tech-invite   World Map     

IETF     RFCs     Groups     SIP     ABNFs    |    3GPP     Specs     Gloss.     Arch.     IMS     UICC    |    Misc.    |    search     info

ETSI (SCP TEST)
TS 102 230

 

 

 

 

Top

 

Up

 

Prev

 

Next

 

 

 

Smart Cards –
UICC-Terminal interface
Physical, Electrical and Logical Test specification

(P) V10.2.0    2015-03    85 p.
(P) V9.0.0    2013-04    83 p.
(P) V8.0.0    2010-04    83 p.
(P) V7.2.0    2010-04    9 p.
(P) V6.0.0    2010-04    9 p.
(P) V5.10.0    2010-04    9 p.
(P) V4.12.0    2010-04    9 p.
(P) V3.12.0    2010-04    9 p.


The present document defines the interface tests for the Terminal/UICC interface. The aim of the present document is to ensure interoperability between an UICC and a Terminal independently of the respective manufacturer, card issuer or operator.

Application specific tests for applications residing on an UICC are specified in 3GPP TS 31.121. The present document specifies the tests of:
  • physical characteristics of the UICC;
  • the electrical interface between the UICC and the Terminal;
  • the initial communication establishment and the transport protocols;
  • the application independent procedures.


1   Scope   p. 12
2   References
3   Definitions, symbols, abbreviations and coding conventions
4   Physical characteristic tests   p. 19
5   Electrical characteristic tests
5.1   Test of the power transition phases
5.1.1   Phase preceding Terminal power on      Up
5.1.2   Phase during UICC power on
5.1.3   Phase during Terminal power off   p. 23      Up
5.1.4   Warm reset timing   p. 25      Up
5.1.5   UICC type recognition and voltage switching   p. 26
5.2   Electrical tests on each Terminal contact   p. 31
5.2.1   Nominal test conditions
5.2.2   Electrical tests on contact C1
5.2.3   Electrical tests on contact C2
5.2.4   Electrical tests on contact C3
5.2.5   Electrical tests on contact C7
6   Initial communication tests
7   Transmission protocol tests   p. 57
7.1   Character transmission
7.2   T=0 protocol
7.2.1   Timing
7.2.2   Command processing, ACK, NACK, NULL procedure bytes
7.2.3   Case 2 command, use of procedure bytes '61xx' and '6Cxx'
7.2.4   Case 4 command, use of procedure bytes '61xx'   p. 62      Up
7.2.5   Command processing, warning and error status bytes
7.2.6   Error correction
7.2.7   Error detection
7.3   T=1 protocol
7.3.1   Character Waiting Time
7.3.2   Block Timing   p. 66
7.3.3   Block Waiting Time extension
7.3.4   Chaining - Respect of IFSC by Terminal
7.3.5   Chaining - IFSD management      Up
7.3.6   I-Block error correction   p. 72
7.3.7   I-Block error detection
7.3.8   R-Block error handling in non-chaining mode
7.3.9   R-Block error handling in chaining mode
7.3.10   Successive errors in both directions
7.3.11   Chaining - Abortion   p. 77
7.3.12   Block repetition and resynchronization      Up
7.3.13   UICC is unresponsive
8   Application dependent procedures   p. 81
A  (normative)   UICC simulator functional requirement   p. 82
B   Change history   p. 84

Top