequence, each save of a draft and subsequent retrieve of the
   draft transmits that entire (possibly large) content, as does message
   submission.

   In the past, this was not much of a problem, because drafts, external
   data, and the message submission mechanism were typically located on
   the same system as the MUA.  The most common problem was running out
   of disk quota.

2.4. Step-by-Step Description

The model distinguishes among a Mail User Agent (MUA), an IMAP4Rev1 Server ([RFC3501]), and a SMTP submit server ([SUBMIT]), as illustrated in Figure 1. +--------------------+ +--------------+ | | <------------ | | | MUA (M) | | IMAPv4Rev1 | | | | Server | | | ------------> | (Server I) | +--------------------+ +--------------+ ^ | ^ | | | | | | | | | | | | | | | | | | | | | | | | v | | +--------------+ | |----------------------> | SMTP | | | Submit | |-----------------------------| Server | | (Server S) | +--------------+ Figure 1: Lemonade "forward without download" Lemonade "forward without download" allows a Messaging User Agent to compose and forward an e-mail combining fragments that are located in an IMAP server, without having to download these fragments to the client.
ToP   noToC   RFC4550 - Page 6
   There are two ways to perform "forward without download", based on
   where the message assembly takes place.  The first uses an extended
   APPEND command [CATENATE] to edit a draft message in the message
   store and cause the message assembly on the IMAP server.  The second
   uses a succession of BURL and BDAT commands to submit and assemble
   (through concatenation) message data from the client and external
   data fetched from the provided URL.  The two subsequent sections
   provide step-by-step instructions on how "forward without download"
   is achieved.

2.4.1. Message Assembly Using IMAP CATENATE Extension

In the [BURL]/[CATENATE] variant of the Lemonade "forward without download" strategy, messages are initially composed and edited within an MUA. The [CATENATE] extension to [RFC3501] is then used to create the messages on the IMAP server by transmitting new text and assembling them. The [UIDPLUS] IMAP extension is used by the client in order to learn the Unique Identifier (UID) of the created messages. Finally, a [URLAUTH] format URL is given to a [SUBMIT] server for submission using the [BURL] extension. The flow involved to support such a use case consists of: M: {to I -- Optional} The client connects to the IMAP server, optionally starts TLS (if data confidentiality is required), authenticates, opens a mailbox ("INBOX" in the example below) and fetches body structures (See [RFC3501]). Example: M: A0051 UID FETCH 25627 (UID BODYSTRUCTURE) I: * 161 FETCH (UID 25627 BODYSTRUCTURE (("TEXT" "PLAIN" ("CHARSET" "US-ASCII") NIL NIL "7BIT" 1152 23)( "TEXT" "PLAIN" ("CHARSET" "US-ASCII" "NAME" "trip.txt") "<960723163407.20117h@washington.example.com>" "Your trip details" "BASE64" 4554 73) "MIXED")) I: A0051 OK completed M: {to I} The client invokes CATENATE (See [CATENATE] for details of the semantics and steps) -- this allows the MUA to create messages on the IMAP server using new data combined with one or more message parts already present on the IMAP server. Note that the example for this step doesn't use the LITERAL+ [LITERAL+] extension. Without LITERAL+, the new message is constructed using 3 round-trips. If LITERAL+ is used, the new message can be constructed using one round-trip.
ToP   noToC   RFC4550 - Page 7
         M: A0052 APPEND Sent FLAGS (\Seen $MDNSent)
            CATENATE (TEXT {475}
         I: + Ready for literal data
         M: Message-ID: <419399E1.6000505@caernarfon.example.org>
         M: Date: Thu, 12 Nov 2004 16:57:05 +0000
         M: From: Bob Ar <bar@example.org>
         M: MIME-Version: 1.0
         M: To: foo@example.net
         M: Subject: About our holiday trip
         M: Content-Type: multipart/mixed;
         M:     boundary="------------030308070208000400050907"
         M:
         M: --------------030308070208000400050907
         M: Content-Type: text/plain; format=flowed
         M:
         M: Our travel agent has sent the updated schedule.
         M:
         M: Cheers,
         M: Bob
         M: --------------030308070208000400050907
         M:  URL "/INBOX;UIDVALIDITY=385759045/;
            UID=25627/;Section=2.MIME" URL "/INBOX;
            UIDVALIDITY=385759045/;UID=25627/;Section=2" TEXT {44}
         I: + Ready for literal data
         M:
         M: --------------030308070208000400050907--
         M: )
         I: A0052 OK [APPENDUID 387899045 45] CATENATE Completed

      M: {to I} The client uses GENURLAUTH command to request a URLAUTH
      URL (see [URLAUTH]).

      I: {to M} The IMAP server returns a URLAUTH URL suitable for later
      retrieval with URLFETCH (see [URLAUTH] for details of the
      semantics and steps).

         M: A0054 GENURLAUTH "imap://bob.ar@example.org/Sent;
            UIDVALIDITY=387899045/;uid=45;expire=2005-10-
            28T23:59:59Z;urlauth=submit+bob.ar" INTERNAL
         I: * GENURLAUTH "imap://bob.ar@example.org/Sent;
            UIDVALIDITY=387899045/;uid=45;expire=
            2005-10-28T23:59:59Z;urlauth=submit+bob.ar:
            internal:91354a473744909de610943775f92038"
         I: A0054 OK GENURLAUTH completed

      M: {to S} The client connects to the mail submission server and
      starts a new mail transaction.  It uses BURL to let the SMTP
      submit server fetch the content of the message from the IMAP
ToP   noToC   RFC4550 - Page 8
      server.  (See [BURL] for details of the semantics and steps.)
      This allows the MUA to authorize the SMTP submit server to access
      the message composed as a result of the CATENATE step.  Note that
      the second EHLO command is required after a successful STARTTLS
      command.  Also note that there might be a third required EHLO
      command if the second EHLO response doesn't list any BURL options.
      Section 2.4.2 demonstrates this.

         S: 220 owlry.example.org ESMTP
         M: EHLO potter.example.org
         S: 250-owlry.example.com
         S: 250-8BITMIME
         S: 250-BINARYMIME
         S: 250-PIPELINING
         S: 250-BURL imap
         S: 250-CHUNKING
         S: 250-AUTH PLAIN
         S: 250-DSN
         S: 250-SIZE 10240000
         S: 250-STARTTLS
         S: 250 ENHANCEDSTATUSCODES
         M: STARTTLS
         S: 220 Ready to start TLS
         ...TLS negotiation, subsequent data is encrypted...
         M: EHLO potter.example.org
         S: 250-owlry.example.com
         S: 250-8BITMIME
         S: 250-BINARYMIME
         S: 250-PIPELINING
         S: 250-BURL imap
         S: 250-CHUNKING
         S: 250-AUTH PLAIN
         S: 250-DSN
         S: 250-SIZE 10240000
         S: 250 ENHANCEDSTATUSCODES
         M: AUTH PLAIN aGFycnkAaGFycnkAYWNjaW8=
         S: 235 2.7.0 PLAIN authentication successful.
         M: MAIL FROM:<bob.ar@example.org>
         S: 250 2.5.0 Address Ok.
         M: RCPT TO:<foo@example.net>
         S: 250 2.1.5 foo@example.net OK.
         M: BURL imap://bob.ar@example.org/Sent;UIDVALIDITY=387899045/;
            uid=45/;urlauth=submit+bar:internal:
            91354a473744909de610943775f92038 LAST
ToP   noToC   RFC4550 - Page 9
      S: {to I} The mail submission server uses URLFETCH to fetch the
      message to be sent.  (See [URLAUTH] for details of the semantics
      and steps.  The so-called "pawn-ticket" authorization mechanism
      uses a URI that contains its own authorization credentials.)

      I: {to S} Provides the message composed as a result of the
      CATENATE step.

      Mail submission server opens IMAP connection to the IMAP server:

         I: * OK [CAPABILITY IMAP4REV1 STARTTLS NAMESPACE LITERAL+
            CATENATE URLAUTH UIDPLUS CONDSTORE IDLE] imap.example.com
            IMAP server ready
         S: a000 STARTTLS
         I: a000 Start TLS negotiation now
         ...TLS negotiation, if successful - subsequent data
            is encrypted...
         S: a001 LOGIN submitserver secret
         I: a001 OK submitserver logged in
         S: a002 URLFETCH "imap://bob.ar@example.org/Sent;
            UIDVALIDITY=387899045/;uid=45/;urlauth=submit+bob.ar:
            internal:91354a473744909de610943775f92038"
         I: * URLFETCH "imap://bob.ar@example.org/Sent;
            UIDVALIDITY=387899045/;uid=45/;urlauth=submit+bob.ar:
            internal:91354a473744909de610943775f92038" {15065}
         ...message body follows...
         S: a002 OK URLFETCH completed
         I: a003 LOGOUT
         S: * BYE See you later
         S: a003 OK Logout successful

      Note that if the IMAP server doesn't send CAPABILITY response code
      in the greeting, the mail submission server must issue the
      CAPABILITY command to learn about supported IMAP extensions as
      described in RFC 3501.

      Also, if data confidentiality is not required, the mail submission
      server may omit the STARTTLS command before issuing the LOGIN
      command.

      S: {to M} Submission server assembles the complete message, and if
      the assembly succeeds, it returns OK to the MUA:

         S: 250 2.5.0 Ok.

      M: {to I} The client marks the message containing the forwarded
      attachment on the IMAP server.
ToP   noToC   RFC4550 - Page 10
         M: A0053 UID STORE 25627 +FLAGS.SILENT ($Forwarded)
         I: * 215 FETCH (UID 25627 MODSEQ (12121231000))
         I: A0053 OK STORE completed

      Note: the UID STORE command shown above will only work if the
      marked message is in the currently selected mailbox; otherwise, it
      requires a SELECT.  This command can be omitted.  The untagged
      FETCH response is due to [CONDSTORE].  The $Forwarded IMAP keyword
      is described in Section 2.8.

2.4.2. Message Assembly Using SMTP CHUNKING and BURL Extensions

In the [BURL]/[CHUNKING] variant of the Lemonade "forward without download" strategy, messages are initially composed and edited within an MUA. During submission [SUBMIT], BURL [BURL] and BDAT [CHUNKING] commands are used to create the messages from multiple parts. New body parts are supplied using BDAT commands, while existing body parts are referenced using [URLAUTH] format URLs in BURL commands. The flow involved to support such a use case consists of: M: {to I -- Optional} The client connects to the IMAP server, optionally starts TLS (if data confidentiality is required), authenticates, opens a mailbox ("INBOX" in the example below), and fetches body structures (see [RFC3501]). Example: M: A0051 UID FETCH 25627 (UID BODYSTRUCTURE) I: * 161 FETCH (UID 25627 BODYSTRUCTURE (("TEXT" "PLAIN" ("CHARSET" "US-ASCII") NIL NIL "7BIT" 1152 23)( "TEXT" "PLAIN" ("CHARSET" "US-ASCII" "NAME" "trip.txt") "<960723163407.20117h@washington.example.com>" "Your trip details" "BASE64" 4554 73) "MIXED")) I: A0051 OK completed M: {to I} The client uses GENURLAUTH command to request URLAUTH URLs (see [URLAUTH]) referencing pieces of the message to be assembled. I: {to M} The IMAP server returns URLAUTH URLs suitable for later retrieval with URLFETCH (see [URLAUTH] for details of the semantics and steps). M: A0054 GENURLAUTH "imap://bob.ar@example.org/INBOX; UIDVALIDITY=385759045/;UID=25627/;Section=2.MIME; expire=2006-10-28T23:59:59Z;urlauth=submit+bob.ar"
ToP   noToC   RFC4550 - Page 11
            INTERNAL "imap://bob.ar@example.org/INBOX;
            UIDVALIDITY=385759045/;UID=25627/;Section=2;
            expire=2006-10-28T23:59:59Z;urlauth=submit+bob.ar" INTERNAL
         I: * GENURLAUTH "imap://bob.ar@example.org/INBOX;
            UIDVALIDITY=385759045/;UID=25627/;Section=2.MIME;
            expire=2006-10-28T23:59:59Z;urlauth=submit+bob.ar:
            internal:A0DEAD473744909de610943775f9BEEF"
            "imap://bob.ar@example.org/INBOX;
            UIDVALIDITY=385759045/;UID=25627/;Section=2;
            expire=2006-10-28T23:59:59Z;urlauth=submit+bob.ar:
            internal:BEEFA0DEAD473744909de610943775f9"
         I: A0054 OK GENURLAUTH completed

      M: {to S} The client connects to the mail submission server and
      starts a new mail transaction.  It uses BURL to instruct the SMTP
      submit server to fetch from the IMAP server pieces of the message
      to be sent (see [BURL] for details of the semantics and steps).
      Note that the second EHLO command is required after a successful
      STARTTLS command.  The third EHLO command is required if and only
      if the second EHLO response doesn't list any BURL options.  See
      Section 2.4.1 for an example of submission where the third EHLO
      command/response is not present.

         S: 220 owlry.example.org ESMTP
         M: EHLO potter.example.org
         S: 250-owlry.example.com
         S: 250-8BITMIME
         S: 250-BINARYMIME
         S: 250-PIPELINING
         S: 250-BURL
         S: 250-CHUNKING
         S: 250-AUTH DIGEST-MD5
         S: 250-DSN
         S: 250-SIZE 10240000
         S: 250-STARTTLS
         S: 250 ENHANCEDSTATUSCODES
         M: STARTTLS
         S: 220 Ready to start TLS
         ...TLS negotiation, subsequent data is encrypted...
         M: EHLO potter.example.org
         S: 250-owlry.example.com
         S: 250-8BITMIME
         S: 250-BINARYMIME
         S: 250-PIPELINING
         S: 250-BURL
         S: 250-CHUNKING
         S: 250-AUTH DIGEST-MD5 CRAM-MD5 PLAIN EXTERNAL
         S: 250-DSN
ToP   noToC   RFC4550 - Page 12
         S: 250-SIZE 10240000
         S: 250 ENHANCEDSTATUSCODES
         M: AUTH PLAIN aGFycnkAaGFycnkAYWNjaW8=
         S: 235 2.7.0 PLAIN authentication successful.
         M: EHLO potter.example.org
         S: 250-owlry.example.com
         S: 250-8BITMIME
         S: 250-BINARYMIME
         S: 250-PIPELINING
         S: 250-BURL imap imap://imap.example.org
         S: 250-CHUNKING
         S: 250-AUTH DIGEST-MD5 CRAM-MD5 PLAIN EXTERNAL
         S: 250-DSN
         S: 250-SIZE 10240000
         S: 250 ENHANCEDSTATUSCODES
         M: MAIL FROM:<bob.ar@example.org> BODY=BINARY
         S: 250 2.5.0 Address Ok.
         M: RCPT TO:<foo@example.net>
         S: 250 2.1.5 foo@example.net OK.
         M: BDAT 475
         M: Message-ID: <419399E1.6000505@caernarfon.example.org>
         M: Date: Thu, 12 Nov 2004 16:57:05 +0000
         M: From: Bob Ar <bar@example.org>
         M: MIME-Version: 1.0
         M: To: foo@example.net
         M: Subject: About our holiday trip
         M: Content-Type: multipart/mixed;
         M:     boundary="------------030308070208000400050907"
         M:
         M: --------------030308070208000400050907
         M: Content-Type: text/plain; format=flowed
         M:
         M: Our travel agent has sent the updated schedule.
         M:
         M: Cheers,
         M: Bob
         M: --------------030308070208000400050907
         S: 250 2.5.0 OK
         M: BURL imap://bob.ar@example.org/INBOX;
            UIDVALIDITY=385759045/;UID=25627/;Section=2.MIME;
            expire=2006-10-28T23:59:59Z;urlauth=submit+bob.ar:
            internal:A0DEAD473744909de610943775f9BEEF
         S: 250 2.5.0 OK
         M: BURL imap://bob.ar@example.org/INBOX;
            UIDVALIDITY=385759045/;UID=25627/;Section=2;
            expire=2006-10-28T23:59:59Z;urlauth=submit+bob.ar:
            internal:BEEFA0DEAD473744909de610943775f9
         S: 250 2.5.0 OK
ToP   noToC   RFC4550 - Page 13
         M: BDAT 44 LAST
         M:
         M: --------------030308070208000400050907--

      S: {to I} The mail submission server uses URLFETCH to fetch the
      pieces of the message to be sent (see [URLAUTH] for details of the
      semantics and steps).  The so-called "pawn-ticket" authorization
      mechanism uses a URI that contains its own authorization
      credentials.

      I: {to S} Returns the requested body parts.

      Mail submission server opens IMAP connection to the IMAP server:

         I: * OK [CAPABILITY IMAP4REV1 STARTTLS NAMESPACE LITERAL+
            CATENATE URLAUTH UIDPLUS CONDSTORE IDLE] imap.example.com
            IMAP server ready
         S: a001 LOGIN submitserver secret
         I: a001 OK submitserver logged in
         S: a002 URLFETCH "imap://bob.ar@example.org/INBOX;
            UIDVALIDITY=385759045/;UID=25627/;Section=2.MIME;
            expire=2006-10-28T23:59:59Z;urlauth=submit+bob.ar:
            internal:A0DEAD473744909de610943775f9BEEF" "imap://
            bob.ar@example.org/INBOX;
            UIDVALIDITY=385759045/;UID=25627/;Section=2;
            expire=2006-10-28T23:59:59Z;urlauth=submit+bob.ar:
            internal:BEEFA0DEAD473744909de610943775f9"
         I: * URLFETCH "imap://bob.ar@example.org/INBOX;
            UIDVALIDITY=385759045/;UID=25627/;Section=2.MIME;
            expire=2006-10-28T23:59:59Z;urlauth=submit+bob.ar:
            internal:A0DEAD473744909de610943775f9BEEF" {84}
         ...message section follows...
             "imap://bob.ar@example.org/INBOX;
            UIDVALIDITY=385759045/;UID=25627/;Section=2;
            expire=2006-10-28T23:59:59Z;urlauth=submit+bob.ar:
            internal:BEEFA0DEAD473744909de610943775f9" {15065}
         ...message section follows...
         S: a002 OK URLFETCH completed
         I: a003 LOGOUT
         S: * BYE See you later
         S: a003 OK Logout successful

      Note that if the IMAP server doesn't send CAPABILITY response code
      in the greeting, the mail submission server must issue the
      CAPABILITY command to learn about supported IMAP extensions as
      described in RFC 3501.
ToP   noToC   RFC4550 - Page 14
      Also, if data confidentiality is required, the mail submission
      server should start TLS before issuing the LOGIN command.

      S: {to M} Submission server assembles the complete message, and if
      the assembly succeeds, it acknowledges acceptance of the message
      by sending 250 response to the last BDAT command:

         S: 250 2.5.0 Ok, message accepted.

      M: {to I} The client marks the message containing the forwarded
      attachment on the IMAP server.

         M: A0053 UID STORE 25627 +FLAGS.SILENT ($Forwarded)
         I: * 215 FETCH (UID 25627 MODSEQ (12121231000))
         I: A0053 OK STORE completed

      Note: the UID STORE command shown above will only work if the
      marked message is in the currently selected mailbox; otherwise, it
      requires a SELECT.  This command can be omitted.  The untagged
      FETCH response is due to [CONDSTORE].  The $Forwarded IMAP keyword
      is described in Section 2.8.

2.5. Normative Statements Related to Forward without Download

Lemonade-compliant IMAP servers MUST support IMAP4Rev1 [RFC3501], CATENATE [CATENATE], UIDPLUS [UIDPLUS], and URLAUTH [URLAUTH]. This support MUST be declared via CAPABILITY [RFC3501]. Lemonade-compliant submit servers MUST support BURL [BURL], 8BITMIME [8BITMIME], BINARYMIME [CHUNKING], and CHUNKING [CHUNKING]. This support MUST be declared via EHLO [RFC2821]. BURL MUST support URLAUTH type URLs [URLAUTH], and thus MUST advertise the "imap" option following the BURL EHLO keyword (see [BURL] for more details). Additional normative statements are provided in other sections.

2.6. Security Considerations for "pawn-tickets"

The so-called "pawn-ticket" authorization mechanism uses a URI, which contains its own authorization credentials using [URLAUTH]. The advantage of this mechanism is that the SMTP submit [SUBMIT] server cannot access any data on the [RFC3501] server without a "pawn- ticket" created by the client. The "pawn-ticket" grants access only to the specific data that the SMTP submit [SUBMIT] server is authorized to access, can be revoked by the client, and can have a time-limited validity.
ToP   noToC   RFC4550 - Page 15

2.7. The fcc Problem

The "fcc problem" refers to delivering a copy of a message to a "file carbon copy" recipient. By far, the most common case of fcc is a client leaving a copy of outgoing mail in a "Sent Mail" or "Outbox" mailbox. In the traditional strategy, the MUA duplicates the effort spent in transmitting to the MSA by writing the message to the fcc destination in a separate step. This may be a write to a local disk file or an APPEND to a mailbox on an IMAP server. The latter is one of the "repetitive network data transmissions" that represents the "problem" aspect of the "fcc problem". The [CATENATE] extension to [RFC3501] can be used to address the fcc problem. The final message is constructed in the mailbox designed for outgoing mail. Note that the [CATENATE] extension can only create a single message and only on the server that stages the outgoing message for submission. Additional copies of the message can be created on the same server using one or more COPY commands.

2.8. Registration of $Forwarded IMAP Keyword

The $Forwarded IMAP keyword is used by several IMAP clients to specify that the message was resent to another email address, embedded within or attached to a new message. A mail client sets this keyword when it successfully forwards the message to another email address. Typical usage of this keyword is to show a different (or additional) icon for a message that has been forwarded. Once set, the flag SHOULD NOT be cleared. Lemonade-compliant servers MUST be able to store the $Forwarded keyword. They MUST preserve it on the COPY operation. The servers MUST support the SEARCH KEYWORD $Forwarded.

3. Message Submission

Lemonade-compliant mail submission servers are expected to implement the following set of SMTP extensions to make message submission efficient. Lemonade clients should take advantage of these features.
ToP   noToC   RFC4550 - Page 16

3.1. Pipelining

Mobile clients regularly use networks with a relatively high latency. Avoidance of round-trips within a transaction has a great advantage for reduction in both bandwidth and total transaction time. For this reason, Lemonade-compliant mail submission servers MUST support the SMTP Service Extensions for Command Pipelining [RFC2920]. Clients SHOULD pipeline SMTP commands when possible.

3.2. DSN Support

Lemonade-compliant mail submission servers MUST support SMTP service extensions for delivery status notifications [RFC3461].

3.3. Message Size Declaration

Lemonade-compliant mail submission servers MUST support the SMTP Service Extension for Message Size Declaration [RFC1870]. Lemonade-compliant mail submission servers MUST "expand" all BURL parts before enforcing a message size limit. A Lemonade-compliant client SHOULD use message size declaration. In particular, it MUST NOT send a message to a mail submission server, if the client knows that the message exceeds the maximal message size advertised by the submission server.

3.4. Enhanced Status Code Support

Lemonade-compliant mail submission servers MUST support SMTP Service Extension for Returning Enhanced Error Codes [RFC2034].

3.5. TLS

Lemonade-compliant mail submission servers MUST support SMTP Service Extension for Secure SMTP over TLS [SMTP-TLS].

4. Quick Resynchronization

Lemonade-compliant IMAP servers MUST support the CONDSTORE [CONDSTORE] extension. It allows a client to quickly resynchronize any mailbox by asking the server to return all flag changes that have occurred since the last known mailbox synchronization mark. [IMAP-DISC] shows how to perform quick mailbox resynchronization.
ToP   noToC   RFC4550 - Page 17

5. Additional IMAP Extensions

Lemonade-compliant IMAP servers MUST support the NAMESPACE [NAMESPACE] extension. The extension allows clients to discover shared mailboxes and mailboxes belonging to other users. Lemonade-compliant IMAP servers MUST support the LITERAL+ [LITERAL+] extension. The extension allows clients to save a round-trip each time a non-synchronizing literal is sent. Lemonade-compliant IMAP servers MUST support the IDLE [IDLE] extension. The extension allows clients to receive instant notifications about changes in the selected mailbox, without needing to poll for changes. Lemonade-compliant IMAP servers MUST support IMAP over TLS [RFC3501] as required by RFC 3501.

6. Summary of the Required IMAP and SMTP Extensions

-----------------------------------------------------| | Name of SMTP extension | Comment | |-------------------------|--------------------------| | PIPELINING | Section 3.1 | |-------------------------|--------------------------| | DSN | Section 3.2 | |-------------------------|--------------------------| | SIZE | Section 3.3 | |-------------------------|--------------------------| | ENHANCEDSTATUSCODES | Section 3.4 | |-------------------------|--------------------------| | STARTTLS | Section 3.5 | |-------------------------|--------------------------| | BURL | Forward without download,| | | Section 2 | |-------------------------|--------------------------| | URLAUTH support in BURL | Section 2.5 | |-------------------------|--------------------------| | CHUNKING, | Section 2.5 | | BINARYMIME | Section 2.5 | |-------------------------|--------------------------| | 8BITMIME, | Required by BURL | |-------------------------|--------------------------| | AUTH | Required by Submission, | | | See [SMTPAUTH]. | |-------------------------|--------------------------|
ToP   noToC   RFC4550 - Page 18
      -----------------------------------------------------|
      |  Name of IMAP extension |            Comment       |
      |        or feature       |                          |
      |-------------------------|--------------------------|
      |        NAMESPACE        |       Section 5          |
      |-------------------------|--------------------------|
      |        CONDSTORE        |       Section 4          |
      |-------------------------|--------------------------|
      |        STARTTLS         |Required by IMAP (RFC3501)|
      |-------------------------|--------------------------|
      |        URLAUTH,         | Forward without download,|
      |        CATENATE,        |        Section 2         |
      |        UIDPLUS          |                          |
      |-------------------------|--------------------------|
      |        LITERAL+         |       Section 5          |
      |-------------------------|--------------------------|
      |          IDLE           |       Section 5          |
      |-------------------------|--------------------------|
      | $Forwarded IMAP keyword |       Section 2.8        |
      |-------------------------|--------------------------|

7. Future work

The Lemonade Working Group is looking into additional issues related to usage of email by mobile devices, possibly including: - Media conversion (static and possibly streamed) - Transport optimization for low or costly bandwidth and less reliable mobile networks (e.g., quick reconnect) - Server to client notifications, possibly outside of the traditional IMAP band - Dealing with firewall and intermediaries - Compression and other bandwidth optimization - Filtering - Other considerations for mobile clients

8. Security Considerations

Security considerations on Lemonade "forward without download" are discussed throughout Section 2. Additional security considerations can be found in [RFC3501] and other documents describing other SMTP and IMAP extensions comprising the Lemonade profile. Note that the mandatory-to-implement authentication mechanism for SMTP submission is described in [SUBMIT]. The mandatory-to-implement authentication mechanism for IMAP is described in [RFC3501].
ToP   noToC   RFC4550 - Page 19

8.1. Confidentiality Protection of Submitted Messages

When clients submit new messages, link protection such as TLS guards against an eavesdropper seeing the contents of the submitted message. It's worth noting, however, that even if TLS is not used, the security risks are no worse if BURL is used to reference the text than if the text is submitted directly. If BURL is not used, an eavesdropper gains access to the full text of the message. If BURL is used, the eavesdropper may or may not be able to gain such access, depending on the form of BURL used. For example, some forms restrict use of the URL to an entity authorized as a submission server or a specific user.

8.2. TLS

When Lemonade clients use the BURL extension to mail submission, which requires sending a URLAUTH token to the mail submission server, such a token should be protected from interception to avoid a replay attack that may disclose the contents of the message to an attacker. TLS-based encryption of the mail submission path will provide protection against this attack. Lemonade clients SHOULD use TLS-protected IMAP and mail submission channels when using BURL-based message submission to protect the URLAUTH token from interception. Lemonade-compliant mail submission servers SHOULD use TLS-protected IMAP connections when fetching message content using the URLAUTH token provided by the Lemonade client. When a client uses SMTP STARTTLS to send a BURL command that references non-public information, there is a user expectation that the entire message content will be treated confidentially. To meet this expectation, the message submission server should use STARTTLS or a mechanism providing equivalent data confidentiality when fetching the content referenced by that URL.
ToP   noToC   RFC4550 - Page 20

9. References

9.1. Normative References

[BURL] Newman, C. "Message Submission BURL Extension", RFC 4468, May 2006. [8BITMIME] Klensin, J., Freed, N., Rose, M., Stefferud, E., and D. Crocker, "SMTP Service Extension for 8bit-MIMEtransport", RFC 1652, July 1994. [CHUNKING] Vaudreuil, G., "SMTP Service Extensions for Transmission of Large and Binary MIME Messages", RFC 3030, December 2000. [CATENATE] Resnick, P., "Internet Message Access Protocol (IMAP) CATENATE Extension", RFC 4469, April 2006. [UIDPLUS] Crispin, M., "Internet Message Access Protocol (IMAP) - UIDPLUS extension", RFC 4315, December 2005. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2920] Freed, N., "SMTP Service Extension for Command Pipelining", STD 60, RFC 2920, September 2000. [RFC1870] Klensin, J., Freed, N., and K. Moore, "SMTP Service Extension for Message Size Declaration", STD 10, RFC 1870, November 1995. [SUBMIT] Gellens, R. and J. Klensin, "Message Submission for Mail", RFC 4409, April 2006. [SMTP-TLS] Hoffman, P., "SMTP Service Extension for Secure SMTP over Transport Layer Security", RFC 3207, February 2002. [RFC2821] Klensin, J., "Simple Mail Transfer Protocol", RFC 2821, April 2001. [RFC3501] Crispin, M., "INTERNET MESSAGE ACCESS PROTOCOL - VERSION 4rev1", RFC 3501, March 2003. [RFC3461] Moore, K., "Simple Mail Transfer Protocol (SMTP) Service Extension for Delivery Status Notifications (DSNs)", RFC 3461, January 2003.
ToP   noToC   RFC4550 - Page 21
   [URLAUTH]   Crispin, M., "Internet Message Access Protocol (IMAP) -
               URLAUTH Extension", RFC 4467, May 2006.

   [RFC2034]   Freed, N., "SMTP Service Extension for Returning Enhanced
               Error Codes", RFC 2034, October 1996.

   [NAMESPACE] Gahrns, M. and C. Newman, "IMAP4 Namespace", RFC 2342,
               May 1998.

   [SMTPAUTH]  Myers, J., "SMTP Service Extension for Authentication",
               RFC 2554, March 1999.

   [LITERAL+]  Myers, J., "IMAP4 non-synchronizing literals", RFC 2088,
               January 1997.

   [CONDSTORE] Melnikov, A. and S. Hole, "IMAP Extension for Conditional
               STORE Operation or Quick Flag Changes Resynchronization",
               RFC 4551, June 2006.

   [IDLE]      Leiba, B., "IMAP4 IDLE command", RFC 2177, June 1997.

9.2. Informative References

[IMAP-DISC] Melnikov, A., "Synchronization operations for disconnected IMAP4 clients", Work in Progress, October 2004.

10. Acknowledgements

This document is a product of Lemonade WG. The editors thank the Lemonade WG members that contributed comments and corrections; in particular: Randy Gellens, Dave Cridland, and Greg Vaudreuil. This document borrows some text from "Message Submission" (February 2004) by Mark Crispin, as well as from the trio [BURL], [CATENATE], and [URLAUTH].
ToP   noToC   RFC4550 - Page 22

Authors' Addresses

Stephane H. Maes Oracle Corporation 500 Oracle Parkway M/S 4op634 Redwood Shores, CA 94065 USA Phone: +1-650-607-6296 EMail: stephane.maes@oracle.com Alexey Melnikov Isode Limited 5 Castle Business Village 36 Station Road Hampton, Middlesex TW12 2BX UK EMail: Alexey.melnikov@isode.com
ToP   noToC   RFC4550 - Page 23
Full Copyright Statement

   Copyright (C) The Internet Society (2006).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
   ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
   INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
   INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at
   ietf-ipr@ietf.org.

Acknowledgement

   Funding for the RFC Editor function is provided by the IETF
   Administrative Support Activity (IASA).