RFC 9348
A YANG Data Model for IP Traffic Flow Security
Pages: ~25
IETF/sec/ipsecme/draft-ietf-ipsecme-yang-iptfs-11
Proposed Standard
A YANG Data Model for IP Traffic Flow Security
Abstract
This document describes a YANG module for the management of IP Traffic Flow Security (IP-TFS) additions to Internet Key Exchange Protocol version 2 (IKEv2) and IPsec.
Status of This Memo
This is an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Further information on Internet Standards is available in Section 2 of RFC 7841.
Information about the current status of this document, any errata, and how to provide feedback on it may be obtained at https://www.rfc-editor.org/info/rfc9348 .
Copyright Notice
Copyright (c) 2023 IETF Trust and the persons identified as the document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info ) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License.
1. Introduction
This document defines a YANG module [RFC 7950] for the management of the IP Traffic Flow Security (IP-TFS) extensions defined in [RFC 9347]. IP-TFS provides enhancements to an IPsec tunnel Security Association (SA) to provide improved traffic confidentiality. Traffic confidentiality reduces the ability of traffic analysis to determine identity and correlate observable traffic patterns. IP-TFS offers efficiency when aggregating traffic in fixed-size IPsec tunnel packets.
The YANG data model in this document conforms to the Network Management Datastore Architecture (NMDA) defined in [RFC 8342].
The published YANG modules for IPsec are defined in [RFC 9061]. This document uses these models as a general IPsec model that is augmented for IP-TFS. The models in [RFC 9061] provide for both an IKE and an IKE-less model.
2. Overview
This document defines configuration and operational parameters of IP Traffic Flow Security (IP-TFS). IP-TFS, defined in [RFC 9347], defines a security association for tunnel mode IPsec with characteristics that improve traffic confidentiality and reduce bandwidth efficiency loss. These documents assume familiarity with the IPsec concepts described in [RFC 4301].
IP-TFS uses tunnel mode to improve confidentiality by hiding inner packet identifiable information, packet size, and packet timing. IP-TFS provides a general capability allowing aggregation of multiple packets in uniform-size outer tunnel IPsec packets. It maintains the outer packet size by utilizing combinations of aggregating, padding, and fragmenting inner packets to fill out the IPsec outer tunnel packet. Padding is used to fill the packet when no data is available to send.
This document specifies an extensible configuration model for IP-TFS. This version utilizes the capabilities of IP-TFS to configure fixed-size IP-TFS packets that are transmitted at a constant rate. This model is structured to allow for different types of operation through future augmentation.
The IP-TFS YANG module augments the IPsec YANG module from [RFC 9061]. IP-TFS makes use of IPsec tunnel mode and adds a small number of configuration items to IPsec tunnel mode. As defined in [RFC 9347], any SA configured to use IP-TFS supports only IP-TFS packets, i.e., no mixed IPsec modes.
The behavior for IP-TFS is controlled by the source. The self-describing format of an IP-TFS packet allows a sending side to adjust the packet size and timing independently from any receiver. Both directions are also independent, e.g., IP-TFS may be run only in one direction. This means that counters, which are created here for both directions, may be 0 or not updated in the case of an SA that uses IP-TFS only in on direction.
Cases where IP-TFS statistics are active for one direction:
- SA one direction - IP-TFS enabled
- SA both directions - IP-TFS only enabled in one direction
- SA both directions - IP-TFS enable for both directions
- Congestion Control:
- A congestion control setting to allow IP-TFS to reduce the packet rate when congestion is detected.
- Fixed-Rate Configuration:
- The IP-TFS tunnel rate can be configured by takinginto account either layer 2 overhead or layer 3 overhead. Layer 3 overheadis the IP data rate, and layer 2 overhead is the rate of bits on the link. The combination of packet size and rate determines thenominal maximum bandwidth and the transmission interval when fixed-size packetsare used.
- User Packet Fragmentation Control:
- While fragmentation is recommendedfor improved efficiency, a configuration is provided if users wish to observethe effect of no fragmentation on their data flows.
3. YANG Management
3.1. YANG Tree
The following is the YANG tree diagram [RFC 8340] for the IP-TFS extensions.
module: ietf-ipsec-iptfs
augment /nsfike:ipsec-ike/nsfike:conn-entry/nsfike:spd
/nsfike:spd-entry/nsfike:ipsec-policy-config
/nsfike:processing-info/nsfike:ipsec-sa-cfg:
+--rw traffic-flow-security
+--rw congestion-control? boolean
+--rw packet-size
| +--rw use-path-mtu-discovery? boolean
| +--rw outer-packet-size? uint16
+--rw (tunnel-rate)?
| +--:(l2-fixed-rate)
| | +--rw l2-fixed-rate? yang:gauge64
| +--:(l3-fixed-rate)
| +--rw l3-fixed-rate? yang:gauge64
+--rw dont-fragment? boolean
+--rw max-aggregation-time? decimal64
+--rw window-size? uint16
+--rw send-immediately? boolean
+--rw lost-packet-timer-interval? decimal64
augment /nsfike:ipsec-ike/nsfike:conn-entry/nsfike:child-sa-info:
+--ro traffic-flow-security
+--ro congestion-control? boolean
+--ro packet-size
| +--ro use-path-mtu-discovery? boolean
| +--ro outer-packet-size? uint16
+--ro (tunnel-rate)?
| +--:(l2-fixed-rate)
| | +--ro l2-fixed-rate? yang:gauge64
| +--:(l3-fixed-rate)
| +--ro l3-fixed-rate? yang:gauge64
+--ro dont-fragment? boolean
+--ro max-aggregation-time? decimal64
+--ro window-size? uint16
+--ro send-immediately? boolean
+--ro lost-packet-timer-interval? decimal64
augment /nsfikels:ipsec-ikeless/nsfikels:spd/nsfikels:spd-entry
/nsfikels:ipsec-policy-config/nsfikels:processing-info
/nsfikels:ipsec-sa-cfg:
+--rw traffic-flow-security
+--rw congestion-control? boolean
+--rw packet-size
| +--rw use-path-mtu-discovery? boolean
| +--rw outer-packet-size? uint16
+--rw (tunnel-rate)?
| +--:(l2-fixed-rate)
| | +--rw l2-fixed-rate? yang:gauge64
| +--:(l3-fixed-rate)
| +--rw l3-fixed-rate? yang:gauge64
+--rw dont-fragment? boolean
+--rw max-aggregation-time? decimal64
+--rw window-size? uint16
+--rw send-immediately? boolean
+--rw lost-packet-timer-interval? decimal64
augment /nsfikels:ipsec-ikeless/nsfikels:sad/nsfikels:sad-entry:
+--ro traffic-flow-security
+--ro congestion-control? boolean
+--ro packet-size
| +--ro use-path-mtu-discovery? boolean
| +--ro outer-packet-size? uint16
+--ro (tunnel-rate)?
| +--:(l2-fixed-rate)
| | +--ro l2-fixed-rate? yang:gauge64
| +--:(l3-fixed-rate)
| +--ro l3-fixed-rate? yang:gauge64
+--ro dont-fragment? boolean
+--ro max-aggregation-time? decimal64
+--ro window-size? uint16
+--ro send-immediately? boolean
+--ro lost-packet-timer-interval? decimal64
augment /nsfike:ipsec-ike/nsfike:conn-entry/nsfike:child-sa-info:
+--ro ipsec-stats {ipsec-stats}?
| +--ro tx-pkts? yang:counter64
| +--ro tx-octets? yang:counter64
| +--ro tx-drop-pkts? yang:counter64
| +--ro rx-pkts? yang:counter64
| +--ro rx-octets? yang:counter64
| +--ro rx-drop-pkts? yang:counter64
+--ro iptfs-inner-pkt-stats {iptfs-stats}?
| +--ro tx-pkts? yang:counter64
| +--ro tx-octets? yang:counter64
| +--ro rx-pkts? yang:counter64
| +--ro rx-octets? yang:counter64
| +--ro rx-incomplete-pkts? yang:counter64
+--ro iptfs-outer-pkt-stats {iptfs-stats}?
+--ro tx-all-pad-pkts? yang:counter64
+--ro tx-all-pad-octets? yang:counter64
+--ro tx-extra-pad-pkts? yang:counter64
+--ro tx-extra-pad-octets? yang:counter64
+--ro rx-all-pad-pkts? yang:counter64
+--ro rx-all-pad-octets? yang:counter64
+--ro rx-extra-pad-pkts? yang:counter64
+--ro rx-extra-pad-octets? yang:counter64
+--ro rx-errored-pkts? yang:counter64
+--ro rx-missed-pkts? yang:counter64
augment /nsfikels:ipsec-ikeless/nsfikels:sad/nsfikels:sad-entry:
+--ro ipsec-stats {ipsec-stats}?
| +--ro tx-pkts? yang:counter64
| +--ro tx-octets? yang:counter64
| +--ro tx-drop-pkts? yang:counter64
| +--ro rx-pkts? yang:counter64
| +--ro rx-octets? yang:counter64
| +--ro rx-drop-pkts? yang:counter64
+--ro iptfs-inner-pkt-stats {iptfs-stats}?
| +--ro tx-pkts? yang:counter64
| +--ro tx-octets? yang:counter64
| +--ro rx-pkts? yang:counter64
| +--ro rx-octets? yang:counter64
| +--ro rx-incomplete-pkts? yang:counter64
+--ro iptfs-outer-pkt-stats {iptfs-stats}?
+--ro tx-all-pad-pkts? yang:counter64
+--ro tx-all-pad-octets? yang:counter64
+--ro tx-extra-pad-pkts? yang:counter64
+--ro tx-extra-pad-octets? yang:counter64
+--ro rx-all-pad-pkts? yang:counter64
+--ro rx-all-pad-octets? yang:counter64
+--ro rx-extra-pad-pkts? yang:counter64
+--ro rx-extra-pad-octets? yang:counter64
+--ro rx-errored-pkts? yang:counter64
+--ro rx-missed-pkts? yang:counter64
3.2. YANG Module
The following is the YANG module for managing the IP-TFS extensions. The model contains references to [RFC 9347] and [RFC 5348].
module ietf-ipsec-iptfs {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-ipsec-iptfs";
prefix iptfs;
import ietf-i2nsf-ike {
prefix nsfike;
reference
"RFC 9061: A YANG Data Model for IPsec Flow Protection Based on
Software-Defined Networking (SDN), Section 5.2";
}
import ietf-i2nsf-ikeless {
prefix nsfikels;
reference
"RFC 9061: A YANG Data Model for IPsec Flow Protection Based on
Software-Defined Networking (SDN), Section 5.3";
}
import ietf-yang-types {
prefix yang;
reference
"RFC 6991: Common YANG Data Types";
}
organization
"IETF IPSECME Working Group (IPSECME)";
contact
"WG Web: <https://datatracker.ietf.org/wg/ipsecme/>
WG List: <mailto:ipsecme@ietf.org>
Author: Don Fedyk
<mailto:dfedyk@labn.net>
Author: Christian Hopps
<mailto:chopps@chopps.org>";
description
"This module defines the configuration and operational state for
managing the IP Traffic Flow Security functionality (RFC 9348).
Copyright (c) 2023 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
to the license terms contained in, the Revised BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(https://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC 9348; see
the RFC itself for full legal notices.";
revision 2023-01-31 {
description
"Initial revision";
reference
"RFC 9348: A YANG Data Model for IP Traffic Flow Security";
}
feature ipsec-stats {
description
"This feature indicates the device supports
per-SA IPsec statistics.";
}
feature iptfs-stats {
description
"This feature indicates the device supports
per-SA IP Traffic Flow Security statistics.";
}
/*--------------------*/
/* groupings */
/*--------------------*/
grouping ipsec-tx-stat-grouping {
description
"IPsec outbound statistics";
leaf tx-pkts {
type yang:counter64;
config false;
description
"Outbound Packet count";
}
leaf tx-octets {
type yang:counter64;
config false;
description
"Outbound Packet bytes";
}
leaf tx-drop-pkts {
type yang:counter64;
config false;
description
"Outbound dropped packets count";
}
}
grouping ipsec-rx-stat-grouping {
description
"IPsec inbound statistics";
leaf rx-pkts {
type yang:counter64;
config false;
description
"Inbound Packet count";
}
leaf rx-octets {
type yang:counter64;
config false;
description
"Inbound Packet bytes";
}
leaf rx-drop-pkts {
type yang:counter64;
config false;
description
"Inbound dropped packets count";
}
}
grouping iptfs-inner-tx-stat-grouping {
description
"IP-TFS outbound inner packet statistics";
leaf tx-pkts {
type yang:counter64;
config false;
description
"Total number of IP-TFS inner packets sent. This
count is whole packets only. A fragmented packet
counts as one packet.";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS)";
}
leaf tx-octets {
type yang:counter64;
config false;
description
"Total number of IP-TFS inner octets sent. This is
inner packet octets only. It does not count padding.";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS)";
}
}
grouping iptfs-outer-tx-stat-grouping {
description
"IP-TFS outbound inner packet statistics";
leaf tx-all-pad-pkts {
type yang:counter64;
config false;
description
"Total number of transmitted IP-TFS packets that
were all padding with no inner packet data.";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS), Section 2.2.3";
}
leaf tx-all-pad-octets {
type yang:counter64;
config false;
description
"Total number transmitted octets of padding added to
IP-TFS packets with no inner packet data.";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS), Section 2.2.3";
}
leaf tx-extra-pad-pkts {
type yang:counter64;
config false;
description
"Total number of transmitted outer IP-TFS packets
that included some padding.";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS), Section 2.2.3.1";
}
leaf tx-extra-pad-octets {
type yang:counter64;
config false;
description
"Total number of transmitted octets of padding added
to outer IP-TFS packets with data.";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS), Section 2.2.3.1";
}
}
grouping iptfs-inner-rx-stat-grouping {
description
"IP-TFS inner packet inbound statistics";
leaf rx-pkts {
type yang:counter64;
config false;
description
"Total number of IP-TFS inner packets received.";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS), Section 2.2";
}
leaf rx-octets {
type yang:counter64;
config false;
description
"Total number of IP-TFS inner octets received. It does
not include padding or overhead.";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS), Section 2.2";
}
leaf rx-incomplete-pkts {
type yang:counter64;
config false;
description
"Total number of IP-TFS inner packets that were
incomplete. Usually this is due to fragments that are
not received. Also, this may be due to misordering or
errors in received outer packets.";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS)";
}
}
grouping iptfs-outer-rx-stat-grouping {
description
"IP-TFS outer packet inbound statistics";
leaf rx-all-pad-pkts {
type yang:counter64;
config false;
description
"Total number of received IP-TFS packets that were
all padding with no inner packet data.";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS), Section 2.2.3";
}
leaf rx-all-pad-octets {
type yang:counter64;
config false;
description
"Total number of received octets of padding added to
IP-TFS packets with no inner packet data.";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS), Section 2.2.3";
}
leaf rx-extra-pad-pkts {
type yang:counter64;
config false;
description
"Total number of received outer IP-TFS packets that
included some padding.";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS), Section 2.2.3.1";
}
leaf rx-extra-pad-octets {
type yang:counter64;
config false;
description
"Total number of received octets of padding added to
outer IP-TFS packets with data.";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS), Section 2.2.3.1";
}
leaf rx-errored-pkts {
type yang:counter64;
config false;
description
"Total number of IP-TFS outer packets dropped due to
errors.";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS)";
}
leaf rx-missed-pkts {
type yang:counter64;
config false;
description
"Total number of IP-TFS outer packets missing,
indicated by a missing sequence number.";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS)";
}
}
grouping iptfs-config {
description
"This is the grouping for IP-TFS configuration.";
container traffic-flow-security {
description
"Configure the IPsec TFS in the Security
Association Database (SAD).";
leaf congestion-control {
type boolean;
default "true";
description
"When set to true, the default, this enables the
congestion control on-the-wire exchange of data that is
required by congestion control algorithms, as defined by
RFC 5348. When set to false, IP-TFS sends fixed-size
packets over an IP-TFS tunnel at a constant rate.";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS), Section 2.4.2;
RFC 5348: TCP Friendly Rate Control (TFRC): Protocol
Specification";
}
container packet-size {
description
"Packet size is either auto-discovered or manually
configured.";
leaf use-path-mtu-discovery {
type boolean;
default "true";
description
"Utilize path MTU discovery to determine maximum
IP-TFS packet size. If the packet size is explicitly
configured, then it will only be adjusted downward if
use-path-mtu-discovery is set.";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS), Section 4.2";
}
leaf outer-packet-size {
type uint16;
units "bytes";
description
"On transmission, the size of the outer encapsulating
tunnel packet (i.e., the IP packet containing
Encapsulating Security Payload (ESP)).";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS), Section 4.2";
}
}
choice tunnel-rate {
description
"The TFS bit rate may be specified at layer 2 wire
rate or layer 3 packet rate.";
leaf l2-fixed-rate {
type yang:gauge64;
units "bits/second";
description
"On transmission, target bandwidth/bit rate in
bits/second for IP-TFS tunnel. This fixed rate is the
nominal timing for the fixed-size packet. If
congestion control is enabled, the rate may be
adjusted down (or up if unset).";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS), Section 4.1";
}
leaf l3-fixed-rate {
type yang:gauge64;
units "bits/second";
description
"On transmission, target bandwidth/bit rate in
bits/second for IP-TFS tunnel. This fixed rate is the
nominal timing for the fixed-size packet. If
congestion control is enabled, the rate may be
adjusted down (or up if unset).";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS), Section 4.1";
}
}
leaf dont-fragment {
type boolean;
default "false";
description
"On transmission, disable packet fragmentation across
consecutive IP-TFS tunnel packets; inner packets larger
than what can be transmitted in outer packets will be
dropped.";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS), Section 2.2.4 and
6.1.4";
}
leaf max-aggregation-time {
type decimal64 {
fraction-digits 6;
}
units "milliseconds";
description
"On transmission, maximum aggregation time is the
maximum length of time a received inner packet can be
held prior to transmission in the IP-TFS tunnel. Inner
packets that would be held longer than this time, based
on the current tunnel configuration, will be dropped
rather than be queued for transmission. Maximum
aggregation time is configurable in milliseconds or
fractional milliseconds down to 1 nanosecond.";
}
leaf window-size {
type uint16 {
range "0..65535";
}
description
"On reception, the maximum number of out-of-order
packets that will be reordered by an IP-TFS receiver
while performing the reordering operation. The value 0
disables any reordering.";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS), Section 2.2.3";
}
leaf send-immediately {
type boolean;
default "false";
description
"On reception, send inner packets as soon as possible; do
not wait for lost or misordered outer packets.
Selecting this option reduces the inner (user) packet
delay but can amplify out-of-order delivery of the
inner packet stream in the presence of packet
aggregation and any reordering.";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS), Section 2.5";
}
leaf lost-packet-timer-interval {
type decimal64 {
fraction-digits 6;
}
units "milliseconds";
description
"On reception, this interval defines the length of time
an IP-TFS receiver will wait for a missing packet before
considering it lost. If not using send-immediately,
then each lost packet will delay inner (user) packets
until this timer expires. Setting this value too low
can impact reordering and reassembly. The value is
configurable in milliseconds or fractional milliseconds
down to 1 nanosecond.";
reference
"RFC 9347: Aggregation and Fragmentation Mode for
Encapsulating Security Payload (ESP) and Its Use for
IP Traffic Flow Security (IP-TFS), Section 2.2.3";
}
}
}
/*
* IP-TFS ike configuration
*/
augment "/nsfike:ipsec-ike/nsfike:conn-entry/nsfike:spd/"
+ "nsfike:spd-entry/"
+ "nsfike:ipsec-policy-config/"
+ "nsfike:processing-info/"
+ "nsfike:ipsec-sa-cfg" {
description
"IP-TFS configuration for this policy.";
uses iptfs-config;
}
augment "/nsfike:ipsec-ike/nsfike:conn-entry/"
+ "nsfike:child-sa-info" {
description
"IP-TFS configured on this SA.";
uses iptfs-config {
refine "traffic-flow-security" {
config false;
}
}
}
/*
* IP-TFS ikeless configuration
*/
augment "/nsfikels:ipsec-ikeless/nsfikels:spd/"
+ "nsfikels:spd-entry/"
+ "nsfikels:ipsec-policy-config/"
+ "nsfikels:processing-info/"
+ "nsfikels:ipsec-sa-cfg" {
description
"IP-TFS configuration for this policy.";
uses iptfs-config;
}
augment "/nsfikels:ipsec-ikeless/nsfikels:sad/"
+ "nsfikels:sad-entry" {
description
"IP-TFS configured on this SA.";
uses iptfs-config {
refine "traffic-flow-security" {
config false;
}
}
}
/*
* packet counters
*/
augment "/nsfike:ipsec-ike/nsfike:conn-entry/"
+ "nsfike:child-sa-info" {
description
"Per-SA counters";
container ipsec-stats {
if-feature "ipsec-stats";
config false;
description
"IPsec per-SA packet counters.
tx = outbound, rx = inbound";
uses ipsec-tx-stat-grouping;
uses ipsec-rx-stat-grouping;
}
container iptfs-inner-pkt-stats {
if-feature "iptfs-stats";
config false;
description
"IP-TFS per-SA inner packet counters.
tx = outbound, rx = inbound";
uses iptfs-inner-tx-stat-grouping;
uses iptfs-inner-rx-stat-grouping;
}
container iptfs-outer-pkt-stats {
if-feature "iptfs-stats";
config false;
description
"IP-TFS per-SA outer packets counters.
tx = outbound, rx = inbound";
uses iptfs-outer-tx-stat-grouping;
uses iptfs-outer-rx-stat-grouping;
}
}
/*
* packet counters
*/
augment "/nsfikels:ipsec-ikeless/nsfikels:sad/"
+ "nsfikels:sad-entry" {
description
"Per-SA counters";
container ipsec-stats {
if-feature "ipsec-stats";
config false;
description
"IPsec per-SA packet counters.
tx = outbound, rx = inbound";
uses ipsec-tx-stat-grouping;
uses ipsec-rx-stat-grouping;
}
container iptfs-inner-pkt-stats {
if-feature "iptfs-stats";
config false;
description
"IP-TFS per-SA inner packet counters.
tx = outbound, rx = inbound";
uses iptfs-inner-tx-stat-grouping;
uses iptfs-inner-rx-stat-grouping;
}
container iptfs-outer-pkt-stats {
if-feature "iptfs-stats";
config false;
description
"IP-TFS per-SA outer packets counters.
tx = outbound, rx = inbound";
uses iptfs-outer-tx-stat-grouping;
uses iptfs-outer-rx-stat-grouping;
}
}
}
4. IANA Considerations
4.1. Updates to the IETF XML Registry
Per this document, IANA has registered a URI in the "IETF XML Registry" [RFC 3688] as follows.
- URI:
- urn:ietf:params:xml:ns:yang:ietf-ipsec-iptfs
- Registrant Contact:
- The IESG.
- XML:
- N/A; the requested URI is an XML namespace.
4.2. Updates to the YANG Module Names Registry
Per this document, IANA has registered one YANG module in the "YANG Module Names" registry [RFC 6020] as follows.
- Name:
- ietf-ipsec-iptfs
- Namespace:
- urn:ietf:params:xml:ns:yang:ietf-ipsec-iptfs
- Prefix:
- iptfs
- Reference:
- RFC 9348
5. Security Considerations
The YANG module specified in this document defines a schema for data that is designed to be accessed via network management protocols such as NETCONF [RFC 6241] or RESTCONF [RFC 8040]. The lowest NETCONF layer is the secure transport layer, and the mandatory-to-implement secure transport is Secure Shell (SSH) [RFC 6242]. The lowest RESTCONF layer is HTTPS, and the mandatory-to-implement secure transport is TLS [RFC 8446].
The Network Configuration Access Control Model (NACM) [RFC 8341] provides the means to restrict access for particular NETCONF or RESTCONF users to a preconfigured subset of all available NETCONF or RESTCONF protocol operations and content.
There are a number of data nodes defined in this YANG module that are writable/creatable/deletable (i.e., config true, which is the default). These data nodes may be considered sensitive or vulnerable in some network environments. Write operations (e.g., edit-config) to these data nodes without proper protection can have a negative effect on network operations. These are the subtrees and data nodes and their sensitivity/vulnerability:
- ../traffic-flow-security:
- Enabling IP-TFS is controlled by setting the entriesunder traffic-flow-security in IKE or IKE-less models. IP-TFSis set either to be congestion sensitive or a fixed rate by settingparameters in this subtree.
- ../iptfs-inner-pkt-stats and ../iptfs-outer-pkt-stats:
- Access to IP-TFS statistics can provide informationthat IP-TFS obscures, such as the true activity of the flowsusing IP-TFS.
6. References
6.1. Normative References
- [RFC4301]
-
S. Kent, and K. Seo, "Security Architecture for the Internet Protocol", RFC 4301, DOI 10.17487/RFC4301, December 2005,
<https://www.rfc-editor.org/info/ >.rfc4301 - [RFC6020]
-
M. Bjorklund, "YANG - A Data Modeling Language for the Network Configuration Protocol (NETCONF)", RFC 6020, DOI 10.17487/RFC6020, October 2010,
<https://www.rfc-editor.org/info/ >.rfc6020 - [RFC6241]
-
R. Enns, M. Bjorklund, J. Schoenwaelder, and A. Bierman, "Network Configuration Protocol (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
<https://www.rfc-editor.org/info/ >.rfc6241 - [RFC6242]
-
M. Wasserman, "Using the NETCONF Protocol over Secure Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, June 2011,
<https://www.rfc-editor.org/info/ >.rfc6242 - [RFC6991]
-
J. Schoenwaelder, "Common YANG Data Types", RFC 6991, DOI 10.17487/RFC6991, July 2013,
<https://www.rfc-editor.org/info/ >.rfc6991 - [RFC7950]
-
M. Bjorklund, "The YANG 1.1 Data Modeling Language", RFC 7950, DOI 10.17487/RFC7950, August 2016,
<https://www.rfc-editor.org/info/ >.rfc7950 - [RFC8040]
-
A. Bierman, M. Bjorklund, and K. Watsen, "RESTCONF Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
<https://www.rfc-editor.org/info/ >.rfc8040 - [RFC8341]
-
A. Bierman, and M. Bjorklund, "Network Configuration Access Control Model", STD 91, RFC 8341, DOI 10.17487/RFC8341, March 2018,
<https://www.rfc-editor.org/info/ >.rfc8341 - [RFC8342]
-
M. Bjorklund, J. Schoenwaelder, P. Shafer, K. Watsen, and R. Wilton, "Network Management Datastore Architecture (NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018,
<https://www.rfc-editor.org/info/ >.rfc8342 - [RFC8446]
-
E. Rescorla, "The Transport Layer Security (TLS) Protocol Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018,
<https://www.rfc-editor.org/info/ >.rfc8446 - [RFC9061]
-
R. Marin-Lopez, G. Lopez-Millan, and F. Pereniguez-Garcia, "A YANG Data Model for IPsec Flow Protection Based on Software-Defined Networking (SDN)", RFC 9061, DOI 10.17487/RFC9061, July 2021,
<https://www.rfc-editor.org/info/ >.rfc9061 - [RFC9347]
-
LabN Consulting, L.L.C., C Hopps, "Aggregation and Fragmentation Mode for Encapsulating Security Payload (ESP) and Its Use for IP Traffic Flow Security (IP-TFS)", RFC 9347, DOI 10.17487/RFC9347, January 2023,
<https://www.rfc-editor.org/info/ >.rfc9347
6.2. Informative References
- [RFC3688]
-
M. Mealling, "The IETF XML Registry", BCP 81, RFC 3688, DOI 10.17487/RFC3688, January 2004,
<https://www.rfc-editor.org/info/ >.rfc3688 - [RFC5348]
-
S. Floyd, M. Handley, J. Padhye, and J. Widmer, "TCP Friendly Rate Control (TFRC): Protocol Specification", RFC 5348, DOI 10.17487/RFC5348, September 2008,
<https://www.rfc-editor.org/info/ >.rfc5348 - [RFC8340]
-
M. Bjorklund, and L. Berger, "YANG Tree Diagrams", BCP 215, RFC 8340, DOI 10.17487/RFC8340, March 2018,
<https://www.rfc-editor.org/info/ >.rfc8340
Appendix A. Examples
The following examples show configuration and operational data for the IKE-less and IKE cases using XML and JSON. Also, the operational statistics for the IKE-less case is illustrated.
A.1. Example XML Configuration
This example illustrates configuration for IP-TFS in the IKE-less case. Note that, since this augments the IPsec IKE-less schema, only a minimal IKE-less configuration to satisfy the schema has been populated.
<i:ipsec-ikeless
xmlns:i="urn:ietf:params:xml:ns:yang:ietf-i2nsf-ikeless"
xmlns:tfs="urn:ietf:params:xml:ns:yang:ietf-ipsec-iptfs">
<i:spd>
<i:spd-entry>
<i:name>protect-policy-1</i:name>
<i:direction>outbound</i:direction>
<i:ipsec-policy-config>
<i:traffic-selector>
<i:local-prefix>192.0.2.0/16</i:local-prefix>
<i:remote-prefix>198.51.100.0/16</i:remote-prefix>
</i:traffic-selector>
<i:processing-info>
<i:action>protect</i:action>
<i:ipsec-sa-cfg>
<tfs:traffic-flow-security>
<tfs:congestion-control>true</tfs:congestion-control>
<tfs:packet-size>
<tfs:use-path-mtu-discovery
>true</tfs:use-path-mtu-discovery>
</tfs:packet-size>
<tfs:l2-fixed-rate>1000000000</tfs:l2-fixed-rate>
<tfs:max-aggregation-time
>0.1</tfs:max-aggregation-time>
<tfs:window-size>5</tfs:window-size>
<tfs:send-immediately>false</tfs:send-immediately>
<tfs:lost-packet-timer-interval
>0.2</tfs:lost-packet-timer-interval>
</tfs:traffic-flow-security>
</i:ipsec-sa-cfg>
</i:processing-info>
</i:ipsec-policy-config>
</i:spd-entry>
</i:spd>
</i:ipsec-ikeless>
A.2. Example XML Operational Data
This example illustrates operational data for IP-TFS in the IKE-less case. Note that, since this augments the IPsec IKE-less schema only, a minimal IKE-less configuration to satisfy the schema has been populated.
<i:ipsec-ikeless
xmlns:i="urn:ietf:params:xml:ns:yang:ietf-i2nsf-ikeless"
xmlns:tfs="urn:ietf:params:xml:ns:yang:ietf-ipsec-iptfs">
<i:sad>
<i:sad-entry>
<i:name>sad-1</i:name>
<i:ipsec-sa-config>
<i:spi>1</i:spi>
<i:traffic-selector>
<i:local-prefix>2001:db8:1::/48</i:local-prefix>
<i:remote-prefix>2001:db8:2::/48</i:remote-prefix>
</i:traffic-selector>
</i:ipsec-sa-config>
<tfs:traffic-flow-security>
<tfs:congestion-control>true</tfs:congestion-control>
<tfs:packet-size>
<tfs:use-path-mtu-discovery
>true</tfs:use-path-mtu-discovery>
</tfs:packet-size>
<tfs:l2-fixed-rate>1000000000</tfs:l2-fixed-rate>
<tfs:max-aggregation-time>0.100</tfs:max-aggregation-time>
<tfs:window-size>0</tfs:window-size>
<tfs:send-immediately>true</tfs:send-immediately>
<tfs:lost-packet-timer-interval
>0.200</tfs:lost-packet-timer-interval>
</tfs:traffic-flow-security>
</i:sad-entry>
</i:sad>
</i:ipsec-ikeless>
A.3. Example JSON Configuration
This example illustrates configuration data for IP-TFS in the IKE case. Note that, since this augments the IPsec IKE schema, only a minimal IKE configuration to satisfy the schema has been populated.
{
"ietf-i2nsf-ike:ipsec-ike": {
"ietf-i2nsf-ike:conn-entry": [
{
"name": "my-peer-connection",
"ike-sa-encr-alg": [
{
"id": 1,
"algorithm-type": 12,
"key-length": 128
}
],
"local": {
"local-pad-entry-name": "local-1"
},
"remote": {
"remote-pad-entry-name": "remote-1"
},
"ietf-i2nsf-ike:spd": {
"spd-entry": [
{
"name": "protect-policy-1",
"ipsec-policy-config": {
"traffic-selector": {
"local-prefix": "192.0.2.0/16",
"remote-prefix": "198.51.100.0/16"
},
"processing-info": {
"action": "protect",
"ipsec-sa-cfg": {
"ietf-ipsec-iptfs:traffic-flow-security": {
"congestion-control": true,
"l2-fixed-rate": "1000000000",
"packet-size": {
"use-path-mtu-discovery": true
},
"max-aggregation-time": "0.1",
"window-size": 1,
"send-immediately": false,
"lost-packet-timer-interval": "0.2"
}
}
}
}
}
]
}
}
]
}
}
A.4. Example JSON Operational Data
This example illustrates operational data for IP-TFS in the IKE case. Note that, since this augments the IPsec IKE tree, only a minimal IKE configuration to satisfy the schema has been populated.
{
"ietf-i2nsf-ike:ipsec-ike": {
"ietf-i2nsf-ike:conn-entry": [
{
"name": "my-peer-connection",
"ike-sa-encr-alg": [
{
"id": 1,
"algorithm-type": 12,
"key-length": 128
}
],
"local": {
"local-pad-entry-name": "local-1"
},
"remote": {
"remote-pad-entry-name": "remote-1"
},
"ietf-i2nsf-ike:child-sa-info": {
"ietf-ipsec-iptfs:traffic-flow-security": {
"congestion-control": true,
"l2-fixed-rate": "1000000000",
"packet-size": {
"use-path-mtu-discovery": true
},
"max-aggregation-time": "0.1",
"window-size": 5,
"send-immediately": false,
"lost-packet-timer-interval": "0.2"
}
}
}
]
}
}
A.5. Example JSON Operational Statistics
This example shows the JSON formatted statistics for IP-TFS. Note a unidirectional IP-TFS transmit side is illustrated, with arbitrary numbers for transmit.
{
"ietf-i2nsf-ikeless:ipsec-ikeless": {
"sad": {
"sad-entry": [
{
"name": "sad-1",
"ipsec-sa-config": {
"spi": 1,
"traffic-selector": {
"local-prefix": "192.0.2.1/16",
"remote-prefix": "198.51.100.0/16"
}
},
"ietf-ipsec-iptfs:traffic-flow-security": {
"window-size": 5,
"send-immediately": false,
"lost-packet-timer-interval": "0.2"
},
"ietf-ipsec-iptfs:ipsec-stats": {
"tx-pkts": "300",
"tx-octets": "80000",
"tx-drop-pkts": "2",
"rx-pkts": "0",
"rx-octets": "0",
"rx-drop-pkts": "0"
},
"ietf-ipsec-iptfs:iptfs-inner-pkt-stats": {
"tx-pkts": "250",
"tx-octets": "75000",
"rx-pkts": "0",
"rx-octets": "0",
"rx-incomplete-pkts": "0"
},
"ietf-ipsec-iptfs:iptfs-outer-pkt-stats": {
"tx-all-pad-pkts": "40",
"tx-all-pad-octets": "40000",
"tx-extra-pad-pkts": "200",
"tx-extra-pad-octets": "30000",
"rx-all-pad-pkts": "0",
"rx-all-pad-octets": "0",
"rx-extra-pad-pkts": "0",
"rx-extra-pad-octets": "0",
"rx-errored-pkts": "0",
"rx-missed-pkts": "0"
},
"ipsec-sa-state": {
"sa-lifetime-current": {
"time": 80000,
"bytes": "400606",
"packets": 1000,
"idle": 5
}
}
}
]
}
}
}
Acknowledgements
The authors would like to thank Eric Kinzie, Jürgen Schönwälder, Lou Berger, and Tero Kivinen for their feedback and review on the YANG module.
Authors' Addresses
Don Fedyk
LabN Consulting, L.L.C.
Email: dfedyk@labn.net
Christian Hopps
LabN Consulting, L.L.C.
Email: chopps@chopps.org
