tech-invite   World Map     

IETF     RFCs     Groups     SIP     ABNFs    |    3GPP     Specs     Gloss.     Arch.     IMS     UICC    |    Misc.    |    search     info

TS 08.02














Base Station System - Mobile Services Switching Centre (BSS-MSC) Interface - Interface Principles

(P) GSM Rel-99 v8.0.1    2002/06    19 p.
(P) GSM Rel-98 v7.0.0    1999/06    18 p.
(P) GSM Rel-97 v6.0.0    1998/10    18 p.
(P) GSM Rel-96 v5.1.0    1997/02    17 p.
(W) GSM Phase-2 v4.2.0    1995/01    20 p.
(P) GSM Phase-1 v3.3.1    1992/02    22 p.

Rapporteur:  ANDERSEN, Niels Peter Skov
Descendant(s):  TS 48.002    

This TS gives the principles on which the detailed interface specifications in the rest of the TS 08.0X series of Technical Specifications are based.

The set of fixed equipment accessed from the MSC through one particular instance of the interface will be later referred to as a Base Station System (BSS). A BSS ensures the coverage of n cells, where n can be 1 or more.

The function of a BSS may be further subdivided into a control function, performed by one Base Station Controller (BSC) and a transceiving function, performed by "n" Base Transceiver Station equipments (BTS), one for each cell. However, the study of such a split is outside the scope of the 08.0x series of Technical Specifications, where the BSS will be considered as a whole.

The BSS-MSC interface defined in the TS 08 series of Technical Specifications is designed to support a wide range of possible architectures on both sides. Characteristics like the physical location of the transcoders/rate adaptation inside the BSS (either integrated into the transceivers or very near to the MSC) or the use of traffic or signalling concentration at either side are left to the operators choice. Annex A to this TS contains guidance information concerning the use of remote mobile switching units, which for the purposes of this TS are considered as part of the MSC.

Direct connection between two BSSs is not supported by this interface.

This interface is based on the use of 1 or more 2048 kbit/s digital transmission system interfaces. Each 2048 kbit/s interface provides 31*64 kbit/s channels which can be used for traffic or signalling as the operator requires.

The signalling is layered, terminology similar to that in the OSI reference model is used in this series, however the layers referred to are not identical to the equivalently named layer in the OSI model.

This interface is defined at the boundary of the MSC and has a per channel bit rate of 64 kbit/s, but the net radio path traffic channel is at a rate of less than 16 kbit/s. A transcoder or rate adapter function is thus needed for the rate conversion. The interface is designed such that the transcoding or rate adaptation function may be geographically situated at either the MSC site or the BSS site, however the transcoder is considered to be part of the BSS.

The interface has been designed around the aims of TS 08.01 allowing each component and the system as a whole to evolve.

1   General   PDF-p. 6
2   Functional division between Base Station System (BSS) and MSC   PDF-p. 8
2.1   Terrestrial channel management   PDF-p. 9
2.2   Radio channel management
2.3   Resource indication
2.4   Channel coding decoding
2.5   Transcoding/rate adaptation   PDF-p. 11
2.6   Interworking function (data calls)
2.7   Measurement information
2.8   Handover
2.9   Mobility management      Up
2.10   Call control
2.11   Security features
3   Transcoder/rate adapter integration
4   Multiplexing of common and dedicated control channels
5   Classes of signalling messages
6   Support of services and features other than speech   PDF-p. 14      Up
7   Interface structures
8   Operation and maintenance
A   Remote Mobile Switching Unit (RMSU)   PDF-p. 16
B   Change History   PDF-p. 17