Content for TS 25.153 Word version: 16.0.0
3 Definitions, symbols and abbreviations
4 Frequency bands and channel arrangement
5 General test conditions and declarations
6 Output power
7 Frequency stability
8 Out of band gain
9 Unwanted emission
10 Modulation accuracy
11 Input Intermodulation
12 Output Intermodulation
13 Adjacent Channel Rejection Ratio (ACRR)
14 Timing Accuracy
A Repeater measurement system set-up
B Derivation of Test Requirements
C Acceptable uncertainty of Test Equipment
$ Change history
3 Definitions, symbols and abbreviations |R10|
4 Frequency bands and channel arrangement |R10|
5 General test conditions and declarations |R10|
5.1 Acceptable uncertainty of Test System Word‑p. 10
5.2 Repeater test tolerances (informative)
5.3 Interpretation of measurement results Word‑p. 12
5.4 Test Environment
5.4.1 Normal test environment
5.4.2 Extreme test environment Word‑p. 13
5.4.3 Vibration
5.4.4 Power supply Word‑p. 14
5.5 Selection of configurations for testing
5.6 Regional requirements Word‑p. 15
5.7 Format and interpretation of tests
5.8 Repeater configurations Word‑p. 16
6 Output power |R10| Word‑p. 17
6.1 Definition and applicability
6.2 Minimum Requirements
6.3 Test purpose
6.4 Method of test
6.4.1 Initial conditions
6.4.2 Procedure Word‑p. 18
6.5 Test Requirements
7 Frequency stability |R10|
7.1 Definition and applicability Word‑p. 19
7.2 Minimum Requirement
7.3 Test purpose
7.4 Method of test
7.5 Test requirements
8 Out of band gain |R10|
8.1 Definitions and applicability
8.2 Minimum requirement Word‑p. 20
8.3 Test purpose
8.4 Method of test
8.5 Test requirements Word‑p. 21
9 Unwanted emission |R10|
9.1 Spectrum emission mask
9.1.1 Definition and applicability
9.1.2 Minimum Requirements
9.1.3 Test purpose Word‑p. 22
9.1.4 Method of test
9.1.5 Test Requirements Word‑p. 23
9.2 Spurious emissions Word‑p. 24
9.2.1 Definition and applicability
9.2.2 Minimum Requirements
9.2.2.1 Mandatory Requirements
9.2.2.2 Co-existence with GSM 900 Word‑p. 25
9.2.2.3 Co-existence with DCS 1800 Word‑p. 26
9.2.2.4 Co-existence with UTRA-FDD
9.2.2.5 Co-existence with unsynchronised TDD
9.2.3 Test purpose
9.2.4 Method of test Word‑p. 29
9.2.5 Test Requirements
10 Modulation accuracy |R10|
10.1 Error Vector Magnitude
10.1.1 Definition and applicability
10.1.2 Minimum requirements
10.1.3 Test purpose
10.1.4 Method of test Word‑p. 30
10.1.5 Test requirements
10.2 Peak code domain error
11 Input Intermodulation |R10|
11.1 Definition and applicability
11.2 Minimum requirement
11.2.1 General requirement
11.2.2 Co-location with BS in other systems Word‑p. 33
11.2.3 Co-existence with other systems Word‑p. 36
11.3 Test purpose Word‑p. 37
11.4 Method of test Word‑p. 38
11.5 Test requirements
12 Output Intermodulation |R10|
12.1 Definition and applicability
12.2 Minimum requirements
12.3 Test purpose
12.4 Method of test Word‑p. 39
12.5 Test requirements
13 Adjacent Channel Rejection Ratio (ACRR) |R10| Word‑p. 40
13.1 Definitions and applicability
13.2 Minimum Requirements
13.3 Test purpose
13.4 Method of test
13.4.1 Initial conditions
13.4.2 Procedure Word‑p. 41
13.5 Test Requirements
14 Timing Accuracy |R10|
14.1 Definition and applicability
14.2 Minimum requirements
14.3 Test purpose Word‑p. 42
14.4 Method of test
14.4.1 Initial conditions
14.4.2 Procedure Word‑p. 43
14.5 Test Requirements
A (Normative) Repeater measurement system set-up |R10| Word‑p. 45
A.1 Maximum output power
A.2 Frequency stability
A.3 Out of band gain
A.4 Unwanted emission: Spectrum emission mask
A.5 Unwanted emission: Spurious emission Word‑p. 46
A.6 Modulation Accuracy: Error Vector Magnitude
A.7 Modulation Accuracy: Peak Code Domain Error
A.8 Input inter modulation
A.9 Output Intermodulation Word‑p. 47
A.10 Timing Accuracy
B Derivation of Test Requirements |R10| Word‑p. 48
C Acceptable uncertainty of Test Equipment |R10| Word‑p. 49
$ Change history Word‑p. 50
